Panasonic SVMP-805-VGC, SVMP-810-VGC Service manual

Digital Audio Player

SV-MP805VGC SV-MP805VGH SV-MP810VGC SV-MP810VGH

Colour

(W)................... White Type

(K).................... Black Type

TD0602002CE

Specifications

Memory size: SV-MP810V: 1 GB

SV-MP805V: 512 MB

Supported sampling frequency: MP3; 8 kHz to 48 kHz

WMA; 22.05 kHz, 32 kHz, 44.1

kHz and 48 kHz

Supported bit-rates: MP3; 8 kbps to 320 kbps (128

kbps is recommend)

WMA; 32 kbps to 192 kbps (96

kbps is recommend)

No. of channels: Stereo, 2 channels (MUSIC, FM

RADIO, LINE IN)

Mono, 1 channel (VOICE

RECORD)

Frequency response: 20 Hz to 20,000 Hz (+0 dB, -6 dB)

(MUSIC)

300 Hz to 4,300 Hz (VOICE

RECORD, 64 kbps)

Radio Frequency range (FM):

Input (LINE): -14dB(0.2mV),3.5mm

Output: 3mW+3mW(16Ω,3.5mm

87.90 MHz to 107.90 MHz (200 kHz steps)

87.50 MHz to 108.00 MHz (50/100 kHz steps)

stereo)

Power supply: DC 1.5V (one alkaline battery)

Approximate play times: 36 hours (MUSIC),

7 hours (FM RADIO)

Approximate recording times:

Dimensions (W x H x D):

Mass:

· Specifications are subject to change without notice.

· The play time shown depends on operating conditions.

· Mass and dimensions are approximate.

· GB means one billion bytes. MB means one million bytes. Usable

· This product supports the following character codes. The display

may not appear correctly with other character codes.

· The play time shown is when the bit rate is 128 kpbs (MP3), EQ

is set to NORMAL, volume is 11 and the backlight is not used.

13 hours (VOICE RECORD, 64

kbps), 7 hours (FM RADIO),12

hours (LINE IN, 128 kbps)

Maximum: 55.8 mm x 25.7 mm x

25.2 mm

Cabinet: 55.3 mm x 25.2 mm x

25.2 mm

34.3 g with battery

23.0 g without battery

capacity will be less

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

CONTENTS

Page Page

1 System requirements 2

1.1. Caution for maintainment

1.2. During the maintainment, the right of the song data of the

customer as below

2 Safety Precaution

2.1. Human body grounding

2.2. Work table grounding

3 Service Navigation

3.1. About Lead Free Solder (PbF)

4 Accessories

5 Location of Controls

6 Operation Checks and Component Replacement Procedures

6.1. Removal of the battery cover

6.2. Removal of the front cabinet

6.3. Removal of the Main P.C.B.

6.4. Removal of the Tuner P.C.B.

6.5. Removal of the LCD Ass'y

6.6. Removal of the REC Button

6.7. Removal of the Hold knob

6.8. Removal of the spring holder Ass'y

6.9. Removal of the battery spring and spring holder 8

7 Service Position

8 Service Mode

8.1. Update or install the firmware(When replace DSP IC and

Flash Memory IC, please re-install the firmware and font

table.)

8.2. Reset procedure

8.3. Checking the software version

9 Troubleshooting

10 Troubleshooting guide

11 Saving data

12 Type Illustration of ICs, Transistors and Diodes

13 Block Diagram

14 Schematic Diagram Notes

15 Schematic Diagram

16 Printed Circuit Board Diagram

17 Cabinet Parts Location

18 Packaging

19 Replacement Parts List

1 System requirements

1.1. Caution for maintainment

1. Please make a copy before maintainment.

2. When update the software, please re-install the firmware.

3. When replace DSP IC and Flash Memory, please re-install the firmware and font table.

2. The song that purchase from the web-site, the songs has been encoded but no limited for the time for using or the songe has not been encoded, the righ of customer will not be in fuenced.

1.2. During the maintainment, the right of the song data of the customer as below

1. When purchase the song from the web site, the songs has

been encoded or limited for the time for using.

The right of custermer will lose one time.

2 Safety Precaution

2.1. Human body grounding

Use the anti-static wrist strap to discharge the static electricity from your body.

2.2. Work table grounding

Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pick-up) is placed, and ground the sheet.

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

3 Service Navigation

3.1. About Lead Free Solder (PbF)

Distinction of PbF PCB:

PCBs (manufacture d) using lead free solder will have a PbF stamp on the PCB

Caution:

· Pb free solder has a higher melting point than standard solder, Typically the melting point is 30-40° C higher.

Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 370±10° C.

· Pb free solder will tend to splash when heated too high (about 600° C).

· W hen soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat

the soldering points with the Pb free solder until it melts enough.

4 Accessories

· USB Cable (with Line-in)

(K1HY08YY0002) ............................................................. 1pc.

· Strap Stereo earphones.................................................1pc.

(L0BAB0000205).........................................................(White)

(L0BAB0000207).........................................................(Black)

5 Location of Controls

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

Microphone

Skip/Search button

MODE button

Volume button

Display

Turn on, off / Play/Stop button

Basic playback operations

Display the main menu:

Press [ ]

MODE

USB port

REC/STOP, A-B REPEAT button

Earphones jack

(3.5 mm stereo)

Adjust the volume:

Press [

] or [ ] (0-25)

HOLD switch

Battery lid

Turn ON: Press [ Turn OFF: Press and hold [

"Good bye" is displayed, and the

unit's power is turned off.

The power cannot be turned off while the main menu is displayed.

Play/Stop: Press [ ]

When you next press [ ], play resumes from where you stopped it. (Resume)

]

Skip: Press [

[

Search: During play, press and

] (backward) or

] (forward)

hold [ or [

] (forward)

] (backward)

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

6 Operation Checks and

Component Replacement Procedures

1. This section describes procedures for checking the

operation of the major printed circuit boards and replacing the main components.

2. For reassembly after operation checks or replacement,

reverse the respective procedures special ressembly procedures are described only when required.

3. Select item from the following index when checks or

replacement are required.

Contents

1. Checking for the main P.C.B.

2. Checking for the memory P.C.B.

3. Checking for the LCD ass’y.

4. Checking for the prevent electrostatic discharge.

6.1. Removal of the battery cover

6.2. Removal of the front cabinet

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

6.3. Removal of the Main P.C.B.

6.5. Removal of the LCD Ass'y

6.4. Removal of the Tuner P.C.B.

6.6. Removal of the REC Button

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

6.7. Removal of the Hold knob

6.8. Removal of the spring holder Ass'y

6.9. Removal of the battery spring and spring holder

7 Service Position

SV-MP805VGC / SV-MP805V GH / SV-MP810V GC / SV-MP810VGH

+ 21 hidden pages