Panasonic TY-SP42PWD3W, TY-CE42PS1, TY-ST42PW1, TY-SP42PM3W, TY-ST42PT3S User Manual

Pedestal

TY-ST42PT3S TY-ST42PT3K

Wall stand

TY-ST42PW1

Mobile stand

TY-ST42PF3

Wall-hanging bracket (vertical)

TY-WK42PV1

Wall-hanging bracket (angled)

TY-WK42PR1

Ceiling unit

TY-CE42PS1

Speakers

TY-SP42PM3W TY-SP42PWD3W

How to use this manual

Some notes on how to read this manual

In this manual, the number such as "1, 2, 3,..." appears to the left of each step.
Go ahead in numerical order.

Indicates a situation where incorrect handling may result in death or serious injury for the person performing the
installation.

Indicates a situation where incorrect handling may result in breakdown or damage to physical objects.

Contains more detailed information than in the steps in the main text. Be sure to read the notes.

Other notes

• More-detailed explanations and supplemental information for the installation procedures are given on the right.
* Be sure to read not just the steps on the left, but the information on the right as well.

• At the very beginning of the installation procedure, there are illustrations for assembling various accessory parts
on the Wide Plasma Display. Refer to them when installing.

• Each installation procedure for accessory parts is preceded by a brief description of the procedure. During the
pro-cedure, refer to the description if necessary.

• Each installation procedure for accessory parts is followed by an explanation of how to remove the Wide Plasma
Display. Refer to this when it is necessary to remove the accessory parts from the Wide Plasma Display and reposition
it.

Before installing

Be sure to read through these instructions before starting the installation.

The installation should be only performed by a professional person.
If any parts are not installed correctly, the display unit may fall, possibly resulting in damage and personal injury.

Failure to follow Warning instructions may result in damage and personal injury.

Make sure that all safety conditions regarding strength at installation are observed.

If the installation strength is insufficient, the display unit may fall and personal injury may result.

Do not install in places which are unable to bear the weight of the display.

If the strength of the floor and wall at the site of installation is insufficient, the display unit may fall, possibly
resulting in damage and personal injury.

A caution indicates special precautions against actions which may result in fire or electric shock.

Do not install in places subject to humidity, dust, oil fumes, condensation or excessive heat.

These factors may adversely affect the Wide Plasma Display, possibly resulting in fire or electric shock.

Do not install the Wide Plasma Display horizontally with the screen facing up, or sideways or upside
down.

Installing the screen other than in the conventional viewing setting may cause heat to build up inside the display
and possibly result in fire.

Two persons are required to install and remove the display unit.

The display unit is heavy and at least two persons are needed to handle it safely. The display unit may drop and
personal injury may result if one person attempts to install it without assistance.

Maintain a space of at least 10 cm respectively at the top, bottom and sides of the display unit and at
least 1.9 cm at the rear of the display unit.

The display unit has air outlet holes at the top and air intake holes at the bottom and rear. These holes must not
be blocked, nor airflow not be obstructed. Otherwise fire may result.

Tools list

The tools in the following tables are necessary for complete assembly.
Before attempting to install the accessories, make sure you have the following tools on hand.

Plus screw driver Clean cloth Drill Measure Level gauge

Pedestal

Wall stand

Mobile stand

Wall-hanging
bracket (vertical)

Wall-hanging
bracket (angled)

Ceiling unit

Optional parts list

Wire or Chain M6 bolt x 6

–––

–––

Pedestal

Wall stand

Mobile stand

Wall-hanging
bracket (vertical)

Wall-hanging
bracket (angled)

Ceiling unit

–

–

–

–

–

–

Accessory list

1

Pedestal

TY-ST42PT3-S
TY-ST42PT3-K

2

Wall stand

4

Wall-hanging bracket (vertical)

TY-WK42PV1

5

Wall-hanging bracket (angled)

3

Mobile stand

TY-ST42PW1

6

Ceiling unit

7

Speakers

TY-WK42PR1

TY-CE42PS1

TY-ST42PF3

For information on the wiring of the Wide Plasma Display after installing accessories, be sure to refer to the

documentation that comes with the Wide Plasma Display.

TY-SP42PM3W

TY-SP42PWD3W

Parts list

Check the part number before performing the installation procedure.

