Pioneer DV-510K-S, DV-410VS, DV-410VK, DV-310S, DV-310K Owners Manual

...

DVD Player

DV-510K-S DV-410V-S DV-410V-K DV-310-S DV-310-K DV-210K-K

Operating Instructions

Thank you for buying this Pioneer product.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_En-A

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

D3-4-2-1-3_B_En

WARNING

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V or 120 V) written on the rear panel.

D3-4-2-1-4_A_En

Before plugging in for the first time, read the following

section carefully.

Operating Environment

Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c_A_En

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.

CAUTION

This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the

CLASS 1 LASER PRODUCT

product. Refer all servicing to qualified personnel. The following caution label appears on your unit. Location: inside of the unit

Singapore and Taiwanese model only

D3-4-2-1-8_B_En

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A_En

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_En

CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the

unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

D8-10-3a_En

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

D8-10-2_En

CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION : THE USE OF OPTICAL INSTRUMENTS WITH THIS PRODUCT WILL INCREASE EYE HAZARD.

D6-8-2-1_En

If the AC plug of this unit does not match the AC

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

S002_En

For Australia Model

For Taiwan exclusively

Taiwanese two pin flat-bladed plug

K056 En

outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

CAUTION

The  STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

D3-4-2-2-1a_A_En

D3-4-2-2-2a_A_En

K041_En

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

This product includes FontAvenue® fonts licenced by NEC Corporation. FontAvenue is a registered trademark of NEC Corporation.

Contents

01 Before you start

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

What’s in the box. . . . . . . . . . . . . . . . . . . . . 5

Hints on installation . . . . . . . . . . . . . . . . . . 6

Disc/content format playback

compatibility . . . . . . . . . . . . . . . . . . . . . . . . 6

02 Connections

Easy connections. . . . . . . . . . . . . . . . . . . . 10

Connecting using the S-Video output . . . . 11

Connecting using the component video

output . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting to an AV receiver. . . . . . . . . . . 12

Connecting using HDMI . . . . . . . . . . . . . . 13

03 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . 15

Remote control . . . . . . . . . . . . . . . . . . . . . 16

04 Getting started

Switching on . . . . . . . . . . . . . . . . . . . . . . . 17

Using the on-screen displays. . . . . . . . . . . 17

Setting up the player for your TV . . . . . . . . 18

Setting the language of this player’s on-screen

displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Playing discs . . . . . . . . . . . . . . . . . . . . . . . 19

