Panasonic SC-HTB8 User Manual

Owner’s Manual

Home Theater Audio System

Thank you for purchasing this product.
Please read these instructions carefully before using this product,
and save this manual for future use.

If you have any questions, visit:
U.S.A. : www.panasonic.com/support

Model No. SC-HTB8

Register online at www.panasonic.com/register

Included Installation Instructions

The installation work should be done by a qualified installation specialist. (> p. 10 to 14)

Before commencing work, carefully read these installation instructions and the operating instructions
to ensure that installation is performed correctly.
(Please keep these instructions. You may need them when maintaining or moving this unit.)

P

(U.S. customers only)

VQT5J41

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow the safety instructions on the
unit and the applicable safety instructions listed below. Keep these operating instructions handy for
future reference.

1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades
with one wider than the other.
A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong
are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

WARNING

Unit

≥

To reduce the risk of fire, electric shock or product damage,

j

Do not expose this unit to rain, moisture, dripping or
splashing.

j Do not place objects filled with liquids, such as vases,

on this unit.

j Use only the recommended accessories.
j Do not remove covers.
j Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

≥

To prevent injury, this apparatus must be securely attached
to the wall in accordance with the installation instructions.

AC power supply cord

≥ The power plug is the disconnecting device.

Install this unit so that the power plug can be unplugged
from the socket outlet immediately.

Button-type battery (Lithium battery)

≥ Risk of fire, explosion and burns. Do not disassemble,

heat above 60

This product contains a coin/button cell battery. If the coin/
button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death. Keep
new and used batteries away from children. If the battery
compartment does not close securely, stop using the
product and keep it away from children. If you think
batteries might have been swallowed or placed inside any
part of the body, seek immediate medical attention.

If any electrolyte should come into contact with your
hands or clothes, wash it off thoroughly with water.
If any electrolyte should come into contact with your
eyes, never rub the eyes. Rinse eyes thoroughly with
water, and then consult a doctor.

<For USA-California only>
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material s special handling
may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

o

C (140oF) or incinerate.

DO NOT INGEST BATTERY,
CHEMICAL BURN HAZARD

.

VQT5J41

2

Precautions

CAUTION

Unit

≥ Do not place sources of naked flames, such as lighted

candles, on this unit.

≥ Product Identification Marking is located on the bottom

of the unit.

Placement

≥ To reduce the risk of fire, electric shock or product

damage,
j Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit
is well ventilated.

j Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

Button-type battery (Lithium battery)

≥

Danger of explosion if battery is incorrectly replaced. Replace
only with the type recommended by the manufacturer.

≥ Keep out of reach of children.
≥ Insert with poles aligned.
≥ Mishandling of batteries can cause electrolyte leakage

and may cause a fire.

j

Remove the battery if you do not intend to use the remote
control for a long period of time. Store in a cool, dark place.

j Do not heat or expose to flame.
j Do not leave the battery(ies) in a car exposed to

direct sunlight for a long period of time with doors and
windows closed.

j

Do not touch the terminals (i and j) with metal objects.

j Do not recharge, disassemble, remodel, heat or

throw into fire.

≥ When disposing of the batteries, please contact your

local authorities or dealer and ask for the correct
method of disposal.

The following mark and symbols are located
on bottom of the unit.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.

FCC Note:

This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following measures:

≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and

receiver.

≥ Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

≥ Consult the dealer or an experienced radio/TV

technician for help.

Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate this
device.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.

Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102-5490

Support Contact: http://www.panasonic.com/contactinfo

‘

This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines. This
equipment has very low levels of RF energy that is
deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be
installed and operated keeping the radiator at least

7

/8q) or more away from person’s body (excluding

20 cm (7
extremities: hands, wrists, feet and ankles).

‘

FCC ID:ACJ-SC-HTB8

VQT5J41

3

Table of contents

IMPORTANT SAFETY INSTRUCTIONS ............................................................ 2

Before use

Supplied items ................................................................................................... 5

This system ................................................................................................................................ 5

Accessory................................................................................................................................... 5

Control reference guide .................................................................................... 6

This system (Front)..................................................................................................................... 6

This system (Rear)..................................................................................................................... 6

Remote control ........................................................................................................................... 7

Getting started

Step 1 Connections ........................................................................................... 8

Connection with the TV .............................................................................................................. 8

Connection with other devices.................................................................................................... 8

AC power supply cord connection .............................................................................................. 8

Bluetooth

Step 2 Placement ............................................................................................. 10

