Panasonic KX-TGA520, KX-TGA520M User Manual

5.8 GHz Expandable Cordless Handset
)
Model No.
KX-TGA520
Installation Manual
PLEASE READ BEFORE USE AND SAVE.
This handset is an accessory cordless handset, for use with Panasonic base units KX-TG5200/KX-TG5202/KX-TG5210/KX-TG5212/KX-TG5213/KX-TG5230/KX-TG5240/ KX-FPG391. This installation manual only describes the steps necessary to start up the handset. Please read the base unit operating instructions for further details.
Accessories (included) For extra orders, call 1-800-332-5368.
A Charger Unit . . . . . . . . . . . . . . . . . . . . . . .one
Charger Order No. PQLV30024ZM AC Adaptor Order No. KX-TCA1-G (KX-TCA1)
A Handset Cover. . . . . . . . . . . . . . . . . . . . . .one
Order No. PQKK10142Z1
Installation
Connect the Charger unit
AC Adaptor
A Battery . . . . . . . . . . . . . . . . .one
Order No. HHR-P104
A Belt Clip . . . . . . . . . . . . . . . .one
Order No. PQKE10377Z1
Power Outlet (AC 120 V, 60 Hz
USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G).
The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel
warm during use.)
Install the battery
Insert the battery (1), and press it down until it snaps into the compartment (2). Close the cover.
1
For assistance, please call: 1-800-211-PANA(7262)
– 1 –
2
PQQX14000ZA S0104-0
Charging the battery
Place the handset on the charger and charge for 6 hours before initial use.
The unit beeps once, the CHARGE indicator
lights and “Charging” is displayed.
When the battery is fully charged, “Charge
completed” is displayed if there are no new
calls in the Caller List.
Recharge the battery when:
—“Recharge battery” is displayed on the
handset,
3” flashes, or
—“ — the handset beeps intermittently while it is in
use.
If the battery has been discharged, the handset will display “Charge for 6 HRS” and
4” when you place the handset on the charger. The handset will not work unless the
“ battery is charged. Continue charging.
Charge Contacts
CHARGE Indicator
Handset battery information
After your Panasonic battery is fully charged, you can expect the following performance:
Operation Operating time
While in use (TALK) Up to 5 hours While not in use (Standby) Up to 11 days While using the Clarity Booster feature Up to 3 hours
• Clean the charge contacts of the handset and the charger with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the battery may not charge properly.
Belt Clip
You can hang the handset on your belt or pocket using the included belt clip.
To attach the belt clip To remove the belt clip
While pressing the top of the clip (1), pull the right edge in the direction of the arrow (
– 2 –
2).
B
A
Registration
OK
BACK
L
This cordless handset must be registered to a KX-TG5200/KX-TG5202/KX-TG5210/ KX-TG5212/KX-TG5213/KX-TG5230/KX-TG5240/KX-FPG391 base unit. The handset will be assigned the extension number at registration. Only one handset can be registered at a time. Charge the battery fully. Make sure the base unit and the other handsets are not
being used.
Have both the handset and base unit nearby during registration.
*LOCATOR Button
Press LOCATOR on base unit for 3 sec. Then press OK
BACK
To operate “
[-]
1
OK
”,
OK
press the right soft key.
CHARGE Indicator
Base unit model shown here is KX-TG5240.
*
The location of the KX-TG5200/KX-TG5202: KX-TG5210/KX-TG5212/KX-TG5213: KX-TG5230/KX-TG5240
The handset display shows the instructions as shown on the right.
LOCATOR
button varies by base unit model.
LOCATOR
[], [], [], []
LOCATOR/INTERCOM
or
[]
[], [], [], []
/KX-FPG391: [LOCATOR/INTERCOM/TRANSFER]
or
Press LOCATOR on base unit for 3 sec. Then press OK
BACK
PLAY OK
1 Base unit: Press and hold the *LOCATOR button for 3 seconds.
The CHARGE indicator flashes. After the CHARGE indicator starts flashing, the rest of
the procedure must be completed within 1 minute.
On the KX-FPG391, “HS REGISTRATION” is displayed.
2 Handset:
(1) Press the soft key ( ).
OK
IN USE
SPI
PRIVACY
Handset
1
[]
L
-
]
Registering
(2) Wait until a long beep sounds and the display
shows the new extension number.
Registration is complete.
Ex. Extension number 2
IN USE
SPI
PRIVACY
Handset [2] Registered
The registered number “[1]” to “[4]” is shown on the top right of the display.
You can stop registration by pressing [OFF] on the handset and pressing the *LOCATOR
button on the base unit.
If you try to register this handset to the KX-TG6500 base unit, “Wrong handset Refer
to manual” is displayed. The base units for this handset are mentioned above.
To cancel the handset registration, please see your base unit Operating Instructions.
For assistance, please call: 1-800-211-PANA(7262)
– 3 –
1
2
]
Selecting the display language
You can select either “English” or “Spanish” as the display language. The factory preset is “English”. Press [MENU] N [d] or [B] to select “Initial settingN Soft key ( ) N
N [d] or [B] to select “Change language” N to select “Español”, or soft key ( ) to select “English” N Soft key ( ) for Spanish, or soft key ( ) for English
SAVE
ENGLISH
N
Soft key ( ) N Soft key ( )
[OFF]
SELECT
SELECT
GUARDAR
Optional Headset
Connecting an optional headset to the handset allows hands-free phone conversation. Please use only a Panasonic KX-TCA60, KX-TCA86, KX-TCA88, KX-TCA88HA, KX-TCA91, KX-TCA92 or KX-TCA98 headset. To order, call the accessories telephone number on page 1.
Connecting an optional headset
Open the headset jack cover, and insert the headset plug into the headset jack as shown below.
Headset Jack
Headset sold separately. Model shown here is KX-TCA88.
Wall Mounting
The charger can be wall mounted. Connect the AC adaptor. Install screws using the wall
A
template (see below). Mount the charger ( right (
C
) until it is secured.
2.45 cm
31
⁄32")
(
Screws
To P o we r Outlet
2.45 cm
31
⁄32")
(
Wall Template
). Slide it down (B), then slide down to the
A
B
C
– 4 –
Loading...
+ 8 hidden pages