Singing Your Favorite Songs Along with

Karaoke Discs . . . . . . . . . . . . . . . . . . . . . . 22

05 Playing discs

Scanning discs . . . . . . . . . . . . . . . . . . . . . 24

Playing in slow motion. . . . . . . . . . . . . . . . 24

Frame advance/frame reverse . . . . . . . . . . 25

Viewing a JPEG slideshow . . . . . . . . . . . . . 25

Browsing Discs with the

Disc Navigator. . . . . . . . . . . . . . . . . . . . . . 26

Browsing Files with the

Disc Navigator. . . . . . . . . . . . . . . . . . . . . . 26

Looping a section of a disc . . . . . . . . . . . . 27

Using repeat play. . . . . . . . . . . . . . . . . . . . 28

Using random play . . . . . . . . . . . . . . . . . . 28

Creating a program list . . . . . . . . . . . . . . . 29

Searching a disc . . . . . . . . . . . . . . . . . . . . 30

Switching subtitles . . . . . . . . . . . . . . . . . . 30

Switching audio language/channels . . . . . 31

Zooming the screen. . . . . . . . . . . . . . . . . . 31

Switching camera angles . . . . . . . . . . . . . .31

Displaying disc information . . . . . . . . . . . .31

06 USB playback

Using the USB interface . . . . . . . . . . . . . . .32

07 Audio Settings and Video Adjust menus

Audio Settings menu . . . . . . . . . . . . . . . . .33

Video Adjust menu . . . . . . . . . . . . . . . . . . .34

08 Initial Settings menu

Using the Initial Settings menu. . . . . . . . . .35

Digital Audio Out settings. . . . . . . . . . . . . .35

Video Output settings . . . . . . . . . . . . . . . . .36

Language settings . . . . . . . . . . . . . . . . . . .37

Display settings . . . . . . . . . . . . . . . . . . . . .38

Options settings . . . . . . . . . . . . . . . . . . . . .38

Parental Lock . . . . . . . . . . . . . . . . . . . . . . .39

DTS Downmix . . . . . . . . . . . . . . . . . . . . . . .40

About DivX® VOD content . . . . . . . . . . . . .40

About the HDMI audio output settings . . . .41

09 Additional information

Taking care of your player and discs . . . . . .42

Screen sizes and disc formats . . . . . . . . . .43

Setting the TV system . . . . . . . . . . . . . . . . .44

Resetting the player . . . . . . . . . . . . . . . . . .44

DVD-Video regions . . . . . . . . . . . . . . . . . . .44

Selecting languages using the language code

list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Troubleshooting . . . . . . . . . . . . . . . . . . . . .45

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Language code list . . . . . . . . . . . . . . . . . . .50

Country/Area code list . . . . . . . . . . . . . . . .50

Specifications . . . . . . . . . . . . . . . . . . . . . . .51

Chapter 1

Before you start

Features

• PureCinema Progressive Scan video

When connected to a progressive scan-compatible TV or monitor using the component video outputs, you can enjoy extremely stable, flicker free images, with the same frame refresh rate as the original movie.

• 24-bit/96 kHz compatible DAC

The integrated 24-bit/96 kHz DAC means that this player is compatible with high sampling-rate discs, capable of delivering exceptional sound quality in terms of dynamic range, low-level resolution and high-frequency detail.

What’s in the box

Please confirm that the following accessories are in the box when you open it.

• Remote control

• AA/R6P dry cell batteries x 2

• Audio/video cable (red/white/yellow plugs)

• Power cable (Central American, South American and Taiwan model x2)

• Operating instructions x 2 (Australian, Thailand and PX model x 1)

• Front panel button names sticker (Taiwan models only) – Chinese language button names for the front panel controls.

• Remote control overlay (Taiwan models only) – Place the overlay on the remote control to be able to read the buttons in Chinese.

Putting the batteries in the remote

• Open the battery compartment cover and insert the batteries as shown.

Use two AA/R6P batteries and follow the indications (, ) inside the compartment. Close the cover when you’re finished.

When closing the cover, align the notch and tab, and slide in the direction indicated by the arrow .

Important

Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:

• Don’t mix new and old batteries together.

• Don’t use different kinds of battery together — although they may look similar, different batteries may have different voltages.

• Make sure that the plus and minus ends of each battery match the indications in the battery compartment.

• Remove batteries from equipment that isn’t going to be used for a month or more.

• When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country/area.

• Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.

Hints on installation

DVD-Video DVD-R DVD-RW

Video CDAudio CD CD-R CD-RW

Fujicolor CD

Super VCD

We want you to enjoy using this product for years to come, so please use the following guidelines when choosing a suitable location:

Do...

• Use in a well-ventilated room.

• Place on a solid, flat, level surface, such as a table, shelf or stereo rack.

Don’t...

• Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances.

• Place on a window sill or a place where the player will be exposed to direct sunlight.

• Use in an excessively dusty or damp environment.

• Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.

• Use near a television or monitor as you may experience interference — especially if the television uses an indoor antenna.

• Use in a kitchen or other room where the player may be exposed to smoke or steam.

• Use on a thick rug or carpet, or cover with cloth — this may prevent proper cooling of the unit.

• Place on an unstable surface, or one that is not large enough to support all four of the unit’s feet.

Disc/content format playback compatibility

This player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format — see below for further compatibility information.

Please also note that recordable discs cannot be recorded using this player.

• This unit will play DVD+R/+RW discs.

• is a trademark of DVD Format/Logo

Licensing Corporation.

• is a trademark of FUJIFILM Corporation.

