Panasonic EYFLA6PR User Manual [en, es, fr]

Operating Instructions

Instructions d’utilisation

Manual de instrucciones

Cordless Impact Driver/Cordless Impact Wrench

Perceuse à impact sans l/Clé de serrage à impact sans l

Destornillador de impacto inalámbrico/Llave de impacto inalámbrica

Model No: EYFLA4A / EYFLA4AR

EYFLA5A / EYFLA5AR EYFLA5Q / EYFLA5QR EYFLA6J / EYFLA6JR EYFLA6P / EYFLA6PR EYFMA1P EYFMA1J

* Pictured: Cordless impact driver

* Image: Perceuse à impact sans l

* En la imagen: Destornillador de impacto inalámbrico

IMPORTANT

This manual contains safety information. Read manual completely before first using this product and save this manual for future use.

IMPORTANT

Ce mode d’emploi contient des informations sur la sécurité. Lisez-le en entier avant d’utiliser le produit et conservez-le pour référence.

IMPORTANTE

Este manual contiene información de seguridad. Lea completamente este manual antes de utilizar por primera vez este producto, y guárdelo para poder consultarlo en el futuro.

Index

English: Page 4 Français: Page 20 Español: Página 38

FUNCTIONAL DESCRIPTION DESCRIPTION DES FONCTIONS DESCRIPCIÓN FUNCIONAL

EYFLA4A/EYFLA4AR EYFLA5A/EYFLA5AR

(I)

(G)(H)

(A)

(E)

(D)

(K)

(J)

(F)

(T)

EYFLA5QR EYFLA5Q

EYFLA6J EYFLA6JR EYFMA1J

(C)

(V) (U)

EYFLA6P EYFLA6PR

EYFMA1P

(L)

(B)

(M)

(N) (O)

(P)

(R)

(Q)

Remote control and battery are not included. La télécommande et la batterie ne sont pas incluses. El control remoto y la batería no están incluídos.

(S)

2 -

6.35 mm - (EYFLA4A, EYFLA4AR/EYFLA5A, EYFLA5AR)/square drive (EYFLA5Q, EYFLA5QR, EYFLA6J, EYFLA6JR, EYFMA1J/pin type EYFLA6P, EYFLA6PR, EYFMA1P/pin-detent type) 6,35 mm -

(A)

EYFLA6JR, EYFMA1J/type à goujon EYFLA6P, EYFLA6PR, EYFMA1P/type à goupille d'arrêt) 6,35 mm EYFLA6JR, EYFMA1J/tipo pasador EYFLA6P, EYFLA6PR, EYFMA1P/tipo pasador retenedor)

Tightening conrmation lamp Témoin de conrmation de serrage

(B)

Lámpara de conrmación de apriete

Alignment mark Marques d’alignement

(D)

Marcas de alineación

Control panel Panneau de commande

(F)

Panel de control

Battery indication lamp Témoin indicateur de la batterie

(H)

Lámpara de indicadora de la batería

Variable speed control trigger Gâchette de commande de vitesse

(J)

Disparador del control de velocidad variable

Pin-detent Goupille d'arrêt

(L)

Pasador retenedor

+ button Bouton +

(N)

Botón +

OK button Bouton OK

(P)

Botón OK (correcto)

Format button Bouton de format

(R)

Botón de formato

Battery Batterie

(T)

Batería

Torque set button Bouton de réglage du couple de serrage

(V)

Botón de ajuste de par de torsión

(EYFLA4A, EYFLA4AR/EYFLA5A, EYFLA5AR)/entraînement carré (EYFLA5Q, EYFLA5QR, EYFLA6J,

(EYFLA4A, EYFLA4AR/EYFLA5A, EYFLA5AR)/excitador cuadrado (EYFLA5Q, EYFLA5QR, EYFLA6J,

Forward/Reverse lever Levier d’inversion marche avant/marche arrière

(C)

Palanca de avance/marcha atrás

Remote control Assembly Qualier Véricateur d'assemblage de la télécommande

(E)

Cualicador incorporado con control remoto

LED light on/off button Bouton Marche/Arrêt de la lumière DEL

(G)

Botón ON/OFF de luz LED

Display

Afchage

(I)

Visor

LED light Lumière DEL

(K)

Luz indicadora

Remote control Télécommande

(M)

Control remoto

− button

Bouton −

(O)

Botón −

Torque level button Bouton de niveau du couple de serrage

(Q)

Botón de palanca de par de torsión

Holder Support

(S)

Retenedor

Interval set button Bouton de réglage de l’intervalle

(U)

Botón de ajuste de intervalo

3 -

GENERAL SAFETY RULES

WARNING! Read all instructions

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool and batt e r y o p e r a t e d (cordless) power tool.