Pedestal

Base Assembly screw(M5-20) x 4

Assembly screw (M5-30) x 4

Band x 2

Pole x 2

Black screw x 2

Wall stand

Wall pedestal

Wood screw x 2

Black screw x 2

Clamp x 4

Allen key (accessory) Fixing screw (M5) x 2

Holding bracket

Pan head bolt with hex socket

(M8-45) x 4

Insulating spacer x 4

Toothed pan washer x 4 Fixing screw (M5) x 2 Assembly

Mobile stand

Holder Shelf Stand base Support x 2

Cable strap x 5 Bolt (M8)x 4

Assembly screw (M5-15) x 4 Assembly screw (M5-30) x 4

Wall-hanging bracket ( vertical )

Wall-hanging bracket unit Fixing screw (M5) x 2

Pan head bolt with hex socket (M8-45) x 4

Tooted pan

washer x 4

Insulating

Assembly screw (M6-16)
and spring washer x 4 each

Allen key (accessory)

spacer x 4

Wall-hanging bracket ( angled )

Wall-hanging bracket unit Fixing screw (M5-35) x 2

Pan head bolt with hex socket (M8-45) x 4

Tooted pan

washer x 4

Insulating

spacer x 4

Allen key (accessory)

Ceiling unit

Ceiling unit Fixing bolt (M8-12) x 2

(M8-45) x 4

Toothed pan washer x 4

Insulating spacer x 4

Allen key

Fixing bolt (M8-100)

Spring washer

Washer pan nut (M8)

Fixing screw (M5) x 2

Fixing bolt (M8-20) x 2

Cable tie x 2 Pan head bolt with hex socket

Speakers

Speaker x 2

Mounting bracket

(right) x 2

Mounting bracket

(left) x 2

Bracket mounting
Assembly screw (M4-10) x 12

Sponge x 2

Speaker cable

(20 cm) x 2

Points to note during installation

This ceiling unit is for mounting a Wide Plasma Display to a ceiling for viewing purposes.

•

Do not use it for any type of installation other than ceiling mounting.

In order to ensure correct, problem-free operation of the Wide Plasma Display, do not install the Display in any of

•

the following places:

• Next to sprinklers or sensors

• Where it may be subject to vibration or shocks

• Near high-voltage wires or electric motors

• Where it may be in direct contact with air from heaters

When installing this ceiling unit, use a fixing method appropriate to the type of ceiling.

•

Insert the mains plug for the Wide Plasma Display into a mains socket which is close and easily accessible.

•

Provide adequate ventilation so that the temperature around the display does not rise above 40°C (104 F°).

•

If there is insufficient movement of the air inside the displa y, heat may build up inside the display and fire ma y result.

For U.S.A (TH-42PW3 / TH-42PWD3 only)

•

If the connection cable cannot reach the Display when it has been installed to the wall, use the 15 m cable (TY­SCP15C03) which is sold separately.

Dimensions of the display unit

Units : mm

1020

50

4646

920

50

518

610

489

98

112.2 65390.9

L

22

S-VIDEO

18.5

AUDIO AUDIO

VIDEO

AV IN

VD HD P

R

18 18 18 18 20 53.86

35.7

R/CR/R PB/CB/B Y/G

70.69 296

89

44

615

L

R

AUDIO

PC INCOMPONENT/RGB IN

SERIALTUNER IN

39.43

To connect the power cord and others, refer to the documentation that comes with the Wide Plasma Display.

Assembly diagram

Pedestal

TY-ST42PT3S
TY-ST42PT3K

CONTENTS

Instruction of the installation...................... 1-2

1.Assembling the pedestal

2.Attaching the pedestal to the display unit

3.Fixing the display unit

.................................... 1-2

.............. 1-2

....................................... 1-3

1-1

Instruction of the installation

Assembling the pedestal

Put the poles into the outer holes on the base, and fasten the four

1

screws.

Ensure that the poles sit
flush with the bottom of
the base.

Assembly screw

(M5-20) x 4

Attaching the pedestal to the display unit

Spread a clean cloth over a le vel floor or base, and place on it the display

1

unit face down.
Remove the screws and covers.
Keep them in a safe place for possible future use.

Place the display face
down on a cloth clean
and free from other
foregin particles, and
then proceed to the next
step.

1-2

Insert the two poles at the top of the pedestal into the holes in the base

2

of the display unit as shown in the illustration below.
Insert the four screws, two on each side, into the holes in the back

3

of the display unit and screw them into the holes on the inserted poles.

Front

Rear

Fixing the display unit

Fixing the display unit to a desk.

Assembly screw

(M5-30) x 4

Band x 2

Screw the bands to the pedestal with screws.

1

Screw the bands to edge of a desk with screws.

