Pioneer AVH-P6850DVD Installation Manual

English

ENG/MASTER COVER 98 INST

AVH-P6850DVD

This product conforms to new cord colors.

INSTALLATION MANUAL

INSTALLATION MANUAL

<CRD4072-A> 1

1

Contents

Connecting the Units ................................ 1

Connecting the power cord .............................. 3

When connecting to separately sold power

amp ............................................................ 5

When connecting with a rear view camera ...... 7

When connecting with a multi-channel

processor .................................................... 8

When connecting with Vehicle Dynamics

Processor and an iPod adapter .................... 9

When connecting with Vehicle Dynamics

Processor and a Bluetooth adapter .......... 10

When connecting the external video

component and the display ...................... 11

Installation ................................................ 12

Installing the remote control unit .................... 12

Installation using the screw holes

on the side of this unit .............................. 13

WARNING

• To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or TV
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.

• In some countries or states the viewing of images
on a display inside a vehicle even by persons
other than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit's DVD features should not be used.

CAUTION:

• PIONEER does not recommend that
you install or service your display your­self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho­rized Pioneer service personnel.

• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.

• Do not drill a hole into the engine com­partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu­lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.

• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.

• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid­ing mechanism.

• Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNEC­TOR IS DESIGNED TO DETECT PARKED
STATUS AND MUST BE CONNECTED TO
THE POWER SUPPLY SIDE OF THE PARK­ING BRAKE SWITCH. IMPROPER CONNEC­TION OR USE OF THIS LEAD MAY VIO­LATE APPLICABLE LAW AND MAY
RESULT IN SERIOUS INJURY OR DAMAGE.

ENG/MASTER 96 INST

<CRD4072-A> 2

Connecting the Units

English

Español

Deutsch

Français

Italiano

Nederlands

<CRD4072-A> 3

ENG/MASTER 96 INST

2

Note:

• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre­ational vehicle, truck, or bus, check the battery
voltage.

• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning

installation.

• Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.

• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insu­lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.

• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.

• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.

• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a
fuse of the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.

• If the RCA pin jack on the unit will not be used,
do not remove the caps attached to the end of the
connector.

• Speakers connected to this unit must be high­power with minimum rating of 50 W and imped­ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers catching
fire, emitting smoke or becoming damaged.

• When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten­na booster power supply terminal.

• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter­minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.

• To avoid short-circuit, cover the disconnected
lead with insulating tape. Insulate the unused
speaker leads without fail. There is a possibility of
a short-circuit if the leads are not insulated.

• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col­ors correctly.

• This unit cannot be installed in a vehicle that
does not have an ACC (accessory) position on
the ignition switch. (Fig. 1)

Fig. 1

• The black lead is ground. Please ground this lead
separately from the ground of high-current prod­ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam­age to the products or fire.

No ACC positionACC position

• Cords for this product and those for other prod­ucts may be different colors even if they have
the same function. When connecting this product
to another product, refer to the supplied manuals
of both products and connect cords that have the
same function.

C

C

A

O

F

N

F

O

S

T

A

R

T

O

F

N

F

O

S

T

A

R

T

3

Connecting the Units

Connecting the power cord

ENG/MASTER 96 INST

4

<CRD4072-A> 4

Yellow
To terminal always supplied
with power regardless of
ignition switch position.

Fuse holder
(10 A)

Red
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.

Black (ground)
To vehicle (metal) body

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

Front speaker

Rear speaker

Front speaker

Rear speaker

Fuse resistor

Multi-CD player
(sold separately)

IP-BUS cable

Left Right

+

≠

+

≠

+

≠

+

≠

Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.

This product

Orange/white
To lighting switch terminal.

16 cm

Fuse resistor

IP-BUS input (Blue)

Violet/white
Refer to page 7.

English

Español

Deutsch

Français

Italiano

Nederlands

Fig. 2

4

ENG/MASTER 96 INST

<CRD4072-A> 5

Antenna cable

AUX input jack

20 cm

When you connect the separately sold multi-channel processor
(DEQ-P7650) to this unit, do not connect anything to the
speaker leads and system remote control (blue/white).

Note:

• The position of the parking brake switch depends
on the vehicle model. For details, consult the
vehicle Owner’s Manual or dealer.

Connection method

Clamp the lead.1. 2. Clamp firmly with

needle-nosed
pliers.

Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).

With a 2 speaker system, do not connect anything
to the speaker leads that are not connected to speakers.

