Panasonic eygb1n Operation Manual

Operating Instructions

Instructions d’utilisation

Manual de instrucciones

Cordless Screwdriver

Tournevis sans l

Destornillador inalámbrico

Model No: EYFGB1N

EYFGB2N EYFGB3N

IMPORTANT

This manual contains safety information. Read manual completely before rst using this product and save this

manual for future use.

IMPORTANT

Ce manuel contient des informations de sécurité. Veuillez lire l'intégralité du manuel avant la première utilisation de ce produit et conservez ce manuel pour les utilisations futures.

IMPORTANTE

Este manual tiene información de seguridad. Lea todo el manual antes de usar este producto por primera vez y guarde el manual para poderlo consultar en el futuro.

Index/Index/Indice

English: Page 4 Français: Page 14 Español: Página 25

FUNCTIONAL DESCRIPTION DESCRIPTION DES FONCTIONS DESCRIPCIÓN FUNCIONAL

(B)

(A)

(J)

(K)

(L)

(G)

(C)

(H)(I)

(M)

Clutch setting handle and battery are not included. La poignée de réglage de l'embrayage et la batterie ne sont pas incluses. La empuñadura de ajuste de embrague y la batería no están incluidos.

(F)

2 -

(D)

(E)

6.35 mm (1/4") hex quick connect chuck

Mandrin de connexion rapide hexagonal 6,35 mm

(A)

Mandril hexagonal de conexión rápida de 6,35 mm Hole for tool hanger

Trou pour dispositif de suspension de l'outil

(C)

Oricio para el colgador de la herramienta Forward/Reverse lever

Levier d’inversion marche avant/marche arrière

(E)

Palanca de avance/marcha atrás

Control panel Panneau de commande

(G)

Panel de control Battery indication lamp

Témoin indicateur de la batterie

(I)

Lámpara de indicadora de la batería LED light

Lumière DEL

(K)

Luz LED Clutch setting handle

Poignée de réglage de l'embrayage

(M)

Empuñadura de ajuste de embrague

Clutch shutter

Volet d'embrayage

(B)

Cierre del embrague Tightening conrmation lamp

Témoin de conrmation de serrage

(D)

Lámpara de conrmación de apriete Alignment mark

Marques d’alignement

(F)

Marcas de alineación

LED light on/off button Bouton Marche/Arrêt de la lumière DEL

(H)

Botón ENCENDIDO/APAGADO de luz LED

Display

Afchage

(J)

Visor

Variable speed control trigger Gâchette de commande de vitesse

(L)

Disparador del control de velocidad variable

3 -

EN EN

GENERAL SAFETY RULES

WARNING! Read all instructions

Failure to follow all instructions listed

below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below

refers to your mains operated (corded) powe r tool and battery opera ted (cordless) power tool.

SAVE THESE INSTRUCTIONS

Work Area Safety

1) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

Power tools create sparks which may

ignite the dust or fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

1) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets

will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock

if your body is earthed or grounded.

3) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase

the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

A moment of inattention while operating

power tools may result in personal injury.

Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

Avoid accidental starting. Ensure the switch is in the off position before plugging in.

Carrying power tools with your finger on the switch or plugging in the power tools that have the switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

Do not over reach. Keep prope r footing and balance at all times.

This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving parts.

If devices are provided for t he connection of dust extraction and collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust

related hazards.

Power Tool Use and Care

Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it

was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled

with the switch is dangerous and must

be repaired.

Disconnect the plug from the power source and/or the battery pack from

4 -

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool

accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery Tool Use and Care

1) Ensure the switch is in the off position before inserting battery pack.

Inserting battery pack into power tools that have the switch on invites accidents.

Recharge o nly with the charger specified by the manufacturer.

A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs.

Use of any other battery packs may

create a risk of injury and fire.

When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns, or a fire.

Under abusive conditions, liquid may be ejected from battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may

cause irritation or burns.

Service

1) Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of power tool is maintained.

. INTENDED USE

This tool is a Cordless Screwdriver and can be used to tighten bolts, nuts, and screws with

torque control.

III

ADDITIONAL SAFETY RULES

) Wear ear protectors when using the

tool for extended periods.

2) Be aware that this tool is always in an

operating condition, since it does not have to be plugged into an electrical outlet.

3) Hold power tools by insulated gripping

surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the

operator.

4) Do NOT operate the Forward/Reverse

lever when the main switch is on. The battery will discharge rapidly and damage to

the unit may occur.

