Pioneer SC-65 Operating Instruction
Operating Instructions
AV Receiver
SC-65
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 20 cm at top, 10 cm at rear, and 20 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
D3-4-2-1-3_A1_En
D3-4-2-1-4*_A1_En
D3-4-2-1-7a_A1_En
D3-4-2-1-7b*_A1_En
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D3-4-2-1-1_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-1-7c*_A1_En
D3-4-2-2-1a_A1_En
D3-4-2-2-2a*_A1_En
11)
Read these instructions.
1)
Keep these instructions.
2)
Heed all warnings.
3)
Follow all instructions.
4)
Do not use this apparatus near water.
5)
Clean only with dry cloth.
6)
Do not block any ventilation openings. Install in
7)
Only use attachments/accessories specified by
the manufacturer.
12)
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as
8)
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
9)
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
10)
pinched particularly at plugs, convenience
13)
Unplug this apparatus during lightning storms
or when unused for long periods of time.
14)
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
receptacles, and the point where they exit from
the apparatus.
D3-7-13-69_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Caution
To prevent fire hazard, the Class 2 Wiring Cable
should be used for connection with speaker, and
should be routed away from hazards to avoid damage
to the insulation of the cable.
D3-7-13-67*_A1_En
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product may expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
Information to User
D8-10-1-2_A1_En
D36-P5_B1_En
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En
2
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED
WARRANTY CARD AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
D36-AP9-1_A1_En
CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.
D8-10-3a_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
This Class B digital apparatus complies with
Canadian ICES-003.
D8-10-1-3_A1_En
CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal
heatsink may become hot when
operating this product continuously.
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En
3
Thank you for buying this Pioneer product. Please read through these operating
instructions so you will know how to operate your model properly.
Contents
01 Before you start
Checking what’s in the box ................................................................................................................................................ 8
Our philosophy .................................................................................................................................................................... 8
Features ............................................................................................................................................................................... 8
Installing the receiver ......................................................................................................................................................... 9
Loading the batteries .......................................................................................................................................................... 9
Operating range of remote control unit..........................................................................................................................10
About using AVNavigator (included CD-ROM)..............................................................................................................10
04 Basic Setup
Changing the OSD display language (OSD Language) ................................................................................................42
Automatically conducting optimum sound tuning (Full Auto MCACC) .....................................................................42
The Input Setup menu ......................................................................................................................................................44
Operation Mode Setup .....................................................................................................................................................45
About the Home Menu.....................................................................................................................................................45
05 Basic playback
Playing a source ...............................................................................................................................................................47
Playing an iPod .................................................................................................................................................................48
Playing a USB device .......................................................................................................................................................49
Playing an MHL-compatible device ................................................................................................................................50
Listening to the radio ........................................................................................................................................................51
Bluetooth ADAPTER for Wireless Enjoyment of Music ................................................................................................52
02 Controls and displays
Remote control .................................................................................................................................................................12
Display ...............................................................................................................................................................................14
Front panel ........................................................................................................................................................................15
03 Connecting your equipment
Connecting your equipment ............................................................................................................................................18
Rear panel .........................................................................................................................................................................18
Determining the speakers’ application ..........................................................................................................................19
Placing the speakers ........................................................................................................................................................21
Connecting the speakers .................................................................................................................................................22
Installing your speaker system ........................................................................................................................................23
About the audio connection ............................................................................................................................................27
About the video converter ................................................................................................................................................27
About HDMI ......................................................................................................................................................................28
Connecting your TV and playback components ............................................................................................................28
Connecting an HDD/DVD recorder, BD recorder and other video sources ...............................................................31
Connecting a satellite/cable receiver or other set-top box ...........................................................................................32
Connecting other audio components .............................................................................................................................33
Connecting additional amplifiers ....................................................................................................................................33
Connecting AM/FM antennas .........................................................................................................................................34
MULTI-ZONE setup ...........................................................................................................................................................35
Connecting to the network through LAN interface .......................................................................................................37
Connecting optional Bluetooth ADAPTER .....................................................................................................................37
Connecting an iPod ..........................................................................................................................................................37
Connecting a USB device ................................................................................................................................................38
Connecting an MHL-compatible device .........................................................................................................................38
Connecting an HDMI-equipped component to the front panel input .........................................................................38
Connecting to a wireless LAN .........................................................................................................................................39
Connecting an IR receiver ...............................................................................................................................................39
Switching components on and off using the 12 volt trigger .........................................................................................39
Plugging in the receiver ...................................................................................................................................................40
06 Listening to your system
Enjoying various types of playback using the listening modes ....................................................................................55
Selecting MCACC presets ...............................................................................................................................................57
Choosing the input signal ................................................................................................................................................57
Better sound using Phase Control ..................................................................................................................................58
Better sound using Phase Control and Full Band Phase Control ...............................................................................58
07 Playback with NETWORK features
Introduction ....................................................................................................................................................................... 60
Playback with Network functions....................................................................................................................................61
About network playback...................................................................................................................................................62
About playable file formats ..............................................................................................................................................64
08 Control with HDMI function
About the Control with HDMI function ...........................................................................................................................66
Making Control with HDMI connections ........................................................................................................................66
HDMI Setup.......................................................................................................................................................................66
Before using synchronization ..........................................................................................................................................67
About synchronized operations ......................................................................................................................................67
Setting the PQLS function ...............................................................................................................................................67
About Sound Retriever Link and Stream Smoother Link ..............................................................................................67
Cautions on the Control with HDMI function ................................................................................................................68
09 Using other functions
Setting the Audio options ................................................................................................................................................70
Setting the Video options .................................................................................................................................................72
Switching the speaker terminals ....................................................................................................................................74
Using the MULTI-ZONE controls .....................................................................................................................................75
Making an audio or a video recording ............................................................................................................................75
Network settings from a web browser ............................................................................................................................75
Using the sleep timer .......................................................................................................................................................76
Dimming the display ........................................................................................................................................................76
Switching the HDMI output .............................................................................................................................................76
Checking your system settings .......................................................................................................................................76
Resetting the system ........................................................................................................................................................76
4
10 Controlling the rest of your system
About the Remote Setup menu.......................................................................................................................................79
Operating multiple receivers ...........................................................................................................................................79
Setting the remote to control other components ..........................................................................................................79
Selecting preset codes directly .......................................................................................................................................79
Programming signals from other remote controls .......................................................................................................80
Erasing one of the remote control button settings ........................................................................................................80
Erasing all learnt settings that are in one input function .............................................................................................80
Direct function ..................................................................................................................................................................81
Setting the backlight mode .............................................................................................................................................81
About the ALL ZONE STBY (All Zone Standby) and DISCRETE ON (Discrete On) functions ....................................81
Resetting the remote control settings ............................................................................................................................81
Controlling components ..................................................................................................................................................82
11 The Advanced MCACC menu
Making receiver settings from the Advanced MCACC menu ......................................................................................85
Automatic MCACC (Expert) .............................................................................................................................................85
Manual MCACC setup .....................................................................................................................................................87
Checking MCACC Data ....................................................................................................................................................89
Data Management............................................................................................................................................................90
12 The System Setup and Other Setup menus
Making receiver settings from the System Setup menu...............................................................................................93
Manual speaker setup ......................................................................................................................................................93
Network Setup menu .......................................................................................................................................................95
Checking the Network Information .................................................................................................................................96
The Other Setup menu .....................................................................................................................................................97
MHL Setup ........................................................................................................................................................................99
13 FAQ
Troubleshooting ..............................................................................................................................................................101
Power ...............................................................................................................................................................................101
No sound .........................................................................................................................................................................101
Other audio problems ....................................................................................................................................................102
ADAPTER PORT terminal ..............................................................................................................................................103
Video ................................................................................................................................................................................103
Settings ............................................................................................................................................................................103
Professional Calibration EQ graphical output .............................................................................................................104
Display .............................................................................................................................................................................104
Remote control ...............................................................................................................................................................104
HDMI ................................................................................................................................................................................104
AVNavigator ....................................................................................................................................................................105
USB interface ..................................................................................................................................................................106
iPod ..................................................................................................................................................................................106
Network ...........................................................................................................................................................................106
Web Control ....................................................................................................................................................................107
Wireless LAN ...................................................................................................................................................................108
14 Additional information
Surround sound formats ...............................................................................................................................................110
About THX .......................................................................................................................................................................110
About iPod .......................................................................................................................................................................111
About SiriusXM ...............................................................................................................................................................111
About FLAC .....................................................................................................................................................................111
Windows 7 .......................................................................................................................................................................112
MHL..................................................................................................................................................................................112
Auto Surround, ALC and Stream Direct with different input signal formats ............................................................112
Speaker Setting Guide....................................................................................................................................................113
About messages displayed when using network functions .......................................................................................114
Important information regarding the HDMI connection ............................................................................................114
Cleaning the unit ............................................................................................................................................................114
Glossary ...........................................................................................................................................................................115
Features index .................................................................................................................................................................118
Specifications .................................................................................................................................................................119
Preset code list................................................................................................................................................................120
5
Flow of settings on the receiver
Flow for connecting and setting the receiver
The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used easily after following the procedure below to make the connections and settings.
