Peerless-AV ALU006009-AB, ALU009012-AW, ALU012018-AB, ALU012018-AW, ALU018024-AB Specsheet

Installation and Assembly:

Adjustable Extension Column 6" - 12'

Models:

ALU006009 (-AB) (-AW)

ALU009012 (-AB) (-AW)

ALU012018 (-AB) (-AW)

ALU018024 (-AB) (-AW)

ALU0203 (-AB) (-AW)

ALU0305 (-AB) (-AW)

ALU0406 (-AB) (-AW)

ALU0507 (-AB) (-AW)

ALU0608 (-AB) (-AW)

ALU0810 (-AB) (-AW)

ALU1012 (-AB) (-AW)

Max UL Load Capacity:

500 lbs (226.8 kg)

Note: The adjustable extension column should only be used with Peerless UL Listed products. The max load capacity for the combined assembly is not to exceed the lowest of all listed max load capacities.

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

•Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at

1-800-865-2112, for all international customers, please contact your local distributor.

•This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

•Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

•Never exceed the Maximum Load Capacity. See page one.

•Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

•Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

•This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

•When installing or adjusting the ceiling mount, do not use adhesives, lubricants, or oils to prevent the screws from loosening. If you use adhesives, lubricants, or oils to prevent the screws from loosening, the casing may crack and the projector may fall, causing serious injury and damage to the projector.

2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com

ISSUED: 12-05-11 SHEET #: 154-9015-1

Before you begin, make sure all parts shown are included with your product.

Parts List

	A	B	C	D
		extension	M8 x 10 mm	4 mm allen
Model	adjuster tube	pipe	screw	wrench
	Quantity 1	Quantity 1	Quantity 2	Quantity 1
ALU006009-AB	154-S1139	154-S1128	520-1706	560-9646
ALU009012-AB	154-S1139	154-S1137	520-1706	560-9646
ALU012018-AB	154-S1140	154-S1129	520-1706	560-9646
ALU018024-AB	154-S1140	154-S1130	520-1706	560-9646
ALU0203-AB	154-S1141	154-S1131	520-1706	560-9646
ALU0305-AB	154-S1142	154-S1132	520-1706	560-9646
ALU0406-AB	154-S1143	154-S1133	520-1706	560-9646
ALU0507-AB	154-S1143	154-S1138	520-1706	560-9646
ALU0608-AB	154-S1143	154-S1134	520-1706	560-9646
ALU0810-AB	154-S1143	154-S1135	520-1706	560-9646
ALU1012-AB	154-S1143	154-S1136	520-1706	560-9646
ALU006009-AW	154-S2139	154-S2128	520-2706	560-9646
ALU009012-AW	154-S2139	154-S2137	520-2706	560-9646
ALU012018-AW	154-S2140	154-S2129	520-2706	560-9646
ALU018024-AW	154-S2140	154-S2130	520-2706	560-9646
ALU0203-AW	154-S2141	154-S2131	520-2706	560-9646
ALU0305-AW	154-S2142	154-S2132	520-2706	560-9646
ALU0406-AW	154-S2143	154-S2133	520-2706	560-9646
ALU0507-AW	154-S2143	154-S2138	520-2706	560-9646
ALU0608-AW	154-S2143	154-S2134	520-2706	560-9646
ALU0810-AW	154-S2143	154-S2135	520-2706	560-9646
ALU1012-AW	154-S2143	154-S2136	520-2706	560-9646

Parts may appear slightly different than illustrated.

D

A

C

B

2 of 12

ISSUED: 10-26-11 SHEET NO: 154-9015-1

1

Note: Adjustable extension column should only be connected to UL Listed Peerless ceiling plates with 1 1/2"-11.5 NPT threading. See instructions provided with ceiling plate for additional assistance.

Thread adjuster tube (A) into bottom of threaded

fi tting on ceiling plate (sold separately) as shown in fi gure 1.1. Tighten adjuster tube so thread is securely engaged.

Align one small hole in the threaded fi tting of ceiling plate with slot of adjuster tube (A). Insert and tighten one M5 x 10 mm screw (not included) through the hole of threaded fi tting and slot of adjuster tube (A) as shown in figure 1.2.

WARNING

•Adjuster tube (A) must be fully threaded (six or seven full turns) onto threaded fi tting in ceiling plate and then locked with

M5 x 10 mm screw.

ceiling plate (sold separately)

1 1/2"-11.5 NPT threading

fig 1.1	A

M5 x 10mm screw (not included)

fig 1.2

2

Insert extension pipe (B) into adjuster tube (A) and secure with one screw (C). Adjust extension pipe to locate screw (C) into desired hook slot as shown in fi gure 2.1.

Insert second screw (C) through hole opposite of hook slot as shown in figure 2.2. Tighten both screws (C) using allen wrench (D).

Note: Only UL Listed Peerless components with

1 1/2"-11.5 NPT threading should be connected to the adjustable extension column.

To connect additional component to adjustable extension column see instructions provided with your component.

	A
	HOOK	C
	SLOTS
	C

B

fig 2.2

fig 2.1

3 of 12

ISSUED: 10-26-11 SHEET NO: 154-9015-1

4 of 12

Recommended Cleaning Guidelines

The following procedures are not guaranteed to control infection. An infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes.

Most painted components will withstand cleaning by commonly used, diluted, non-abrasive solutions such as quaternary ammonia compounds, ammonia enzyme cleaners, and bleach or alcohol solutions. However, it is recommended that any surface be tested in an inconspicuous area prior to determine the propensity for discoloration.

•Pen or permanent and dry erase markers can be removed with 91% isopropyl alcohol and a soft cloth.

•Iodine stains can be removed with commonly used cleaners and a soft cloth.

•Never use steel wool or other abrasive materials that will damage the surface fi nish.

•Do not use Acetone, mineral spirits, abrasive cleansers, paint thinner or any other harsh or toxic chemicals to clean your product. These solvents will damage the surface fi nish.

WARNING

•To avoid risk of electric shock, do not expose electrical components to water, cleaning solutions or other potentially corrosive liquids or substances.

•Do not use fl ammable cleaners on product surfaces due to close proximity of electrical power and equipment.

Peerless Industries, Inc.

2300 White Oak Circle Aurora, Il 60502 www.peerlessmounts.com

ISSUED: 10-26-11 SHEET NO: 154-9015-1 © 2011, Peerless Industries, Inc. All rights reserved.

All other brand and product names are trademarks or registered trademarks of their respective owners.