5) During charging, the charger may become

slightly warm. This is normal.

Do NOT charge the battery for a long period.

6) When storing or carrying the tool, set the

Forward/Reverse lever to the center posi-

tion (switch lock).

7) Do not strain the tool by holding the speed

control trigger halfway (speed control

mode) so that the motor stops.

5 -

EN EN

Symbol Meaning

Volts

Direct current

No load speed

CAUTION:

• If the collar does not return to its origi

nal position or the bit comes out when

pulled on, the bit has not been properly

attached. Make sure the bit is properly attached before use.

9 mm – 13 mm

(23/64" – 33/64")

6.35 mm (1/4")

-1

… min

. ASSEMBLY

Revolutions or

reciprocations per minutes

Electrical capacity of battery

pack

To reduce the risk of

injury, user must read and

understand instruction

manual.

Do not incinerate or heat

battery pack. Do not charge

or use under conditions of

high temperature. Do not ex-

pose to high temperatures.

Do not disassemble or

modify.

Do not expose to rain or

water.

Attaching or Removing Bit

NOTE:

•

When attaching or removing a bit, disconnect battery pack from tool or place the switch in the center position (switch lock).

1. Hold the collar of quick connect chuck and pull it out from the tool.

2. Insert the bit into the chuck. Release the collar.

3. The collar will return to its original position

when it is released. Pull the bit to make sure it does not come out.

5. To remove the bit, pull out the collar in the

same way.

Attaching or Removing Battery Pack

1. To connect the battery pack: Align the highlighted marker points and

attach battery pack.

Slide the battery pack until it locks into

• position.

Alignment

marks

2. To remove the battery pack:

Push down the button and slide the battery pack forward.

Button

6 -

Forward Reverse

Switch lock

OPERATION

[Main Body] Switch and Forward/Reverse

Lever Operation

CAUTION:

To prevent damage, do not operate Forward/Reverse lever until the bit comes

to a complete stop.

Forward Rotation Switch Operation

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly to start

the tool slowly.

3. The speed increases with the amount of

depression of the trigger for efficient tightening of screws. The brake operates and the bit stops immediately when the trigger

is released.

4. After use, set the lever to its center posi

tion (switch lock).

CAUTION:

• To eliminate excessive temperature

increase of the tool surface, do not operate the tool continuously using two

or more battery packs. Tool needs cool

off time before switching to another

pack.

Tightening confirmation lamp

• The tightening confirmation lamp can be used to check whether tightening has been

completed properly.

Tool status Lamp display

Tightening complete

(Normal clutch operation)

• Tightening not complete

• Tightening complete without fullling the set

function conditions

The automatic poweroff function has been

activated.

NOTE

• The tightening confirmation lamp will not turn on under the following conditions:

• During reverse rotation operation

• The lamp turns off when the tool is in

operation.

Green (For approx. 2 seconds)

Red (For approx. 2 seconds)

Red (For approx. 5 minutes)

Control Panel

Reverse Rotation Switch Operation

Push the lever for reverse rotation. Check

direction of rotation before use.

Depress the trigger switch slightly to start the

2. tool slowly.

3. After use, set the lever to its center position (switch lock).

(1) (2)

the

(1) The battery indication lamp

• Use the battery indication lamp to check how much power is left in the battery.

• Battery life varies slightly with ambient tem-

perature and battery characteristics. The

lamp is designed to provide a rough indication of remaining battery life.

7 -

EN EN

Indicator Battery status

Fully charged

Approx. 40% or less

remaining

Flashing

Approx. 20% or less

remaining (indicates need to recharge battery)

Flashing

The battery pack will need

to be charged soon. No charge

The battery pack needs to

be charged. (The tool’s automatic

power-off function will

activate at this stage.)

Automatic power-off function

• The automatic power-off function is designed to prevent a loss of tightening torque due to reduced battery voltage. Once it has been activated, the tool will not operate until the battery pack has been charged (or replaced with a fresh unit), even if the trigger is

depressed.

NOTE:

• All 3 bars on the battery indication lamp will flash when the automatic power-off

function is activated.

• When the battery indication lamp begins flashing, the battery pack should be charged (or replaced with a fresh unit)

immediately.

• Be sure to fully charge the battery pack in question after activation of the auto-

matic power-off function. Failure to do

so may prevent the automatic power-off function from being properly deactivated.

• The tool may power off automatically

under heavy work loads.

However the tool will be operational

again after the battery is removed and reinstalled. The battery must have a sufficient charge to re-enable the tool.