Safety Precautions ................................................................................................................... 10

Wireless interference................................................................................................................ 10

Selecting the placement method .............................................................................................. 11

When placing the main unit on a rack or on a table ................................................................. 12

When attaching the main unit to a wall..................................................................................... 13

®

connection ................................................................................................................ 9

Operations

Using this system ............................................................................................ 15

Advanced operations ...................................................................................... 16

Reference

Troubleshooting .............................................................................................. 17

About Bluetooth

Unit care ........................................................................................................... 19

License ............................................................................................................. 19

Indicator illumination ...................................................................................... 20

Specifications .................................................................................................. 21

Limited Warranty

(ONLY FOR U.S.A.) ...................................................................................... 22

VQT5J41

4

®

............................................................................................. 19

Precautions

Reference Getting started

Before useOperations

Before use

≥ The illustrations shown may differ from your unit.
≥ Operations in this Owner’s Manual are described mainly with the remote control, but you can

perform the operations on the main unit if the controls are the same.

Supplied items

This system

∏ 1 Main unit (Speaker)

(SC-HTB8)

Accessory

Check the supplied accessory before using this system.

∏ 1 Remote control

(with a battery)

(N2QAYC000102)



≥ Product numbers are correct as of March 2014. These may be subject to change.
≥ To order accessories, refer to “Accessory Purchases (United States)” on page 22.

VQT5J41

5

Control reference guide

ヷヰロ

リワヱヶヵ

⾼

ヱモリンリワヨ

ヵヷ

ャュバュヷュ

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

1 2 34

56

7

10
11
12

89

This system (Front)

1 Standby/on switch (Í/I)

Press to switch the unit from on to standby mode or
vice versa. In standby mode, the unit is still
consuming a small amount of power.

2 Adjust the volume of this system (> p. 15)
3 Select the input source (> p. 15)

“TV” --# “BD/DVD” --# “” (

^--------------------------------------------------------}

4 Select the Bluetooth

®

device as the source

Bluetooth

®

)

(> p. 15)

This system (Rear)

8 AC power supply cord (> p. 8)
9 Wall mounting hole
10 OPTICAL DIGITAL AUDIO IN terminal (>p. 8)

5 Input selector indicators

§1

A TV indicator

Lights green when the TV is the audio source

B BD/DVD indicator

Lights amber when the device connected to the
BD/DVD terminal is the audio source

C Bluetooth® indicator

Lights amber when the Bluetooth® device is the
audio source

6 Sound mode indicators

§1

D CLEAR VOICE indicator

Lights amber when clear voice is the current
sound mode

E SURROUND indicator

Lights amber when surround is the current
sound mode

7 Remote control signal sensor (> p. 7)

11 AUDIO IN terminal (> p. 8)
12 MULTI ANGLE switch (> p. 12, 13)

Switch the audio quality according to the placement
method of the main unit.

§1 The indicators will also blink in various conditions. (> p. 20)

§2 For service use only

VQT5J41

6

Before use

Remote control

∫ Before using for the first time

Remove the insulation sheet A.

1

INPUT

2

3

SURROUND

CLEAR VOICE

4

5

6

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

7

1 Turn the main unit on or off (> p. 15)
2 Turn the surround effect on or off (> p. 15)





3 Turn the clear voice effect on or off (> p. 15)
4 Select the input source (> p. 15)

“TV” --# “BD/DVD” --# “” (

Bluetooth

®

)

^--------------------------------------------------------}

5 Adjust the volume of this system (> p. 15)
6 Select the Bluetooth

®

device as the source

(> p. 15)

≥ Set the button-type battery with its (i) mark

facing upward.

7 Mute the sound (> p. 15)

∫ About remote control signal sensor

The remote control signal sensor is located on the main unit.

≥Use the remote control within the correct operation range.

Distance: Within approx. 7 m (23 ft) directly in front
Angle: Approx. 30

o

left and right

B Remote control signal sensor



VQT5J41

7

Getting started

TV

L

R

AUDIO OUT

B

BD/DVD

AUDIO IN

WHITE:

RED:

L

R

e.g., Blu-ray Disc player

D

C

Step 1 Connections

≥Turn off all equipment before connection and read the appropriate operating instructions.

Do not connect the AC power supply cord until all other connections are completed.

Connection with the TV

A

OPTICAL

A Optical digital audio cable

≥ When you use the optical digital audio cable, insert the tip correctly into the terminal.
≥ Do not bend the optical digital audio cable.
≥ The optical input supports PCM only.