Required setting item: 1, 2, 3, 4, 5, 7, 9
Setting to be made as necessary: 6, 8, 10, 11, 12, 13
Important
The receiver’s initial settings can be made on the computer using Wiring Navi on the AVNavigator CD-ROM
included with the receiver. In this case, virtually the same connections and settings as in steps 2, 3, 4, 5, 6, 7
and 8 can be made interactively. For instructions on using AVNavigator, see About using AVNavigator (included
CD-ROM) on page 10.
1 Before you start
! Checking what’s in the box on page 8
! Loading the batteries on page 9
j
2 Determining the speakers’ application (page 19)
! [A] 9.2 channel surround system (Front height/Front wide) connection
! [B] 7.2 channel surround system & Speaker B connection
! [C] 7.2 channel surround system & Front Bi-amping connection (High quality surround)
! [D] 7.2 channel surround system (Surround back) & ZONE 2 connection (Multi Zone)
! [E] 7.2 channel surround system (Front height/Front wide) & ZONE 2 connection (Multi Zone)
! [F] 5.2 channel surround system & Front Bi-amping connection (High quality surround) & ZONE 2 connection
(Multi Zone)
! [G] 5.2 channel surround system & ZONE 2/ZONE 3 connection (Multi Zone)
j
3 Connecting the speakers
! Placing the speakers on page 21
! Connecting the speakers on page 22
! Installing your speaker system on page 23
! Bi-amping your speakers on page 22
j
4 Connecting the components
! About the audio connection on page 27
! About the video converter on page 27
! Connecting your TV and playback components on page 28
! Connecting AM/FM antennas on page 34
! Plugging in the receiver on page 40
j
5 Power On
j
6 Changing the OSD display language (OSD Language) (page 42)
j
7 MCACC speaker settings
! Automatically conducting optimum sound tuning (Full Auto MCACC) on page 42
j
8 The Input Setup menu (page 44)
(When using connections other than the recommended connections)
j
9 Basic playback (page 46)
j
10 Switching the HDMI output (page 76)
j
11 Adjusting the sound and picture quality as desired
! Using the various listening modes (page 54)
! Better sound using Phase Control (page 58)
! Better sound using Phase Control and Full Band Phase Control (page 58)
! Measuring the all EQ type (SYMMETRY/ALL CH ADJ/FRONT ALIGN) (page 85)
! Changing the channel level while listening (page 94)
! Switching on/off the Acoustic Calibration EQ, Auto Sound Retriever or Dialog Enhancement (page 70)
! Setting the PQLS function (page 67)
! Setting the Audio options (page 70)
! Setting the Video options (page 72)
j
12 Other optional adjustments and settings
! Control with HDMI function (page 65)
! The Advanced MCACC menu (page 84)
! The System Setup and Other Setup menus (page 92)
j
13 Making maximum use of the remote control
! Operating multiple receivers (page 79)
! Setting the remote to control other components (page 79)
6
Before you start
Checking what’s in the box ............................................................................................................8
Our philosophy ................................................................................................................................ 8
Features ............................................................................................................................................ 8
Installing the receiver ...................................................................................................................... 9
Loading the batteries ...................................................................................................................... 9
Operating range of remote control unit ......................................................................................10
About using AVNavigator (included CD-ROM) ........................................................................... 10
7
01
Before you start
Checking what’s in the box
Please check that you’ve received the following supplied accessories:
! Setup microphone (cable: 5 m (16.4 ft.))
! Remote control unit
! AAA size IEC R03 dry cell batteries (to confirm system operation) x2
! AM loop antenna
! FM wire antenna
! iPod cable
! MHL cable
! Power cord
! CD-ROM (AVNavigator)
! Quick start guide
! Safety Brochure
! Warranty sheet
Our philosophy
Pioneer is dedicated to making your home theater listening experience as close as possible to the vision of the
moviemakers and mastering engineer when they created the original soundtrack. We do this by focusing on three
important steps:
1 Designing with carefully selected components so as to transmit the original soundtrack
accurately
2 Allowing for customized acoustic calibration according to any listening area
3 Tuning that transmits soul
Features
% Class D Amplifier
This unit is an AV receiver developed based on the latest high performance Class D amplifier and integrating
the essence of Pioneer’s high sound quality designs. This new generation reference amplifier offers outstanding
performance with high sound quality and reproduces the latest in multi-channel digital contents.
% Apple AirPlay
With AirPlay you can stream music from iTunes to the SC-65 and play it through your home theater system.
You can even use the receiver to view metadata including song title, artist as well as album art on a connected
display. With Pioneer’s Air Play-compatible receivers, you can easily enjoy your iTunes music in any room in the
house.
% Air Jam App compatible
For the SC-65, the optional AS-BT200 Bluetooth adapter works together with Pioneer’s exclusive Air Jam application. Available free App in App Store and Android Market, Air Jam allows up to 4 iPhone, iPod touch, iPad or
Android devices to share music and create a group playlist for a unique and fun social music network experience.
% MHLTM (Mobile High-definition Link)-compatible device playback
An MHL-compatible mobile device can be connected to enjoy full-HD videos, high quality multi-channel audio,
and photos etc., with charge the battery on the receiver.
Also, MHL-compatible devices can be operated with the receiver’s remote control.
®
% AVNavigator
The CD-ROM (AVNavigator) included with this unit provides a variety of functions, such as Wiring Navi with a
guide for connecting the unit and setting up from the computer and an Interactive Manual for operating the
unit while reading the manual.
Also, Operation Guide describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
AVNavigator is not only included PC software, but also iPad version in free download from App Store. For detail,
check the website: http://pioneer.jp/product/soft/iapp_avnavi/en.html
% HDMI (3D, Audio Return Channel)
A compatible component is required to use the above function.
% 4K Pass Through
Displays 4K resolution video signals pass-through on the display.
% PQLS Bit-stream
Jitterless high quality playback is possible by connecting a PQLS-compatible player with HDMI connections.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.
% Auto Phase Control Plus
For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the first
place. This function automatically corrects for phase shifting on such discs and broadcast.
This function is especially effective when playing music.
% Hi-bit 32
Creates a wider dynamic range with digital sources like CDs, DVDs or BDs. 16-, 20- and 24-bit PCM as well as
compressed audio is requantized to 32 bits, and the high frequency component is interpolated upon data processing to enable smoother, more subtle musical expression.
% Sound Retriever Link
By connecting a Pioneer player supporting the Sound Retriever Link function, compressed audio files played on
the player can be corrected automatically to play the sound with higher density.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.
% Virtual Wide speaker
When you’re not using front wide speakers, selecting this mode allows you to hear a virtual front wide channel
through your front speakers.
This improves the continuity of the sound from the front channel to the surround channels.
% Stream Smoother Link
By connecting a Pioneer player supporting the Stream Smoother Link function, compressed video or movie files
played on the player can be corrected automatically to play them with a more natural, easily viewable picture.
This feature is only available when the connected Pioneer Blu-ray Disc Player supporting the PQLS function.
% iPod playback
Your iPod, iPhone or iPad can be connected to the receiver’s USB terminal and RCA video terminal to play the
music/video files on the iPod, iPhone or iPad.
Also, the iPod, iPhone or iPad is charged when it is connected to the receiver.
% Dolby Pro Logic llz compatible
Adding a pair of speakers above the front left and right speakers adds expressiveness in the vertical direction to
the previous horizontally-oriented sound field. The height channel strengthens the sound field’s sense of threedimensionality and air, producing presence and expansion.
% Internet Radio
By connecting this receiver to the network via the LAN terminal, you can listen to Internet radio stations.
