Panasonic WV-CW474AFE, WV-CW470AS User Manual

1. Camera Identification (CAMERA ID) Setting

You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID

consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on

the monitor screen.

To edit the CAMERA ID

1. Move the cursor to CAMERA ID.

The factory default setting is OFF.

2. Press

I(S). The CAMERA ID menu appears.

The cursor on the letter “0” is highlighted.

3. Move the cursor to the character you want to edit

by pressing

I(L) / I(R) / I(U) / I(D).

4. After selecting the character, press

I(S). The

selected character appears in the editing area.

(The pointer in the editing area moves to the right

automatically at this moment.)

5. Repeat the steps above until all characters are

edited.

To enter a blank space in the CAMERA ID

Move the cursor to SPACE and press I(S).

To replace a specific character in the CAMERA ID

1. Move the cursor to the editing area by pressing I(D).

2. Move the pointer to the character to be replaced by pressing

I(L) or I(R). Then move the

cursor to the character area and select a new character.

3. Press

I(S) to determine the CAMERA ID.

To erase all characters in the editing area

Move the cursor to RESET and press I(S). All characters in the editing area disappear.

To determine the display position of the CAMERA ID

1. Move the cursor to POSI, and press I(S). The display at right appears and the CAMERA ID is

highlighted.

2. Move the CAMERA ID to the desired position by

pressing

I(L) / I(R) / I(U) / I(D).

3. Press

I(S) to fix the position of the CAMERA

ID. The mode returns to the previous CAMERA ID

menu.

Notes:

• The CAMERA ID stops at the edges of the

monitor screen.

• The CAMERA ID moves faster if any of

I(L) / I(R) / I(U) / I(D) is kept pressed

for a second or more.

2. Light Control Setting (ALC)

2-1. ALC Mode with SUPER-D2 ON

Super Dynamic2 Function (SUPER-D2)

The important object in a scene is usually placed in the center of the monitor screen. In the SUPER-

D2 mode, more photometric weight is given to the center of the screen (where the important object

is located) than to the edge of the screen (where a bright backlight would most likely be located).

The SUPER-D2 function eliminates interference by strong background lighting which makes the

camera picture dark, such as a spotlight.

1. Move the cursor to ALC and press

I(S). The ALC CONT menu appears.

2. Move the cursor to SUPER-D2 and select ON.

3. If you want to adjust the video output level,

move the "I" cursor for LEVEL. Adjust to the

desired level by pressing

I(L) or I(R).

(To be continued reverse page)

SETTING PROCEDURES

** ALC CONT **

BACK LIGHT COMP

SUPER-D2 ON

LEVEL ..I......

- +

RET END

WV-CW474A

Highlighted

0123456789

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

().,'":;&#!?=

+-*/%$ДЬЦЖСЕ

SPACE

POSI RET END RESET

................

Character Cursor

Pointer

Character

Area

Command

Editing

Area

CAMERA ID menu

Caution:

Connect to 12 V DC (10.5 - 16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Make

sure to connect the grounding lead to the GND terminal when the power is supplied from a

24 V AC power source.

q Panning table

Adjusts the panning angle of the camera.

w Pan lock screw

Fixes the panning position.

e Tilting lock screw

Fixes the tilting position.

r AZIMUTH (Angle adjuster)

Shoots in a straight-angle field of view when aiming at an object in a slanting direction even if

the tilt angle has been set.

t Zoom lock lever

Fixes the zoom position.

y Focus lock lever

Fixes the focus position.

u LEFT button (I) (L)

Moves the cursor to the left, selects the mode and adjusts some levels.

i RIGHT button (I) (R)

Moves the cursor to the right, selects the mode and adjusts some levels.

o UP button (I) (U)

Moves the cursor upward and selects items in the CAM SET UP menu.

!0 DOWN button (I) (D)

Moves the cursor downward and selects items in the CAM SET UP menu.

!1 SET button (I) (S)

Activates an item selected in the CAM SET UP menu.

!2 BW AUTO1 LEVEL switch (SW5)

Selects the illuminance level in LOW or HIGH mode for B/W. The factory default setting is HIGH.

!3 BW switch (SW4)

Switches to AUTO1 between colour and black-and-white picture in response to light input. The

factory default setting is OFF.

!4 AP gain switch (SW3)

Selects the aperture gain level to SHARP or SOFT. The factory default setting is SHARP.

!5 UPSIDE DOWN switch (SW2)

Turns the picture upside down by selecting ON. The factory default setting is OFF.

