Panasonic WJ-HD316, WJ-HDE300 Maintenance Manual
Digital Disk Recorder Extension Unit
WJ-HDE
3
0
0
Extension Unit
WJ-HDE300 S-ATA conversion guide
1. Sept. 2008
Panasonic System Solutions
WJ-HDE300 S-ATA conversion guide
Maintenance guide
1. Outline
This guide describes how to convert the hard disk drive installed in the WJ-HDE300 from the P-ATA type to the S-ATA type.
2. Preparation
(1) Screwdriver
(2) Wrench for hexagonal nut (5.5m/m)
(3) S-ATA conversion kit (0E0A0028AA)
Part name Part number Quantity
S-ATA Board Ass’y JHE30JKY3A 2
K1V313Y10002 (S-ATA: Gray, Power cable: Red/Yellow)
S-ATA cables
S-ATA board mounting hardware 3CA005880AAA 1
Insulating plate 3CZ001284AAA 1
Hexagonal spacer 22 mm 1CJ001328AAA 1
Hexagonal spacer 7 mm 1CJ001311AAA 6
Cord clamp FCA16 9
S-ATA label, small (for front) 3PD003840AAA 1
S-ATA label, large (for top) 3PD003841AAA 1
SW label 3PD003124CAA 1
S-ATA leaet 3TU001944AAA 1
Hexagonal spacer 6mm (for HDE350) 1CJ001309AAA 1
Additional screws - 5
(4) 2 Cable ties
(5) Ruler
(6) S-ATA HDD (
GB) x quantity (part number:
***
K1V313Y10003 (S-ATA: Gray, Power cable: White/Orange)
K1V313Y10004 (S-ATA: Red, Power cable: Red/Blue)
K1V313Y10005 (S-ATA: Red, Power cable: White/Purple)
********
)
1 each
Panasonic System Solutions
1
HDE300_SATAConversionGuide_B
WJ-HDE300 S-ATA conversion guide
Maintenance guide
3. Replacement Procedure
Important +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
• Before touching the HDD, eliminate static electricity accumulating in your body.
• Ensure that the HDD is protected against static charge by placing disks on a antistatic mat or a conductive bag during the conversion work.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
(1) Remove two screws xing the front panel.
Front Panel
(2) Slide the front panel to the left.
(3) Pull the both sides of the front panel toward you.
(4) Disconnect the connector of the cable coming out of the front panel.
(3)
(2)
(3)
Panasonic System Solutions
2
HDE300_SATAConversionGuide_B
WJ-HDE300 S-ATA conversion guide
HDD #2
HDD #1
HDD #4
HDD #3
Important ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
The HDDs should be installed in the correct positions in the
order as shown right. Do not skip a drive position or reverse
the order of the HDD positions. Incorrectly placed drives will
result in the recorder not recognizing the extension unit or the
drives.
HDD #1 slot : HDD1 HDD #2 slot : HDD2
HDD #3 slot : HDD3 HDD #4 slot : HDD4
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
(5) Remove six screws xing the metal plate and then remove
the metal plate.
Maintenance guide
Inside the front cover
(6) Disconnect four ATA cables and four HDD power cables
of all HDDs.
When disconnecting the ATA cables, pull the pull-ring
Note:
slowly and straightforward.
(7) Remove four screws xing the HDD mounting bracket,
pull out the bracket.
Metal plate
Pull-ring
HDD mount bracket
Panasonic System Solutions
3
HDE300_SATAConversionGuide_B
Loading...