2

Black screw x 2

Wood screw x 2

If you are using a
wooden desk, then use
the wood screws.
Use the appropriate
screws for the type of
material of the desk.

1-3

Fixing the display unit to the wall

Insert the screws and clamp into the holes at the back of the display

1

unit.

Use a strong wire or chain commercially available to fix the display unit

2

to a solid area of the wall or pillar.

Black screw x 2

Clamp x 4

1-4

Assembly diagram

Wall stand

TY-ST42PW1

CONTENTS

Description ................................................... 2-2

Instruction of the installation...................... 2-3

1.Assembling the wall stand

2.Fixing the insulating spacers to the display unit

3.Attaching the wall stand to the display unit

4.Fixing the display unit to the wall

Removing the display unit........................... 2-8

.................................. 2-3

...... 2-4

............ 2-6

......................... 2-7

2-1

Description

Installation diagram

Units : mm

)

4

/

3

1020 (40

5

744 (2919/64)

560 (22

390 (15

1

/16)

23

/32)

/64)

3

/4)

19 (

89 (333/64)

*100

)

64

/

1

400 (15

)

64

/

5

610 (24

)

64

/

61

1116.5 (43

611.5 (24

* A clearance of at least 100mm at the top of the display unit should be provided.

2-2

Instruction of the installation

Assembling the wall stand

Check the strength of the installation location.

1

The height measurements marked ** are particularly important. Do not
attempt to set up the pedestal in a location where these dimensions and a
clearance of at least 100 mm at the top of the display unit should be provided.

1) On the wall, measure and mark a height 650 mm above the floor;

2) Measure and mark the location 475 mm horizontally to the right of
the mark you made in 1). Measure and mark points 180 mm and 360
mm above each mark (for a total of six marked locations);

3) Drill a hole at each of the six marked locations on the wall.

Units : mm

744 (2919/64)
560 (22 1/16)

390 (1523/64)

/32)

3

Refer to the holding
bracket installation
measurements in the
drawing left. Ensure that
the wall is able to bear
the weight at each of the
4 upper and lower
installation locations.
Add reinforcement if any
of these locations are
not strong enough.

Ensure an area of at least
650 mm by 1,230 mm in
length at the location
where you plan to install
the holding bracket.

180 (7
/32)

3

180 (7

/8)

7

631.5 (24



**

Wall installation holes
(4 locations)

Spare wall installation holes
(2 locations)

Floor surface

/4)

3

400 (15

/16)

1

611.5 (24

**

The holding bracket has
6 slits through which the
bracket can be fixed to a
wall with screws.

If the wall material does
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
used at the place of
installation, cracks may
develop if the scre ws are
inserted too close to
each other.

2-3

Fix a M6 screw, through any of the slits in the bracket, into the

2

corresponding hole in the wall.

Using a level along the top or bottom edge, ensure that holding bracket is
horizontal.

The holding bracket must always be installed. It prevents the display unit from
falling after installation.

Fix the screws through the slits into the remaining three holes.

3

Provisionally tighten the fixing screws.

4

Fixing the insulating spacers to the display

unit

1) Spread a clean cloth over a level floor or base, and place it on the

1

display unit face down.

2) Remove the screws and covers.
Keep them in a safe place for possible future use.

If the screws protrude
more than 5 mm, it will
not be possible to
properly install the
display unit.

Carefully place the Wide
Plasma Display face
down on top of a clean
cloth, which has been
spread over a flat
surface with no other
objects on it, and then
proceed to the next
step.

2-4

Remove the four screws.

2

As shown in the illustration, use the supplied "Allen key" to fasten the

3

screw through

and , then screw the four to the display unit.

Pan head bolt with

hex socket
Toothed pan washer
Insulating spacer

2-5

Attaching the wall stand to the display unit

Insert the two poles at the top of the wall pedestal into the holes in the

1

base of the display unit as shown in the illustration.
Insert the four screws, two on either side, into the holes in the back

2

of the display unit and fasten them into the holes in the inserted poles.

The screws and covers
may be required later if
the display unit is moved
and mounted directly to
a wall, so keep them in
a safe place so that they
will not get lost.

Assembly screw

(M5-30) x 4

2-6

Fixing the display unit to the wall

Lift the display so that the upper insulating spacers at the back may fit

1

into the notched indentation at the top of the holding bracket, and then
lower the display into place.

1) Lift the display slightly and insert the lower insulating spacers at the

2

back of the display unit into the lower cutouts in the holding bracket.