OUT

Connection with other devices

B Audio cable

AC power supply cord connection

≥ Connect only after all other connections are completed.

C To an AC outlet
D AC power supply cord

≥This system consumes a small amount of AC power

(> p. 21) even when it is turned off. In the interest
of power conservation, if you will not be using this
system for a long time, unplug it from the AC outlet.

OPTICAL

TV

DIGITAL

AUDIO IN

VQT5J41

8

Getting started

Bluetooth® connection

By using the Bluetooth® connection, you can listen to the sound from your Bluetooth® audio device to this
system wirelessly.

≥

Refer to the operating instructions of the Bluetooth® device for further instruction on how to connect a Bluetooth® device.

Preparation

≥Turn on the Bluetooth® feature of your device and place your device near the main unit.

Bluetooth® pairing

Press [ ] to select “ ”.

≥ If the “ ” indicator flashes quickly, go to step 3.

Press and hold [ ] until the “ ” indicator flashes quickly.

≥ If the “ ” indicator flashes slowly, repeat step 2.

Select “SC-HTB8” from the Bluetooth® menu of your device.

≥ If prompted for the passkey on the Bluetooth® device, enter “0000”.
≥ Once the Bluetooth

®

device is connected, the “ ” indicator stops flashing and lights up.



≥ You can register 8 or more Bluetooth® devices to this unit.

However, when this unit is turned off, it can store only up to 8 registered devices. If you register 9 or more devices,
devices with the oldest connection history will be deleted.

Connecting a paired Bluetooth® device

Press [ ] to select “ ”.

≥ If the “ ” indicator lights, a Bluetooth® device is already connected with this system. Disconnect it. (> below)

Select “SC-HTB8” from the Bluetooth® menu of your device.

∫ Disconnecting a Bluetooth® device

Press and hold [ ] until the “ ” indicator flashes slowly.



≥

When “ ” is selected as the source, this system will automatically try and connect to the last connected Bluetooth® device.
If the connection attempt fails, try to establish a connection again.

≥ The Bluetooth® device will be disconnected if a different audio source (e.g. “TV”) is selected.
≥ This system can only be connected to one device at a time.

VQT5J41

9

Step 2 Placement

Safety Precautions

Professional installation is required.
The installation should never be done by any other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING
DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.

≥ Be sure to install the main unit as indicated within this Owner’s Manual.
≥ Attach using techniques suited to the structure and materials of the installation location.

Caution

≥ This system is to be used only as indicated in these instructions. Failure to do so may

lead to damage to the amplifier and/or the speaker, and may result in the risk of fire.
Consult a qualified service person if damage has occurred or if you experience a
sudden change in performance.

≥ Do not attempt to attach the main unit to a wall using methods other than those

described in this manual.



≥ Do not hold the main unit in one hand to avoid injury, you may drop the main unit when carrying it.
≥ To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.

Wireless interference

To avoid interference, maintain the following distances between the main unit and other
electronic devices that use the same radio frequency (2.4 GHz band).

10

A

VQT5J41

A Main unit
B Wireless router, cordless phone and

other electronic devices: approx. 2 m

1

/2 ft)

(6

B

Getting started

Precautions

Selecting the placement method

When placing the main unit
on a rack or on a table

≥ Place the main unit on a flat

and horizontal surface.

≥ Place the main unit in front of

the TV pedestal.

When attaching the main
unit to a wall

≥ Place the main unit on a

flat and vertical surface.

Page 12

Page 13

Choose a placement method that suits you best.

∫ When placing the main unit in front of the TV

The main unit may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic
Tracking System) sensor, remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D
compatible TV.
≥If interference occurs, move the main unit further away from the TV. If the TV still does not function

correctly, try using it in a rack or in the wall mount position.

∫ If the TV’s remote control sensor is blocked by the main unit

Try using the TV’s remote control from a different angle.



≥ Do not use the main unit in a metal cabinet.
≥ If irregular coloring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the main unit further

away from the TV.

≥ Keep magnetized items away. Magnetized cards, watches, etc., can be damaged if placed too close to the main unit.
≥ Keep the main unit approximately 150 mm (6q) away from the TV.

VQT5J41

11

When placing the main unit on a rack or on a table



Additionally required accessories (commercially available)

≥Fall prevention cord ..................................................................................................................... k 1

≥Screw eye (to attach the fall prevention cord)............................................................................... k 1



≥ Use commercially available screws that are capable of supporting over 33 kg (73 lbs).
≥ Use a cord that is capable of supporting over 10 kg (22 lbs) (with a diameter of about 2 mm (

Slide the MULTI ANGLE switch to “RACK/TABLE TOP”.