!6 Sync switch (SW1)

Switches internal sync (INT) mode or line-lock (LL) mode. The factory default setting is INT.

LL: Line-lock mode is driven by 24 V AC or 220 V - 240 V AC.

!7 Monitor output Jack (3.5 mm in Diam. mini jack)

Connects the LCD monitor and such devices with 3.5 mm in diam. 2-pole L-type plug for check-

ing images.

!8 Optional heater connector DC out

When an optional heater unit is installed in the camera, the harness exiting from the unit will be

connected to this.

Brown

Blue

Green/yellow

Black

Grey

!9-1

!9-2

!9-3

!9-1Camera power cable for WV-CW474AFE (24 V AC 50 Hz or 12 V DC)

1. CAMERA SETUP MENU

This camera utilizes an on-screen user setup menu.

• Opening the Setup Menu

Press and hold down I(S) for 2 seconds or

more.

The CAM SET UP menu appears on the monitor as

shown at right.

Check the current settings on the menu.

Refer to the following sections for a detailed description of menu items. If you decide not to make

any changes after checking the current settings, move the cursor to END in the bottom line, and

press

I(S) to close the setup menu.

Note: If no button is pressed for 6 minutes while a setup menu is being displayed on the monitor

screen, it is automatically closed and the mode returns to the normal camera picture.

2. SETUP OPERATION

This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM SET

UP menu, use the following buttons on the SW board.

Left Button

(I) (L): Moves the cursor to the left. Use this button to select or adjust the parame-

ters of the selected item. The parameter changes each time this button is

pressed.

Right Button

(I) (R): Moves the cursor to the right. Use this button to select or adjust the para-

meters of the selected item. The parameter changes each time this button

is pressed.

Up Button

(I) (U): Moves the cursor upwards. Use this button to select an item or adjust the

parameters.

Down Button

(I) (D): Moves the cursor downwards. Use this button to select an item or adjust

the parameters.

Set Button

(I) (S): Executes selections and displays a submenu for an item with the mark.

•To reset the parameter to the factory default setting, move the cursor to the parameter to be

reset and press

I(L) and I(R) simultaneously.

• To return to the previous menu or page, move the cursor to RET and press

I(S).

• To close the setup menu, move the cursor to END and press

I(S).

• All Reset Operation

All Reset allows you to reset all setup menu items to the factory default settings if you are unsure

about the correct settings. Proceed as follows:

(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).

(2) While pressing both

I(L) and I(R), press I(S) for a few seconds. The message ALL

RESET momentarily appears on the monitor screen.

This resets all adjustments and parameters to the factory default settings except for the PIX

OFF setting.

• Editing the CAM SET UP Menu

Important Notice:

When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot

change the currently active settings. This is to prevent accidental changing of the settings.

To edit the CAM SET UP menu (change settings), press

I(U) and I(D) or I(L) and I(R) to

move the cursor to SET UP DISABLE in the bottom line.

Press

I(S). SETUP DISABLE changes to

SETUP ENABLE. Move the cursor to DIP SW.

Press

I(S). DIP SW changes to MENU. Then

move the cursor to the item(s) you want to

change.

Notes:

•When DIP SW is selected for CAM SET UP

menu, five modes can be set with the DIP

switches.

• To operate the camera functions with the system controller, select MENU in the CAM SET UP

menu.

Important Notice:

When the setup menu is closed after changing the parameters in the menu, the new values are

stored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). These

values remain valid until new values are stored, even if the power of the camera is off.

↵

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL ATW1

MOTION DET OFF

DIP SW

END SET UP DISABLE

↵↵↵

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL ATW1

MOTION DET OFF

END SET UP ENABLE

↵↵

↵

SETUP

↵↵

↵

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL ATW1

MOTION DET OFF

DIP SW

END SET UP DISABLE

1. The following functions are built in.

(1) Auto Light Control (ALC)

(2) The SUPER-D

2 function eliminates interference by strong background lighting which

makes the camera picture dark, such as a spotlight.