2) Lower the display into the lower notched part of the cutouts.

Do not lift the display
too high or it may come
out of the notches in the
upper indentations.

Insert and fasten the screws at both the left and right sides.

3

Holding bracket

Fixing screws (left and right)

To prevent the display
unit from becoming
detached from the
holding bracket, make
sure that both the left
and right fixing screws
are properly fitted.

Fixing screw(M5)

2-7

Removing the display unit

Remove the two fixing screws from the sides of the holding bracket.

1

1) Lift the display slightly;

2

2) Pull the bottom half way to detach the lower insulating spacers;

3) Lift the display away from the holding bracket.

Insulating
spacer

Fixing screws
(left and right)

2)

3)

1)

Holding
bracket

2-8

Assembly diagram

Mobile stand

TY-ST42PF3

CONTENTS

Description ................................................... 3-2

Instruction of the installation...................... 3-3

1.Assembling the mobile stand

2.Fixing the display unit to the stand

3.Fixing the wiring

Removing the display unit........................... 3-6

............................................... 3-5

.............................. 3-3

....................... 3-4

3-1

Description

Installation diagram

Units : mm

1020 (40 5/32)

/64)

1

610 (24

/64)

29

89 (3

33

/64)

820 (32 5/16)

1637 (64

1030 (40 9/16) 650 (25

400 (15

19

/32)

3

/4)

15°

3-2

Instruction of the installation

Assembling the mobile stand

Insert the supprots into the slots on the upper side of stand base, and

1

then fix them from below using the four

Slide the shelf, with the supports in the slots, down to the required

2

height. Choose the locations of stopper holes to match the required
height. Then fix the shelf using the four

bolts.

screws and spring washers.

Front

When installing the stand,
provisionally fasten all
bolts and screws first,
and then fasten them to
complete the assembly.

Bolt (M8)

Support

1

2

Choose the locations of
the stopper holes to
match the required height.

1) height of 500 mm

2) height of 350 mm

Insert the holder into the supports, and fix it with the four screws.

3

Assembly screw (M6-16)
and spring washer x 4 each

Be sure to assemble on a
stable horizontal surface.

Assembly screw(M5-15)

3-3

Fixing the display unit to the stand

1) Spread a clean cloth over a level floor or base, and place on it the

1

2
3

display unit face down.

2) Remove the screws and covers.
Keep them in a safe place for possible future use.

Insert the two poles at the top of the stand into the holes in the base of
the display unit as shown in the illustration below.

Insert the four screws, two on each side, into the holes in the back of
the display unit and fasten them into the holes in the inserted poles.

Lock the casters before
installing the display unit.
Press down the caster
switch to lock the caster.

Unlock

Lock

Assembly screw (M5-30)

3-4

Fixing the wiring

Insert the accessrory cable straps, evenly spaced, into the appropiate

1

mounting holes in the rear of the support.

Cablestraps

Cable

Bring together the input cables which are connected to the terminals at

2

the bottom of the display unit and secure them with the five cable
straps.

To loosen cable straps:

1. Push the strap in the
direction of the arrow
in the diagram; and

2.Loosen the cable
strap by passing it
through the cramping
hole.

3-5

Removing the display unit

Loosen and remove the four screws from the display unit.

1

Lift the display unit away from the stand.

2

2

1

3-6

Wall-hanging bracket

Assembly diagram

(vertical)

TY-WK42PV1

CONTENTS

Description ................................................... 4-2

Instruction of the installation...................... 4-4

1.Fixing the wall-hanging bracket to the wall

2.Fixing the insulating spacers to the display unit

3.Attaching the display unit to
the wall-hanging bracket

Removing the display unit........................... 4-7

Warning......................................................... 4-8

................................ 4-6

............ 4-4

...... 4-5

4-1

Description

Installation diagram

Units : mm

930
660

450

490

20

55.5

450 450

900

1020

* A clearance of at least 100mm at the top of the display unit should be provided.

320

69.5

610

*100

89

19

4-2

Installation diagram
For Multi Screen

Units : mm

90

120

* Installe lower panel unit first.

4-3

Instruction of the installation

Fixing the wall-hanging bracket to the wall

Check the strength of the installation location

1

The wall-hanging bracket weighs approximately 6kg, and the display unit by
itself weighs 33kg. Refer to the wall-hanging bracket installation dimensions
in the diagram below to , check the strength of the wall in six installation locations ,
and add reinforcement if any of these locations are not strong enough.