≥Press the AC power supply cord into the holder.

Attach the cord to the main unit.

3

/32q)).

A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

§

about 5 mm (

3

/16q) apart from the tip, at an angle of 45o (as illustrated above).

Place the main unit in the desired position and attach the cord onto the rack or table.

≥ Make sure that the slack of the cord is minimal.
≥ Do not lean the main unit against the TV or wall.
≥ Do not place the main unit over the AC power supply cord.
≥ Ensure that the main unit is stable.

B Screw eye

≥Attach at a position capable of supporting over 10 kg (22 lbs).
≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.

VQT5J41

12



Getting started

Precautions

When attaching the main unit to a wall

Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg (73 lbs).
The screws and other items are not supplied as the type and size will vary with each installation.

≥Refer to step 3 for details about the required screws.
≥Be sure to attach the fall prevention cord as a secondary safety measure.

Additionally required accessories (commercially available)

≥Screws for wall mounting ............................................................................................................. k 2

≥Fall prevention cord...................................................................................................................... k 1

≥Screw eye (to attach the fall prevention cord) .............................................................................. k 1



≥ Use a cord that is capable of supporting over 10 kg (22 lbs) (with a diameter of about 2 mm (3/32q)).

Slide the MULTI ANGLE switch to “WALL MOUNT”.

Attach the cord to the main unit.



A Cord

§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations,

§

about 5 mm (

3

/16q) apart from the tip, at an angle of 45o (as illustrated above).

VQT5J41

13

Drive a screw into the wall.











≥ Use the measurements indicated below to identify the screwing positions on the wall.
≥ Leave at least 20 mm (
≥ Leave at least 10 mm (

mount the main unit successfully.

≥ Be sure to use a level to insure that both mounting holes are level to each other.

Front view (semi-transparent image)





25

/32q) of space above of the main unit to allow enough space for fitting the main unit.

13

/32q) of space on both sides of the main unit. Without sufficient space, it is not possible to





B At least 30 mm (1
C ‰4.0 mm (

5

/32q)

D ‰7.5 mm to ‰9.4 mm (
E Wall or pillar
F 7.5 mm to 8.5 mm (

3

/16q)

9

/32q to 3/8q)

7

/32q to 11/32q)

G 320 mm (12
J 15 mm (

19

/32q) H 215 mm (8

19

/32q) K 115 mm (417/32q) L Wall mounting hole

Fit the main unit securely onto the screw(s).

DO DO NOT

≥ Move the speaker so

that the screw is in this
position.

Secure the cord to the wall.

≥ Make sure that the slack of the cord is minimal.





15

/32q) I 215 mm (815/32q)

≥

In this position, the
speaker will likely fall if
moved to the left or right.

M Screw eye
N Cord

14

VQT5J41

Getting started

Operations

Precautions

Operations

CLEAR VOICE

SURROUND

PAIRING

----

INPUT

Using this system

Preparation

≥ Turn on the TV and/or connected device.

Press [Í] to turn on the main unit.

Select the source.

Press To select

[INPUT]

[] “ ” (Bluetooth

≥ This remote control cannot be used to control the operations

of the connected devices.

∫ When “ ” is selected as the source

On the Bluetooth® device:
Select this system as the output source of the
connected Bluetooth
playback.

∫ When “BD/DVD” is selected as the

source

On the TV and the connected device:
Select the TV’s input for this system and start the
playback on the connected device.

“TV” --------------# “BD/DVD”

^--- “ ” (Bluetooth

®

)

®

device and start the

®

) !-}

∫ To adjust the volume of this system

Press [i VOL j].

≥ Volume range: 0 to 100

§

∫ To set the surround mode

You can enable/disable the surround effect.

Press [SURROUND].

≥ To cancel, press the button again.

∫ To set the clear voice mode

With the clear voice mode you can hear dialogs clearer.

Press [CLEAR VOICE].

≥ To cancel, press the button again.

∫ To mut e the s o und

Press [MUTE].

≥ While muting, all the indicators blink simultaneously.
≥ To cancel, press the button again or adjust the volume.
≥ Muting is canceled if the main unit is turned off.