SAVE THESE INSTRUCTIONS

Work Area Safety

1) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

1) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

3) Do not expose power tools to rain or

wet conditions.

Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

A moment of inattention while operating power tools may result in personal injury.

Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

Avoid accidental starting. Ensure the switch is in the off position before plugging in.

Carrying power tools with your finger on the switch or plugging in the power tools that have the switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

Do not over reach. K eep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving parts.

If devic e s ar e prov ided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust related hazards.

Power Tool Use and Care

Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack from

4 -

the power tool before making any adjustments, changing accessories, or storing power tools.

Suc h pr e v entive s afety m easures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.

Use of the power tool for operations differ ent fro m those intend ed could result in a hazardous situation.

Battery Tool Use and Care

1) Ensure the switch is in the off position before inserting battery pack.

Inserting battery pack into power tools that have the switch on invites accidents.

Recharge o nly with the charger specified by the manufacturer.

A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs.

Use of any other battery packs may create a risk of injury and fire.

When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns, or a fire.

Under abusive conditions, liquid may be ejected from battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

Service

1) Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of power tool is maintained.

. INTENDED USE

This tool is a Cordless Impact Driver/Wrench and can be used to tighten bolts, nuts, and screws. Additionally, it provides a torque control function that automatically stops tool operation when a preset load is reached to deliver consistent tightening torque. Additionally, a separately available Assembly Qualier can provide wireless monitoring to determine whether tightening has been completed properly.

Read “the Safety Instructions” booklet and the following before using.

III

ADDITIONAL SAFETY RULES

) Wear ear protectors when using the

tool for extended periods.

2) Be aware that this tool is always in an

operating condition, since it does not have to be plugged into an electrical outlet.

3) Hold power tools by insulated gripping

surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

4) Do NOT operat e the Forward/Reverse

lever when the main switch is on. The battery will discharge rapidly and damage to the unit may occur.

5) During charging, the charger may become

slightly warm. This is normal.

Do NOT charge the battery for a long period.

6) When storing or carrying the tool, set the

Forward/Reverse lever to the center position (switch lock).

5 -

7) Do not strain the tool by holding the speed cont rol trigger half way (sp eed con trol mode) so that the motor stops.

Symbol Meaning

Attaching Socket (Pin type)

• Remove the socket’s rubber ring and pin.

rubber

ring

groove

Revolutions or reciprocations

-1

… min

. ASSEMBLY

Electrical capacity of battery

Volts

Direct current

No load speed

per minutes

pack

Attaching or Removing Bit

NOTE:

•

When attaching or removing a bit, disconnect battery pack from tool or place the switch in the center position (switch lock).

1. Hold the collar of quick connect chuck and pull it out from the tool.

2. Insert the bit into the chuck. Release the collar.

3. The collar will return to its original position when it is released.

Pull the bit to make sure it does not come out.

5. To remove the bit, pull out the collar in the same way.

CAUTION:

• If the collar does not return to its origi

nal position or the bit comes out when pulled on, the bit has not been properly attached. Make sure the bit is properly attached before use.

EYFLA4A/EYFLA4AR/EYFLA5A/EYFLA5AR

12 mm

(15/32")

9 mm – 9.5 mm

(23/64" – 3/8")

6.35 mm (1/4")

1 Attach the socket to the tool. 2 Insert the pin. (Taking care to align the pin

holes on the socket and tool.)

3 Attach the rubber ring by sliding it into place

over the groove.

NOTE:

Be sure to attach the rubber ring to prevent the pin from falling out.

Removing Socket (Pin type)

1 Remove the rubber ring. 2 Remove the pin. 3 Remove the socket from the tool.

NOTE:

Keep the temperature of the tool above

the freezing point (0°C/32°F) when attaching sockets to or detaching them from the square drive on the tool. Do not use excessive force when attaching or detaching sockets.

6 -

Attaching Socket (Pin-detent)

1 Depress the pin-detent on the square drive. 2 Attach the socket to square drive. 3 Make sure the socket is securely attached to

the square drive.

