Introduction 5
What’s in the box 5
Overview of the main unit 6
Overview of the remote control 7
3 Get started 9
Install batteries to the main unit 9
Prepare the remote control 9
Connect power 10
Set time and date 10
Turn on 10
4 Play 11
Play from iPod/iPhone/iPad 11
Play from an external device 11
Adjust sound 12
5 Listen to radio 12
Listen to DAB+ radio 12
Listen to FM radio 14
6 Other features 15
Set the alarm timer 15
Set the sleep timer 15
Adjust display brightness 15
English
7 Product information 16
Specifications 16
8 Troubleshooting 17
9 Notice 18
EN
3
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated
material within your unit may cause an
electrical shock. For the safety of everyone
in your household, please do not remove
product covering.
The ‘exclamation point’ calls attention to
features for which you should read the
enclosed literature closely to prevent
operating and maintenance problems.
WARNING: To reduce the risk of fire or
electric shock, this apparatus should not be
exposed to rain or moisture and objects filled
with liquids, such as vases, should not be
placed on this apparatus.
CAUTION: To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
Important Safety instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
h Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
i Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and
the point where they exit from the
apparatus.
j Only use attachments/accessories
specified by the manufacturer.
k Use only with the cart, stand,
tripod, bracket, or table specified by
the manufacturer or sold with the
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tipover.
l Unplug this apparatus during lightning
storms or when unused for long periods
of time.
m Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
4
EN
n Battery usage CAUTION – To prevent
battery leakage which may result in
bodily injury, property damage, or
damage to the unit:
Install all batteries correctly, + and - •
as marked on the unit.
Do not mix batteries (old and new •
or carbon and alkaline, etc.).
Remove batteries when the unit is •
not used for a long time.
Batteries (battery pack or batteries •
installed) shall not be exposed to
excessive heat such as sunshine, fire
or the like.
o Apparatus shall not be exposed to
dripping or splashing.
p Do not place any sources of danger on
the apparatus (e.g. liquid filled objects,
lighted candles).
q Where the plug of the Direct Plug-
in Adapter is used as the disconnect
device, the disconnect device shall
remain readily operable.
2 Your Docking
Entertainment
System
Congratulations on your purchase, and
welcome to Philips! To fully benefit from
the support that Philips offers, register your
product at www.philips.com/welcome.
Introduction
With this unit, you can:
listen to FM/DAB+ radio;•
enjoy audio from iPod/iPhone/iPad or •
other audio devices;
set two alarms; and•
wake up by buzzer alarm, radio, or audio •
in iPod/iPhone/ipad.
English
Warning
Never remove the casing of this apparatus. •
Never lubricate any part of this apparatus. •
Never place this apparatus on other electrical •
equipment.
•
Keep this apparatus away from direct sunlight, naked
flames or heat.
•
Ensure that you always have easy access to the
power cord, plug or adaptor to disconnect the
apparatus from the power.
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er derfor
ikke frakoplet nettet så lenge apparatet er
tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
What’s in the box
Check and identify the contents of your
package:
Main unit•
Remote control•
Power adapter•
MP3 link cable x 1•
User manual•
Quick start guide•
If you contact Philips, you will be asked for the
model and serial number of this apparatus.
The model number and serial number are on
the rear of the apparatus. Write the numbers
here:
Model No. _________________________
Serial No. __________________________
EN
5
Overview of the main unit
p
o
FM
ANTENNA
n
m
l
k
j
i
SET TIME
AUTO SCAN
VOL
MENU
SLEEP
VOL
ALARM 1
-
K
N
I
L
DC IN
P
M
3
9
V
REPEAT ALARM
BRIGHTNESS CONTROL
a
1.9A
b
c
d
e
f
g
h
ALARM 2
SOURCE
TUNING
PRESET
TUNING
PRESET
a DC IN
Connect power.•
b DOCK for iPod/iPhone/iPad
Load an iPod/iPhone/iPad.•
c PRESET +/-
Select a preset radio station.•
Navigate through iPod/iPhone/iPad •
menu.
Adjust time.•
d TUNING +/-
Tune to a radio station.•
Skip to the previous/next audio file.•
Search within an audio file.•
Adjust time.•
6
EN
/
e OK/
Start/pause play.•
Confirm a selection.•
f SOURCE
Select a source: iPod/iPhone/iPad, •
DAB+/FM tuner, or MP3 link.
g REPEAT ALARM/BRIGHTNESS
CONTROL
Repeat alarm.•
Adjust display brightness.•
h Display panel
Show current status.•
i ALARM 1/ALARM 2
Set alarm timer.•
View alarm settings.•
Activate/deactivate alarm timer.•
j
Turn on the unit or switch to standby •
mode.
