Pioneer AVH-P3100DVD Installation Manual

DVD AV RECEIVER AUTORADIO AV LECTEUR DE DVD RADIO AV CON DVD

AVH-P3100DVD

English Français Español

Installation Manual

Manuel d’installation

Manual de instalación

Contents

Connecting the units

Connecting the units ............................ 2

Parts supplied .................................................. 4

Connecting the system ....................................5

Connecting the power cord

...............................

When connecting to

separately sold power amp ........................ 8

When connecting

with a rear view camera ..............................9

When connecting

with a multi-channel processor ...............10

Connecting and installing

the optical cable connection box ............. 11

Connecting the optical cable .................................11

Installing the optical cable connection box ..........11

When connecting the external

video component and the display ............ 12

When using a display connected to

rear video output ............................................12

Installation ........................................... 13

Installation using the screw holes

on the side of the unit ............................. 13

WARNING

• To avoid the risk of accident and the potential

violation of applicable laws, the front DVD or TV (sold separately) feature should never be used while the vehicle is being driven. Also, rear displays should not be in a location where it is a visible distraction to the driver.

• In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed and this unit’s DVD features should not be used.

CAUTION

• PIONEER does not recommend that you install or service your display yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to authorized Pioneer service personnel.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed.

• Do not drill a hole into the engine compartment to connect the yellow lead of the unit to the vehicle battery. Engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. Take extra care in securing the wire at this point.

• It is extremely dangerous to allow the display lead to become wound around the steering column or gearshift. Be sure to install the display in such a way that it will not obstruct driving.

• Make sure that wires will not interfere with moving parts of the vehicle, such as the gearshift, parking brake or seat sliding mechanism.

• Do not shorten any leads. If you do, the protection circuit may fail to work properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR

IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Connecting the units

Note

• This unit cannot be installed in a vehicle without ACC (accessory) position on the ignition switch.

ACC position

No ACC position

• Use this unit in other than the following conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a battery.

— Cover any disconnected cable connectors with

insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable directly

to ground. — Never band together multiple speaker’s

negative cables.

• Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.

• Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result.

• IP-BUS connectors are color-coded. Be sure to connect connectors of the same color.

• Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached.

English

Connecting the units

Parts supplied

This product Power cord Frame

Flush surface screw

(5 × 6 mm) (8 pcs.)

Binding screw

(5 × 6 mm) (8 pcs.)

Touch panel pen

Connecting the units

Connecting the system

English

Wired remote input Hard-wired remote control adaptor can be connected (sold separately).

This product

Multi-CD player (sold separately)

Blue

IP-BUS input (Blue)

IP-BUS cable

Microphone for hands-free phoning (supplied with Bluetooth adapter)

Bluetooth adapter (e.g. CD-BTB200) (sold separately)

Blue

IP-BUS cable (Supplied with Bluetooth adapter)

Black

Connecting the units

Connecting the power cord

Yellow Connect to the constant 12 V supply terminal.

This product

Antenna input

Fuse (10 A)

Orange/white Connect to lighting switch terminal.

Red Connect to terminal controlled by ignition switch (12 V DC).

Black (chassis ground) Connect to a clean, paint-free metal location.

Front speaker Front speaker

Left Right

Rear speaker or Subwoofer (4 Ω)

When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything to Green and Green/black leads.









Not used.

White Gray

Gray/blackWhite/black

Green Violet

Green/black Violet/black

Green

Green/black

Violet

Violet/black













Fuse resistor

Rear speaker or Subwoofer (4 Ω)

Subwoofer (4 Ω) × 2

Connecting the units

Fuse resistor

Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forwards or backwards.

Yellow/black If you use equipment with Mute function, wire this lead to the Audio Mute lead on that piece of equipment. If not, keep the Audio Mute lead free of any connections.

Connection method

English

1. Clamp the lead.

Note:

· The position of the parking brake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer.

Light green Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch.

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.

When you connect the separately sold multi-channel processor (DEQ-P8000) to this unit, do not connect anything to the speaker leads and system remote control (blue/white).

Power supply side

Ground side

Note:

· Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural.