Dynamic range of 48 dB (Typ)

(3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync

(4) Auto/Manual White Balance Function

(5) Electronic Shutter Function

2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)

3. Minimum illumination of 2.0 lx (0.20 footcandle) (WIDE) (Colour mode)

Minimum illumination of 0.2 lx (0.02 footcandle) (WIDE) (Black-and-white mode)

Minimum illumination of 0.8 lx (0.08 footcandle) (WIDE) with the WV-CW2SE optional dome

cover (Colour mode)

Minimum illumination of 0.1 lx (0.01 footcandle) (WIDE) with the WV-CW2SE optional dome

cover (Black-and-white )

4. 480 lines of horizontal resolution (Colour normal mode)

510 lines of horizontal resolution (Colour High Resolution mode)

570 lines of horizontal resolution (Black-and-white mode)

5. High quality picture:

(a) 2H type vertical enhancer for greater picture sharpness

(b) Chroma averaging circuit for better colour signal-to-noise ratio

(d) Expanded dynamic range by use of knee circuit

(e) Highlight aperture correction for greater picture detail of bright objects

6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF

7. Built-in Digital Motion Detector

8. Auto black-and-white mode enables the camera to switch between colour and black-and-white

picture in response to Light input.

9. Electronic zoom function magnifies a scene 2-fold and changes the angle of view.

FEATURES

1. Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws or covers.

There are no user-serviceable parts inside. Ask qualified service personnel for servicing.

2. Handle the camera with care.

Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by

improper handling or storage.

3. The installation should be made by qualified service personnel or system installers.

4. Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a mild

detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.

5. Clean the lens with care.

Do not clean the lens with strong or abrasive detergents. Use lens tissue or a cotton tipped

applicator and ethanol.

PRECAUTIONS

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

N0304-0 3TR002452AAA Printed in Japan

Panasonic's WV-CW474AF/CW470AS series colour digital camera introduces a new level of high

picture quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensor

having 752 horizontal pixels (picture elements), and digital signal processing LSIs. This model

offers cutting-edge technology for advanced video surveillance.

PREFACE

Colour CCTV Cameras

Operating Instructions

Remove: Transport protection screw (Red)

Space for heater unit

Remove: Transport protection screw (Red)

EFT

OWN

SET

IGHT

LOW

HIGH

OFF

AUTO1

SHARP

SOFT

OFF

INT

Model Nos. WV-CW474AFE

WV-CW470AS

!9-3Camera power cable for WV-CW470AS (220 V - 240 V AC 50 Hz)

Caution:

Connect to 24 V AC (19.5 V-28 V) class 2 power supply only.

@0 Video output cable with BNC connector

Connects with the video connector of the monitor.

Caution:

Before attempting to connect or operate this

product, please read the marking on the top.

The serial number of this product may be found on

the top of the unit.

You should note the serial number of this unit in the

space provided and retain this instruction as a per-

manent record of your purchase to aid identification

in the event of theft.

Model No.

Serial No.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SER-

VICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT

CAREFULLY.

WARNING: This apparatus must be earthed.

IMPORTANT

The wires in this mains lead are coloured in accordance with the

following code.

Green-and-yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this appliance

may not correspond with the coloured markings identifying the ter-

minals in your plug, proceed as follows.

The wire which is coloured

green-and-yellow must be con-

nected to the terminal in the plug which is marked with the letter

or by the earth symbol I or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the ter-

minal in the plug which is marked with the letter

N or coloured

black.

The wire which is coloured brown must be connected to the

terminal in the plug which is marked with the letter

L or coloured

red.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and mainte-

nance (servicing) instructions in the

literature accompanying the appli-

ance.

The lightning flash with arrowhead

symbol, within an equilateral trian-

gle, is interned to alert the user to

the presence of uninsulated "dan-

gerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

Vi deklarerar härmed värt fulla ansvar för att den produkt till

vilken denna deklaration hänvisar är i överensstämmelse med

standarddokument, eller andra normativa dokument som

framstölls i Direktiv 73/23/EEC och 89/ 336/EEC.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä

ilmoitus koskee, noudattaa seuraavia standardeja tai muita

ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC

ia 89/336/EEC. säädöksiä.

We declare under our sole responsibility that the product to

which this declaration relates is in conformity with the stan-

dards or other normative documents following the provisions of

Directives EEC/73/23 and EEC/89/336.

Wij verklaren als enige aansprakelijke, dat het product waarop

deze verklaring betrekking heeft, voldoet aan de volgende

normen of andere normatiefve dokumenten, overeenkomstig

de bepalingen van Richtlijnen 73/23/ EEC en 89/336/EEC.

Vi erklærer os eneansvarlige for, at dette produkt, som denne

deklaration omhandler, er i overensstemmelse med den

følgende standarder eller andre normative dokumenter i følge

bestemmelserne i direktivene 73/23/ EEC og 89/336/EEC.

Vi erklærer oss alene ansvarlige for at produktet som denne

erklæringen gjelder for, er i overensstemmelse med følgende

normer eller andre normgivende dokumenter som fælger

bestemmelsene i direktiven 73/23/ EEC og 89/336/EEC.

