Pelco SD436-PRE0, SD436-PRE1, SD436-PRME0, SD436-PRME1, SD436-PRSE1 Quick Start Guide

ADDENDUM

Addendum No.	C2262M-A
Date	October 1, 2012
Documents Affected	C3444M-A Spectra® IV IP Series Dome System
	Operation/Configuration manual (pp. 11 and 25)
	C3434M-C Spectra® IV SE Horizon Series Dome Drive
	manual (pp. 23, 68, and 69)
	C3463M-C Spectra® IV SL and Spectra IV SE Series
	Installation/Operation manual (pp. 1, 8, 18, 24 to 26, 30, 34, 36, 39, 41,
	43, 46, 55, 64, and 65)
	C3462M Spectra® IV SL and Spectra IV SE Series Dome Systems
	Quick Start guide (pp. 1 and 10)
Document Update	This addendum describes changes to model numbers, component
	numbers, and camera/optics specifications.

Changes to Spectra IV Model/Component Numbers

•All 35X models have been replaced by 36X models. For example, SD4E35-F0 has been replaced by SD4E36-F0.

•All references to TXB-IP have been replaced with TXB-N.

•The following component model numbers have changed:

Obsolete 35X	Replacement 36X
Component Model Number	Component Model Number
DD4CBW35 (NTSC)	DD436 (NTSC)
DD4CBW35-X (PAL)	DD436-X (PAL)
Obsolete 27X	Replacement 29X
Component Model Number	Component Model Number
DD427 (NTSC)	DD429 (NTSC)
DD427-X (PAL)	DD429-X (PAL)

C2262M-A (9/12)

Changes to Spectra IV Product Specifications

	Feature	Obsolete 35X	Replacement 36X
		Specifications	Specifications
	Lens Local Length	3.4 mm	3.3 mm
	Zoom	35X optical	36X optical
	Horizontal Angle of View	55.8° at 3.4 mm wide zoom	57.2° at 3.3 mm wide zoom

	Feature	Obsolete 27X	Replacement 29X
		Specifications	Specifications
	Lens Focal Length	91.8 mm	98.6 mm
	Zoom	27X optical	29X optical
	Horizontal Angle of View	2.3° at 91.8 mm telephoto zoom	1.7° at 98.8 mm telephoto zoom

REVISIONI I	HISTORY	DO NOT COPY TEXT FROM THIS TEXT BOX - PLACEHOLDER INFO ONLY!
Document #	Date	Comments
Manual #
C2262M	5/12	.
CxxxxM	x/xx	Original version.
C2262M-A	10/12	Reformatted document size.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies.

Product specifications and availability are subject to change without notice. © Copyright 2012, Pelco, Inc. All rights reserved.

Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone] www.pelco.com www.pelco.com/community

Q U I C K S T A R T

Spectra® IV SL and

Spectra IV SE Series

Dome Systems

23X, 27X, and 35X Models

C3462M (9/09)

Installing the Dome Drive

1.Perform one of the following options:

•View video using both analog and IP connections: Set the DIP switches on the top of the Spectra IV dome drive (refer to Figure 12). For DIP switch settings, refer to the labels located on the top of the dome drive, or refer to Switch Settings on page 3.

•View video using the IP connection: If your dome drive is part of a Spectra IV IP system, you do not need to set the DIP switches.

NOTE: When connecting more than one Spectra IV dome to a single controller, terminate the unit farthest from the controller. To terminate the dome drive set the SW2-10 switch to the ON position.

Figure 1. Setting the DIP Switches

2.Install the dome drive into the back box.

a.Align the blue and red tabs with the blue and red labels on the back box.

b.Push in the red tab and insert that side of the dome drive first.

c.Push in the blue tab and insert the dome drive into the back box the remainder of the way.

d.Continue pushing on the ends of the tabs until both sides click firmly into place.

2	C3462M (9/09)

SWITCH SETTINGS

WARNING: If you are using Pelco D-type or P-type control, your system may not operate if the baud rate and address switches are not set correctly. The switches are set at the factory at the defaults for Pelco D-type control (2400 baud and address 1).

Table A. Switch Settings for SW2

Special Systems
Switch Number	1	2	3	4	5	6	7	8	9	10
AD-32 Preset System	ON
CM9502 Setting		ON
Pelco Coaxitron Controller			OFF
Third-Party Coaxial Control			ON
Third-Party Pelco P-type Control			ON
Serial Port Settings
Switch Number	1	2	3	4	5	6	7	8	9	10
RS422				OFF	OFF
RS485, 4-Wire				OFF	ON
RS485, 2-Wire				ON	ON
Pelco D or P Protocol Baud Rate
Switch Number	1	2	3	4	5	6	7	8	9	10
2400 Baud (Default for D-type Control)						OFF	OFF	OFF
4800 Baud (Default for P-type Control)						ON	OFF	OFF
9600 Baud						OFF	ON	OFF
Video Cable Type
Switch Number	1	2	3	4	5	6	7	8	9	10
Coaxial Cable									OFF
UTP Cable									ON
Dome Termination
Switch Number	1	2	3	4	5	6	7	8	9	10
Terminated										ON
Not Terminated										OFF

C3462M (9/09)

3