Removing Socket (Pin-detent)

1 Insert a small rod into the hole on the socket. 2

Depress the pin-detent, then detach the socket.

NOTE:

Keep the temperature of the tool above the freezing point (0°C/32°F) when attaching sockets to or removing them from the square drive. Do not use excessive force when attaching or removing sockets.

CAUTION:

• When attaching a socket to the driver, verify that the socket and pin-detent do not interfere with one another.

The pin-detent will be subjected to

excessive force, possibly damaging it.

2 Sockets with a pin hole on one side

only

You may be unable to remove the

socket if it is attached in the wrong orientation.

3 Sockets whose pin holes have bev-

eled edges

The socket will not be held in place

with sufficient force, so that it may come off during use.

Attaching or Removing Battery Pack

1. To connect the battery pack: Line up the alignment marks and attach

the battery pack.

Slide the battery pack until it locks into

• position.

Proper socket attachment

• Some sockets may not function well with the driver due to their shape. Avoid use of sockets such as the following:

1 Sockets shaped so that the pin-detent

makes contact with the side of the socket’s pin hole when the socket is attached to the driver.

7 -

Alignment marks

2. To remove the battery pack:

Approx. 50 cm

Vertically

Forward Reverse

Switch lock

Push up on the button from the front to release the battery pack.

Wireless remote control range

Button

. OPERATION

Before Using the Remote Control (Available as an optional accessory)

Insert the battery

1. Pull out the battery holder. 1 Push in on the fas-

tener as indicated by the arrow.

2 Pull out the holder.

2. Insert the battery and push the holder back in.

NOTE:

• If the tool does not respond to the wire less remote control even when the remote control is operated close to the tool, the battery (CR2025) is dead. Replace it with a fresh battery.

• The included battery is provided for sample use and may not last as long as commercially available batteries.

The remote control should be operated within approximately 50 cm and approximately 60° vertically and horizontally of the perpendicular

relative to the infrared Assembly Qualier on

the tool.

• Under the following circumstances, you may not be able to operate the tool, even within this range.

• If there is an object between the remote control’s transmitter and the tool’s Assembly Qualifier.

• Use outdoors or in other environments where the remote control Assembly Qualifier is exposed to a strong light source, or when the remote control transmitter or Assembly Qualifier is dirty may cause the tool to fail to respond, even when the remote control is used within the operating range.

[Main Body] Switch and Forward/Reverse

Lever Operation

CAUTION:

To prevent dama ge, do not operat e Forward/Reverse lever until the bit comes to a complete stop.

8 -

Forward Rotation Switch Operation

1. Push the lever for forward rotation.

2. Depress the trigger switch slightly to start the tool slowly.

3. The speed increases with the amount of depression of the trigger for efficient tightening of screws. The brake operates and the bit stops immediately when the trigger is released.

4. After use, set the lever to its center posi tion (switch lock).

Reverse Rotation Switch Operation

Push the lever for reverse rotation. Check direction of rotation before use.

Depress the trigger switch slightly to start the

2. tool slowly.

3. After use, set the lever to its center position (switch lock).

CAUTION:

• To elim inate excessive temperature increas e of the tool surface, do not operate the tool continuously using two or more battery packs. Tool needs cool off time before switching to another pack.

Tightening confirmation lamp

• The tightening confirmation lamp can be used to check whether the torque control function was activated.

the

CAUTION:

• When the tool stops automatically after the switch is released during impactmode tightening and then re-engaged within 1 second, the red lamp will light up to indicate the risk of excessive torque application as a result of re-tightening.

NOTE

• The tightening confirmation lamp will not turn on under the following conditions:

• When the torque clutch is set to “F”

• During reverse rotation operation

• The lamp turns off when the tool is in operation.

Control Panel

(1) LED light

(1) (2) (3)

Tool status Lamp display

Tightening complete (with torque control function operation)

• Tightening not complete

• Tightening complete with retightening within 1 second

The automatic stop function has been activated.

Green (For approx. 2 seconds)

Red (For approx. 2 seconds)

Red (For approx. 5 minutes)

Pressing the button toggles the LED light on and off. The light illuminates with very low current, and it does not adversely affect the performance the

tool during use or its battery capacity.

CAUTION:

•

The built-in LED light is designed to illuminate the small work area temporarily.

•

Do not use it as a substitute for a regular

flashlight, since it does not have

enough brightness

This tool has the built-in LED light.