Deactivate sleep timer.•
k SET TIME/AUTO SCAN/
Set time and date.•
Store radio stations automatically/•
manually.
l SLEEP
Set sleep timer.•
m VOL +
n MENU/
o FM antenna
p MP3-LINK
/VOL -
Adjust volume.•
Access iPod/iPhone/iPad/DAB+ •
menu.
Improve FM reception.•
Connect an external audio device.•
Overview of the remote
control
a
b
c
d
e
f
g
h
i
j
k
English
n
m
l
a POWER
Turn on the unit or switch to standby •
mode.
Deactivate sleep timer.•
b MENU
Access iPod/iPhone/iPad/DAB+ •
menu.
c PRESET +/-
Select a preset radio station.•
Navigate through iPod/iPhone/iPad •
menu.
Adjust time.•
EN
7
d TUNING +/- /
Skip to previous/next audio file.•
Search within an audio file.•
Tune to a radio station.•
Adjust time.•
e OK/
Start/pause play.•
Confirm a selection.•
f Source selection keys: (FM/DAB, MP3
LINK, and DOCK)
Select a source: FM/DAB+ tuner, •
MP3 link, or iPod/iPhone/iPad.
g SET TIME/AUTO SCAN
Set the time and date.•
Store radio stations automatically/•
manually.
h REP AL/BRIGHTNESS
Adjust display brightness.•
Repeat alarm.•
i DBB
Turn on or off dynamic bass •
enhancement.
j DSC
Select a preset sound setting.•
k AL 1/AL 2
View alarm settings.•
Set alarm timer.•
Activate/deactivate alarm timer.•
l VOL+/-
Adjust time.•
m INFO
Show DAB+/RDS information.•
n SLEEP
Set sleep timer.•
8
EN
3 Get started
Caution
Use of controls or adjustments or performance •
of procedures other than herein may result in
hazardous radiation exposure or other unsafe
operation.
1 Open the battery compartment.
2 Insert 2 x AA batteries with correct
polarity (+/-) as indicated.
3 Close the battery compartment.
Prepare the remote control
English
Always follow the instructions in this chapter
in sequence.
Install batteries to the main
unit
Caution
Risk of explosion! Keep batteries away from heat, •
sunshine or fire. Never discard batteries in fire.
•
Remove battery if it is exhausted or will not be used
for a long time.
Batteries contain chemical substances, so they should •
be disposed of properly.
Note
You can only use AC power as power supply. •
Batteries (not supplied) are for backup purpose.
Caution
Risk of explosion! Keep batteries away from heat, •
sunshine or fire. Never discard batteries in fire.
•
Danger of explosion if bat ter y is incorrectly replaced.
Replace only with the same or equivalent type.
•
Keep children away from the bat tery.
For first-time use:
Remove the protective tab to activate the
remote control battery.
To replace the remote control battery:
1 Pull out the battery tray and remove the
old battery.
2 Place a new lithium CR2025 battery with
correct polarity (+/-) as indicated.
3 Insert the battery tray back into the slot.
2
x AA
2
x AA
Note
Before you press any function button on the remote •
control, first select the correct source with the
remote control instead of the main unit.
9
EN
Connect power
Caution
Risk of product damage! Ensure that the power •
voltage corresponds to the voltage printed on the
back or underside of the unit.
•
Risk of electric shock! When you unplug the power
adapter, always pull the plug from the socket. Never
pull the cord.
•
Before connecting the power adapter, ensure that
you have completed all other connections.
•
Use the supplied power adapter only.
Note
The type plate is located on the bottom of the main •
unit.
Connect the power adapter to:
the • DC IN socket at the back of the
unit.
the wall socket.•
3 Press SET TIME to confirm.
» [24H] or [12H] begins to blink.
4 Press / or / to select the 12/24
hour format.
5 Press SET TIME to confirm.
The hour digits begin to blink. »
6 Repeat steps 4-5 to set the hour, minute,
year, month, and day.
Note
If clock is not manually set, when iPod/iPhone/iPad •
is connected, the unit synchronizes time from the
iPod/iPhone/iPad automatically.
Tip
The accuracy of the transmitted time depends on the •
DAB+ station or the docked iPod/iPhone/iPad that
transmits the time signal.
Turn on
Set time and date
1 In standby mode, press and hold SET
TIME for 2 seconds.