• Also compatible with KODAK Picture CD.

This player supports the IEC’s Super VCD standard. Compared to the Video CD standard, Super VCD offers superior picture quality, and allows two stereo soundtracks to be recorded. Super VCD also supports the widescreen size.

About DualDisc playback

A DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material.

The non-DVD, audio side of the disc is not compliant with the CD audio specification and therefore may not play.

The DVD side of a DualDisc plays in this product. For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

CD-R/-RW compatibility

•Compatible formats: CD audio, Video CD/ Super VCD, ISO 9660 CD-ROM* containing MP3, WMA, MPEG-4 AAC, JPEG or DivX video/WMV files * ISO 9660 Level 1 or 2 compliant. CD

physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible with this player.

• Multi-session playback: No

• Unfinalized disc playback: No

• File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder

DVD+R/+RW compatibility

Only DVD+R/DVD+RW discs recorded in ‘Video Mode (DVD Video Mode)’ which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately.

DVD-R/-RW compatibility

• Compatible formats: DVD-Video, Video Recording (VR)* * Edit points may not play exactly as edited;

screen may go momentarily blank at edited points.

• Unfinalized playback: No

• MP3/WMA/MPEG-4 AAC/JPEG or DivX video/WMV file playback on DVD-R/

-RW: Yes

Compressed audio compatibility

• Compatible formats: MPEG-1 Audio Layer 3 (MP3), Windows Media Audio (WMA), MPEG-4 AAC

• Sampling rates: 32 kHz, 44.1 kHz or 48 kHz

• Bit-rates: Any (128 kbps or higher recommended)

• VBR (Variable Bit Rate) MP3/WMA/ MPEG-4 AAC playback: No

• WMA lossless encoding compatible: No

• DRM (Digital Rights Management) compatible: No (DRM-protected audio files will not play in this player — see also DRM in the Glossary on page 49)

• File extensions: .mp3, .wma, .m4a (these must be used for the player to recognize MP3, WMA and MPEG-4 AAC files — do not use for other file types)

About MPEG-4 AAC

Advanced Audio Coding (AAC) is at the core of the MPEG-4 AAC standard, which incorporates MPEG-2 AAC, forming the basis of the MPEG-4 audio compression technology. The file format and extension used depend on the application used to encode the AAC file. This unit plays back AAC files encoded by

iTunes

bearing the extension ‘.m4a’. DRM-protected files will not play, and files encoded with some versions of iTunes not play, or filenames may display incorrectly.

• Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries.

WMA Windows Media™ Audio (WMA) compatibility

This player can playback Windows Media Audio content. WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media Player for Windows XP, Windows Media Player 9 or Windows Media Player 10 series.

• Windows Media is a trademark of Microsoft Corporation.

• This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

About DivX video

DivX is a digital video format created by DivX, Inc. This player can play DivX videos recorded on DVDs, CDs, or USB storage devices. Keeping the same terminology as DVD-Video, individual DivX video files are called “Titles”. DivX videos will be played in alphabetical order.

may

Displaying external subtitle files

The font sets listed below are available for external subtitle files. You can see the proper font set on-screen by setting the Subtitle Language (in Language settings on page 37) to match the subtitle file.

This player supports the following language groups:

Group 1 Albanian (sq), Basque (eu), Catalan

Group 2

Group 3 Bulgarian (bg), Byelorussian (be),

Group 4 Hebrew (iw), Yiddish (ji)

Group 5 Turkish (tr)

(ca), Danish (da), Dutch (nl), English (en), Faroese (fo), Finnish (fi), French (fr), German (de), Icelandic (is), Irish (ga), Italian (it), Norwegian (no), Portuguese (pt), Rhaeto-Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv)

Albanian (sq), Croatian (hr), Czech (cs), Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk), Slovenian (sl)

Macedonian (mk), Russian (ru), Serbian (sr), Ukrainian (uk)

• Some external subtitle files may be displayed incorrectly or not at all.

• For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi

• The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file.

• The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10.

• DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

DivX video compatibility

• Official DivX® Certified product.

• Plays all versions of DivX

DivX

6) with standard playback of DivX®

media files.

• File extensions: .avi and .divx (these must be used for the player to recognize DivX video files). Note that all files with the

.avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player.

video (including

About Windows Media Video (WMV)

(DV-410V only)

WMV is an acronym for Windows Media Video and refers to a video compression technology developed by Microsoft Corporation. WMV conten can be encoded by using Windows Media

Encoder.

• This player is compatible with WMV9 files that are encoded by using the Windows Media

Encoder 9 Series, with .wmv as an

extension.

• Compatible with size under 720x576 pixels/ 720x480 pixels.

• Advanced Profile is not supported.

• DRM-protected video files will not play in this player.

PC-created disc compatibility

Discs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information. Discs recorded in packet write mode (UDF format) are not compatible with this player. Check the DVD-R/-RW or CD-R/-RW software disc boxes for additional compatibility information.

JPEG file compatibility

•Compatible formats: Baseline JPEG and EXIF 2.2* still image files up to a resolution of 3072 x 2048. *File format used by digital still cameras.

• Progressive JPEG compatible: No

• File extensions: .jpg (must be used for the player to recognize JPEG files — do not use for other file types)

Chapter 2

Connections

Easy connections

Important

• Before making or changing any connections, switch off the power and disconnect the power cable from the AC outlet.

• The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In this setup, stereo audio is played through the speakers in your TV.

• This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using audio/video cables, as the picture from this player will not appear properly on your TV. (This player may also not be compatible with some combination TV/VCRs for the same reason; refer to the manufacturer for more information.)

To audio/video inputs

AUDIO OUT

White

HDMI OUT

DV-410V

PRPBY COMPONENT VDEO OUT

V DEO OUT

DIGITAL

AUDIO OUT

COAXAL

OPTICAL

Yellow

1 Connect the AUDIO OUT L/R

VIDEO OUT

and

jacks to a set of A/V inputs

on your TV.

Use the supplied audio/video cable, connecting the red and white plugs to the audio outputs and the yellow plug to the video output. Make sure you match up the left and right audio outputs with their corresponding inputs for correct stereo sound.

See below if you want to use a component or S-Video cable for the video connection.

Red

To power outlet

2 Connect the supplied AC power cable to the AC IN inlet, then plug into a power outlet.

Note

• Before unplugging the player from the power outlet, make sure you first switch it into standby using either the front panel

 STANDBY/ON

control, and wait of the

button, or the remote

-OFF- message to

disappear from the player’s display.

• For the above reasons, do not plug this player into a switched power supply found on some amplifiers and AV receivers.

AC IN

Connecting using the S-Video

OMPONENT VDEO OU

VDEO OU

-VDEO OU

DGI AL

AU IO OUT

UDIO OU

HDMI OU

COAXAL

OPTICA

To S-Video input

DV-410V

COMPO IDEO O

VIDEO OUT

DIGTAL

AUDIO OUT

AUDO OUT

HDMI OUT

OAXAL

OPTICAL

To component video input

DV-410V

output

Connecting using the component video output

(except for DV-210K)

If your TV (or other equipment) has an S-Video (S1) input, you can use the S-Video output on this player instead of the standard (composite) output for a better quality picture.

• Use an S-Video cable (not supplied) to connect the S-VIDEO OUT to an S-Video input on your TV (or monitor or AV receiver).

Line up the small triangle above the jack with the same mark on the plug before plugging in.

You can use the component video output instead of the standard video out jack to connect this player to your TV (or other equipment). This should give you the best quality picture from the three types of video output available.

• Use a component video cable (not supplied) to connect the COMPONENT VIDEO OUT jacks to a component video input on your TV, monitor or AV receiver.

Watching progressive scan video from the component video outputs

This player can output progressive scan video from the component video output. Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flicker-free image.

To set up the player for use with a progressive scan TV, see Video Output settings on page 36. When the player is set to output progressive scan video, the front panel display.