Caution: DO NOT STARE INTO BEAM.

Use of controls or adjustments or performance

of procedures other than those specied herein

may result in hazardous radiation exposure.

9 -

(2) The battery indication lamp

• Use the battery indication lamp to check how much power is left in the battery.

• Battery life varies slightly with ambient temperature and battery characteristics. The lamp is designed to provide a rough indication of remaining battery life.

Battery indication lamp

Indicator Battery status

Fully charged

Approx. 40% or less remaining

Flashing Approx. 20% or less remaining (indicates need to recharge battery)

Flashing

The battery pack will need to be charged soon.

No charge The battery pack needs to be charged. (The tool’s automatic power-off function will activate at this stage.)

Automatic power-off function

• The automatic power-off function is designed to prevent a loss of tightening torque due to reduced battery voltage. Once it has been activated, the tool will not operate until the battery pack has been charged (or replaced with a fresh unit), even if the trigger is depressed.

Battery indication lamp

Indicator

Flashing

NOTE:

• All 3 bars on the battery indication lamp will flash when the automatic power-off function is activated.

• When the battery indication lamp begins flashing, the battery pack should be charged (or replaced with a fresh unit) immediately.

• Be sure to fully charge the battery pack in question after activation of the automatic power-off function. Failure to do so may prevent the automatic power-off function from being properly deactivated.

(3) The torque control function

• The torque control function calculates the load from the motor’s rotational angle during the hammer impact and determines that the bolt has been properly seated when a preset load value is exceeded. Driving is then automatically stopped after a preset number of impacts have been delivered to the bolt.

CAUTION:

• Alw ays ch eck th e tool ’s tightening torque before use. Improper tool operation may result in excessive or inadequate tightening.

CAUTION:

• Always operate the tool with the switch fully engaged. The torque control function will not operate when the switch is not sufficiently engaged, preventing the tool from stopping automatically.

• In work where a heavy load comes to bear during tightening, the load may be interpreted as the seating of the bolt, preventing the bolt from being completely tightened.

• Repeated tightening of the same bolt may break the bolt or deform the material into which the bolt is being driven as a result of excessive tightening.

• The tightening torque value and preci sion vary with factors such as the material into which the bolt is being driven and the condition of the socket being used. Adjust the torque as necessary for the work being performed. Bolt tightening torque varies due to the factors described below.

1) Bolt

• Bolt diameter: Tightening torque generally increases with bolt diameter.

• Torque coefficient (indicated by the bolt manufacturer), grade, length, etc.

10 -

2) Other

3…28

1F30 229

• Bit and socket co ndi tio n: Mater ial , amount of play, etc.

• Use of a unive rsa l joint or socket adapter

• Use r: M ann er in whic h th e tool is applied to the bolt, strength with which the tool is held, manner in which the tool’s switch is engaged

• Condition of object being tightened: Material, seating surface finish

Setting the tool to configuration mode

1. Turn off the control panel.

• If the control panel is on, remove and then reinsert the battery pack.

2. Engage the switch while pushing the button and then release both the button and the switch.

• After all the LED lamps have turned off, the control panel will flash and change to configuration mode.

Configuring the torque clutch setting

(1)

(2)

NOTE:

• Tools ship from the factory set to “F” mode (torque control function off).

• The control panel will turn off if the tool is not operated for a period of 5 minutes.

Display

Battery indication lamp

1. Press the and buttons to select the clutch setting that is appropriate for the work being performed.

11 -

As the button is pressed

• “F” indicates that the torque control function is off.

As the button is pressed

• You can select from 30 torque clutch settings (1 to 30).

• Use figures from the Tightening Torque Chart to guide your selection of torque clutch setting. (See the following tightening torque chart)

2. Press the OK button to accept the select ed torque clutch setting.

• The control panel will stop flashing and light up.

CAUTION:

• You must press the OK button in order for the selected setting to take effect.

• Be sure to verify the new value after changing the setting. (See page 14.)

Setting the snug point detection level

(1)

1. Press the torque setting mode button.

• The snug point detection level setting value will be displayed.

Display

Battery indication lamp

2. Press the and buttons to set the best snug point detection level for the work you’re performing.

Display Snug point detection level

(Use for work characterized by

low loads before the snug point

is reached.)

(Use for work characterized by

high loads before the snug point

is reached.)

(2)

(3)

Low

High

3. Press the OK button to accept the number of torque stages and the snug point detection level.

• The tool’s panel will flash and then light up continuously.