Turn the power off at the mains to

disconnect the main power for all

unit.

WARNING: All work related to the installation of this product should be made by qualified service personnel or sys-

tem installers.

CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorpo-

rated in the electrical installation of the building.

6. Never face the camera towards the sun.

Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the

sun or other extremely bright objects. Otherwise, blooming or smear may be caused.

7. Do not operate the camera beyond the specified temperature, humidity or power source

ratings.

Use the camera at temperatures within –10 °C to +50 °C (–14°F - 122°F), and humidity below 90

%. The input power source for WV-CW474AFE is 24 V AC 50 Hz or 12 V DC and for WV-

CW470AS is 220 V - 240 V AC 50 Hz.

8. Turn the circuit breaker off which supplies the camera with the power when abnormal

conditions are encountered.

!99-2Power cable for heater unit WV-CW3HE (24 V AC 50 Hz) (applicable only to WV-

CW474AFE)

Caution:

Connect to 220 V - 240 V AC 50 Hz. The optional heater unit operates on 24 V AC that has

been supplied through the camera.

@1111 Dome cover

@2 Camera mounting bracket

The WV-CW470AS is supplied with a mounting bracket for ceiling installation.

@3 Camera attachment

@4 Cable access hole

@5 Sideway cable exit

The model shown is WV-CW474AFE.

Pick-up Device: 752 (H) x 582 (V) pixels, Interline Transfer CCD

Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-

up tube)

Scanning: 625 lines/50 fields/25 frames

Horizontal: 15.625 kHz

Vertical: 50.00 Hz

Synchronization: Internal, Line-locked or Multiplexed vertical drive (VD2) Sync

selectable

Video Output: 1.0 V[P-P] PAL composite 75 Ω/BNC connector

Horizontal Resolution: 480 lines (C/L Normal), 510 line (C/L, HIGH), 570 lines (B/W)

Signal-to-Noise Ratio: 50 dB (Equivalent to AGC Off, weight On, AP On)

Dynamic Range: 48 dB (Typ)

Minimum Illumination: 2.0 lx (0.20 footcandle) (WIDE) (C/L),

0.2 lx (0.02 footcandle) (WIDE) (B/W)

When the optional WV-CW2C dome cover is installed.

0.8 lx (0.08 footcandle) (WIDE) (C/L),

0.1 lx (0.01 footcandle) (WIDE) (B/W)

Gain Control: ON (HIGH, MID, LOW)/OFF selectable

White Balance: ATW1, ATW2 or AWC (SET UP MENU) selectable

Aperture: Set Variable (SET UP MENU)

Super Dynamic

2:ON or OFF (SET UP MENU) selectable

Electronic Shutter Speed: OFF, 1/120, 1/250, 1/500, 1/1 000,1/2 000,

1/4 000, 1/10 000 s selectable

Lens

Focal length: 3.8 mm - 8 mm

Maximum aperture ratio: 1:1.4 (Wide), 1:1.8 (Tele)

Angular field of view: Horizontal: 35.6 ˚ - 73.6 ˚

Vertical: 26.6 ˚ - 53.4 ˚

Focusing range: 1.2 m - ∞ (3.9 ft - ∞)

Ambient Operating Temperature: –10°C - +50 °C (–14 °F - 122°F)

Ambient Operating Humidity: Less than 90 %

Power Source and

Power Consumption: WV-CW474AFE: 24 V AC 50 Hz 3.8 W (camera),

12 V DC 367 mA (camera)

12.1 W (optional heater unit)

WV-CW470AS: 220 V - 240 V AC 50 Hz

5.2 W (camera)

14 W (with heater unit)

Dimensions: WV-CW474AFE: 160.5 mm (H) x 154 mm (D)

6-5/16” (H) x 6-1/16” (D)

WV-CW470AS: 161 mm (H) x 160 mm (D)

6-3/8” (H) x 6-5/16” (D)

Weights: WV-CW474AF: 1.45 k

g (3.2 lbs.)

WV-CW470AS: 2.15 k

g (4.7 lbs.)

Weights and dimensions indicated are approximate.

Specifications are subject to change without notice.

SPECIFICATIONS

OPTIONAL ACCESSORIES

STANDARD ACCESSORIES

Operating Instructions (this document) ............................................. 1 pc.

Instructions ........................................................................................ 1 pc.

The following are for installation.

Tamperproof screw bit ...................................................................... 1 pc.

Camera mounting bracket (supplied only to WV-CW470AS)............. 1 pc.