If this system does not operate as expected or sound is unusual, returning the settings to the
factory preset may solve the problem. (> p. 17)

§

BD/DVD indicator, Bluetooth® indicator and sound mode indicators blink from left to right (i) or from right to left (s) while adjusting.
The indicators will not blink when it has reached the maximum or minimum.

≥ If there is sound coming out of the TV’s speakers, reduce the volume of the TV to its minimum.
≥ If the main unit is turned off with the volume setting in the greater half (above 50), the main unit will automatically

lower the volume to the middle (50) when the main unit is turned on (Volume limitation).
To turn this function off, refer to page 16.

VQT5J41

15

Advanced operations

ヤロユモンチヷヰリヤユ

Auto Power Down

The main unit is automatically turned off if there is no audio
input and when you do not use it for approx. 2 hours.

While pressing and holding
[CLEAR VOICE] on the remote
control, press and hold [INPUT] on
the main unit for more than 4 sec to
display the current setting.

“BD/DVD” indicator blinks:

ャュバュヷュ

Auto Power Down is on.

“CLEAR VOICE” indicator blinks:

Auto Power Down is off.

While the setting is displayed, press
[CLEAR VOICE] to select the setting.

≥ The setting changes each time [CLEAR VOICE] is pressed.
≥ The indicator for the selected setting blinks for 20 sec and

then exits the setting mode.

≥ The setting is maintained until it is changed again.
≥ Default setting of this function is off.

Bluetooth® Stand-by

This function allows you to connect a paired Bluetooth®
device when the main unit is in standby mode.

While pressing and holding
[SURROUND] on the remote control,
press and hold [ ] on the main unit
for more than 4 sec to display the
current mode.

“BD/DVD” indicator blinks:

ャュバュヷュ

Bluetooth

“CLEAR VOICE” indicator blinks:

ヤロユモンチヷヰリヤユ

Bluetooth

®

Stand-by is on.

®

Stand-by is off.

Dimmer mode

You can turn off dimmer mode and keep the LED
indicators bright.

While pressing and holding [INPUT] on
the remote control, press and hold
[s VOL] on the main unit for more than
4 sec to turn off Dimmer mode.

≥ The indicator for the current condition will turn brighter.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is on.



To turn on dimmer mode, repeat the operation above.
After performing the operation, the indicator for the current
condition will be dim.

Others

∫ Remote control code

When other Panasonic devices respond to this system’s
remote control, change the remote control code on this
system and the remote control.

Preparation

≥ Turn off all other Panasonic products.
≥ Turn on the main unit.

Change the remote control code to code 2:

1 Aim the remote control at the main unit’s

remote control sensor.

2 Press and hold [MUTE] and [ ] on the remote

control for more than 4 sec.

≥ All the indicators will blink for 10 sec when the code of

this system is changed.

ヵヷ

ャュバュヷュ

≥ The setting is maintained until it is changed again.

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ



≥ If the main unit does not operate after changing the code,

repeat steps 1 and 2.

≥ To change the remote control code to code 1, repeat the

steps above, but replace

[] with [INPUT].

While the mode is displayed, press
[SURROUND] to select the mode.

≥ The setting changes each time [SURROUND] is pressed.
≥ The indicator for the selected setting blinks for 20 sec and

then exits the setting mode.

≥ The setting is maintained until it is changed again.
≥ Default setting of this function is off.

VQT5J41

16

∫ To turn off the volume limitation

If a state of the lowered volume disturbs you every time
the main unit turns on, for example, it is possible to turn off
this function as follows:

While pressing and holding [MUTE] on the remote control,
press and hold [VOL

≥ All the indicators will blink once when the volume limitation

is turned off.

i

] on the main unit for more than 4 sec.

ヵヷ

ャュバュヷュ

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ



To reset the setting, return to the factory preset. (> p. 17)

Reference

Operations

Reference

Troubleshooting

Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated in the following guide do not solve the
problem, refer to “Customer Services Directory (United
States)” on page 22.

To return to the factory defaults.

While the main unit is on, press and hold [Í/I] on
the main unit for more than 4 sec.
(All the indicators will blink twice when this
system is reset.)

If this system does not operate as expected,
returning the settings to the factory defaults
may solve the problem.

The remote control code will return to “1” when

≥

this system is returned to the factory preset. To
change the remote control code, refer to page 16.

General operation

No power.

≥ Insert the AC power supply cord securely. (> p. 8)
≥ If the indicators blink and the main unit turns off

immediately after you have turned it on, unplug the AC
power supply cord and consult your dealer.

The remote control does not work properly.

≥ The battery is depleted. Replace it with a new one.