Parking brake
switch

Power supply side

Ground side

Light green
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side of the parking
brake switch.

15 cm

When connecting to separately sold power amp

5

Connecting the Units

ENG/MASTER 96 INST

6

<CRD4072-A> 6

Rear output
(REAR OUTPUT)

This product

When you connect the separately sold
multi-channel processor (e.g. DEQ-P7650)
to this unit, do not connect anything to the
speaker leads and system remote control
(blue/white).

Note :
Change the initial setting of this product
(refer to the Operation Manual).
The subwoofer output of this unit is monaural.

Note :
When you connect the multi-channel processor
to this unit, a separately sold power amp must
be connected to the multi-channel processor.

Front output
(FRONT OUTPUT)

Subwoofer output
or non fading output
(SUBWOOFER OUTPUT or
NON-FADING OUTPUT)

Blue/white
To system control terminal of the power am

p

(max. 300 mA 12 V DC).

R

F

23cm

15cm

15cm

English

Español

Deutsch

Français

Italiano

Nederlands

Fig. 3

6

ENG/MASTER 96 INST

<CRD4072-A> 7

≠

+

≠

+

+

≠

+

≠

≠

+

≠

+

Perform these connections when using the
optional amplifier.

Blue/white

Connecting cords
with RCA pin plugs
(sold separately)

System remote control

Rear speaker

Subwoofer Subwoofer

Rear speaker

Front speaker

Front speaker

Left Right

Power amp
(sold separately)

Power amp
(sold separately)

Power amp
(sold separately)

When connecting with a rear view camera

When using this product with a rear view camera, automatic switching to video from a
rear view camera when the gear shift is moved to REVERSE (R) position is possible.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.

CAUTION

• The screen image may appear reversed.

• The rear view camera function is to use this product as an aid to keep an eye on trailers, or backing into a
tight parking spot. Do not use this function for entertainment purposes.

• The object in rear view may appear closer or more distant than in reality.

Fig. 4

<CRD4072-A> 8

ENG/MASTER 96 INST

7

Connecting the Units

CAUTION

Yo umust use a camera
which outputs mirror

This product

20 cm

10 cm

Back up camera input
(VIDEO 2/BACK UP CAMERA INPUT)

RCA cable
(sold separately)

8m

To video output

Extension lead (supplied)

reversed images.

rear view camera

Violet/white
Of the two lead wires connected to the back
lamp, connect the one in which the voltage
changes when the gear shift is in the REVERSE
(R) position. This connection enables the unit to
sense whether the car is moving forwards or
backwards.

Connection method

Note:

•Itisnecessary to set AV INPUT2 to B.CAMERA in SETUP

Fuse resistor

Clamp the lead.1. 2. Clamp firmly with

needle-nosed
pliers.

when connecting the rear view camera.

English

Español

Deutsch

Français

Italiano

Nederlands

When connecting with a multi-channel processor

Fig. 5

<CRD4072-A> 9

8

ENG/MASTER 96 INST

AV-BUS input

Blue

IP-BUS input
(Blue)

IP-BUS cable
(supplied with
multi-channel processor)

Subwoofer output
(SUBWOOFER OUTPUT o

(Blue)

RCA cable (supplied with
multi-channel processor)

Multi-channel processor
(DEQ-P7650)
(sold separately)

43

cm

16 cm

Blue

This product

or non fading output

NON-FADING OUTPUT)

Optical cable (supplied with
multi-channel processor)

Blue

28 cm

r

Video input

RCA cable
(sold separately)

Optical cable
(sold separately)

To video output

BlueBlack

IP-BUS cable
(supplied with TV
tuner)

AV-BU cable (supplied with TV tuner)

S

Black Blue

Hide-away TV tuner
(e.g. GEX-P5750TV(P) )
(sold separately)

Black

External unit
with optical output
(sold separately)

IP-BUS

IP-BUS cable

output
(Black)

Multi-CD Player
(sold separately)

When you connect External unit with
optical output (sold separately) to the
multi-channel processor (sold
separately), the optical cable from the
External unit must be connected to the
optical cable 2 input (OPT. IN2) on the
multi-channel processor.