Camera fixing screw (supplied only to WV-CW470AS) ..................... 4 pcs.

Heater unit ......................................................................................... WV-CW3HE

Smoke dome cover ........................................................................... WV-CW2SE

Matsushita Electric Industrial Co., Ltd.

Osaka, Japan

http://www.panasonic.co.jp/global/

•PIX OFF Setting (PIX OFF)

In this setting, you can assign a blemish position and compensate the blemish.

1. Move the cursor to PIX OFF and press

I(S). The PIX OFF menu appears.

2. Select a number and press

I(S). The blemish compensation position setting screen appears.

Press

I(L), I(R), I(U) or I(D) to place the "+" cursor on the blemish position. After

moving the "+" cursor to a position where the blemish looks inconspicuous, press

I(S).

Consequently, the blemish compensation position is set up and the PIX OFF menu is restored.

After a blemish compensation position is set up, "*" is attached at the right of the number.

3. If you would like to delete a blemish compensation position, move the cursor to the applicable

number and press

I(S).

The blemish compensation position setting screen appears, and press

I(L) and I(R)

simultaneously for 2 seconds or more.

The screen is restored to the PIX OFF menu, the blemish compensation position is deleted and

"*" is also deleted from the right of the number.

** PIX OFF **

1* 2* 3* 4*

5* 6* 7* 8

000 000

RET END

4. When you want to adjust the white balance

manually, press

I(R) to select AWC and

press

I(S). The AWC menu appears on the

monitor screen. (When ATW is selected, press-

ing

I(S) displays the ATW menu.)

Manual Fine Adjustment for AWC/ATW

You can set the white balance items manually.

1. Move the cursor to R.

2. Press

I(L) or I(R) to obtain the optimum amount of red gain.

3. Move the cursor to B.

4. Press

I(L) or I(R) to obtain the optimum amount of blue gain.

8. Motion Detector Setting (MOTION DET)

The motion detector detects the moving objects in the scene by monitoring changes in brightness

level. You can select the level of sensitivity for motion detection.

When this camera is connected to a compatible intelligent CCTV system, the camera transmits an

alarm signal by multiplexing it with the video signal.

1. Move the cursor to MOTION DET and select

ON.

The factory default setting is OFF.

2. Press

I(S). The MOTION DETECT menu

appears on the monitor screen.

3. Move the cursor to MASK SET and press

I(S). MASK SET lets you set 48 mask areas. To set

MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2 OFF”.

4. Move the cursor to ALARM and select ON or OFF to set the alarm for DISPLAY MODE.

Note: When using the WV-RM70, WV-CU550C series, WV-CU161C or WV-CU360C controller

with this model, select OFF for ALARM.

5. Move the cursor to DISPLAY MODE and press

I(S) to see the current setting. The masks

that detect the brightness changes start blinking.

6. To raise detection sensitivity, press

I(S) to return to the MOTION DETECT menu.

7. To obtain the optimum detection level, move the “I” cursor to adjust the level.

8. Repeat the procedures above to obtain a satisfactory setting.

Notes:

• Masking or adjusting the detection level is needed to prevent malfunction under the following

conditions:

• When shooting an object under flickering fluorescent light.

• When leaves or curtains etc. are swayed by the wind.

• When the object is lighted by lighting equipment that constantly turns on and off.

• It takes about 0.2 seconds for the alarm signal to reach the alarm terminal of the VTR after the

camera detects the object.

Because the alarm signal is multiplexed on the video signal, it may be mistakenly interpreted

by other video equipment as a time code signal.

Therefore, when the camera is not used in a Panasonic Intelligent CCTV System, select OFF to

prevent the above from occurring.

• The camera will deactivate the detector for a few minutes after the power of the camera is

turned on or the BW setting in the Special Menu is set to something other than OFF.

• The motion detection function is not designed specifically for prevention of theft, fire, etc.

9. Special Menu

This menu lets you adjust and set up the video

signal of the camera to meet your require-

ments.

Move the cursor to END in the bottom line of

the CAM SET UP menu and press

I(L) and

I(R) simultaneously (holding down I(L)

and press

I(R)) for 2 seconds or more. The

SPECIAL menu appears on the monitor screen.

9-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)

1. Move the cursor to UP SIDE DOWN.

2. Select ON when you want to turn the picture upside down.

9-2. Chroma Level Setting (CHROMA GAIN)

1. Move the cursor to CHROMA GAIN.

2. While observing the vectorscope or colour video monitor, move the “I” cursor to adjust the

chroma level.