2. Clamp firmly with needle-nosed pliers.

Parking brake switch

Connecting the units

When connecting to separately sold power amp

Rear output or subwoofer output

Front output

To rear output or subwoofer output

Power amp (sold separately)

This product

To front output

Connect with RCA cables (sold separately)

Power amp (sold separately)

Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC).

When you connect the separately sold multi-channel processor (DEQ-P8000) to this unit, do not connect anything to the speaker leads and system remote control (blue/white).

When you connect the multi-channel processor to this unit, refer to multi-channel processor’s installation manual for the connection method.

Note:

· Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural.

System remote control

Left Right

Front speaker Front speaker

Rear speaker or Subwoofer















Rear speaker



or Subwoofer

Perform these connections when using the optional amplifier.

Connecting the units

When connecting with a rear view camera

When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the gear shift is moved to REVERSE (R).

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY

RESULT IN INJURY OR DAMAGE.

CAUTION

• The screen image may appear reversed.

• The rear view camera function is to be used as an aid for backing into a tight parking spot. Do not use this function for entertainment purposes.

• Objects in the rear view may appear closer or more distant than they actually are.

CAUTION

English

Rear view camera input

This product

• It is necessary to set Camera Polarity properly in System Menu when connecting the rear view camera.

(REAR CAMERA IN)

To video output

RCA cable (sold separately)

You must use a camera which outputs mirror reversed images.

Rear view camera

Fuse resistor

Connecting the units

When connecting with a multi-channel processor

Microphone for hands-free phoning (supplied with Bluetooth adapter)

Wired remote input Hard-wired remote control adaptor can be connected (sold separately).

This product

To SWL

To SWR

Optical output (Black)

Blue

IP-BUS input (Blue)

Blue

IP-BUS cable (Supplied with Bluetooth adapter)

Bluetooth adapter (e.g. CD-BTB200) (sold separately)

Black

RCA cable (supplied with multi-channel processor)

IP-BUS cable (supplied with multi-channel processor)

Optical cable connection box (supplied with multi-channel processor)

Optical cable (supplied with multi-channel processor)

Blue

Multi-channel processor (DEQ-P8000) (sold separately)

Black

Blue

IP-BUS cable

Multi-CD player (sold separately)

Connecting the units

Connecting and installing the optical cable connection box

WARNING

• Avoid installing the optical cable connection box in locations where the operation of safety devices such as airbags is prevented by this unit. Otherwise, there is a danger of a fatal accident.

• Avoid installing the optical cable connection box in locations where the operation of the brake may be prevented. Otherwise, it may result in a traffic accident.

• Fix the optical cable connection box securely with the hook and loop fastener or lock tie. If the unit is loose, it disturbs driving stability, which may result in a traffic accident.

CAUTION

• Install this unit using only the parts supplied with this unit. If other parts are used, this unit may be damaged or could dismount itself, which leads to an accident or other problems.

• Do not install this unit near the doors where rainwater is likely to be spilled on the unit. Incursion of water into the unit may cause smoke or fire.

Connecting the optical cable

1. Connect the optical cable and ground

lead to the main unit.

Connect the optical cable so that it does not protrude from the main unit, as shown in the illustration. Fasten the ground lead to the protrusion on the back of the main unit.

Installing the optical cable connection box

• When installing the optical cable connection box with the hook and loop fastener.

Install the optical cable connection box using the hook and loop fastener in the ample space of the console box.

Hook fastener

Loop fastener

• When installing the optical cable connection box with the lock tie.

Wrap the optical cable and connection box with the protection tape and fasten with the power code using the lock tie.

Wrap with the protection tape

Fasten with the lock tie

English

Screw

2. Connect the optical cable to the optical cable connection box.

Optical cable

Connecting the units

When connecting the external video component and the display

Display with RCA input jacks (sold separately)

To video input

RCA cables (sold separately)

Video input (V IN)

Rear monitor output (V OUT)

To video output

This product

• It is necessary to change AV Input in System Menu when connecting the external video

component.

Audio input (L IN, R IN)

To audio outputs

External video component (sold separately)

When using a display connected to rear video output

This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch video.

WARNING

Never install the display in a location where it is visible to the driver while driving.

+ 26 hidden pages