1) Select an installation site with an area of at least 1,500 mm wide by
800 mm high. Refer to the figure to make a positioning mark for the
location of the center-top hole.

2) Measure and mark the locations 450 mm to the left and 450 mm
horizontally to the right of the location you marked in 1).

3) Measure and mark the locations 450 mm below each of the marked
location.

Units : mm

Used for routing wires behind a wall

15

2020

930

450450

The wall-hanging bracket
has installation holes
provided at 24 locations.

If the wall material does
not allow sufficient
strength by using six
installation holes, use
some of the spare
holes.
However, depending on
the construction
material used at the
place of installation,
cracks may develop if
the screws are inserted
too close to each other.

15

4-4

490

450

100 50

50

30

Wall installation holes(6 locations)

Insert and fasten a M6 screw bolt into the center-top hole.

2

Use a level gauge to correct the alignment of the wall-hanging bracket,

3

and screw bolts into the remaining five holes.

Provisionally tighten the fixing screws.

4

If required, use commer­cially available M6
bolts which suit the wall
materials.

If the Screws protrude
more than 5 mm, it will
not be possible to install
the Wide Plasma Display
in the correct position.

Fixing the insulating spacers to the display
unit

Spread a clean cloth over a le vel floor or base, and place on it the displa y

1

unit face down.
Remove the four screws from the display.

Use the accessory tool "Allen key" to install the four accessory ,

2

and into the holes.

Place the display unit
face down on top of a
cloth clean and free from
otherforegin particles,
and then proceed to the
next step.

Pan head bolt with

hex socket
Toothed pan washer
Insulating spacer

4-5

Attaching the display unit to the wall-

hanging bracket

Lift the display unit so that the upper insulating spacers at the back

1

may fit into the notched indentation at the top of the wall-hanging
bracket, and then lower the display unit into place.

1) Lift the display unit slightly and insert the lower insulating spacers

2

at the back of the display unit into the lower cutouts in the wall­hanging bracket.

2) Lower the display unit into the lower notched part of the cutouts.

Notches

Do not lift the display
too high or it may come
out of the notches in the
upper indentations.

Insultating spacer

Insert and fasten the screws at both the left and right sides.

3

Holding bracket

Fixing screws(left and right)

T o pre vent the display unit
from becoming detached
from the wall-hanging
bracket, make sure that
both the left and right
fixing screws are properly
fitted.

Fixing screw(M5)

4-6

Removing the display unit

Remove the two fixing screws from the sides of the wall-hanging

1

bracket.

1) Lift the display slightly;

2

2) At the same time, pull the bottom half way to detach the lo wer insulating
spacers;

3) Lift the display away from the wall-hanging bracket.

3)

Fixing srews
(left and right)

1)

lower insulating
spacer

2)

4-7

Warning

IF UN OFFICIAL BRACKET IS USED.

Do not fix. The display unit with un official bracket by bolts directly, the display unit
may damage and possibly electrical interfalance for other electronics equipment.

Pan head bolt with
hex socket

660

Toothed pan washer

Insultating spacer

320

Pan head bolt with

hex socket
Toothed pan washer
Insulating spacer

29

22

14

4-8

Wall-hanging bracket

Assembly diagram

(angled)

TY-WK42PR1

CONTENTS

Description ................................................... 5-2

Instruction of the installation...................... 5-3

1.Fixing the wall-hanging bracket to the wall

2.Adjusting the angle of the display fitting

3.Fixing the insulating spacers to the display unit

4.Attaching the display unit to
the wall-hanging bracket

Removing the display unit........................... 5-7

................................ 5-6

............ 5-3

................ 5-4

...... 5-5

5-1

Description

Installation diagram

Units : mm

45020

490

930
660

**310

*100

89

610

450 450

900

1020

* A clearance of at least 100mm at the top of the display unit should be provided.
** Installation of the wall-hanging bracket requires a depth of 310 mm.

5-2

Instruction of the installation

Fixing the wall-hanging bracket to the wall

Check the strength of the installation location

1

The wall-handing bracket weighs approximately 6kg, and the wide plasma
display unit by itself weighs 33kg. Refer to the wall-hanging bracket installation
dimensions in the diagram below to check the strength of the wall in six
installation locations, and add reinforcement if any of these locations are not
strong enough.
Further installation of the wall-hanging bracket requires a depth of 310 mm.

1) Select an installation site with an area of at least 1,500 mm wide by
800 mm high. Referring to the figure, make a positioning mark for
the location of the center-top hole;

2) Measure and mark the locations 450 mm to the left and 450 mm
horizontally to the right of the location you marked in 1);

3) Measure and mark the locations 450 mm below each of the marked
location.