8
01
Before you start
% Bluetooth compatible
Using the Bluetooth ADAPTER (AS-BT100 or AS-BT200) lets you enjoy music files on an iPhone or other Bluetooth
wireless technology device wirelessly.
% Auto Sound Retriever
The Auto Sound Retriever feature employs DSP technology to restore sound pressure and smooth jagged artifacts left over after compression.
% Easy setup using Advanced MCACC
The Auto MCACC Setup provides a quick but accurate surround sound setup, which includes the advanced features of Professional Acoustic Calibration EQ.
Installing the receiver
! When installing this unit, make sure to put it on a level and stable surface.
! Don’t install it on the following places:
— on a color TV (the screen may distort)
— near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with the sound.
— in direct sunlight
— in damp or wet areas
— in extremely hot or cold areas
— in places where there is vibration or other movement
— in places that are very dusty
— in places that have hot fumes or oils (such as a kitchen)
! Do not touch this receiver’s bottom panel while the power is on or just after it is turned off. The bottom panel
becomes hot when the power is on (or right after it is turned off) and could cause burns.
Loading the batteries
The batteries included with the unit are to check initial operations; they may not last over a long period. We recommend using alkaline batteries that have a longer life.
WARNING
! Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.
CAUTION
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
! Never use new and old batteries together.
! Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
! Batteries with the same shape may have different voltages. Do not use different batteries together.
! When disposing of used batteries, please comply with governmental regulations or environmental public insti-
tution’s rules that apply in your country/area.
9
01
Before you start
Operating range of remote control unit
The remote control may not work properly if:
! There are obstacles between the remote control and the receiver’s remote sensor.
! Direct sunlight or fluorescent light is shining onto the remote sensor.
! The receiver is located near a device that is emitting infrared rays.
! The receiver is operated simultaneously with another infrared remote control unit.
30°
30°
7 m (23 ft.)
About using AVNavigator (included CD-ROM)
The included AVNavigator CD-ROM contains Wiring Navi allowing you to easily make the receiver’s connections
and initial settings in dialog fashion. High precision initial settings can be completed easily simply by following
the instructions on the screen to make the connections and settings.
There are also other features enabling easy use of various functions, including an Interactive Manual that operates in association with the receiver, updating of various types of software, and MCACC Application that lets you
check the MCACC measurement results on 3D graphs.
Installing AVNavigator
1 Load the included CD-ROM into your computer’s CD drive.
The CD-ROM’s top menu screen appears.
2 Click ‘Install AVNavigator’ from the CD-ROM top menu.
3 Follow the instructions on the screen to install.
When “Finish” is selected, installation is completed.
4 Remove the included CD-ROM from the computer’s CD drive.
Handling the CD-ROM
Operating Environment
! AVNavigator can be used with Microsoft® Windows® XP/Vista/7.
! A browser is at times used for AVNavigator functions. The supported browser is Microsoft Internet Explorer 8
or 9.
! Adobe® Flash® Player 10 must be installed to use some of the functions in AVNavigator.
For details, see http://www.adobe.com/downloads/.
Precautions For Use
! This CD-ROM is for use with a personal computer. It cannot be used with a DVD player or music CD player.
Attempting to play this CD-ROM with a DVD player or music CD player can damage speakers or cause
impaired hearing due to the large volume.
License
! Please agree to the “Terms of Use” indicated below before using this CD-ROM. Do not use if you are unwilling
to consent to the terms of its use.
Terms of Use
! Copyright to data provided on this CD-ROM belongs to PIONEER CORPORATION. Unauthorized transfer,
duplication, broadcast, public transmission, translation, sales, lending or other such matters that go beyond
the scope of “personal use” or “citation” as defined by Copyright Law may be subject to punitive actions.
Permission to use this CD-ROM is granted under license by PIONEER CORPORATION.
General Disclaimer
! PIONEER CORPORATION does not guarantee the operation of this CD-ROM with respect to personal com-
puters using any of the applicable OS. In addition, PIONEER CORPORATION is not liable for any damages
incurred as a result of use of this CD-ROM and is not responsible for any compensation. The names of private
corporations, products and other entities described herein are the registered trademarks or trademarks of their
respective firms.
Using AVNavigator
1 Click [AVNavigator 2012.III] on the desktop to launch AVNavigator.
AVNavigator is launched and Wiring Navi starts up. The language selection screen appears. Follow the instructions on the screen to make the connections and automatic settings.
Wiring Navi only starts up automatically the first time AVNavigator is launched.
2 Select and use the desired function.
AVNavigator includes the following functions:
! Wiring Navi – Guides you through connections and initial settings in dialog fashion. High precision initial
settings can be made easily.
! Operation Guide – Describes the receiver’s playback operations and how to use several functions through
videos and illustrations.
! Interactive Manual – Automatically displays the pages explaining the functions that have been operated on
the receiver. It is also possible to operate the receiver from the Interactive Manual.
! Glossary – Displays glossary pages.
! MCACC Appli – Displays Advanced MCACC measurement results vividly on the computer.
There are special operating instructions for MCACC Application. These instructions are included in the
AVNavigator Interactive Manual’s menus. Refer to them when using MCACC Application.
! Software Update – Allows various types of software to be updated.
! Settings – Used to make various AVNavigator settings.
! Detection – Used to detect the receiver.
Deleting the AVNavigator
You can use the following method to uninstall (delete) the AVNavigator from your PC.
% Delete from the Control Panel of the PC.
From the Start menu, click “Program” d “PIONEER CORPORATION” d “AVNavigator 2012.III” d “Uninstall
AVNavigator 2012.III”.
10
Controls and displays
Remote control ..............................................................................................................................12
Display ............................................................................................................................................ 14
Front panel ..................................................................................................................................... 15
11
02
Controls and displays
Remote control
This section explains how to operate the remote control for the receiver.
2,3
10
1
4
5
6
7
8
9
5
ALL ZONE STBY
DISCRETE ON
RCU SETUP
BD DVDDVR
CDTV
USB CBL
SATMHL TUNER
iPod
INPUT
SELECT
TV CONTROL
CH
AUDIO
PARAMETER
TOP MENU
HOME
MENU
iPod CTRL
FEATURES
PQLS
PHASE
MPX
PRESET TUNE
AUTO/ALC/
DIRECT
STANDARD ADV SURR
222
13
SIGNAL SEL MCACC
546
DIMMER
SPEAKERS
8
79
HDMI OUT
D.ACCESS
/ CLR
0
ZONE 2 ZONE 3 ZONE 4
Z2 Z3 Z4
RECEIVER
INPUT
VOL
ENTER
BAND
BDR
NET
STATUS
Hi-Bit
CH LEVEL
SLEEP
CLASS
ENTER
SOURCERECEIVER
HDMI
ADPT
RECEIVER
VOLUME
MUTE
VIDEO
PARAMETER
TOOLS
MENU
RETURN
D.FILT
PTY
THX
+Favorite
AUDIO
AUTO
S.RTRV
DISP
CH
CH
LIGHT
11
12
13
14
15
The remote has been conveniently color-coded according to component control using the following system:
! White – Receiver control, TV control
! Blue – Other controls (See pages 48, 49, 51, 52 and 82.)
1 u RECEIVER
This switches between standby and on for this receiver.
2 ALL ZONE STBY DISCRETE ON
Use this button to perform unique operations (page 81).
3 RCU SETUP
Use to input the preset code when making remote control settings and to set the remote control mode (page 79).
4 Input function buttons
Press to select control of other components (page 79).
Use INPUT SELECT c/ d to select the input function (page 47).
5 Receiver Control buttons
Press first to access:
! STATUS – Press to check selected receiver settings (page 76).
! AUTO/ALC/DIRECT – Switches between Auto Surround (page 55), Auto Level Control, Optimum Surround
mode and Stream Direct mode (page 57).
! STANDARD – Press for Standard decoding and to switch various modes (2 Pro Logic, Neo:X, etc.) (page
55).
! ADV SURR – Use to switch between the various surround modes (page 56).
! THX – Press to select a Home THX listening mode (page 56).
! SIGNAL SEL – Use to select an input signal (page 57).
! MCACC – Press to switch between MCACC presets (page 57).
! CH LEVEL – Press repeatedly to select a channel, then use k/l to adjust the level (page 94).
! AUTO S.RTRV – Press to restore CD quality sound to compressed audio sources (page 70).
! SPEAKERS – Use to change the speaker terminal (page 74).
! DIMMER – Dims or brightens the display (page 76).
! SLEEP – Use to put the receiver in sleep mode and select the amount of time before sleep (page 76).