» [SYNC ON] is displayed and [ON]
begins to blink.
2 Press / or / repeatedly to select
ON or OFF.
» [ON]: The unit synchronizes time
from the DAB+ station.
» [OFF]: The time synchronization with
DAB+ station is deactivated.
10
EN
Press POWER.
The unit switches to the last selected »
source.
Tip
To select a source, press •SOURCE repeatedly or the
source selection buttons on the remote control.
Switch to standby mode
Press POWER again to switch the unit to
standby mode.
The time and date (if set) appear on »
the display panel.
4 Play
Play from iPod/iPhone/iPad
You can enjoy audio from iPod/iPhone/iPad
through this unit.
Compatible iPod/iPhone/iPad
The unit supports the following iPod, iPhone
and iPad models:
Made for.
Keep the unit away from other electronic devices to •
avoid radio inter ference.
•
For better reception, do not place iPod/iPhone/iPad
into the dock when you listen to the radio. Fully
extend and adjust the position of the antenna.
Listen to DAB+ radio
DAB+ (Digital Audio Broadcasting) is a way
of broadcasting radio digitally through a
network of transmitters. It provides you with
more choice, better sound quality, and more
information.
Press FM/DAB repeatedly to select DAB+
mode.
The unit automatically stores all the »
available DAB+ radio stations and
then broadcasts the first available
station.
If no DAB service is available, »[NO
SERV] (no service)is displayed.
Store DAB+ radio stations
automatically
In DAB+ mode, press and hold AUTO SCAN
for 3 seconds.
The unit stores all the available DAB+ »
radio stations automatically and then
broadcasts the first available station.
Store DAB+ radio stations manually
1 Tune to a DAB+ radio station.
2 Press AUTO SCAN to activate the
storing mode.
3 Press PRESET +/- to select a number.
4 Press AUTO SCAN to confirm.
12
EN
5 Repeat the above steps to store other
DAB+ stations.
Note
To remove a pre-stored DAB+ radio station, store •
another station in its place.
Listen to a preset DAB+ radio
station
1 In DAB+ mode, press / repeatedly
to select a DAB+ radio station.
2 Press OK to confirm.
Note
If no DAB+ radio station is available, the steps •
mentioned above are invalid.
Use DAB+ menu
1 In DAB+ mode, press and hold MENU to
enter the DAB+ menu.
2 Press / repeatedly to navigate
through the options:
• [MANUAL]: Tune to a specific
channel manually.
• [SCAN]: Perform a wide range of
DAB+ radio search.
• [DRC]: Add or remove a degree of
compensation for the differences in
the dynamic range between radio
stations.
• [TUNERRST]: Reset the tuner.
• [VERSION]: Display software
version.
3 To select an option, press OK.
4 Repeat steps 2-3 if sub-option is available
under one option.
[MANUAL]
1 In DAB+ mode, press MENU repeatedly
until [MANUAL] is displayed.
2 Press OK to confirm.
A channel and its frequency appear »
on the display.
3 Press / repeatedly to tune to a
DAB+ radio station.
4 Press OK to confirm.
[DRC] (Dynamic Range Control)
• [DRC 0]: No compensation applied.
• [DRC 1/2]: Medium compensation
applied.
• [DRC 1]: Maximum compensation
applied (the default option
recommended for noisy
environment).
[TUNERRST]
• [YES]: Reset the tuner.
• [NO]: Cancel.
Tip
If no button is pressed within 10 seconds, the menu •
exits.
Show DAB+ information
While listening to DAB+ radio, press INFO
repeatedly to scroll through the following
information (if available):
Dynamic Label Segment (DLS) »
Signal strength »
Program type (PTY) »
Ensemble Name »
Channel and frequency »
Signal error rate »
Bit rate and audio status »
Date »
English
EN
13
Listen to FM radio
Tune to FM radio stations
1 Press FM/DAB to select FM tuner.
2 Press and hold TUNING +/- for 2
seconds.
The unit tunes to an FM radio station »
with strong reception automatically.
3 Repeat step 2 to tune to more FM
stations.
To tune to a weak station, press •
TUNING +/- repeatedly until you
find optimal reception.
Listen to a preset FM radio station
In FM tuner mode, press PRESET +/-
repeatedly to select a preset number.
Select stereo/mono broadcast
Note
Stereo broadcast is the default setting for FM tuner •
mode.
•
For stations with weak signals, to improve the
reception, change to monaural sound.