The wall-hanging bracket
has installation holes
provided at 14 locations.

If the wall material does
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
at used at the place of
installation, cracks may
develop if screws are
inserted too close to
each other.

Units : mm

Used for routing wires behind a wall

15 15

490

450 2020

5030

Insert and fasten a M6 screw bolt into the center-top hole.

2

930

100 50

Wall installation holes(6 locations)

450450

If required, use
commercially available
M6 bolts which suit the
wall materials.

5-3

Use a level gauge to correct the alignment of the wall-hanging bracket,

3

and screw bolts into the remaining five holes.

Provisionally tighten the fixing screws.

4

After determining the positions and checking them against the bracket,
embed M6 bolts or nuts. Furthermore, when embedding the bolts, ensure
that the bolts protrude from the wall by 10 to 15 mm.

Adjusting the angle of the display fitting

If the screws protrude
more than 5 mm, it will
not be possible to install
the Wide Plasma Display
in the correct position.

The angle of the display fitting can be adjusted to one of the five positions
ranging from vertical to 20 tilt in 5 steps.

At the time of shipment, the angle of tilt is set to 5 from vertical. To change
this angle, adjust the position of the stay.

5 tilt 15 tilt No tilt

stay

The stay is not needed if
the display unit is to be
fixed vertically.

Angle adjustment positions

5tilt
10tilt

15tilt

20tilt
No tilt

5

10
15

20

0

5-4

Fixing the insulating spacers to the display

unit

Spread a clean cloth over a le vel floor or base, and place on it the display

1

unit face down.
Remove the four screws from the display.

Use the accessory tool "Allen key" to install the four accessory ,

2

and into the holes.

Place the display unit
face down on top of a
cloth clean and free from
otherforegin particles,
and then proceed to the
next step.

Pan head bolt with

hex socket
Toothed pan washer
Insulating spacer

5-5

Attaching the display unit to the wall­ hangingbracket

Lift the display unit so that the upper insulating spacers at the back

1

may fit into the notched indentation at the top of the wall-hanging
bracket, and then lower the display unit into place.

After that, lift the display unit slightly and insert the lower insulating

2

spacers at the back of the display unit into the lower cutouts in the
wall-hanging bracket.

Then lower the display unit into the lower notched part of the cutouts.

3

1

Do not lift the display
too high or it may come
out of the notches in the
upper indentations.

2

3

Fixing screws

Insulating spacer

Insert and fasten the screws at both the left and right sides.

4

Wall-hanging bracket

Fixing screws mounts

Fixing screws(left and right)

To prevent the display
unit from becoming
detached from the wall­hanging bracket, make
sure that the left and
right fixing screws are
properly fitted.

Fixing screw (M5-35)

5-6

Removing the display unit

Remove the two fixing screws from the sides of the wall-hanging

1

bracket.

1) Lift the display unit slightly;

2

2) At the same time, pull the bottom half way to detach the lo wer insulating
spacers;

3) Lift the display away from the wall-hanging bracket.

3)

Foxing screws
(left and right)

1)

Insulating spacer

2)

5-7

Assembly diagram

Celing unit

TY-CE42PS1

CONTENTS

Description ................................................... 6-2

Instruction of the installation...................... 6-3

1.Assembling the ceiling unit

2.Prepare the ceiling unit

3.Prepare the display

4.Mount the display in the ceiling unit

Removing the display unit........................... 6-8

........................................... 6-6

................................. 6-3

...................................... 6-4

..................... 6-7

6-1

Description

Installation diagram

Units : mm (in.)

89

Ceiling board

660

50

926

~

626

431

6-2

Instruction of the installation

Assembling the ceiling unit

Check the strength of the installation location.

1

This ceiling unit weighs approx. 19kg (41.9lbs).The display weights approx.
33kg (72.8lbs) to 45kg (99.2lbs). Refer to the diagram on the right and
confirm that the four points for mounting the ceiling unit and display are
capable of bearing this weight. If the installation location is not strong
enough to bear this weight, reinforce the ceiling before the ceiling unit and
display are installed.

Units : mm (in.)

Ceiling installation holes

14 (35/64)

)

16

/

15

24 (

)

32

/

9

R7

(R

Prepare the ceiling unit.

2

Remove the two Fixing bolts (M8-12) from the ceiling unit and separate the
upper and lower sections of the unit.