(> p. 7)

≥ It is possible that the insulation sheet has not been

removed. Remove the insulation sheet. (> p. 7)

≥ It may be necessary to set the code of the remote

control again after changing the battery of the remote
control. (> p. 16)

≥ Use the remote control within the correct operation

range. (> p. 7)

Bluetooth

®

Pairing cannot be done.

Check the Bluetooth® device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or the

registration has been replaced. Try pairing the device
again. (> p. 9)

≥ This system might be connected to a different device.

Disconnect the other device and try pairing the device
again.

The device is connected but audio cannot be
heard through this system.

For some built-in Bluetooth® devices, you have to set the
audio output to “SC-HTB8” manually. Read the operating
instructions for the device for details.

The sound is interrupted.

≥

The device is out of the 10 m (33 ft) communication range.
Bring the Bluetooth

≥ Remove any obstacle between the main unit and the

device.

≥ Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.) are
interfering. Bring the Bluetooth
main unit and distance it from the other devices.

®

device closer to the main unit.

®

device closer to the

The “TV” indicator blinks.

Unplug the AC power supply cord and consult your dealer.
If other indicators are also blinking, be sure to inform your
dealer of these indicators.

The main unit is automatically switched to
standby mode.

“Auto Power Down” function is on.
The main unit will automatically switch to standby mode
when no signal is input and no operation is performed for
approx. 2 hours. Refer to page 16 to turn this function off.

VQT5J41

17

Sound

No sound.

≥ Turn muting off. (> p. 15)
≥ Check the connections to the other device. (> p. 8)
≥ Make sure that the received audio signal is compatible

with this system. (> p. 21)

≥ Turn this system off and then on again.
≥ If the connections are correct, there might be a problem

with the cables. Redo the connections with different
cables.

≥

Check the audio output settings on the connected device.

The volume is lowered when the main unit is
turned on.

If the main unit is turned off with the volume setting in the
greater half (above 50), the main unit will automatically
lower the volume to the middle (50) when the main unit is
turned on. (> p. 16)

The dialog is too persistent or the dialog does
not sound natural.

This system has a function to make the dialog stand out
when the volume is low. (> p. 15)

There is no audio.
The power of the main unit turns off
automatically.

(When the main unit detects a problem, a safety measure
is activated and the main unit automatically switches to
standby mode.)

≥ There is a problem with the amplifier.
≥ Is the volume extremely high?

If so, lower the volume.

≥ Is this system placed in an extremely hot place?

If so, move this system to a cooler place and wait a few

moments and then try to turn it on again.
If the problem persists, check if the TV indicator and the
BD/DVD indicator are blinking first. After checking the
indicators, turn off this system, unplug the AC power
supply cord, and consult your dealer. Make sure to
remember which indicators were blinking and inform the
dealer of them.

18

VQT5J41

Reference

About Bluetooth

®

Panasonic bears no responsibility for data
and/or information that is compromised
during a wireless transmission.

∫ Frequency band used

This system uses the 2.4 GHz frequency band.

∫ Certification of this device

≥ This system conforms to frequency restrictions and has

received certification based on frequency laws. Thus, a
wireless permit is not necessary.

≥ The action below are punishable by law in some

countries:

j Taking apart or modifying the unit.
j Removing specification indications.

∫ Restrictions of use

≥ Wireless transmission and/or usage with all Bluetooth®

equipped devices is not guaranteed.

≥ All devices must conform to standards set by Bluetooth

SIG, Inc.

≥ Depending on the specifications and settings of a

device, it can fail to connect or some operations can be
different.

≥ This system supports Bluetooth

depending on the operating environment and/or
settings, this security is possibly not sufficient. Transmit
data wirelessly to this system with caution.

≥ This system cannot transmit data to a Bluetooth

device.

®

security features. But

®

∫ Range of use

Use this device at a maximum range of 10 m (33 ft).
The range can decrease depending on the environment,
obstacles or interference.

∫ Interference from other devices

≥ This system may not function properly and troubles

such as noise and sound jumps may arise due to radio
wave interference if the main unit is located too close to
other Bluetooth

2.4 GHz band.

≥ This system may not function properly if radio waves

from a nearby broadcasting station, etc. are too strong.

®

devices or the devices that use the

∫ Intended usage

≥ This system is for normal, general use only.
≥ Do not use this system near equipment or in an

environment that is sensitive to radio frequency
interference (example: airports, hospitals, laboratories,
etc).