In FM tuner mode, press OK repeatedly to
switch between mono and stereo broadcast.
Store FM radio stations automatically
You can store a maximum of 20 FM radio
stations.
In FM tuner mode, press and hold AUTO SCAN for 2 seconds.
The unit stores all the available FM »
radio stations automatically and then
broadcasts the first available station.
Store FM radio stations manually
1 Tune to an FM radio station.
2 Press AUTO SCAN to activate the
storing mode.
3 Press PRESET +/- to select a number.
4 Press AUTO SCAN to confirm.
5 Repeat the above steps to store other
stations.
Tip
To remove a pre-stored station, store another •
station in its place.
Show RDS information
RDS (Radio Data System) is a service that
allows FM stations to show additional
information. If you tune to a RDS station, the
station name is displayed.
1 Tune to an FM station with RDS signal.
2 Press INFO repeatedly to scroll through
the following information (if available):
Station name »
Radio text messages »
Program type such as »[NEWS]
(news), [SPORT] (spor t), [POP M]
(pop music)...
14
EN
6 Other features
Set the alarm timer
Repeat alarm
When alarm rings, press REPEAT ALARM.
The alarm repeats ringing minutes »
later.
English
You can set two alarms to ring at different
time.
Note
Ensure that you have set the clock correctly. (See •
“Get started - Set time and date”.)
1 Press and hold ALARM 1 or ALARM 2
for 2 seconds.
»
[AL1]/ [AL2] and the hour digits
begin to blink.
2 Press / or / repeatedly to set
the hour.
3 Press ALARM 1 or ALARM 2 to confirm.
»
[AL1] / [AL2] and the minute
digits begin to blink.
4 Repeat steps 2-3 to set the minute.
5 Repeat steps 2-3 to select whether
to ring alarm for the whole week, on
weekdays, or at weekend.
6 Repeat steps 2-3 to select an alarm sound
source: Buzzer, iPhone, FM, or DAB+.
7 Repeat steps 2-3 to set the alarm volume.
Tip
You can press •REPEAT ALARM repeatedly to adjust
the interval (5-30 minutes) to repeat alarm.
Stop alarm ring
When the alarm rings, press the
corresponding ALARM 1 or ALARM 2.
The alarm stops but the alarm »
settings remain.
Set the sleep timer
This unit can switch to standby mode
automatically after a preset time period.
Press SLEEP repeatedly to select the sleep
timer period (in minutes).
When the sleep timer is activated, »
appears.
To deactivate the sleep timer:
Press SLEEP repeatedly until [OFF] (off ) is
displayed.
Activate/deactivate the alarm timer
Note
Ensure that you have already set the alarms •
successfully.
1 Press ALARM 1/ALARM 2 to view the
alarm settings.
2 Press ALARM 1/ALARM 2 repeatedly to
activate or deactivate the alarm timer.
The alarm icon appears if the alarm »
timer is on and disappears if it is off.
Adjust display brightness
Press BRIGHTNESS CONTROL repeatedly
to select different brightness levels.
EN
15
7 Product
information
Speakers
Speaker Impedance4 ohm
Sensitivity>82dB/m/W
Note
Product information is subject to change without •
prior notice.
Specifications
Amplifier
Rated Output Power2 x 5 W RMS
Frequency Response20 -20000 Hz,
-3dB
Signal to Noise Ratio>67 dB
Total Harmonic Distortion <1%
Aux Input (MP3 link)0.5 V RMS
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome). When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
No power
Ensure that the AC power plug of the •
unit is connected properly.
Ensure that there is power at the AC •
outlet.
Ensure that the batteries are inser ted •
correctly.
No sound
Adjust the volume. •
No response from the unit
Disconnect and reconnect the AC power •
plug, then turn on the unit again.
Poor radio reception
Increase the distance between the unit •
and your TV or VCR.
Fully extend the FM antenna. •
Alarm does not work
Set the clock/alarm correctly. •
Clock/alarm setting erased
Power has been interrupted or the power •
plug has been disconnected.
Reset the clock/alarm. •
English
EN
17
9 Notice
This product complies with the radio
interference requirements of the European
Community.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
“Made for iPod,” “Made for iPhone,” and
“Made for iPad” mean that an electronic
accessory has been designed to connect
specifically to iPod, iPhone, or iPad,
respectively, and has been certified by the
developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance
with safety and regulatory standards. Please
note that the use of this accessory with
iPod, iPhone, or iPad may affect wireless
performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries. iPad
is a trademark of Apple Inc.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment
and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.