Panasonic TY-WK42PR2W User Manual

Plasma display wall-hanging bracket
(Adjustable angle type)

Fitting Instructions

Before commencing work, carefully read these Instructions and the Manual
for the wide plasma display to ensure that fitting is performed correctly.
(Please save these instructions. You may need them when maintaining or moving the bracket.)

Wandhalterung zum Anbringen des Plasmadisplays
(Typ mit einstellbarem Winkel)

Anleitung zur Anbringung

Vor der Ausführung lesen Sie bitte diese Anleitung und die Bedienungsanleitung für
das Plasmadisplay sorgfältig durch, damit die Anbringung richtig ausgeführt wird.
(Bitte bewahren Sie diese Anleitung auf. Sie kann bei der Wartung oder der
erneuten Anbringung der Halterung benötigt werden.)

Muurbevestigingssteun voor plasmascherm
(met verstelbare montagehoek)

Montage-instructies

Lees deze installatiehandleiding en de bedieningshandleiding voor het breedbeeld-plasmascherm
zorgvuldig door voordat u begint, zodat de montagewerkzaamheden op de juiste wijze worden uitgevoerd.
(Bewaar deze handleiding. U hebt de handleiding weer nodig wanneer u de
bevestigingssteun verwijdert of verplaatst.)

Staffa per montaggio alla parete dello schermo al plasma
(con angolazione regolabile)

Istruzioni per il montaggio

Prima di iniziare il montaggio leggere attentamente queste istruzioni ed il manuale
dello schermo al plasma allargato per poter procedere al montaggio in modo corretto.
(Conservare poi queste istruzioni che si renderanno necessarie per la
manutenzione e l’eventuale spostamento della staffa.)

Applique de fixation au mur
(Type à angle réglable)

Instructions de montage

Avant de commencer le travail, lisez attentivement ces instructions ainsi que le mode
d'emploi de l'écran large à plasma de manière à réaliser un montage convenable.
(Conservez soigneusement les présentes instructions. Vous pouvez en avoir
besoin pour effectuer un entretien ou si vous désirez déplacer l'applique.)

Soporte para colgar la pantalla de plasma en una
pared (Tipo de ángulo ajustable)

Instrucciones de instalación

Antes de empezar el trabajo, lea atentamente estas instrucciones y el manual
de la pantalla panorámica de plasma para asegurar una instalación correcta.
(Guarde estas instrucciones. Podrá necesitarlas cuando haga trabajos de
mantenimiento o mueva el soporte.)

Väggupphängningshållare för plasmaskärm
(vinklingsbar typ)

Monteringsanvisningar

Innan arbetet påbörjas ska du noga läsa dessa anvisningar och bruksanvisningen
som medföljer plasmaskärmen för att försäkra att arbetet utförs på rätt sätt.
(Bevara dessa anvisningar. Du kan behöva anlita dem på nytt för underhåll
eller flyttning av hållaren.)

Vægophæng til plasmaskærm
(justerbar vinkeltype)

Opsætningsinstruktioner

Før arbejdet påbegyndes, skal De omhyggeligt læse disse instruktioner og betjeningsvejledningen
til widescreen-plasmaskærmen for at sikre at opsætningsarbejdet udføres korrekt.
(Gen disse instruktioner. De kan få brug for dem ved vedligeholdelse, eller
hvis ophænget skal flyttes.)

TY-WK42PR2W

Model No.

English

Deutsch

Nederlands

Italiano

Français

Español

Svenska

Dansk

TQZH545

English

22

English

2

WARNING

Fitting work and connection equipment expansion should never be done by any other
than a qualified installation specialist.

• Incorrect fitting may cause equipment to fall, resulting in injury.

Include a safety factor when considering the strength of the proposed fitting location.

• If strength is not sufficient the equipment may fall, resulting in injury.

Do not fit at a location that cannot bear the load.

• If the fitting location lacks sufficient strength the equipment may fall.

CAUTION

Do not fit at any locations subject to humidity, dust, smoke, steam or heat.

• This may have an adverse effect on the plasma TV and cause fire or electric shock.

The work of fitting or removing the plasma TV must be performed by at least two people.

• The plasma TV may fall and cause injury.

Do not fit facing upwards, sideways or upside down.

• This may cause heat to build up inside the plasma TV unit, resulting in a fire.

Ensure there is a space of at least 100mm at the top, bottom and sides of the plasma TV,
and at least 89 mm clearance at the back.

• The plasma TV unit has air blow holes on the top, and air suction holes on the bottom and rear.
Covering these may result in a fire.

1) Exercise care when selecting the location for the TV because it may discolor or deform due to light or heat if it
is placed where it is exposed to direct sunlight, or near a heater.

2) Upkeep
Wipe with a dry cloth. If the unit is extremely soiled, first wipe off soiling with a neutral detergent diluted in
water, and then wipe with a dry cloth. Do not use cleaners such as benzene, thinner or furniture wax because
they may cause paint peeling. (If using a chemical wiping cloth, follow any precautions included.)

3) Do not affix adhesive tape or stickers to the product. Either may stain the wall hanging bracket or surface of the
wiring cover for close-to-the-wall installation.

Requests regarding handling

Safety precautions

[Always follow these precautions]

3

English

Components

Wall-hanging bracket . . . x1

Insulation spacers . . . x4

Dished toothed washers . . . x4

Allen wrench (included tool)

. . . x1

Unit fastening screws
( M5-35) . . . x2

Allen head countersunk screws
(M8-50) . . . x4

TY-WK42PR2W Wall-hanging bracket (Adjustable angle type)

Precautions for wall-hanging bracket fitting

♦ The wall-hanging bracket is for use in attaching a plasma TV unit to a vertical wall for viewing. Do not fit to

any surface other than a vertical wall.

♦ To ensure correct plasma TV performance and prevent trouble, do not fit at any of the following locations.

• Near sprinklers or fire/smoke detectors

• Where there is a risk of exposure to vibration or impact

• Near high-voltage wires or dynamic power supplies

• Locations exposed to air blown from heating equipment

♦ Fit using techniques suited to the structure and materials of the fitting location.
♦ Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc.)

for fitting the bracket to the wall.

♦ Fit so there is no contact between the attachment screws or power cord and any metal inside the wall.
♦ For the TV power supply plug, use a power supply outlet that can be reached easily.
♦ Ensure good air flow so that the equipment ambient temperature does not exceed 40°C. Failure to do this

may cause heat to build up inside the plasma TV, resulting in malfunction.