Unit care

∫ Clean this system with a soft, dry cloth

≥ When dirt is heavy, wring a cloth moistened in water

tightly to wipe the dirt, and then wipe it with a dry cloth.

≥ Never use alcohol, paint thinner or benzine to clean this

system.

≥ Before using chemically-treated cloth, carefully read the

instructions that came with the cloth.

∫ To dispose or transfer this system

This system may keep the user settings information in the
main unit. If you discard the main unit either by disposal or
transfer, then follow the procedure to return all the settings
to the factory presets to delete the user settings.
(> p. 17, “To return to the factory defaults.”)

≥ The operation history may be recorded in the memory

of the main unit.

License

The Bluetooth® word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by
Panasonic Corporation is under license. Other trademarks
and trade names are those of their respective owners.

VQT5J41

19

Indicator illumination

ヵヷ

ャュバュヷュ

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

The indicators display the condition of this system by flashing. The indicator patterns illustrated below
are displayed during normal operational conditions. They do not refer to the indications of a problem.

Indicator Description

ヵヷ

ャュバュヷュ

ヵヷ

ャュバュヷュ

ヵヷ

ャュバュヷュ

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

ヤロユモンチヷヰリヤユ ヴヶンンヰヶワュ

The indicator blinks for 20 sec.

≥ When the setting is on

( “Auto Power Down” and “Bluetooth

®

Stand-by”) (> p. 16)

The indicator blinks for 20 sec.

≥ When the setting is off

( “Auto Power Down” and “Bluetooth

The indicators blink for 10 sec.

≥ When the remote control code is changed (> p. 16)

®

Stand-by”) (> p. 16)

The indicators blink once.

≥ When changing the setting

( “To turn off the volume limitation”) (> p. 16)

The indicators blink twice.

≥ When the main unit is reset (> p. 17)

Bluetooth

≥ When the main unit is ready for pairing (> p. 9)

Bluetooth

≥ When the main unit is waiting to connect (> p. 9)

Bluetooth

≥ When the main unit is connected with a Bluetooth

®

indicator blinks quickly.

®

indicator blinks slowly.

®

indicator turns on.

(> p. 9)

®

device

VQT5J41

20

Reference

Specifications

AMPLIFIER SECTION

RMS output power : Stereo mode

Front ch (non-simultaneous drive)

40 W per channel (1 kHz, 10 % THD, 8 ≠)

Total RMS Stereo mode power

80 W

FTC output power Stereo mode

Front ch (both ch driven)

200 Hz-20 kHz 25 W per channel (1 % THD, 8 ≠)

Total FTC Stereo mode power

50 W

SPEAKER SECTION

FRONT SPEAKER (L/R)

Typ e

1 way, 1 speaker system (passive radiator type)

Unit(s)

8cm k2 (3

1

/8q) (Cone type)

Impedance

Passive Radiator

Unit(s)

8cm k2 (3

Bluetooth® SECTION

Bluetooth® system specification

Bluetooth

Wireless equipment classification

Supported profiles

Supported codec

Frequency band

Operating distance

approx. 10 m (33 ft) Line of sight

®

Version 3.0

Class 2 (2.5 mW)

A2DP (with SCMS-T)

SBC

2.4 GHz band FH-SS

TERMINALS SECTION

Digital Audio Input (TV)

Optical digital input

Optical terminal

Sampling Frequency

32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

Audio Format

Analog Audio Input (BD/DVD)

Audio input

GENERAL

Power consumption

Power consumption in standby mode

Approx. 0.5 W

Power supply AC 120 V, 60 Hz

8 ≠

For table top layout
Dimensions (WkHkD)

1

/8q)

750 k65.5 k118 m m

17

/32qk219/32qk421/32q)

(29

For wall mounting layout
Dimensions (WkHkD)

750 k115 k65 mm

17

/32qk417/32qk29/16q)

(29

Mass (Weight)

Approx. 2.3 kg (5.07 lbs)

Operating temperature range

o

C to r40oC (r32oF to r104oF)

0

Operating humidity range

20 % to 80 % RH (no condensation)



≥ Specifications are subject to change without notice.
≥ Mass and dimensions are approximate.
≥ Total harmonic distortion is measured by a digital spectrum

analyzer.

LPCM

Pin jack

16 W

VQT5J41

21

Limited Warranty (ONLY FOR U.S.A.)

