Panasonic KX-HTS Setup Reference Manual

Draft Version

Setup Reference guide for KX-HTS Series

(Tested with HTS32 Version 1.5)

“VozTelecom” SIP Trunk service

with External Router

Version 0.1(PSCEU) 29th, March 2017

2

 SUMMARY

This document is a reference for configuring “VozTelecom” SIP trunks onto Panasonic HTS and

includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation.

SIP trunk specific account details are provided to you by VozTelecom.

 Attention:

This document was created based on the results of test environment accounts.

Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of

completing this Inter-Operability Test Panasonic will provide technical support for any issues

experienced an assist as far as possible in providing a resolution.

Please obtain relevant information from Service provider before configuration of SIP trunks.

Panasonic will not be held liable for any information provided in this guidance document.

Information used in this document is for interoperability testing.

Information and Specifications in this document are subject to change without notice.

 Note

FAX

FAX T.38 is not supported and G711 Inband FAX communication is failed.

Unable to use FAX to PSTN when FAX message are detected on VozTelecom.

Hold

Hold is not working correctly.

Limitation: HTS won’t allow RE-INVITE (Hold) message from Server. Under study.

CLIR Calls

Limitation: HTS don’t support CLIR Outgoing Calls (Anonymous)

 Table of Contents

(1) SIP Trunk, Extension Port Number and NAT Configuration: Page 4

(2) Network Settings: Page 5

(3) Trunk Port Attribution: Page 7

(4) Provisioning a SIP trunk: Page 8

(5) Incoming Call Routing: Page 12

(6) Outgoing Call CLI: Page 13

(7) CLIR Outgoing Call (Anonymous calls): Not supported: Page 14

(8)Appendix: Router/Firewall Port Forwarding: Page 15

3

 With External Router Example

Internet

To Existing Router

To PC/HUB

LAN1: 192.168.0.101/24

PC

(Enable DHCP)

KX-HDV series

(e.g., KX-HDV230)

Existing User Network

HUB

(192.168.22.1/24)

 Existing User Network: 192.168.22.0 / Subnet Mask: 255.255.255.0 (/24)

 Existing Router IP Address: 192.168.22.1,

 Static DNS: Primary DNS Server 192.168.22.1 / Secondary DNS Server: 8.8.8.8

Existing Router

(192.168.22.0 /24)

WAN1: 192.168.22.99/24

Note

Configure the settings according to the IP address system of the existing user network.

Also, set the IP address which does not duplicate other IP devices.

4

(1) SIP Trunk, Extension Port Number and NAT Configuration

 SIP Extension & SIP Trunk Common

Select [PBX Configuration] - [2. Extension] - [7.SIP Extension Property]

[SIP Extension & SIP Trunk Common]

1. Voice(RTP) UDP port No.(Server): Leave at 12000-

2. SIP Port Number: Leave at 5060

3. NAT Traversal: Leave Off

4. NAT – Fixed Global IP Address: Leave at 0.0.0.0

All other settings can be left at default.

Click [Apply]

Click [Apply Now]

5

(2) Network Settings

 Network Configuration WAN Setting

Select [Network Configuration] - [3.WAN] – [1.WAN Setting] and Select [WAN 1 Channel]

Click [Modify]

HTS WAN-1 IP: 192.168.22.99 (Example)

Assigned HTS WAN IP address by user network administrator

1. WAN Type: Fix IP

2. WAN Connection Name: Leave WAN1_Fix_IP - Reference only-

3. IP address, by your ISP: 192.168.22.99 (Enter your actual IP address)

4. Subnet Mask: 255.255.255.0

5. ISP Gateway Address: 192.168.22.1

6. Static DNS Change to Enable

7. Primary DNS Server: 192.168.22.1

8. Secondary DNS Server: 8.8.8.8

Click [Apply]