CAUTION:

• Set the snug point detection level from “L1.” Setting the snug point detection level from “L2” may result in cracking or defor mation of the target material.

• If the tool stops before the snug point at snug point detection level “L1,” set the snug point detection level to “L2.”

• Changing the snug point detection level from “L1” to “L2” may increase the torque. Set the number of torque stages again after making this change.

• The setting will not be changed until you press the OK button.

• After changing the setting, be sure to check the new setting value. (See page 14.)

IMPORTANT INFORMATION:

• You can set the snug point detection level and retightening prevention time at the same time by changing the retightening prevention time (see page 13) before pressing the OK button and then pressing the OK button.

• Pressing the torque setting mode but ton toggles the display between the snug point detection level setting value and the number of torque stages setting value.

• The tool shi ps with the snug poin t detection level set to “L1.”

• When the number of torque stages has been set as shown below, the snug point detection level cannot be switched from “L1” to “L2.”

Model

EZFLA4 1 to 8 EZFLA5 1 to 3

Number of torque stages

setting

12 -

Snug point detection level guidelines

100

120

140

1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 16 17 1 8 19 20 2 1 22 23 2 4 25 26 27 2 8 29 30

EYFLA4(M6)

EYFLA6(M8)

EYFLA4(M8)

EYFLA5(M8)

EYFLA6(M10)

EYFMA1(M10)

EYFMA1(M12)

EYFMA1(M14)

EYFLA5(M6)

Display Snug point detection level Applications (reference)

Low

(Use for work characterized by low loads

before the snug point is reached.)

High

(Use for work characterized by high

loads before the snug point is reached.)

• Tightening bolts in materials that are easily cracked or deformed, etc.

• Tightening bolts in materials with mis aligned holes, etc.

• Tightening self-tapping screws, etc.

Tightening Torque Chart (for Reference Use)

The values illustrated on this chart were measured under the conditions described below and are provided for reference purposes. Actual tightening torque varies with ambient conditions (the particular bolt being tightened, hardware being used, method of holding the bolt in place, etc.).

Display

Battery indication lamp

3. Press the and buttons to set the desired time.

Buttons Display Seconds

30 3

1 0.1 0 Off

Measurement conditions

• Temperature: Room temperature (20°C/68°F)

Using the Interval Set

• The interval set operates to prevent the tool from operating after it automatically stops as a result of the torque control function, even if the switch is engaged.

1. Set the tool to configuration mode.

(See page 11.)

2. Press the interval set button.

• The control panel will begin flashing.

Display: The number 0 ashes on and off.

Battery indication lamp: The middle bar

of the battery ashes on and off.

4. Press the OK button to accept the select ed setting.

• The control panel will stop flashing and light up, and the torque clutch setting will be displayed.

CAUTION:

• Be sure to verify the new value after changing the setting.

13 -

Radio signal range limitation function on/off setting (EYFLA4AR, EYFLA5AR, EYFLA5QR, EYFLA6PR)

1. Set the tool to configuration mode. (See page 11.)

2. Press the format button.

• The control panel will begin flashing.

Display: The letter “F” ashes on and off.

Battery indication lamp: The upper and

lower bars of the battery ash on and off.

Display

Battery indication lamp

3. Press the format button again.

• Radio signal range limitation function on/off setting value will be displayed.

4. Press the and buttons to set radio signal range limitation function on/off.

Display

Factory settings

Radio signal

range limitation

function mode

Tool is operational in the

C0 OFF

C1 ON

• Radio signal range limitation function setting: C0 (OFF)

NOTE:

• For more information about how to register the tool and assembly qualifier, see the assembly qualifier instruction manual.

absence of communications with the Assembly

Qualier.

Tool is not operational in the absence of communications with the As-

sembly Qualier.

Status

Initializing All Settings

Factory settings

• Torque clutch setting: “F” (torque con trol function off)

• Interval setting: 0 (off)

• This section explains how to revert all tool settings to their default values at the time of shipment from the factory.

• The error display will be turned off.

1. Set the tool to configuration mode.

(See page 11.)

2. Press the format button.

• The control panel will begin flashing.

Display: The letter “F” ashes on and off.

Battery indication lamp: The upper and

lower bars of the battery ash on and off.

Display

Battery indication lamp

3. Press the OK button to accept the select-

ed setting.

• The control panel will stop flashing and light up.