9-3. Aperture Gain Setting (AP SHARP/AP SOFT)

1. Move the cursor to AP SHARP.

2. To select AP SOFT, press

I(S).

3. While observing the waveform monitor or colour video monitor, move the “I” cursor to adjust the

aperture gain level.

9-4. Pedestal Level Setting (PEDESTAL)

1. Move the cursor to PEDESTAL.

2. While observing the waveform monitor or colour video monitor, move the “I” cursor to adjust the

pedestal level (black level).

** MOTION DETECT **

LEVEL ........I

- +

DISPLAY MODE

ALARM OFF

MASK SET

RET END

↵

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL ATW1

MOTION DET OFF

END SET UP ENABLE

↵↵

↵

↵↵

** SPECIAL **

UP SIDE DOWN OFF

CHROMA GAIN -....I....+

AP SHARP -...I.....+

PEDESTAL -......I..+

RESOLUTION NORMAL

EL-ZOOM OFF

BW MODE

PIX OFF

CAMERA RESET PUSH SW

RET END

9-5. Resolution Setting

1. Move the cursor to RESOLUTION.

2. For high resolution display, select HIGH.

NORMAL: Sets the horizontal resolution to more than 480 lines.

HIGH: Sets the horizontal resolution to more than 510 lines.

Note: After selecting HIGH, noise may increase when the SENS UP function is activated under

low illumination.

9-6. Electronic Zoom (EL-ZOOM)

1. Move the cursor to EL-ZOOM.

2. Select ON or OFF using

I(L) or I(R).

The factory default setting is OFF.

ON: x2 electronic zoom is available.

OFF: The electronic zoom function is disabled.

3. While the cursor is on EL-ZOOM, press

I(S).

The EL-ZOOM setting menu appears.

4. Move the cursor to PUSH SET for ZOOM and

press

I(S) to display the ZOOM setting

menu.

5. Press

I(U) or I(D) to zoom in or out the

image.

6. Move the cursor to PUSH SET for PAN/TILT

and press

I(S). The PAN/TILT setting menu

appears.

7. Press

I(U) or I(D) I(L) or I(R) to

change the angular field of view.

8. To return to the EL-ZOOM setting menu, press

I(S).

9-7. Black and White Mode (BW MODE)

Move the cursor to BW MODE and press I(S). The BW MODE menu appears. You can set

up the BW mode on this menu.

BW Setting

1. Move the cursor to BW and select AUTO1, 2,

ON or OFF using

I(L) or I(R). Factory

default setting: OFF.

AUTO1: The camera selects black and white

mode if the picture is dark, or colour mode

if the picture is bright enough.

AUTO2: Applying AUTO1 may cause malfunc-

tion when using a source of near-infrared

light at night because the illuminance

changes significantly when switching between the colour picture and a black-and-white

picture. This can be prevented by using the AUTO2 setting to detect the type of light

source.

Notes:

• Because the type of light source is detected based on information received from the

CCD image pickup element, an object that is constantly moving or has the same

colour as its background may not always be properly recognized. When choosing the

AUTO2 mode, make sure to use a light source having a wavelength of 800 nm or

more.

• The object may be out of focus when using a source of near-infrared light than using

the visible light.

ON: The black and white mode is selected.

OFF: The colour mode is selected.

2. If you have selected AUTO1, 2 the LEVEL and the DURATION TIME appear on the menu.

3. Select HIGH or LOW for the threshold level at which the camera automatically switches to BW

or colour mode. Default: HIGH

The illuminance shown below is based on the assumption that the camera is used in an area lit

by halogen lamps, and that AGC on the menu is set to MID.

Note: When near-infrared lamps are used, the image may be displayed out of focus and mode

switching may not perform automatically.

4. Move the I cursor to set DURATION TIME. Default: 30 seconds

The camera determines whether to switch the mode when the time set for holding a picture

motionless on the screen has elapsed.

Available duration times: (S) 10 s ↔ 30 s ↔ 60 s ↔ 300 s (L)

9-8. PIX SENS UP Setting

Move the cursor to PIX SENS UP and select

OFF or X2 AUTO.

X2 AUTO: Sensitivity will be automatically doubled at the maximum in the black and white

mode.

OFF: Sensitivity will not be enhanced.

Notes:

• "X2 AUTO" is not available when AGC is set to OFF. "X2 AUTO" is automatically set to OFF.

• When the picture becomes stable, the luminance may change for a moment.

9-9. BURST (BW) Setting

Move the cursor to BURST (BW) and select ON or OFF. Default: ON.