! HDMI OUT – Switch the HDMI output terminal (page 76).
6 TV CONTROL buttons
These buttons can be used to perform operations on the TV to which the TV CONTROL INPUT button is assigned.
The TV can be operated with these buttons regardless of the input set for the remote control’s operation mode
(page 79).
7 Receiver setting buttons
Press first to access:
! AUDIO PARAMETER – Use to access the Audio options (page 70).
! VIDEO PARAMETER – Use to access the Video options (page 72).
! HOME MENU – Use to access the Home Menu (pages 42, 44, 66, 85 and 93).
! RETURN – Press to confirm and exit the current menu screen.
8 i/j/k/l/ENTER
Use the arrow buttons when setting up your surround sound system (see page 85) and the Audio or Video options
(page 70 or 72).
9 FEATURES buttons
These let you operate the receiver’s features directly.
! PHASE – Press to switch on/off Phase Control or Full Band Phase Control (page 58).
! PQLS – Press to select the PQLS setting (page 67).
! Hi-Bit – Press to switch on/off the Hi-Bit 32 setting (page 70).
! D.FILT – Press to select the AUDIO DAC (Digital Audio Converter) digital filter type (page 70).
12
02
10 MULTI-ZONE select buttons
Switch to perform operations in ZONE 2 and ZONE 3 (page 75).
11 Remote control LED
Lights when a command is sent from the remote control.
12
Switches the remote to control the receiver (used to select the white commands).
Switch to perform operations in the main zone.
Also use this button to set up surround sound.
13 VOLUME +/–
Use to set the listening volume.
14 MUTE
Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound).
15 LIGHT
Press to turn on/off the illumination for the buttons.
The way the buttons light can be selected from four modes (page 81).
Note
! With this receiver, ZONE 4 button cannot be used.
Controls and displays
13
02
Controls and displays
Display
21 3 864 1075 11 13 14
2
AUTO
HDMI
DIGITAL
ANALOG
AUTO SURROUND
STREAM DIRECT
2
PROLOGIC x
THX ADV.SURROUND
STANDARD
SP AB
6
L C R
SL SR
XL XR
XC
LFE
Neo:6
SLEEP
DIGITAL PLUS
2
TrueHD
DTS HD ES 96/24
CD
MSTR
DSD PCM
MULTI-ZONE
S.RTRV SOUND UP MIX
TUNER
iPod
FULL BAND
PQLS
DVD
BD
2019 2116 17 18
ALC
TV
DVR
1 Signal indicators
Light to indicate the currently selected input signal. AUTO lights when the receiver is set to select the input signal automatically (page 57).
2 Program format indicators
Light to indicate the channels to which digital signals are being input.
! L/R – Left front/Right front channel
! C – Center channel
! SL/SR – Left surround/Right surround channel
! LFE – Low frequency effects channel (the (( )) indicators light when an LFE signal is being input)
! XL/XR – Two channels other than the ones above
! XC – Either one channel other than the ones above, the mono surround channel or matrix encode flag
3 Digital format indicators
Light when a signal encoded in the corresponding format is detected.
! 2 DIGITAL – Lights with Dolby Digital decoding.
! 2 DIGITAL PLUS – Lights with Dolby Digital Plus decoding.
! 2 TrueHD – Lights with Dolby TrueHD decoding.
! DTS – Lights with DTS decoding.
! DTS HD – Lights with DTS-HD decoding.
! 96/24 – Lights with DTS 96/24 decoding.
! DSD PCM – Light during DSD (Direct Stream Digital) to PCM conversion with SACDs.
! PCM – Lights during playback of PCM signals.
! MSTR – Lights during playback of DTS-HD Master Audio signals.
4 MULTI-ZONE
Lights when the MULTI-ZONE feature is active (page 75).
5 FULL BAND
Lights when the Full Band Phase Control is switched on (page 58).
6 Listening mode indicators
! AUTO SURROUND – Lights when the Auto Surround feature is switched on (page 55).
! ALC – Lights when the ALC (Auto level control) mode is selected (page 55).
! STREAM DIRECT – Lights when Direct/Pure Direct is selected (page 57).
! ADV.SURROUND – Lights when one of the Advanced Surround modes has been selected (page 56).
! STANDARD – Lights when one of the Standard Surround modes is switched on (page 55).
! THX – Lights when one of the Home THX modes is selected (page 56).
7 (PHASE CONTROL)
Lights when the Phase Control (page 58) or Full Band Phase Control (page 58) is switched on.
AT T
OVER
VIDEO
9 12
TUNED
STEREO
MONO
HDMI
[ 2 ]
USB
[ 3 ]
dB
[ 4 ]
8 Analog signal indicators
Light to indicate reducing the level of an analog signal (page 70).
9 PQLS
15
Lights when the PQLS feature is active (page 67).
10 Tuner indicators
! TUNED – Lights when a broadcast is being received.
! STEREO – Lights when a stereo FM broadcast is being received in auto stereo mode.
! MONO – Lights when the mono mode is set using MPX.
11
Lights when the sound is muted.
12 SOUND
Lights when the DIALOG E (Dialog Enhancement) or TONE (tone controls) features is selected (page 70).
13 Master volume level
Shows the overall volume level.
“---” indicates the minimum level, and “+12dB” indicates the maximum level.
14 Input function indicators
Light to indicate the input function you have selected.
15 Scroll indicators
Light when there are more selectable items when making the various settings.
16 Speaker indicators
Lights to indicate the current speaker system using SPEAKERS (page 74).
17 SLEEP
Lights when the receiver is in sleep mode (page 76).
18 Matrix decoding format indicators
! 2PRO LOGIC IIx – This lights to indicate 2 Pro Logic II / 2 Pro Logic IIx decoding (page 55).
19 S.RTRV
Lights when the Auto Sound Retriever function is active (page 70).
20 Character display
Displays various system information.
21 Remote control mode indicator
Lights to indicate the receiver’s remote control mode setting. (Not displayed when set to 1.) (page 97)
14
02
35
Controls and displays
Front panel
1 2 4
ADVANCED
MCACC
FL OFF
INPUT
SELECTOR
STANDBY/ON
8910 1211 13 14
AUDIO
PARAMETER
7
HOME MENU RETURN
TUNE
ENTER
TUNE
VIDEO
PARAMETER
PRESETPRESET
BAND
TUNER EDIT
MULTI-ZONE
CONTROLON/OFF
PHONES
SPEAKERS
MCACC
SETUP MIC
iPod iPhone iPad
DIRECT CONTROL
AUTO SURR/ALC/
STREAM DIRECTHOME THX
5V 2.1 A 5V 1 A
iPod iPhone iPad
15 16 17 1918 20 21
1 u STANDBY/ON
This switches between standby and on for this receiver.
2 INPUT SELECTOR dial
Use to select an input function.
3 Indicators
! ADVANCED MCACC – Lights when EQ is set to ON in the AUDIO PARAMETER menu (page 70).
! FL OFF – Lights when “off” (nothing displayed) is selected with the display’s dimmer adjustment (page 76).
! HDMI – Blinks when connecting an HDMI-equipped component; lights when the component is connected
(page 28).
! iPod iPhone iPad – Lights to indicate iPod/iPhone/iPad is connected (page 37).
4 Character display
See Display on page 14.
5 Remote sensor
Receives the signals from the remote control (page 10).
3
iPod iPhone iPadHDMI
STANDARD
SURROUND
USBHDMI 5 INPUT/
MHL ( )
ADVANCED
SURROUND
MASTER
VOLUME
6 MASTER VOLUME dial
7 Front panel controls
To access the front panel controls, catch the sides of the door with your fingers and pull forward.
6
INPUT
SELECTOR
STANDBY/ON
MASTER
VOLUME
8 AUDIO PARAMETER
Use to access the Audio options (page 70).
9 i/j/k/l (TUNE/PRESET) /ENTER
Use the arrow buttons when setting up your Home Menu. Use TUNE i/j to find radio frequencies and use
PRESET k/l to find preset stations (page 51).
10 VIDEO PARAMETER
Use to access the Video options (page 72).
11 MULTI-ZONE controls
If you’ve made MULTI-ZONE connections (page 35) use these controls to control the sub zone from the main zone
(page 75).
12 SPEAKERS
Use to change the speaker terminal (page 74).
13 iPod iPhone iPad DIRECT CONTROL
Change the receiver’s input to the iPod and enable iPod operations on the iPod (page 48).
14 Listening mode buttons
! AUTO SURR/ALC/STREAM DIRECT – Switches between Auto Surround (page 55), Auto Level Control,
Optimum Surround mode and Stream Direct mode (page 57).
! HOME THX – Press to select a Home THX listening mode (page 56).
! STANDARD SURROUND – Press for Standard decoding and to switch various modes (2 Pro Logic, Neo:X,
Stereo etc.) (page 55).
! ADVANCED SURROUND – Use to switch between the various surround modes (page 56).
15 HOME MENU
Use to access the Home Menu (pages 42, 44, 66, 85 and 93).
16 RETURN
Press to confirm and exit the current menu screen.
17 TUNER controls
! BAND – Switches between AM and FM radio bands (page 51).
! TUNER EDIT – Use with TUNE i/j, PRESET k/l and ENTER to memorize and name stations for recall
(page 51).
18 PHONES jack
Use to connect headphones. When the headphones are connected, there is no sound output from the speakers.
19 MCACC SETUP MIC jack
Use to connect the supplied microphone (page 42).
15
02
20 iPod iPhone iPad USB terminals
Use to connect your Apple iPod/iPhone/iPad as an audio and video source (page 37), or connect a USB device for
audio and photo playback (page 38).
21 HDMI input/MHL connector
Use for connection to a compatible HDMI device (Video camera, etc.) (page 38).
An MHL-compatible mobile device can also be connected here using the included MHL cable (page 38).
Controls and displays
16
Connecting your equipment
Connecting your equipment .........................................................................................................18
Rear panel ......................................................................................................................................18
Determining the speakers’ application ........................................................................................19
Placing the speakers ...................................................................................................................... 21
Connecting the speakers ...............................................................................................................22
Installing your speaker system ..................................................................................................... 23
About the audio connection ......................................................................................................... 27
About the video converter ...........................................................................................................27
About HDMI ................................................................................................................................... 28
Connecting your TV and playback components .........................................................................28
Connecting an HDD/DVD recorder, BD recorder and other video sources ............................... 31
Connecting a satellite/cable receiver or other set-top box ........................................................32
Connecting other audio components .......................................................................................... 33
Connecting additional amplifiers ................................................................................................. 33
Connecting AM/FM antennas .......................................................................................................34
MULTI-ZONE setup ........................................................................................................................35
Connecting to the network through LAN interface ...................................................................37
Connecting optional Bluetooth ADAPTER ...................................................................................37
Connecting an iPod........................................................................................................................37
Connecting a USB device ..............................................................................................................38
Connecting an MHL-compatible device ....................................................................................... 38
Connecting an HDMI-equipped component to the front panel input ...................................... 38
Connecting to a wireless LAN ....................................................................................................... 39
Connecting an IR receiver .............................................................................................................39
Switching components on and off using the 12 volt trigger ..................................................... 39
Plugging in the receiver ................................................................................................................ 40
17
03
Connecting your equipment
Connecting your equipment
This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This chapter
explains the kinds of components you can connect to make up your home theater system.
CAUTION
! Before making or changing the connections, switch off the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
! When making connections, also keep the power cords of the devices being connected unplugged from the
power outlets.
! Depending on the device being connected (amplifier, receiver, etc.), the methods of connection and terminal
names may differ from the explanations in this manual. Also refer to the operating instructions of the respective devices.
Rear panel
DC OUTPUT
(
)
LAN
10/100
OPTICALCOAXIAL
IN
(TV)
F HEIGHT
1
IN
(
DVR/BDR
F WIDE
PRE OUT
B
2
for WIRELESS LAN
)
L
R
RL
(CONTROL)
2
IN
)
SAT/CBL
(Single)
FRONT WIDE /
RL
OUT
(
5 V
0.6 A MAX
OUTPUT
SURROUND
AC IN
)
SURROUND BACK
RLRL
(Single)
ASSIGNABLE
1
IN
(
)
DVD
2
IN
(
DVR/
)
BDR
MONITOR
OUT
RS-232C
EXTENSION
HDMI
ASSIGNABLE
1 - 7
COMPONENT VIDEO
PBY
P
R
ANTENNA
AM LOOP FM UNBAL 75
12V TRIGGER
IR
OUT
IN
(
OUTPUT 5 V
)
150 mA MAX
IN
(
DVD
ZONE 2
OUT
1
2
IN
(
OUTPUT 12 V
TOTAL 150 mA MAX
1
)
OUT
SUBWOOFER
1
2
2
3
BD IN
IN
(
)
SAT/CBL
VIDEO
DVDINZONE 3
SAT/CBL
IN
IN OUT
A A
RL
SPEAKERS
)
4
IN
IN
(
)
(
)
DVR/BDR
VIDEO
MONITOR
VIDEO
OUT
DVR/BDR
IN
AUDIO
FRONTCENTER
IN 6IN
(CD)
1
IN
ASSIGNABLE
ADAPTER PORT
(
OUTPUT 5 V
0.1 A MAX
FRONT
1
CENTER
FRONT HEIGHT
7
)
SUBWOOFER
OUT 2OUT 1
ASSIGNABLEASSIGNABLE
1
IN
(
)
(
DVD
SURROUND SURR BACK
2
Note
! The input functions below are assigned by default to the receiver’s different input terminals. Refer to The Input
Setup menu on page 44 to change the assignments if other connections are used.
Input function
BD
HDMI Audio Component
(BD)
DVD IN 1 COAX-1 IN 1
SAT/CBL IN 2 COAX-2
DVR/BDR IN 3 OPT-2 IN 2
VIDEO IN 4
HDMI 5/MHL
(front panel)
IN 5
HDMI 6 IN 6
HDMI 7 IN 7
TV OPT-1
CD ANALOG-1
Input Terminals
! The CU-RF100 omni-directional remote control (separately sold) can be connected to the RS-232C and
EXTENSION terminals. Using the CU-RF100 lets you display the receiver’s display information on the remote
control display in your hands and operate it without worrying about obstacles or the direction in which the
remote control is pointing.
MONITOR
OUT
12V TRIGGER
OUT
)
1
IN
(
OUTPUT 12 V
TOTAL 150 mA MAX
SUBWOOFER
1
2
IN
2
)
RS-232C
EXTENSION
ANTENNA
AM LOOP FM UNBAL 75
IR
(
OUTPUT 5 V
150 mA MAX
18
03
Connecting your equipment
Determining the speakers’ application
This unit is equipped with speaker terminals for 11 channels, allowing users to select a variety of speaker layouts/
usage patterns according to their tastes. The terminals to which the speakers should be connected differ according to the speaker layout/usage pattern. Select one speaker layout/usage pattern before connecting the speakers.
For instructions on connections, see Installing your speaker system on page 23.
! Be sure to connect speakers to the front left and right channels (L and R).
! It is also possible to only connect one of the surround back speakers (SB) or neither.
! If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.
Important
! The Speaker System setting must be made if you use any of the connections shown below other than [A] (see
Speaker system setting on page 93).
! The speakers from which sound is output can be switched according to the speaker layout/usage pattern
(sound is not necessarily output from all connected speakers). Use the SPEAKERS button to switch the speakers from which sound is output. For details, see Switching the speaker terminals on page 74.
[A] 9.2 channel surround system (Front height/Front wide) connection
*Default setting
! Speaker System setting: 9.1ch FH/FW
FHR
FHL
L
SW 2
FWL
SL
R
FWR
SW
1
C
SBL
SR
SBR
[B] 7.2 channel surround system & Speaker B connection
! Speaker System setting: 7.1ch + Speaker B
FHR
FHL
L
2
SW
SL
With these connections you can simultaneously enjoy 7.2-channel surround sound in the main zone with stereo
playback of the same sound on the B speakers. The same connections also allow for 9.2-channel surround sound
in the main zone when not using the B speakers.
The speakers from which sound is output can be switched using the SPEAKERS button. For details, see Switching
the speaker terminals on page 74.
R
SW 1
C
SBL
SR
SBR
R
L
Speaker B
[C] 7.2 channel surround system & Front Bi-amping connection (High quality
surround)
! Speaker System setting: 7.1ch Front Bi-Amp
Bi-amping connection of the front speakers for high sound quality with 7.2-channel surround sound.
Front Bi-Amp
R
L
SW
SW 1
C
2
SR
A 9.2 ch surround system connects the left and right front speakers (L/R), the center speaker (C), the left and right
front height speakers (FHL/FHR), the left and right front wide speakers (FWL/FWR), the left and right surround
speakers (SL/SR), the left and right surround back speakers (SBL/SBR), and the subwoofers (SW 1/SW 2).
It is not possible to produce sound simultaneously from the front height speakers and the front wide speakers.
This surround system produces a more true-to-life sound from above.
The speakers from which sound is output can be switched using the SPEAKERS button. For details, see Switching
the speaker terminals on page 74.
19
SL
SBR
SBL
03
Connecting your equipment
[D] 7.2 channel surround system (Surround back) & ZONE 2 connection (Multi
Zone)
! Speaker System setting: 7.1ch + ZONE 2
With these connections you can simultaneously enjoy 7.2-channel surround sound in the main zone with stereo
playback on another component in ZONE 2. (The selection of input devices is limited.)
This speaker layout/usage pattern provides 7.2-channel playback using the surround back channels in the main
zone. To achieve 7.2-channel playback using the front height and front wide channels with ZONE 2 connections,
see [E].
Main zone
R
L
SW
SL
SW 1
C
2
SBL
SR
SBR
ZONE 2
Sub zone
R
L
[E] 7.2 channel surround system (Front height/Front wide) & ZONE 2
connection (Multi Zone)
! Speaker System setting: 7.1ch FH/FW + ZONE 2
With these connections you can simultaneously enjoy 7.2-channel surround sound in the main zone with stereo
playback on another component in ZONE 2. (The selection of input devices is limited.)
This speaker layout/usage pattern provides 7.2-channel playback using the front height and front wide channels
in the main zone. To achieve 7.2-channel playback using the surround back channels with ZONE 2 connections,
see [D].
It is not possible to produce sound simultaneously from the front height speakers and the front wide speakers.
The speakers from which sound is output can be switched using the SPEAKERS button. For details, see Switching
the speaker terminals on page 74.
Main zone
FHR
C
SL
SW 1
R
FWR
SR
ZONE 2
Sub zone
R
L
FWL
FHL
L
2
SW
[F] 5.2 channel surround system & Front Bi-amping connection (High quality
surround) & ZONE 2 connection (Multi Zone)
! Speaker System setting: 5.1ch Bi-Amp + ZONE 2
With these connections you can simultaneously enjoy Bi-amping connection of the front speakers for high sound
quality with 5.2-channel surround sound in the main zone with stereo playback on another component in ZONE 2.
(The selection of input devices is limited.)
Front Bi-Amp
R
L
SW
SW 1
C
2
SR
SL
ZONE 2
Sub zone
R
L
[G] 5.2 channel surround system & ZONE 2/ZONE 3 connection (Multi Zone)
! Speaker System setting: 5.1ch + ZONE 2+3
With these connections you can simultaneously enjoy 5.2-channel surround sound in the main zone with stereo
playback on another component in ZONE 2 and ZONE3. (The selection of input devices is limited.)
Main zone Sub zone
R
L
SW 1
C
2
SW
SR
SL
L
ZONE 2
R
ZONE 3
R
L
Other speaker connections
! Your favorite speaker connections can be selected even if you have fewer than 5.2 speakers (except front left/
right speakers).
! When not connecting a subwoofer, connect speakers with low frequency reproduction capabilities to the front
channel. (The subwoofer’s low frequency component is played from the front speakers, so the speakers could
be damaged.)
! After connecting, be sure to conduct the Full Auto MCACC (speaker environment setting) procedure. See
Automatically conducting optimum sound tuning (Full Auto MCACC) on page 42.
20
03
Connecting your equipment
Placing the speakers
Refer to the chart below for placement of the speakers you intend to connect.
2SW 1
FHL
FWL
SL
! Place the surround speakers at 120º from the center. If you, (1) use the surround back speaker, and, (2) don’t
use the front height speakers / front wide speakers, we recommend placing the surround speaker right beside
you.
! If you intend to connect only one surround back speaker, place it directly behind you.
! Place the left and right front height speakers at least one meter (3.3 ft.) directly above the left and right front
speakers.
THX speaker system setup
If you are using a THX certified subwoofer, use the THX INPUT jack on the subwoofer (if your subwoofer has one)
or switch the filter position to THX on your subwoofer.
See also THX Audio Setting on page 95 to make the settings that will give you the best sound experience when
using the Home THX modes (page 56).
SW
C
L
30 30
60
120 120
60
SBL
SB
FHR
R
FWR
60
SR
SBR
! Try not to place the surround speakers farther away from the listening position than the front and center speak-
ers. Doing so can weaken the surround sound effect.
Some tips for improving sound quality
Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines
should help you to get the best sound from your system.
! The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re
listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a
wall is not recommended.
! For the best stereo effect, place the front speakers 2 m to 3 m (6 ft. to 9 ft.) apart, at equal distance from the TV.
! If you’re going to place speakers around your CRT TV, use shielded speakers or place the speakers at a suffi-
cient distance from your CRT TV.
! If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower
angle.
! Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV
screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left
and right speakers.
! It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use
less of an angle for bigger rooms.
! Surround and surround back speakers should be positioned 60 cm to 90 cm (2 ft. to 3 ft.) higher than your
ears and tilted slightly downward. Make sure the speakers don’t face each other. For DVD-Audio, the speakers
should be more directly behind the listener than for home theater playback.
21
03
tF
Connecting your equipment
Connecting the speakers
Each speaker connection on the receiver comprises a positive (+) and negative (–) terminal. Make sure to match
these up with the terminals on the speakers themselves.
This unit supports speakers with a nominal impedance of 4 W to 16 W.
CAUTION
! These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when con-
necting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated
parts.
! Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any
of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.
Bare wire connections
CAUTION
Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk
of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as
earthquakes.
1 Twist exposed wire strands together.
2 Loosen terminal and insert exposed wire.
3 Tighten terminal.
123
10 mm (3/8 in.)
Bi-amping your speakers
Bi-amping is when you connect the high frequency driver and low frequency driver of your speakers to different
amplifiers for better crossover performance. Your speakers must be bi-ampable to do this (having separate terminals for high and low) and the sound improvement will depend on the kind of speakers you’re using.
Front righ
High
Low
SPEAKERS
Bi-amp compatible
speaker
A
FRONT CENTER
RL
A
FRONTCENTER
FRONT HEIGHT
RL
RL
SPEAKERS
Bi-amp compatible
FRONT HEIGHT
RL
speaker
ront left
High
Low
Note
! Please refer to the manual that came with your speakers for details on how to connect the other end of the
speaker cables to your speakers.
! Use an RCA cable to connect the subwoofer. It is not possible to connect using speaker cables.
! If you have two subwoofers, the second subwoofer can be connected to the SUBWOOFER 2 terminal.
Connecting two subwoofers increases the bass sound to achieve more powerful sound reproduction. In this
case, the same sound is output from the two subwoofers.
Banana plug connections
If you want to use speaker cables terminated with banana plugs, screw the speaker terminal fully shut, then plug
the banana plug into the end of the speaker terminal.
CAUTION
! Most speakers with both High and Low terminals have two metal plates that connect the High to the Low
terminals. These must be removed when you are bi-amping the speakers or you could severely damage the
amplifier. See your speaker manual for more information.
! If your speakers have a removable crossover network, make sure you do not remove it for bi-amping. Doing so
may damage your speakers.
22
03
RL
Connecting your equipment
Bi-wiring your speakers
Your speakers can also be bi-wired if they support bi-amping.
! With these connections, the Speaker System setting makes no difference.
CAUTION
! Don’t connect different speakers from the same terminal in this way.
! When bi-wiring as well, heed the cautions for bi-amping shown above.
% To bi-wire a speaker, connect two speaker cords to the speaker terminal on the receiver.
Using a banana plug for the second connection is recommended.
Installing your speaker system
At the very least, front left and right speakers only are necessary. Note that your main surround speakers should
always be connected as a pair, but you can connect just one surround back speaker if you like (it must be connected to the left surround back terminal).
[A] 9.2 channel surround system (Front height/Front wide) connection
! If necessary, select ‘9.1ch FH/FW’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
! When only connecting one surround back speaker, connect it to the SURROUND BACK L (Single) terminals.