Panasonic Products Limited Warranty

Limited Warranty Coverage
(For USA Only)

If your product does not work properly because of a defect in materials or
workmanship, Panasonic Corporation of North America (referred to as “the
warrantor”) will, for the length of the period indicated on the chart below,
which starts w ith the da te of origin al purchase ( “warranty period”), a t its
option either (a) repair your product with new or refurbished parts, (b)
replace it with a new or a refurbished equivalent value product, or (c) refund
your purchase price. The decision to repair, replace or refund will be made
by the warrantor.

Product or Part Name Parts Labor

Home Theater Audio System 1 Year 1 Year

All included Accessories
(Except Non-Re chargeable Batteries)

Only Non-Rechargeable Batteries 10 Days

During the “Labor” warranty period there will be no charge for labor. During
the “Parts” warranty period, there will be no charge for parts. This Limited
Warranty excludes both parts and labor for non-rechargeable batteries,
antennas, and cosmetic parts (cabinet). This warranty only applies to
products purchased and serviced in the United States. This warranty is
extended only to the original purchaser of a new product which was not sold
“as is”.

90 Days

Mail-In Service--Online Repair Request

Online Repair Request

To submit a new repair request and for quick r epair status v isit our Web S ite
at www.panasonic. com/repair

When shipping the unit, carefully pack, include all supplied accessories listed
in the Owner ’s Manual, and send it pr epaid, adequat ely insured and pac ked
well in a carton box . When shipping Lith ium Ion batteries pleas e visit our
Web Site at www.panasonic.com/BatteryHandling
committed to providing the most up to date information. Include a letter
detailing the complaint, a return address and provide a daytime phone
number where you can be reached. A valid registered receipt is required
under the Limited Wa rranty.

IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/
PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT
PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED
FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF
OF PURCHASE.

Limited Warranty Limits And Exclusions

This warranty ONLY COVERS failures due to defects in materials or
workmanship, and DOES NOT COVER normal wear and tear or cosmetic
damage. The warranty ALSO DOES NOT COVER damages which occurred
in shipment, or failures which are caused by products not supplied by the
warrantor, or fail ures which resul t from accidents , misuse, abus e, neglect,
mishandling, misapplication, alteration, faulty installation,
set-up adjustments, misadjustment of consumer controls, improper

The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for future
reference.

MODEL NUMBER

SERIAL NUMBER

.

as Panasonic is

SC-HTB8

Not
Applicable

Not
Applicable

maintenance, power line surge, lightning damage, modification, introduction
of sand, humidity or liquids, commercial use such as hotel, office, restaurant,
or other bus iness or re ntal use of th e product, o r service by anyone oth er
than a Factor y Service C enter or othe r Authorized Servicer, or dama ge that
is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED
UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS
WARRANTY.

(As examples, this excludes damage s for lost time, travel to and from the
servicer, loss of or damage to media or images, data or other memory or
recorded content. The items listed are not exclusive, but for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD
OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts,
so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from s tate to state. If a problem with this pr oduct devel ops
during or after the warranty period, you may contact your dealer or Service
Center. If the problem is not handled to your satisfaction, then write to the
warrantor ’s Consumer A ffairs Departm ent at the addresses li sted for the
warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.

Customer Services Directory (United States)

Obtain Product Information and Operating Assistance; locate
your nearest Dea ler or Service Cente r; purchase Par ts and
Accessories; or make Customer Se rvice and Literatu re requests
by visiting our Web Site at:
http://www.panasonic.com/
or, contact us via the web at:
http://www.panasonic.com/contactinfo

For hearing or sp eech impaired TTY us ers, TTY: 1-877-833-8855

support

Accessory Purchases (United States)

Purchase Parts, Accessories and Owner’s Manual online for all
Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
Or, send your request by E-mail to:
[e-mail]
You may also contact us directly at:
1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic National Parts Center
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express)

For hearing or sp eech impaired TTY us ers, TTY: 1-866-605-1277

As of April 2014

User memo:

DATE OF PURCHASE ______________________________
DEALER NAME ___________________________________
DEALER ADDRESS________________________________
_________________________________________________
TELEPHONE NUMBER _____________________________

22

VQT5J41

Reference

VQT5J41

23

Panasonic Corporation 2014

Printed in China

Two Riverfront Plaza, Newark, NJ 07102-5490

http://www.panasonic.com

Panasonic Corporation of North America

-If you see this symbol-

Information on Disposal in other Countries outside the
European Union

This symbol is only valid in the European Union.
If you wish to discard this product, please contact
your local authorities or dealer and ask for the
correct method of disposal.

VQT5J41

F0314KE0