Pelco CCC1390H-6X, CCC1390H-6, CCC1390H-6K User Manual

C2924M-QS (4/05)

MAIN MENU

PROFILES > EXPOSURE SETTINGS > FUNCTION SETTINGS > CAMERA SETUP > AI AUTO ADJUSTMENT > PIXEL CORRECTION > SYSTEM INFORMATION >

EXIT

PROFILES

ACTIVE > STANDARD SAVE AS > CUSTOM *DEFAULT STANDARD

BACK EXIT

EXPOSURE SETTINGS

AUTO EXPOSURE > NORMAL VIDEO LEVEL > 0 FLICKERLESS > OFF AGC > ON DSS(SENS) > 4 DAY & NIGHT > COLOR D&N DETECTION > D&N FILTER LIMIT > BACK EXIT

FUNCTION SETTINGS

LINE SYNC > WHITE BALANCE > AUTO MANUAL RED/BLUE > GAMMA > 60%(NORM) SHARPNESS > E-ZOOM > MASKING > TITLE > BACK EXIT

CAMERA SETUP

ADDRESS > 1 COM SPEED > 4800 LED > ON SWITCH > ON

BACK EXIT

AI AUTO ADJUSTMENT

OK CANCEL

PIXEL CORRECTION

COVER THE LENS AND SELECT OK

OK CANCEL

SYSTEM INFORMATION

FIRMWARE VERSION 1.0 OSD VERSION 1.0

RESTORE FACTORY SETTINGS >

BACK EXIT

RESTORE FACTORY SETTINGS

OK CANCEL

CCC1390H Series Camera Quick Start Guide

This quick start guide describes how to install and conﬁgure the CCC1390H Series camera in most applications. It contains a representation of the setup menus to help you locate and change speciﬁc settings.

Refer to the enclosed CD for the following documentation:

•

Installation/Operation manual: INSTALL.PDF

•

Quick Start Guide: QSG.PDF

•

Important Safety Instructions: SAFETY.PDF

MODELS

CCC1390H-6 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, NTSC format

CCC1390H-6X 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, PAL format





Lens Mount



Back Focus Locking Screw



Camera Mount and



Serial Terminating Switch



Auto Iris Lens Connector



Adapter



Video Output Connector



Setup Button



Power Terminal Strip



Indicators

 







SETUP MENUS

Use the setup menus to customize the camera settings. Refer to the setup menus as shown on this and the opposite page.

LINE SYNC

LINE SYNC > AUTO V-PHASE ADJ >

BACK EXIT

MANUAL RED/BLUE

RED GAIN > -1 BLUE GAIN > -2 RED HUE > 1 BLUE HUE > 1

BACK EXIT

E-ZOOM

ZOOM > OFF POSITION >

BACK EXIT

MASKING

MASK > OFF MASK EDIT > MASK ERASE

BACK EXIT

TITLE

TITLE > OFF EDIT TITLE >

BACK EXIT

V-PHASE ADJ

PHASE VALUE = 45

SHARPNESS

APERTURE GAIN > -1

BACK EXIT

POSITION

MASK SETTING

EDIT TITLE

ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789-/

BACK BS

________________

LENS

The CCC1390H Series camera supports both manual and DC-drive auto iris lenses, either ﬁxed focal length or varifocal. It automatically senses an auto iris lens as soon as you plug in the connector. The camera has a standard CS-mount that can accept a C-mount lens with a PCMA40 lens adapter.

To mount the lens onto the camera:

1. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign matter between the lens and the camera imager.

C-mount lens:

Screw the adapter onto the lens.

3. Screw the lens onto the lens mount.

DC-drive auto iris lens:

Connect the four-pin connector from the lens to the connector on the

back of the camera.

MOUNT

The CCC1390H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use a standard 1/4-20 screw. The maximum thread depth (top) is 0.188 inches (4.7 mm). To extend the thread depth (top) to 0.25 inches (6.4 mm), use the camera mount spacer (supplied). The maximum thread depth (bottom) is 0.25 inches (6.4 mm).

ELECTRICAL

Power

Connect 12 VDC or 24 VAC power to the three-pin terminal strip on the back of the camera. Use a Class 2 isolated power source for the CCC1390H camera that can supply 12 VDC ±15% or 24 VAC ±15%, 50/60 Hz. Maximum power consumption is about 3.5 watts.

Video

Connect a coaxial video cable to the BNC connector on the back of the camera.

External Control

For serial control, install the control connector (refer to Operation manual for more information).

Connecting External Control

in the Installation/

ACCESSING THE SETUP MENUS

Use the ﬁve-position button on the rear panel to access and navigate the setup menus. The following table lists the button presses for each menu action.

MENU ACTION BUTTON ACTION

Enter setup menus. Long center press

Move up or down in menu or item options. Up or down press

Move right or left in menu. Right or left press

Select menu or item. Short center press

Save setting and exit to menu. Short center press

NOTE:

After you customize any aspect of the CCC1390H Series camera, be sure to save your custom

settings. (Refer to

Proﬁles

in the Installation/Operation manual for information about saving custom

settings.)

LENS FOCUS

After mounting the lens, you must focus your CCC1390H Series camera. You will adjust both the back focus (on the camera) and the ﬁne focus (on the lens).

NOTE:

The back focus has already been adjusted using a standard CS-mount lens. However, you might

need to adjust it again to match the mounted lens.

Auto iris only:

with a suitable neutral density (ND) ﬁlter. This opens the iris fully. For best results, use an ND3 ﬁlter.

Manual iris only:

completely. The ﬁgure shows the manual iris, varifocal, and lens focus locking screws for a sample lens. Refer to your lens documentation for more information.

3. If necessary, enable Automatic Gain Control (AGC) on the EXPOSURE SETTINGS menu. AGC is enabled by default.

a. Display the EXPOSURE

b. Change AGC to ON.

c. Select EXIT to save the AGC

4. Aim the camera at the farthest object in the ﬁeld of view. Make sure it is at least 6.5 ft (2 m) away.

Fixed focal length lens only:

a. Set the lens focal length to far (∞).

b. Adjust the back focus:

WARNING:

camera.

c. Adjust the lens focus to achieve the best ﬁne focus.

Cover the auto iris lens

MANUAL IRIS LOCKING SCREW

Open the iris

SETTINGS menu.

LENS FOCUS LOCKING SCREW

VARIFOCAL LOCKING SCREW

1.5 MM ALLEN WRENCH

setting.

(1) Use a 1.5-mm Allen wrench to loosen the back focus locking screw.

(2) Turn the lens until the image is focused.

(3) Tighten the back focus locking screw clockwise.

Do not over-tighten the back focus locking screw because you may damage the

Back focus is a coarse adjustment. You will make the ﬁne focus adjustment in the next step.

Varifocal lens only:

a. Set the varifocal to wide (W) and the lens focal length to far (∞).

b. Adjust the back focus:

(1) Use a 1.5-mm Allen wrench to loosen the back focus locking screw.

(2) Turn the lens until the image is focused.

(3) Tighten the back focus locking screw clockwise.

WARNING:

Do not over-tighten the back focus locking screw because you may damage the

camera.

Back focus is a coarse adjustment. You will make the ﬁne focus adjustment in steps c and d.

c. Move the varifocal locking screw up or down to set the ﬁeld of view.

d. Adjust the lens focus to achieve the best ﬁne focus.

e. Repeat steps c and d until the focus is correct.

Manual iris only:

Adjust the iris for the best picture quality. The largest aperture gives the best

light sensitivity; the smallest aperture gives the greatest depth of ﬁeld.

8. Tighten all lens locking screws.

NOTE:

When tightening the lens locking screws, do not over-turn or force any screw.

Auto iris only:

Remove the ND ﬁlter.

10. If necessary, disable AGC:

a. Display the EXPOSURE SETTINGS menu.

b. Change AGC to OFF.

c. Select EXIT to save the AGC setting.

11.

Auto iris only:

Adjustment

Perform the auto iris lens adjustment procedure (refer to

in the Installation/Operation manual for more information).

Auto Iris Lens

12. As soon as you ﬁnish customizing this and all other camera settings, save your custom settings into the CUSTOM proﬁle. This protects them in case the camera loses power or must be restarted (refer to

Proﬁles

in the Installation/Operation manual for more information).

REVISION HISTORY

Manual # Date Comments

C2924M-QS 4/05 Original version.

Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com

USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150

International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120

C2924M-QS (4/05)