Front height leftFront height right
Front leftFront right Center Subwoofer 2Subwoofer 1
(Single)
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
L
R
PRE OUT
SURROUND
RL
LINE LEVEL
INPUT
SUBWOOFER
FRONT
12
A A
FRONT CENTER
RL
CENTER
FRONT HEIGHT
RL
SURROUND SURR BACK
FRONT WIDE /
RL
Front wide leftFront wide right
SURROUND BACK
(Single)
23
SPEAKERS
Surround right
Surround back right Surround back left
Surround left
03
RL
RL
Connecting your equipment
[B] 7.2 channel surround system & Speaker B connection
! Select ‘7.1ch + Speaker B’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
! When only connecting one surround back speaker, connect it to the SURROUND BACK L (Single) terminals.
Front height leftFront height right
Front leftFront right Center Subwoofer 2Subwoofer 1
(Single)
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
L
R
PRE OUT
SURROUND
RL
LINE LEVEL
INPUT
SUBWOOFER
FRONT
12
A A
FRONT CENTER
RL
CENTER
FRONT HEIGHT
RL
SURROUND SURR BACK
FRONT WIDE /
RL
Speaker B- leftSpeaker B- right
SURROUND BACK
(Single)
[C] 7.2 channel surround system & Front Bi-amping connection (High quality
surround)
! Select ‘7.1ch Front Bi-Amp’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
! When only connecting one surround back speaker, connect it to the SURROUND BACK L (Single) terminals.
Bi-amp compatible speaker
Front right
High
LINE LEVEL
Low
A A
FRONTCENTER
RL
SPEAKERS
INPUT
FRONT
FRONT HEIGHT
RL
Center Subwoofer 2Subwoofer 1
SUBWOOFER
12
CENTER
SURROUND SURR BACK
(Single)
FRONT WIDE /
RL
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
PRE OUT
L
R
Bi-amp compatible speaker
Front left
High
Low
SURROUND
RL
SURROUND BACK
(Single)
SPEAKERS
Surround right
Surround back right Surround back left
Surround left
24
Surround right
Surround back right Surround back left
Surround left
03
RL
RL
Connecting your equipment
[D] 7.2 channel surround system (Surround back) & ZONE 2 connection (Multi
Zone)
! Select ‘7.1ch + ZONE 2’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
! When only connecting one surround back speaker, connect it to the SURROUND BACK L (Single) terminals.
Center Subwoofer 2Subwoofer 1
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
L
R
PRE OUT
RL
LINE LEVEL
INPUT
SUBWOOFER
FRONT
12
A A
FRONT CENTER
RL
SPEAKERS
CENTER
FRONT HEIGHT
RL
SURROUND SURR BACK
(Single)
FRONT WIDE /
RL
Front leftFront right
SURROUND
ZONE 2 - leftZONE 2 - right
SURROUND BACK
(Single)
[E] 7.2 channel surround system (Front height/Front wide) & ZONE 2
connection (Multi Zone)
! Select ‘7.1ch FH/FW + ZONE 2’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
Front height leftFront height right
Front leftFront right Center Subwoofer 2Subwoofer 1
(Single)
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
L
R
PRE OUT
SURROUND
RL
SURROUND BACK
LINE LEVEL
INPUT
SUBWOOFER
FRONT
12
A A
FRONT CENTER
RL
CENTER
FRONT HEIGHT
RL
SURROUND SURR BACK
FRONT WIDE /
RL
Front wide leftFront wide right
(Single)
Surround right
Surround back right Surround back left
Surround left
25
SPEAKERS
Surround right
ZONE 2 - right ZONE 2 - left
Surround left
03
RL
RL
Connecting your equipment
[F] 5.2 channel surround system & Front Bi-amping connection (High quality
surround) & ZONE 2 connection (Multi Zone)
! Select ‘5.1ch Bi-Amp + ZONE 2’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
Bi-amp compatible speaker
Front right
High
LINE LEVEL
Low
A A
FRONT CENTER
RL
SPEAKERS
INPUT
FRONT
FRONT HEIGHT
RL
Center Subwoofer 2Subwoofer 1
SUBWOOFER
12
CENTER
SURROUND SURR BACK
(Single)
FRONT WIDE /
RL
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
PRE OUT
L
R
Bi-amp compatible speaker
Front left
High
Low
SURROUND
RL
SURROUND BACK
(Single)
[G] 5.2 channel surround system & ZONE 2/ZONE 3 connection (Multi Zone)
! Select ‘5.1ch + ZONE 2+3’ from the Speaker System menu.
See Speaker system setting on page 93 to do this.
Center Subwoofer 2Subwoofer 1
F HEIGHT
B
LINE LEVEL
INPUT
F WIDE
L
R
PRE OUT
RL
LINE LEVEL
INPUT
SUBWOOFER
FRONT
12
A A
FRONT CENTER
RL
SPEAKERS
CENTER
FRONT HEIGHT
RL
SURROUND SURR BACK
(Single)
FRONT WIDE /
RL
Front leftFront right
SURROUND
ZONE 3 - leftZONE 3 - right
SURROUND BACK
(Single)
Surround right
ZONE 2 - right ZONE 2 - left
Surround left
26
Surround right
ZONE 2 - right ZONE 2 - left
Surround left
03
Connecting your equipment
About the audio connection
Types of cables and terminals
HDMI HD audio
Digital (Coaxial)Conventional digital audio
Digital (Optical)
Sound signal priority
RCA (Analog)
(White/Red)
! With an HDMI cable, video and audio signals can be transferred in high quality over a single cable.
Transferable audio signals
Conventional analog audio
About the video converter
The video converter ensures that all video sources are output through the HDMI OUT terminal.
If the TV is only connected to the receiver’s composite VIDEO MONITOR OUT jacks, all the other video devices
must be connected through composite connections.
If several video components are assigned to the same input function (see The Input Setup menu on page 44), the
converter gives priority to HDMI, component, then composite (in that order).
Terminal for connection
with source device
HDMI IN HDMI OUT
YPBP
COMPONENT
High picture quality
Note
! The only exception is HDMI: since this resolution cannot be downsampled, you must connect your monitor/TV
to the receiver’s HDMI output when connecting this video source.
! If the video signal does not appear on your TV, try adjusting the resolution settings on your component or dis-
play. Note that some components (such as video game units) have resolutions that may not be converted. In
this case, try switching Digital Video Conversion (in Setting the Video options on page 72) OFF.
! The signal input resolutions that can be converted from the component video input for the HDMI output are
480i/576i, 480p/576p, 720p and 1080i. 1080p signals cannot be converted.
! For optimal video performance, THX recommends switching Digital Video Conversion (in Setting the Video
options on page 72) OFF.
R
VIDEO IN
VIDEO IN
Terminal for connection
with TV monitor
YPBP
COMPONENT VIDEO
MONITOR OUT
MONITOR OUT
R
VIDEO
Video signals
can be output
This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property
rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
27
03
Connecting your equipment
About HDMI
The HDMI connection transfers uncompressed digital video, as well as almost every kind of digital audio.
This receiver incorporates High-Definition Multimedia Interface (HDMI®) technology.
This receiver supports the functions described below through HDMI connections.
! Digital transfer of uncompressed video (contents protected by HDCP (1080p/24, 1080p/60, etc.))
! 3D signal transfer
! Deep Color signal transfer
! x.v.Color signal transfer
! ARC (Audio Return Channel)
! 4K signal transfer
— This may not operate properly, depending on the connected equipment.
— 4K 24p, 4K 25p and 4K 30p signals are supported.
— Not supported for the HDMI IN 6 and IN 7 terminals.
! Input of multi-channel linear PCM digital audio signals (192 kHz or less) for up to 8 channels
! Input of the following digital audio formats:
— Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio (Dolby TrueHD, DTS-HD Master Audio, DTS-HD
High Resolution Audio), DVD-Audio, CD, SACD (DSD signal), Video CD, Super VCD
! Synchronized operation with components using the Control with HDMI function (see Control with HDMI func-
tion on page 65)
Note
! An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High
Bandwidth Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a
separate adaptor (DVIdHDMI) to do so. A DVI connection, however, does not support audio signals. Consult
your local audio dealer for more information.
! If you connect a component that is not compatible with HDCP, an HDCP ERROR message is displayed on
the front panel display. Some components that are compatible with HDCP still cause this message to be displayed, but so long as there is no problem with displaying video this is not a malfunction.
! Depending on the component you have connected, using a DVI connection may result in unreliable signal
transfers.
! This receiver supports SACD, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master Audio. To take advantage
of these formats, however, make sure that the component connected to this receiver also supports the corresponding format.
! Use a High Speed HDMI®/TM cable. If an HDMI cable other than a High Speed HDMI®/TM cable is used, it may
not work properly.
