Pioneer DDJWeGO2 User Manual

“djay 2/vjay for iPad/iPhone”

Audio Setup Guide

Before start (Important)

・You can buy ”djay 2 for iPad/iPhone”、”vjay for iPad/iPhone” at App

Store.

・For the customers who already have ”djay 2 for iPad/iPhone”,

”vjay for iPad/iPhone”, please update it to the latest version.

・Please ensure that the firmware of your DJ controller is updated to

the latest version. You can download it from the URL below. http://pioneerdj.com/support/ ・In order to connect and operate DDJ-WeGO2 and iPad/iPhone,

you need a USB power adaptor and a USB mobile battery, both of

which can be purchased separately, as well as the cable ex-

clusively for use with the controller, which is included with it

(Lightning).

Please see the Operating Instruction of DDJ-WeGO2 for details. ・Please see the separately prepared “Hardware Diagram” for the

functions controllable with DDJ-WeGO2.

Note: ・”djay 2 for iPad/iPhone” and ”vjay for iPad/iPhone” are products

of Algoriddim. Please access the following URL to obtain the manual of them. http://www.algoriddim.com/djay-ipad http://www.algoriddim.com/vjay-ipad

・”djay LE for iPad/iPhone” cannot be controlled by DDJ-WeGO2.

Minimum operating environment

These are the minimum requirements to run the combination of the application and DDJ-WeGO2. Please visit App Store for the minimum operating environment of the application itself.

Check the audio device setup

When the application is launched, an audio engine is automatically configured to output the audio from Master and Monitor of DDJ- WeGO2. Please make sure that the audio device is properly set up. ― Figures show an example of “djay 2 for iPad.”

1. Tap

2. Ensure that the name of the DJ controller connected to the application is displayed and the following channels are ticked.

・

Main Output : Ch 1-2 / PIONEER DDJ- WeGO2 Audio Out

・

Pre-Cueing : Ch 3-4 / PIONEER DDJ- WeGO2 Audio Out

to launch [Audio Device Setup].

iDevice

iOS iOS6

djay２

for iPad

iPad(４th generation ),

iPad mini

vjay

for iPad

djay 2

for iPhone

iPhone 5,

iPod touch(5th generation)

vjay

for iPhone

Note:

・The above operation is not guaranteed on all iPad/iPhone, even if all the

required operating environment conditions indicated here are fulfilled.

・Depending on the power saving or other settings of iPad/iPhone, the

device may not fulfill its potential.

・Note that problems may arise with the functionality depending on other

software running on your iPad/iPhone.

Steps to launch the devices

Please follow the Operating Instruction of DDJ-WeGO2 to connect DDJ-WeGO2 and iPad or iPhone using the cable exclusively for use with this controller (Lightning). Then, connect a USB power adaptor and a USB mobile battery, both of which can be purchased separately, and launch the controller in the following steps.

1. Turn the power of DDJ-WeGO2.

― If the power has already been turned on, please turn off the power and then turn it on again.

2. Turn the power of an iPad/iPhone.

3. Launch djay 2 for iPad or vjay for iPad.

Note: ・If djay 2 for iPad/iPhone or vjay for iPad/iPhone cannot be

controlled by DDJ-WeGO2, please remove the iPhone/iPad connection cable from your iPad, iPhone or iPod touch and connect it again.

・If ticks are not shown, tap the appropriate options. ・If the name of the DJ controller is not displayed, please ensure

that the power of the DJ controller is turned on and try plugging the iPhone/iPad cable (Lightning) in and out of the jack of iPhone or iPad for several times.

About trademarks and registered trademarks

・Pioneer is a registered trademark of PIONEER CORPORATION. ・App Store, iPad, iPod, iPod touch and iPhone are trademarks of Apple Inc.,

registered in the U.S. and other countries.

・iOS is a trademark on which Cisco holds the trademark right in the US and

certain other countries.