PRGSVE indicator lights in the

HDMI

STANDB /ON

COMPONENT VDEO OUT

VDEO OUT

VIDEO OUT

DIGI AL

AUDIO OUT

AUDO OUT

HDMI OUT

COAXAL

OPTCAL

DV-410V

AV receiver

To audio/video inputs

Important

• If you connect a TV that is not compatible with a progressive scan signal and switch the player to progressive, you will not be able to see any picture at all. In this case, switch everything off and reconnect using the supplied video cable (see Easy connections on page 10), then switch back to

Interlace (see below).

Switching the video output to interlace using the front panel controls

Switch the player to standby then, using the front panel controls, press  STANDBY/ON while pressing  to switch the player back to

Interlace.

• If the player is connected using HDMI, disconnect the HDMI cable before resetting the player to interlace output. (If left connected, the HDMI output resolution will be reset to its default — see

Resetting the output resolution to the default setting with HDMI connection on

page 14.)

 STANDBY/ON

DV-410V



Connecting to an AV receiver

You can connect this player to your AV receiver using one of the digital outputs. In addition to these connections, you should also connect the analog outputs for compatibility with all discs. You’ll probably also want to connect a video output to your AV receiver. You can use any of the video outputs available on this player (the illustration shows a standard (composite) connection).

1 Connect the analog AUDIO OUT L/R and VIDEO OUT jacks on this player to a set of analog audio and video inputs on your AV receiver.

2 Connect the AV receiver’s video output to a video input on your TV.

You can also use the S-Video or component video jacks to connect to the AV receiver if you prefer.

Tip

• You usually have to connect the same kind of video cable between your DVD player and AV receiver, and between your AV receiver and TV.

Connecting the digital output

COMPONENT VIDEO OUT

VIDEO OU

SV DEO OUT

DIGI AL

AUDIO OU

AUDO OUT

HDMI OUT

COAXAL

OPTCAL

PRY OMPONENT VDEO OU

ID O O T

SVI EO OUT

DGI AL

AUDO OUT

UDIO OU

H M OUT

OAXAL

OP ICA

DV-410V

HDMI-compatible display

To HDMI interconnect

This player has both optical (except for DV-210K) and coaxial-type digital audio

outputs for connection to an AV receiver. Connect whichever is convenient.

Depending on the capabilities of your AV receiver, you might have to set up this player to output only digital audio in a compatible format. See Digital Audio Out settings on page 35 and refer to the operating instructions that came with your AV receiver.

• Connect one of the DIGITAL AUDIO OUT jacks on this player to a digital input on your AV receiver.

To coaxial/optical digital input

AV receiver

DV-410V

For a coaxial connection, use a coaxial cable (similar to the supplied video cable) to connect the COAXIAL DIGITAL AUDIO OUT jack to a coaxial input on your AV receiver.

Except for DV-210K: For an optical connection, use an optical cable (not supplied) to connect the OPTICAL DIGITAL AUDIO OUT jack to an optical input on your AV receiver.

Connecting using HDMI

(DV-410V only)

If you have a HDMI equipped monitor or display, you can connect it to this player using a commercially available HDMI cable.

The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible with, including DVD-Video, Video CD/Super VCD, CD, WMA, MP3, MPEG-4 AAC, DivX video and WMV.

• Use an HDMI cable (not supplied) to connect the HDMI OUT interconnect on this player to an HDMI interconnect on a HDMI-compatible display.

The arrow on the cable connector body should be face up for correct alignment with the connector on the player.

Note

• This unit has been designed to be compliant with HDMI (High-Definition Multimedia Interface). Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.

• When you change the component

HDMI

STANDBYON

DV-410V

 STANDBY/ON



connected to the HDMI output, you will also need to change the HDMI settings to match the new component (see HDMI Out on page 35, HDMI Resolution and HDMI Color on page 37 to do this). However, the settings for each component are then stored in memory (for up to 2 components).

• The HDMI connection is compatible with

44.1 kHz/48 kHz/96 kHz, 16 bit/20 bit/24 bit 2 channel linear PCM signals, as well as Dolby Digital, DTS and MPEG audio bitstream.