ON: The burst signal is supplied along with the black and white composite video.

OFF: The burst signal is not output.

Notes:

• Selecting ON is recommended for usual cases including when synchronizing the camera

to peripheral components.

• When storing images to a recorder, try both ON and OFF, then select either one suitable

for the recorder. Synchronization characteristics depend on the recorder.

To reset to the factory settings (CAMERA RESET)

1. Move the cursor to CAMERA RESET. The PUSH SW is highlighted.

2. While holding down

I(L) and I(R), press I(S) for 2 seconds or more. The camera is

reset to the factory settings except for PIX OFF setting.

** EL-ZOOM **

PAN/TILT →PUSH SET

ZOOM →PUSH SET

U TILT D/L PAN R

RET END

** EL-ZOOM **

PAN/TILT →PUSH SET

ZOOM →PUSH SET

U ZOOM D

RET END

The preset values for SENS UP (electronic sensitivity enhancement) change by pressing I(L) or

I(R) as shown right:

Notes:

• When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item.

• When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has priority

so that the SUPER-D2 function is not activated automatically.

• While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in

the picture when the sensitivity of the camera is increased. This is a normal phenomenon.

6. Synchronization Setting (SYNC)

You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed vertical

drive signal) mode.

Important Notices:

1. The priority for the sync modes is as follows:

(1) Multiplexed Vertical Drive (VD2) (Highest priority)

(2) Line-lock (LL)

(3) Internal Sync (INT) (Lowest priority)

2. The line-lock mode has a submenu for line-lock vertical phase adjustment. If the camera instal-

lation is relocated, check the vertical phase adjustment again since the AC line phase may be

different.

6-1. Line-lock Sync Mode (LL)

1. Move the cursor to SYNC and select LL.

Note: The settings in this menu can be made

only when the multiplexed vertical drive

signal (VD2) is not supplied to the camera.

2. After confirming that the cursor is on LL, press

I(S). The vertical phase adjustment menu

appears on the monitor screen.

3. Supply the video output signal of the camera

to be adjusted and the reference camera video

output signal to a dual-trace oscilloscope.

4. Set the oscilloscope to the vertical rate and expand the vertical sync portion on the oscillo-

scope.

5. Move the cursor to COARSE. The cursor is

highlighted.

6. Press

I(L) or I(R) to match the vertical

phase for both video output signals as closely

as possible. (COARSE adjustment can be

incremented in 16 steps by 22.5 degrees by

pressing

I(L) or I(R).)

Note: After the sixteenth step, the adjustment

returns to the first step.

7. Move the cursor to FINE.

8. Press

I(L) or I(R) to match the vertical phase for both video output signals as closely as

possible.

(FINE adjustment can be made by up to 22.5 degrees by pressing

I(L) or I(R).)

Notes:

• When the “I” cursor reaches the “+” end, it jumps back to “–”. At the same time, COARSE

is incremented by one step to enable a continuous adjustment. The reverse takes place

when the “I” cursor reaches the “–” end.

• When

I(L) or I(R) is kept pressed for a second or more, the “I” cursor moves faster.

• To reset COARSE and FINE to the values preset at the factory, press

I(L) and I(R)

simultaneously. COARSE and FINE adjustments are preset at the factory to zero-crossing

of the AC line phase.

• If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of the

camera video output signal may be disturbed.

• This mode functions only when unit operates on AC power.

7. White Balance Setting (WHITE BAL)

7-1. Auto-Tracing White Balance Mode (ATW)

You can select one of three modes for white balance adjustment as follows:

The factory default setting is ATW1.

•ATW1 (Auto-Tracing White Balance 1)

Move the cursor to WHITE BAL and select ATW1.

In this mode, the colour temperature is monitored continuously and thereby white balance is

automatically set. The colour temperature range for the proper white balance is approximately

2 600 - 6 000K. Proper white balance may not be obtained under the following conditions:

1. The colour temperature is out of the 2 600

- 6 000K range.

2. When the scene contains mostly high

colour temperature objects, such as a

blue sky or sunset.

3. When the scene is dim.

In these cases, select the AWC mode.

•ATW2 (Auto-Tracing White Balance 2)

Auto-tracing white balance in sodium light

mode (ATW2)

When that you select ATW2 for sodium light, white balance is set automatically (no operation

needed).

Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup menu.

• Automatic White Balance Control Mode (AWC)

In this mode, accurate white balance is obtained within a colour temperature range of approxi-

mately 2 300-10 000K.

1. Move the cursor to WHITE BAL and select

AWC

→ PUSH SW.