! When an HDMI cable with a built-in equalizer is connected, it may not operate properly.
! Signal transfer is only possible when connected to a compatible component.
! HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the
audio may occur when switching between audio formats or beginning playback.
! Turning on/off the device connected to this unit’s HDMI OUT terminal during playback, or disconnecting/con-
necting the HDMI cable during playback, may cause noise or interrupted audio.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing, LLC in the United States and other countries.
Connecting your TV and playback components
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray Disc player (BD), etc.), you can connect it
to this receiver using a commercially available HDMI cable.
If the TV and playback components support the Control with HDMI feature, the convenient Control with HDMI
functions can be used (see Control with HDMI function on page 65).
This connection is required in
HDMI/DVI-compatible
Blu-ray Disc player
HDMI
ASSIGNABLE
1 - 7
1
2
3
4
7
BD IN
IN
IN
IN
IN
HDMI
ASSIGNABLE
1 - 7
IN 6IN
(
)
(
)
(
)
(
)
DVD
SAT/CBL
DVR/BDR
VIDEO
(CD)
1
IN
ASSIGNABLE
OUT 2OUT 1
ASSIGNABLEASSIGNABLE
1
IN
(
DVD
1
IN
(
)
DVD
DC OUTPUT
(
)
LAN
10/100
for WIRELESS LAN
(CONTROL)
(
OUTPUT
5 V
)
0.6 A MAX
OPTICALCOAXIAL
1
2
2
IN
IN
IN
OUT
(TV)
(
)
)
(
)
DVR/BDR
SAT/CBL
Other HDMI/DVIequipped component
2
IN
(
SAT/CBL
)
IN
(
DVR/BDR
BD IN
! When connecting to an HDMI/DVI-compatible monitor using the HDMI OUT 2 terminal, switch the HDMI
output setting to HDMI OUT 2 or HDMI OUT ALL. See Switching the HDMI output on page 76.
! For input components, connections other than HDMI connections are also possible (see Connecting your DVD
player with no HDMI output on page 29).
order to listen to the sound of
the TV over the receiver.
AUDIO OUT
RL
ANALOG
3
4
IN
(
VIDEO
)
IN 6IN
(CD)
1
IN
ASSIGNABLE
)
HDMI/DVI-compatible
monitor
Select one
DIGITAL OUT
COAXIAL OPTICAL
7
OUT 2 OUT 1
ASSIGNABLE ASSIGNABLE
1
IN
(
)
(
DVD
SAT/CBL
(CONTROL)
2
IN
HDMI INHDMI OUT HDMI OUT
DC OUTPUT
(
)
10/100
LAN
for WIRELESS LAN
(
OUTPUT
5 V
)
OPTICALCOAXIAL
1
IN
IN
(TV)
(
)
DVR/BDR
0.6 A MAX
2
OUT
)
“x.v.Color” and are trademarks of Sony Corporation.
28
03
RL
Connecting your equipment
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
— When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 66).
— If you use a coaxial digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal or analog audio input you connected the TV to (see The Input Setup menu on page 44).
Connecting your DVD player with no HDMI output
This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no
HDMI output) to the receiver.
HDMI/DVI-compatible monitor
HDMI IN
1
IN
(
DVD
1 - 7
P
R
ASSIGNABLE
1
IN
(
)
DVD
2
IN
(
DVR/
)
BDR
HDMI
ASSIGNABLE
COMPONENT VIDEO
PBY
Select one
3
DVR/BDR
COMPONENT VIDEO OUT
4
IN
)
(
)
VIDEO
VIDEO OUT
VIDEO
2
IN
(
SAT/CBL
IN
)
(
BD IN
)
DVD
IN
Y
IN 6IN
DVD player, etc.
PR
P
B
7
IN
HDMI
(
DVD
ASSIGNABLE
1 - 7
ASSIGNABLE
COMPONENT VIDEO
PBY
P
R
1
IN
(
)
DVD
2
IN
(
DVR/
)
BDR
1
BD IN
)
DVD
IN
OUT 2 OUT 1
(
2
3
4
IN
IN
IN
(
)
(
)
(
)
SAT/CBL
DVR/BDR
VIDEO
Select one
DIGITAL OUT
OPTICAL
COAXIAL
(
10/100
LAN
(CONTROL)
ASSIGNABLE ASSIGNABLE
1
IN
IN
)
(
DVD
SAT/CBL
7
IN 6IN
OUT 2OUT 1
ASSIGNABLEASSIGNABLE
1
IN
(
)
DVD
OPTICALCOAXIAL
1
2
(CONTROL)
2
IN
(
SAT/CBL
2
IN
IN
(TV)
(
)
DVR/BDR
DC OUTPUT
(
)
10/100
LAN
for WIRELESS LAN
(
OUTPUT
5 V
)
0.6 A MAX
OPTICALCOAXIAL
1
2
IN
IN
OUT
(TV)
(
)
)
DVR/BDR
DC OUTPUT
)
for WIRELESS LAN
)
AUDIO OUT
ANALOG
OUT
(
OUTPUT
5 V
0.6 A MAX
)
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 28).
— When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so
there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on
page 66).
! If you use an optical digital audio cable, you’ll need to tell the receiver which digital input you connected the
player to (see The Input Setup menu on page 44).
29
03
RL
Connecting your equipment
Connecting your TV with no HDMI input
This diagram shows connections of a TV (with no HDMI input) and DVD player (or other playback component) to
the receiver.
Important
! With these connections, the picture is not output to the TV even if the DVD player is connected with an HDMI
cable. Connect the receiver and TV using the same type of video cable as used to connect the receiver and
player.
! Also, when the receiver and TV are connected by anything other than an HDMI cable, the OSD function allow-
ing display of the receiver’s settings, operations, etc., on the TV’s screen cannot be used. In this case, watch
the receiver’s front panel display while performing the various operations and making settings.
DVD player, etc.
TV
COMPONENT VIDEO IN
PR
PB
Y
VIDEO IN
VIDEO
COMPONENT VIDEO OUT
PR
PB
Y
VIDEO OUT
VIDEO
HDMI OUT
Select oneSelect oneSelect one
DIGITAL OUT
OPTICAL
COAXIAL
AUDIO OUT
ANALOG
! In order to listening to HD audio with this receiver, connect an HDMI cable, and use analog video cable for
video signal input.
Depending on the player, it may not be possible to output video signals to both HDMI and other video output
(composite, etc.) simultaneously, and it may be necessary to make video output settings. Please refer to the
operating instructions supplied with your player for more information.
! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(page 28).
! If you use an optical digital audio cable, you’ll need to tell the receiver which digital input you connected the
player to (see The Input Setup menu on page 44).
ASSIGNABLE
IN
(
DVD
IN
(
DVR/
BDR
MONITOR
OUT
1
2
)
COMPONENT VIDEO
)
HDMI
ASSIGNABLE
1 - 7
PBY
DC OUTPUT
(
)
10/100
LAN
2
)
(CONTROL)
ASSIGNABLEASSIGNABLE
1
2
IN
)
(
)
SAT/CBL
for WIRELESS LAN
(
OUTPUT
5 V
)
OPTICALCOAXIAL
1
IN
IN
(TV)
(
DVR/BDR
DC OUTPUT
(
)
10/100
LAN
for WIRELESS LAN
(
OUTPUT
5 V
)
0.6 A MAX
OPTICALCOAXIAL
1
2
IN
IN
OUT
(TV)
(
)
DVR/BDR
0.6 A MAX
2
OUT
)
1
IN
(
)
DVD
R
P
BD IN
DVD
2
3
IN
(
SAT/CBL
4
IN
(
DVR/BDR
IN
)
(
)
VIDEO
MONITOR
OUT
)
IN 6IN
7
OUT 2OUT 1
(CONTROL)
ASSIGNABLE ASSIGNABLE
1
IN
IN
(
)
(
DVD
SAT/CBL
IN
1
2
3
4
7
BD IN
IN
IN
IN
IN
IN 6IN
HDMI
(
)
DVD
ASSIGNABLE
1 - 7
ASSIGNABLE
COMPONENT VIDEO
PBY
P
R
1
IN
(
)
DVD
2
IN
(
DVR/
DVD
)
BDR
IN
MONITOR
OUT
OUT 2OUT 1
(
)
(
)
(
)
SAT/CBL
DVR/BDR
VIDEO
MONITOR
IN
OUT
(
DVD
30
Loading...