– Manufactured under license from Dolby

Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

About HDMI

HDMI (High-Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD players, DTV, set-top boxes, and other AV devices. HDMI was developed to provide the technologies of High-bandwidth Digital Content Protection (HDCP) as well as Digital Visual Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by DVI-compliant displays. HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to five gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.

– Manufactured under license under U.S.

Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS 2.0 + Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.

Patent #: 5,451,942 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Out are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved.

• HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Resetting the output resolution to the default setting with HDMI connection

Switch the player to standby then, using the front panel controls, press  STANDBY/ON while pressing  to switch the player back to 720x480p (NTSC)/720x576p (PAL).

Chapter 3

Controls and displays

Front panel

STANDBY/ON

HDMI

DV-410V

MC1 MIC2

STANDBY/ON

VOLUME

MAX

MIN

DV-510K

1  STANDBY/ON (page 17)

2 Disc tray 3  OPEN/CLOSE (page 19)

4Display 5TOP MENU (page 21) 6 ENTER & cursor buttons (page 17) 7MENU (page 21) 8 RETURN (page 17) 9HOMEMENU (page 17) 10 USB port (Type A) (except for DV-210K)

(page 32)

 OPENCLOSE

USB

DVD/USB

1012 1116 131415

 OPEN/CLOSE

USB

DVD/USB

1012 1117 13141518

53 4 6 71

TOP MENU MENU

ENTER

HOME MENU

9 8

53 4 6 71

TOP MENU

ENTER

HOME MENU

9 8

RETURN

11 DVD/USB (except for DV-210K) (page 32) 12  (page 20) 13  (page 20) 14  (page 20) 15  and  (page 20) 16 HDMI indicator (DV-410V only)

Lights when this player is recognized by another HDMl or DVI/HDCP compatible component.

17 VOLUME control (DV-510K/DV-210K only)

(page 22)

18 MIC 1/MIC2 input jacks (DV-510K/ DV-210K only) (page 22)

Remote control

STANDBY/ON

OPEN/CLOSE

AUDIO

SUBTITLE

ANGLE

CLEAR

USB

DVD/

TOP MENU

ENTER

RETURN

PLAY MODESURROUND

ZOOM

DISPLAY

PLAY

PAUSE

DVD

STOP NEXT

HOME MENU

12 13

11 22

1  STANDBY/ON (page 17) 2 AUDIO (page 31) 3 SUBTITLE (page 30) 4 Number buttons (page 20) 5TOP MENU (page 21)

DV-410V/DV-310

TOP MENU

ECHO

HOME MENU

KARAOKE

DV-510K/DV-210K

KEY

ENTER

RETURN

KEY

PLAY

STOP NEXT

PAUSE

DISPLAY

ZOOM

PLAY MODE

6 ENTER & cursor buttons (page 17)

KEY (high)/KEY (low) (for DV-510K/

DV-210K) (page 22)

ECHO +/- (for DV-510K/DV-210K) (page 22)

7HOMEMENU (page 17) 8  and / (pages 20 and 24) 9  PLAY (page 20) 10  PREV (page 20) 11  PAUSE (page 20) 12 SURROUND (page 33)

KARAOKE (for DV-510K/DV-210K)

(page 22)

13 PLAY MODE (page 27) 14  OPEN/CLOSE (page 19) 15 ANGLE (page 31) 16 DVD/USB (page 32)

ENTER (for DV-210K) (page 17)

17 CLEAR (page 29) 18 MENU (page 21) 19 RETURN (page 17) 20  and / (pages 20 and 24) 21  NEXT (page 20) 22  STOP (page 20) 23 DISPLAY (page 31) 24 ZOOM (page 31)

ECHO

Using the remote control

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote and the remote sensor on the unit.

• The remote has a range of about 7 m.

• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit’s remote sensor.

• Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit.

• Replace the batteries when you notice a fall off in the operating range of the remote.

+ 36 hidden pages