Ceiling unit
(lower section)

Front

Fixing bolt (M8-12)

350 (1325/32)
300 (1126/32)

Ceiling unit
(upper section)

)

32

/

26

300 (11

Fixing bolt (M8-12) x 2

6-3

Installation the ceiling unit.

Attach the ceiling unit (upper section)

1

1) Before installing the upper section, pull the wiring through the pipe.
Use an earthed mains extension lead (not supplied).

2) Make holes in the ceiling using a method appropriate for the ceiling
structure and for inserting M12mm bolts. Install the upper section
using a hex socket bolt (M12 not supplied), flat washer and spring
washer.

Flat washer
(not supplied)

Spring washer
(not supplied)

M12 bolt
(not supplied)

6-4

Signal cable
(example)

• Reinforce the ceiling if it is not strong enough.

• Use bolts appropriate for the ceiling material (not supplied).

• Refer to the installing examples for wooden structure and concrete structure.

Earthed mains extension lead
(example)

Installing to a concrete structure(example)Installing to a wooden structure(example)

Mounting plate

Ceiling board

9

/

16

Nut
Flat washer

" ] )(min.thickness 40mm [1

Flat washer
Spring washer

M12 bolt

Nail

Beam

Concrete

Anchor nut or
curled plug(M12)

Flat washer
Spring washer

M12 bolt

Attach the ceiling unit (lower section)

2

1) Match the height adjustment holes on the upper and lower sections
to the desired height and refasten in place with two M8 assembly
screws.

2) Insert the fixing bolt (M8-100) through the spring washer and then
insert it through the uppermost hole in the pipe. Fasten in place with
the washer pan nut (all included).

3) Tighten with two fixing bolts (M8-12, included) so that the lower
section does not move.

Fixing bolt (M8-100)

Ceiling unit
(upper section)

Washer pan nut

Fixing bolt (M8-12)

(Example)

Ceiling unit

Spring washer

Fixing bolt (M8-100)

Fixing bolt (M8-12)

White line

Fixing bolt
(M8-12)

Hidden
side

Spring washer

Washer pan nut (M8)

(lower section)

Fixing bolt (M8-12) x 2

When adjusting the height, no more that 4 holes should be visible. (The white line should not show.)

Distance from

Height adjustment
holes

center of display
to ceiling ( in.)

1085mm (42

23/32

)

Center of
display

985mm (38

885mm (34
785mm (30

25/32

27/32

29/32

)
)

)

6-5

Prepare the display.

Install the insulating spacers in the display unit.

1

1

Lay the display with the screen facing down on a clean blanket or sheet and
follow the steps below.

1) Remove the four bolts from the display.

2) In each of the four bolt holes, insert a pan head bolt with hex socket
(M8-45), toothed pan washer and insulating spacer (four each, all
included). Insert as shown in the diagram on the left.

Quite los cuatro pernos.

6-6

Pan head bolt with

hex socket

Toothed pan washer

Insulating spacer

Mount the display in the ceiling unit.

Hook the display’s top insulating spacers in the ceiling unit by aligning

1

the display with the notches in the ceiling unit and sliding the display
downward.

Insert the bottom insulating spacers by lifting the display slightly, fitting

2

the bottom spacers into the holes, and then lowering the display.

Insulating spacer

Notch

Notch

When mounting the
display in the ceiling unit,
be sure the ceiling unit is
straight and not at an
angle.

Do not lift the display too high. It may come unhooked from the unit.

Fix the display.

3

Install two fixing screws (M5, included) in the corresponding holes on the
ceiling unit (left and right).

Fixing screw (M5) 1 each
left and right sides

Fixing screw (M5) x 2

Install the fixing screws
on the left and right to
prevent the display from
sliding out of the ceiling
unit.

6-7

Adjust the ceiling unit's direction.

4

Adjust the angle of the display and fix in place with two fixing bolts (M8-20,
included).

Fixing bolt
(M8-20)

Adjust the ceiling unit's angle.

5

Fixing bolt (M8-20) x 2

This ceiling unit can be placed in 7 angles from 0° to 30° in 5° increments.
The factory setting is 0°.
If you wish to change the angle, remove the angle adjustment screws from
the connecting pipe and adjust the angle adjustment holes to the desired
position. Then reinsert the screws.

Connecting pipe

Angle
adjustment
hole positions

0° (vertical)

5°
10°
15°
20°
25°
30°

6-8

Gather the cables.

6

Gather the cables connected to the terminals on the back of the display and
fix in place with a cable tie.

