Pioneer AVH-P7950DVD User Manual

English

Deutsch

Français

Italiano

Nederlands

PyТТНЛИ

AVH-P7950DVD

INSTALLATION MANUAL

This product conforms to new cord colors.

Contents

Connecting the Units ................................ 1

Connecting the system ...................................... 3

Connecting the power cord (1) .......................... 5

Connecting the power cord (2) .......................... 7

When connecting to separately sold power

amp ............................................................ 9

When connecting with a rear view camera .... 11

When connecting the external video

component and the display ...................... 13

Installation ................................................ 15

Installing the hide-away unit .......................... 16

DIN Front/Rear-mount .................................... 16

DIN Front-mount ............................................ 16

DIN Rear-mount .............................................. 17

Installing the remote control unit .................... 18

WARNING:

• To avoid the risk of accident and the potential violation of applicable laws, the front DVD or TV (sold separately) feature should never be used while the vehicle is being driven. Also, Rear Displays should not be in a location where it is a visible distraction to the driver.

• In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and this unit’s DVD features should not be used.

• If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly.

CAUTION:

• PIONEER does not recommend that you install or service your display yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to authorized Pioneer service personnel.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed.

• Do not drill a hole into the engine compartment to connect the yellow lead of the unit to the vehicle battery. Engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. Take extra care in securing the wire at this point.

• It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift. Be sure to install the display in such a way that it will not obstruct driving.

• Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, parking brake or seat sliding mechanism.

• Do not shorten any leads. If you do, the protection circuit may fail to work properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Connecting the Units

English

Español

Deutsch

Français

Italiano

Nederlands

PyТТНЛИ

Note:

• Use this unit in other than the following conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4

ohm to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a battery.

— Cover any disconnected cable connectors

with insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable direct-

ly to ground. — Never band together multiple speaker’s nega-

tive cables.

• Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

• Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

• Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result.

• IP-BUS connectors are color-coded. Be sure to connect connectors of the same color.

• This unit cannot be installed in a vehicle without ACC (accessory) position on the ignition switch.

Fig. 1

• Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached.

• Cord function may differ according to the product, even if cord color is the same. When connecting this system, be sure to check all manuals and connect cords correctly.

No ACC positionACC position

Connecting the Units

Connecting the system

Blue

Violet

6 m

Hide-away unit (supplied)

Black

STAND ALONEIP BUS

25 pin cable (supplied with XDV-P650) Depending on where you install, this cable is not used.

Black

AV-BUS cable (supplied with XDV-P650)

Black

IP-BUS input (Blue)

AV-BUS cable (supplied with TV tuner)

Blue

Antenna jack

Antenna cable (supplied)

6 m

AV-BUS input (Blue)

IP-BUS cable (supplied with XDV-P650)

Blue

Hide-away unit (supplied with XDV-P650)

XDV-P650 (sold separately)

English

Español

Deutsch

Français

Italiano

Nederlands

PyТТНЛИ

Fig. 2

Black

Blue

Black

Violet

Blue

40 cm

15 cm

40 cm

1 m

This product

Power supply box (supplied)

Blue

IP-BUS cable

Multi-CD player (sold separately)

Hide-away TV tuner (e.g. GEX-P5750TV(P)) (sold separately)

IP-BUS cable (supplied with TV tuner)

Microphone/auxiliary input jack (3.5 ø) (MIC/AUX IN)

1.5 m

30-pin cable (supplied)

Optical cable (e.g. CD-AD600) (sold separately)

Before installing this unit to your vehicle, pull out the jack to the place where you can easily plug in/out the microphone or stereo mini plug cable. Use a stereo mini plug cable to connect with auxiliary equipment.

Connecting the Units

Connecting the power cord (1)

If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly.

Yellow After making all other connections to this unit, connect this to the positive + terminal of the battery.

CAUTION

Attach a 20 A fuse immediately prior to the battery. Also, use heat resistant battery cable with more than 5 mm2 sectional area.

Black (chassis ground) Connect to a clean, paint-free metal location.

Red Connect to terminal controlled by ignition switch (12 V DC).

Orange/white Connect to lighting switch terminal.

English

Español

Deutsch

Français

Italiano

Nederlands

PyТТНЛИ

Fig. 3

Fuse resistor

Fuse (7.5 A)

This product

Power supply box (supplied)

Yellow/black If you use equipment with Mute function, wire this lead to the Audio Mute lead on that piece of equipment. If not, keep the Audio Mute lead free of any connections.

Connecting the Units

Connecting the power cord (2)

If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly.

Front speaker (MID/FRONT OUTPUT)

Rear speaker

Front speaker (MID/FRONT OUTPUT)

Rear speaker

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

Hide-away unit (supplied)

≠

Left Right

Tweeter (FRONT HIGH OUTPUT)

Front center speaker (FRONT CENTER OUTPUT)

Rear center speaker (REAR CENTER OUTPUT)

Tweeter (FRONT HIGH OUTPUT)

White

White/black

Gray

Gray/black

Black/white

Black

Black/white

Black

Connect when the audio settings of this product are used in the network mode.

English

Español

Deutsch

Français

Italiano

Nederlands

PyТТНЛИ

Fig. 4

WARNING

Violet/white

See the section “When connecting with a rear view camera”.

Note:

• The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer.

Connection method

1. Clamp the lead. 2. Clamp firmly with needle-nosed pliers.

Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch.

Power supply side

Ground side

Black (chassis ground) Connect to a clean, paint-free metal location.

Fuse (10 A)

Parking brake switch

Fuse (4 A)

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

Yellow After making all other connections to this unit, connect this to the positive + terminal of the battery.

CAUTION

Attach a 20 A fuse immediately prior to the battery. Also, use heat resistant battery cable with more than 5 mm2 sectional area.

When connecting to separately sold power amp

Connecting the Units

Hide-away unit (supplied)

System remote control

Connect when the audio settings of this product are used in the network mode.

See the section “Connecting the power cord (2)”.

Blue/white

Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

English

Español

Deutsch

Français

Italiano

Nederlands

PyТТНЛИ

Fig. 5

Power amp (sold separately)

RCA cables (sold separately)

Subwoofer

Front middle range speaker

Rear speaker

Rear center speaker

Left Right

Power amp (sold separately)

Front middle range speaker

Rear speaker

Tweeter

Front center speaker

Tweeter

Connecting the Units

When connecting with a rear view camera

When using this product with a rear view camera, automatic switching to video from a rear view camera when the gear shift is moved to REVERSE (R) position is possible.

WARNING:

• USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.

CAUTION:

• The screen image may appear reversed.

• The rear view camera function is to be used as an aid for backing into a tight parking spot. Do not use this function for entertainment purposes.

• Objects in the rear view may appear closer or more distant than they actually are.

+ 26 hidden pages