Checking Tool Settings

• This section describes how to have the tool display current settings for approxim atel y 3 se cond s whe n the tool is stopped.

• You cannot check tool settings when the control panel is turned off. First, engage the switch briefly to reactivate the display.

Checking the sung point detection setting

1. Press the torque set button.

• Control panel display Display: The torque set lights up. Battery indication lamp: The upper and mid-

dle bars of the battery ash on and off.

Checking the interval

1. Press the interval set button.

• Control panel display Display: The interval set lights up. Battery indication lamp: The middle bar

of the battery ashes on and off.

14 -

Checking tool circuits

1. Press the torque level button.

• Control panel display Display: The torque set display lights up. Battery indication lamp: The middle and

lower bars of the battery ash on and off.

Display Tool circuit

H6 EYFLA4

H7 EYFLA5

H8 EYFLA6

H9 EYFMA1

NOTE:

• If you engage the switch while a setting is being displayed, the control panel will revert to the torque clutch setting display.

CAUTION:

• The torque set display is not intended to be used to identify the type of drive component parts (hammer, etc.) used in a particular tool.

Error Display

In the event of a tool or battery pack malfunction, the control panel will display an error message. Please check the tool or battery pack as described in the following chart before having them serviced.

Display Likely cause Corrective action

Setting error Re-initialize the tool using the

The battery pack is too hot. Stop work and allow the battery

The tool is too hot to operate. Stop work and allow the tool to

The contacts that connect the battery pack and tool are dirty.

The battery pack has not been properly inserted into the tool.

The pins on either the tool or battery pack have worn down.

Motor failure, etc. Stop using the tool immediately.

Tool circuit malfunction, failure, etc.

The tool is unable to communicate with the Assembly Quali-

er while the radio signal range

limitation function is on.

remote control. (See page 14.)

pack to cool before resuming use of the tool.

cool before resuming use.

Remove any dirt.

Insert the battery pack rmly into

the tool.

Replace the battery pack.

• Verify tha t the tool has be en properly registered to the Assembly Qualifier.

Verify that the Assembly Qualifi-

• er’s group setting has been configured correctly.

Improve the reception state, for

• example by moving the Assembly Qualifier closer to the tool.

15 -

16 -

[Battery Pack] For Appropriate Use of Bat-

tery Pack

Li-ion Battery Pack

• For optimum battery life, store the Li-ion battery pack following use without charging it.

• When charging the battery pack, confirm that the terminals on the battery charger are free of foreign substances such as dust and water etc. Clean the terminals before charging the battery pack if any foreign substances are found on the terminals.

The life of the battery pack terminals may be

affected by foreign substances such as dust and water etc. during operation.

• When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another.

Shorting the battery terminals together may

cause sparks, burns or a fire.

• When operating the battery pack, make sure the work place is well ventilated.

• When the battery pack is removed from the main body of the tool, replace the battery pack cover immediately in order to prevent dust or dirt from contaminating the battery terminals and causing a short circuit.

Battery Pack Life

The rechargeable batteries have a limited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one.

Battery Recycling

ATTENTION:

A Li-ion battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

[Battery Charger] Charging

Read the operating manual for Panasonic battery charger for the battery pack before charging.

Before charging the battery

Charge the battery at a temperature of 5°C (41°F) to 40°C (104°F).

The battery pack cannot be charged at a temperature of less than 5°C (41°F). If the temperature of the battery pack is less than 5°C

(41°F),  rst remove the battery pack from

the charger and allow it to sit for an hour in a location where the temperature is 5°C (41°F) or warmer. Then charge the battery pack again.

VI.

MAINTENANCE

Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, benzine, or other volatile solvents for cleaning.

VII

. ACCESSORIES

Charger

• EY0L80

• EY0L81

Battery pack

• EYFB30

• EYFB40

Remote control

• EYFA30

Protector for tool

• EYFA01-A (Blue)

• EYFA01-Y (Yellow)

• EYFA01-H (Gray)

• EYFA01-G (Green)

Protector for battery

• EYFA02-H

• EYFA04-H

Assembly Qualier

• EYFRZ01

• EYFR02

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assume continued compliance, install and use in accordance with provided

instructions. Use only the battery pack specied in the instructions. Any changes or modications

not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC ID: O4O-EYFLA IC : 8507A-EYFLA

The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

Panasonic Electric Works Power Tools Co., Ltd. 33, Okamachi, