Partlow MIC 2000 Data Sheet

Data Sheet

Process Automation Worldwide Brands: LFE

TM

• Partlow

TM

• PMA

TM

• Rustrak

TM

• West

TM

MIC 2000

™

Versatile with High-End Features

APPLICATIONS:

Ideal for temperature control applications
requiring a value-priced, user-friendly, versatile
and full featured temperature controller.

INDUSTRIES:

• Industrial and lab ovens/furnaces, plastics and

thermal forming

• Form/Fill and seal

• Packaging applications

• And any others where low costs, smaller size

and unmatched connectivity are critical
requirements.

FEATURES/BENEFITS

• Single, 4-digit, 0.56” LED display

• 1/4 DIN panel mount

• Universal Input for thermocouple, RTD DC

linear V, DC linear mA/mV user-selectable

• Up to 3 outputs; relay, SSR driver, 4-20mA

• Process or deviation/band alarm functions

• ON/OFF, position proportioning, PID Control

• Optional RS-485 serial communications

• Program security

DESCRIPTION

The MIC 2000 is a single loop, 1/4 DIN controller
capable of controlling a variety of processes
ranging from simple on/off to dual 4-20mA output
with full PID. Inputs include thermocouple, RTD,
millivolt, volt, and milliamp.

Standard features include: isolated process
input, setpoint and output limits, and .56 inch high
LEDs. It will display programming of process
deviation and setpoint, of percent output, and
scaling with decimal point positioning.

Optional features include: up to three relay
outputs, three types of alarms, remote setpoint
input, electric motor modulation, RS-485
communications and process value
retransmission output as well as restricted
security access. Access to configuration
parameters and setpoint may be restricted by
using the instrument's security-access mode.

1/4 DIN Temperature Controller

Controllers

Process Automation Worldwide Brands: LFE

TM

• Partlow

TM

• PMA

TM

• Rustrak

TM

• West

TM

MIC 2000

™

Versatile with High-End Features

1/4 DIN Temperature Controller

SPECIFICATIONS*

DISPLAY

Digital Display: Four 7 segment LEDs each

.56 inches high. Status Indicators
Individual LED indictors for Setpoint, Out
1, Out 2, Manual, Alarm, Degrees F,
Degrees C, or Engineering Units, and
minus sign for negative values.

ALARM ADJUSTMENT

Process Alarm: -9999 to 9999 units
Deviation Alarm: -3000 to 3000 units
Deviation Band Alarm: 1 to 3000 units

CONTROL ADJUSTMENTS

On/Off Hysteresis: 0 to 300 units
Proportional Band: 1 to 3000 units
Manual Reset: -1500 to 1500 units
Auto Reset: 0.0 to 100.0 repeats/minute
Rate: 0.0 to 10.0 minutes
Cycle Time: 1 to 240 seconds
Position Prop. Sensitivity: 0.0 to 50.0%
First Output Position: -1000 to 1000 units
Spread: -1000 to 1000 units

(Second Output Position)

STANDARD FEATURES

Full PID capability
Single or dual outputs via relay, 4-20 mA

current or SSR driver
Separate alarm output
Universal input plus remote setpoint and

sensor break detection

ENVIRONMENTAL CHARACTERISTICS

Operating Temperature: 0 to 55°C, 32 to

131°F

Storage Temperature: -40 to 65°C, -40 to

149°F

Humidity: 0 to 90% RH, non condensing
Vibration: 0.5 to 100Hz at 0.5g

ELECTRICAL

Line Voltage: 115/230VAC +/- 10% 50/60 Hz
Power Consumption: 15VA maximum
Transmitter Power Supply: Provides up to

40mA @ 24 VDC.

INPUTS

Thermocouple types: J, K, T, R, S, E, B, N,

and C.

RTD: 100 ohm platinum (.00385

Ohm/Ohm/C)

Volts: 0 to 5VDC, 1 to 5 VDC
Millivolts: 0 to 25mVDC, 0 to 50mVDC, 10

to 50mVDC

Milliamps: 0 to 20 or 4 to 20mADC,

accommodated via the addition of a shunt
resistor

Remote Setpoint: 0 to 5VDC, 1 to 5 VDC
Sensor Fault Detection: Displays Hi or Lo

for thermocouple or RTD inputs (10%
above or below range) and sensor break,
SnSr. On/Off outputs go off, proportional
outputs go to 0%. Sensor fault detection
is not functional for 0 to 5VDC or 0 to
20mADC.

OUTPUTS

Relay: SPST

115VAC: 5.0 A Resistive; 1/8HP or 250VA
230VAC: 2.5 A Resistive; 1/8HP or 250VA

SSR Driver: Open collector output Short

circuit protected at 100mA maximum
Provides 4VDC at 20mA or 3VDC at 40mA

Current Output: 0-20 or 4-20 mADC into 650

ohms maximum

PERFORMANCE

Measurement Error Limit:

• Type J, K, T, E, N, C thermocouples and RTD
+/- 0.25% of reading plus 1 degree at 25°C

• Type R, S, B thermocouple +/- 0.25% of span
at 25°C

• mVDC, mADC and VDC +/- 0.25% of span,
plus 1 least-significent-digit at 25°C

Ambient Temperature Error: 0.01% of span per

degree C deviation from 25°C

Scan Rate: 1 scan per second (3 scans per

second available on EA option)

Display Resolution: T/C & RTD: 0.1 or 1 degree

mV & VDC: 0.001, 0.01, 0.1, or 1.0

Auto Reset Windup Inhibit: Auto reset is

disabled when the process is outside of the
proportional band

Cold Junction Compensation: Self compensation

for ambient temperature. All calibration values
are stored in memory.

Noise Rejection: Normal mode, 85dB minimum

@ 60Hz or greater. Common mode, 90dB
minimum ±8 VDC maximum peak for RTD
input, 115VAC maximum for other inputs.

PHYSICAL DIMENSIONS

Dimensions: 1/4 DIN front panel, 5.8" deep
Weight: 3 pounds maximum

COMMUNICATIONS

Type: RS-485 serial communication port
Protocol: Partlow ASCII

RATINGS/AGENCY APPROVALS

UL & cUL recognized (E67237),
CSA (LR39885)

WARRANTY

3 years
Made in USA

* Specifications are for base models with standard features

only unless otherwise noted. Specifications subject to
change without notice in accordance with our DBS policy
of continuous improvement. All product and brand names
are trademarks of their respective owners. All rights
reserved.

Partlow™ brand and MIC 2000™ are trademarks of Danaher Industrial
Controls Group. All rights reserved.

© 2005 DICG Corp.
Partlow Brand MIC 2000 Data Sheet (7/05)

Controllers