(2) LED light

Pressing the button toggles the LED light on

and off.

The light consumes very little power and will not significantly affect battery run time.

CAUTION:

•

The built-in LED light is designed to illuminate the small work area temporarily.

•

Do not use it as a substitute for a regular

flashlight, since it does not have

enough brightness

This tool has the built-in LED light.

Caution: DO NOT STARE INTO BEAM.

Use of controls or adjustments or performance of procedures other than those specied herein

may result in hazardous radiation exposure.

8 -

Tightening Torque Setting

(53.1)

(106.2)

(in·lbs)

1 10 3020 40 50 60

EYFGB3

EYFGB2

EYFGB1

1. Open the shutter with the clutch setting

handle.

Front view of the

main unit

Shutter (closed)

Engage the ribs on the main unit with the

ribs on the clutch setting handle (on the

short side) and turn clockwise.

2. Insert the 3 ribs on clutch setting handle (on the long side) into the shutter holes.

Make sure to insert the wider rib into big

ger hole.

Clutch setting handle

(short side view)

Example-clutch

setting #40

Example-clutch

setting #20

3. Close the shutter with the clutch setting handle by turning counterclockwise.

NOTE:

• Be sure to close the shutter to prevent

dust.

Tightening torque chart (reference values)

This data consists of reference values measured under the conditions described below. During actual work, values will vary based on operating conditions (lock bolt, target substrate, method of securing the bolt in place, etc.).

Measurement conditions

As dened by Panasonic

Bigger hole Wider rib

To set clutch torque, turn the clutch setting

handle clockwise or counterclockwise.

Clutch stage can be set from 1 to 60 stage.

(two full turns)

Decrease torque

Increase torque

9 -

Torque setting level

CAUTION:

• Always check the tool’s tightening

torque before use. Improper tool opera-

tion may result in excessive or inadequate tightening.

• Always operate the tool with the switch fully depressed. The torque accuracy may not be stable if

• the switch is not sufficiently depressed.

•

Use figures from the tightening torque chart to guide your selection of torque clutch setting. (See the tightening torque

chart)

Error Display

EN EN

In the event of a tool or battery pack malfunction, the control panel will display an error message. Please check the tool or battery pack as described in the following chart before having them serviced.

Display Likely cause Corrective action

The battery pack is too hot. Stop work and allow the battery

The tool is too hot to operate. Stop work and allow the tool to

The contacts that connect the battery pack and tool are dirty.

The battery pack has not been properly inserted into the tool.

The pins on either the tool or

battery pack have worn down.

Motor failure, etc. Stop using the tool immediately.

Tool circuit malfunction, failure,

etc.

pack to cool before resuming use

of the tool.

cool before resuming use.

Remove any dirt.

Insert the battery pack rmly into

the tool.

Replace the battery pack.

10 -

11 -

[Battery Pack] For Appropriate Use of Bat-

tery Pack

Li-ion Battery Pack

• For optimum battery life, store the Li-ion battery pack following use without charging it.

• When charging the battery pack, confirm that the terminals on the battery charger are free of foreign substances such as dust

and water etc. Clean the terminals before

charging the battery pack if any foreign sub-

stances are found on the terminals.

The life of the battery pack terminals may be

affected by foreign substances such as dust and water etc. during operation.

• When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a con-

nection from one terminal to another.

Shorting the battery terminals together may

cause sparks, burns or a fire.

• When operating the battery pack, make sure the work place is well ventilated.

• When the battery pack is removed from the main body of the tool, replace the battery pack cover immediately in order to prevent dust or dirt from contaminating the battery terminals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a limited life.

If the operation time becomes extremely short

after recharging, replace the battery pack with

a new one.

Battery Recycling

ATTENTION:

A Li-ion battery that is recyclable powers the product you have purchased.

Please call 1-800-8-BATTERY for information on how to recycle this battery.

[Battery Charger] Charging

Read the operating manual for Panasonic battery charger for the battery pack before charging.

Before charging the battery

Charge the battery at a temperature of 5°C (41°F) to 40°C (104°F).

The battery pack cannot be charged at a tem perature of less than 5°C (41°F). If the

tem perature of the battery pack is less than

5°C (41°F),  rst remove the battery pack from the charger and allow it to sit for an hour in a location where the temperature is 5°C (41°F) or warmer. Then charge the battery pack again.

VI.

MAINTENANCE

Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, benzine, or other volatile solvents for cleaning.

+ 25 hidden pages