2. Press

I(S) to start the white balance setup.

The PUSH SW is highlighted to indicate that

the white balance is being set.

3. When the white balance setting is completed,

the PUSH SW returns to normal display.

Note: If white balance is not set, the PUSH SW

is being highlighted.

2-2. ALC Mode with SUPER-D2 OFF

1. Move the cursor to SUPER-D2 and select OFF.

The MASK SET appears on the menu.

2. Move the cursor to MASK SET and press

I(S). The 48 mask areas appear on the

monitor screen. The cursor is blinking in the

upper left corner of the screen.

3. Move the cursor to the area where backlight is

bright and press

I(S) to mask that area. The

mask turns to white. (When the cursor is

moved on an area that has already been

masked, the mask and cursor start blinking.)

4. Repeat step 3 to mask the desired area. To

cancel masking, move the cursor to that area

and press

I(S).

5. After masking is completed, press

I(S) for 2

seconds or more. The ALC CONT menu

appears.

6. If you want to change the video output level

(picture contrast), move the “I” cursor for

LEVEL and adjust the level.

Note: If ON is selected for SUPER-D2, a shadow

(black line) may appear at the boundary

between the bright and the dim scene. This is

a natural phenomenon and does not indicate trouble.

3. Shutter Speed Setting (SHUTTER)

Note: To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu.

Move the cursor to SHUTTER and select the electronic shutter speed.

The preset values for SHUTTER (electronic shutter speed) change by pressing

I(L) or I(R) as

follows:

The factory default setting is ---.

Note: When SUPER D2 is set to ON, a dotted line appears for the shutter speed, and you cannot

select it.

4. Gain Control Setting

You can set the gain (brightness level portion of an image) to automatic level adjustment.

Move the cursor to AGC and select automatic level adjustment [AGC ON (LOW, MID, HIGH)/OFF

(fixed level)].

• Gain Control [AGC ON (LOW/ MID/ HIGH)/OFF]

Move the cursor to AGC and select ON (LOW),

ON (MID), ON (HIGH) or OFF.

The factory default setting is ON (HIGH).

Note: Even if AGC is set to ON and if the noise reduction function is enabled, afterimages may

be produced by shooting a moving object.

•Digital Noise Reduction (DNR)

DNR may be used to improve quality under low light conditions. There are 2 levels of DNR,

which may be selected depending on local site conditions.

You may need to try different settings to find

the most suitable conditions for your applica-

tion.

Move the cursor to DNR and select LOW or

HIGH.

LOW: DNR level is low.

HIGH: DNR level is high.

The factory default setting is HIGH.

5. Electronic Sensitivity Enhancement (SENS UP)

There are two modes for SENS UP.

AUTO: If you select X10 AUTO, for example, the sensitivity is automatically raised to X10 max.

When AUTO is selected, AGC is automatically set to ON.

FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32.

The factory default setting is OFF.

Move the cursor to SENS UP and select the parameter for electronic sensitivity enhancement.

SETTING PROCEDURES

1 (1 - - 16): 0 degrees

2 (1 - - 16): 22.5 degrees

16 (1 - - 16): 337.5 degrees

** SYNC **

V PHASE

COARSE 1(1--16)

FINE I........

- +

RET END

X2 AUTO

OFF

X4 AUTO X6 AUTO X10 AUTO

X32 FIX X10 FIX X6 FIX X4 FIX X2 FIX

OFF

X16 FIX

** ALC CONT **

BACK LIGHT COMP

SUPER-D2 OFF

MASK SET

LEVEL ..I......

- +

RET END

↵

OFF 1/120

1/10000 1/4000 1/2000 1/1000

1/250 1/500

** AWC **

R ....I....

- +

B ....I....

- +

RET END

Blinking

Turns to white

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL AWC

→

PUSH SW

MOTION DET OFF

END SET UP ENABLE

↵↵

↵

Highlighted

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL ATW1

MOTION DET OFF

END SET UP ENABLE

↵

↵↵

** CAM SET UP **

CAMERA ID OFF

ALC ALC

SHUTTER ---

AGC ON(HIGH)

SENS UP OFF

SYNC INT

WHITE BAL ATW1

MOTION DET OFF

END SET UP ENABLE

↵

↵↵

** AGC **

DNR HIGH

RET END

** BW MODE **

BW OFF

PIX SENS UP OFF

BURST(BW) ON

RET END

** BW MODE **

BW AUTO1

LEVEL HIGH

DURATION TIME •

••

S L

PIX SENS UP OFF

BURST(BW) ON

RET END