Blue

9

Connecting the units

ENG/MASTER 96 INST

10

<CRD4072-A> 10

When connecting with Vehicle Dynamics Processor and an iPod adapter

Fig. 6

26 pin cable input

This product

IP-BUS input (Blue)

IP-BUS cable
(Supplied with
the iPod adapter)

iPod with dock connector

Dock connector port

16 cm

26 pin cable
(supplied with Vehicle
Dynamics Processor)

1.5 m

iPod adapter
(e.g. CD-IB100 —)

Dock connector
(Supplied with the iPod adapter)

Yellow

1.5 m

Vehicle Dynamics Processor
(e.g. AVG-VDP1)
(sold separately)

Black

IP-BUS cable

Blue

Multi-CD player
(sold separately)

10

ENG/MASTER 96 INST

<CRD4072-A> 11

English

Español

Deutsch

Français

Italiano

Nederlands

When connecting with Vehicle Dynamics Processor and a Bluetooth adapter

Fig. 7

This product

IP-BUS input (Blue)

Microphone
for hands-free phoning
(supplied with Bluetooth adapter)

Bluetooth adapter
(e.g. CD-BTB100)

Black

Multi-CD player
(sold separately)

Blue

16 cm

26 pin cable input

Yellow

26 pin cable
(supplied with Vehicle
Dynamics Processor)

Blue

1.5 m

Black

IP-BUS cable
(Supplied with the Bluetooth adapter)

Vehicle Dynamics Processor
(e.g. AVG-VDP1)
(sold separately)

Note :
In some countries, CD-BTB100 is not sold on the market.

11

Connecting the units

ENG/MASTER 96 INST

12

<CRD4072-A> 12

When connecting the external video component and the display

Fig. 8

• It is necessary to set AV INPUT to VIDEO on the SETUP menu when connecting to

external video component.

• It is necessary to set AV INPUT to EXT-V on the SETUP menu when connecting to

DVD player.

When using a display connected to video output

This product’s video output is for connection of a display to enable passengers in the rear
seats to watch the DVD or Video CD.

WARNING:

• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD
while Driving.

This product

Video output
(VIDEO OUTPUT)

Audio 1 input
(AUDIO 1 INPUT)

Video 1 input (VIDEO 1 INPUT)

Audio 2 input
(AUDIO 2 INPUT)

Video 2 input
(VIDEO 2/BACK UP CAMERA INPUT)

RCA cable
(sold separately)

RCA cables (sold separately)

To audio outputs

To video output

RCA cables (sold separately)

To audio outputs

To video output

To video input

External video
component
(sold separately)

External video
component
(sold separately)

Display with
RCA input jacks

ATitle (English)

12

ENG/MASTER 96 INST

<CRD4072-A> 13

English

Español

Deutsch

Français

Italiano

Nederlands

Installation

Note:

• Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect­ed up properly, and the unit and the system work
properly.

• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.

• Consult with your nearest dealer if installation
requires the drilling of holes or other modifica­tions of the vehicle.

• Install the unit where it does not get in the dri­ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.

• Do not install the display where it may (i) obstruct
the driver's vision, (ii) impair the performance of
any of the vehicle's operating systems or safety
features, including air bags, hazard lamp buttons
or (iii) impair the driver's ability to safely operate
the vehicle.

• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 9)

Fig. 9

• The cords must not cover up the area shown in the
figure below. This is necessary to allow the
amplifires to radiate freely. (Fig. 10)

Fig. 10

Installing the remote control unit

When not using the remote control
unit, secure it with velcro tape to pre­vent it from moving.

• Thoroughly wipe off the surface
before affixing the velcro tape.

Fig.11

t

Remote control uni

Velcro tape (small)
(hard)

Velcro tape (small)
(soft)

Leave this space.

13

A Title (English)

ENG/MASTER 96 INST

14

<CRD4072-A> 14

Installation

Installation using the screw holes on the side of this unit

1. Remove the frame.

2. Fastening this unit to the factory radio mounting bracket.

Position this unit so that the brackets screw holes and its screw holes are aligned (are fit­ted), and tighten the screws at 3 or 4 locations on each side. Use either the binding screws
(5 × 6 mm) or flush surface screws (5 × 6 mm), depending on the shape of the bracket’s
screw holes.

Fig. 12

Fig. 13

Factory radio mounting bracket

Binding screw or
flush surface screw
Be sure to use the
screws supplied
with this product.

Dashboard or console

If the pawl gets in the
way, bend it down

Note:

• In some types of automobiles, descrepancy may occur between the main unit and the dashboard. If
this happens, use the supplied panel to fill the gap.

• To some types of automobiles, ths unit cannot be properly installed. In such case, use the installa­tion kit ADT-VA133 (sold separately).