Cable tie

Cable

Cable tie

Cable

Cable tie x 2

6-9

Removing the display unit

Remove the two fixing screws (M5) at the left and right sides of the

1

ceiling unit.

1) Lift the lower part of the display,

2

2) pull outward

3) and lift upward.

3)

1)

Fixing screw (M5)

2)

Insulating
spacer

6-10

Assembly diagram

Speakers

TY-SP42PM3W

TY-SP42PWD3W

CONTENTS

Description ................................................... 7-2

Safety Precautions....................................... 7-2

Instruction of the installation...................... 7-3

1.Attach the sponges to the speakers

2.Attach the mounting brackets to the speakers

3.Attach the speakers to the Wide Plasma Display

4.Secure the speakers in place

5.Connect the speaker cables

............................... 7-5

..................... 7-3

........ 7-3

.... 7-4

............................. 7-4

7-1

Description

Installation diagram

Units : mm (in.)

610

89

Left Speaker Right Speaker

89100

100

610

Safety Precautions

Do not suspend the speakers.

Personal injury may result if the speakers fall down. Take particular care to ensure the safety of children.

These speakers are for use with the Wide Plasma Display only.

If connecting them to some other amplifier, make sure that the maximum input to the speakers is within the rated
level (8 W). If the rated input level is exceeded, fire may result.

Make sure that all screws are tightened securely during installation.

Ensure that the installation is carried out property to prevent the speak ers from becoming detached, and causing
possible personal injury.

7-2

Instruction of the installation

Attach the sponges to the speakers.

• Attach the sponges to the surfaces which are in contact with the Display.

• Clean the surfaces before attaching the sponges.

Sponges

For right

Attach the mounting brackets to the speakers.

For left

Sponge x 2

Mounting brackets
(right)

Mounting brackets
(left)

Bracket mounting screws Bracket mounting screws

Speaker (right) Speaker (Ieft)

Mounting bracket

(right) x 2

Mounting bracket

(left) x 2

Bracket mounting
Assembly screw (M4-10) x 8

7-3

Attach the speakers to the Wide Plasma

Display.

• Insert the hooks on the top and bottom mounting brackets simultaneously
into the slots at the rear of the Wide Plasma Display, and then lower the
speaker into place.

• Attach the left speaker in the same way.

Slot

Slot

Hook

Rear of Wide Plasma Display

Secure the speakers in place.

• Adjust so that there is a uniform clearance between the Wide Plasma Displa y
and the speakers, and then securely tighten the bracket mounting screws.

• Secure the top and bottom mounting brackets by tightening the bracket
mounting screws.

• Secure the left speaker in the same way.

Bracket mounting
screw

Bracket mounting
Assembly screw (M4-10) x 8

7-4

Rear of Wide Plasma Display

Connect the speaker cables.

Preparing the ends of the
speaker cables

While twisting

• After preparing the ends of the speaker cables, connect them as shown.

• Connect the speaker cable for the left speaker in the same way.

• The red cab le is f or the (+) side and the blac k cable is for the (-) side. Do not
connect the cables to the wrong sides.

1.

Press down on the lever.

2. Insert
the cable.

3. Release the lever.

1. Push down the lever.

2. Insert
the cable.

3. Return the lever to its
normal position.

Speaker cable

(20 cm) x 2

1. If connecting to an external amplifier which exceeds the rated input for the speakers, lower the

2. Do not place the speakers in the following places:

3. This set is equipped with magnetic resistant speakers but be careful not to place them near the

4. To clean the speakers, wipe them with a soft cloth. If they are extremely dirty, wipe them with a

5. Remo ve the dust on the speaker net using a duster or a vacuum cleaner at low power. Since the

When these speakers are attached to the plasma display, they will not
form a straight line but rather so that the y slightly f ace inward, to produce
stable sounds.

amplifier volume to protect the speakers from damage. If an y problems occur with speaker operation,
disconnect the mains lead of the amplifier and consult a qualified service technician.

• Places which are exposed to direct sunlight

• Near heaters or other heat sources

• Places with high humidity

CRT TV as it may cause color patches.

cloth which has been soaked in a small amount of household detergent, and then wipe the dry
with a separate cloth.

• Do not use solvents such as alcohol or thinner.

• If using chemically-treated cloths, follow the instructions on the cloth packaging.

net is made of cloth, pushing too hard on it may damage the net.

7-5

Matsushita Electric Industrial Co., Ltd.

Central P.O. Box 288, Osaka 530-8692, Japan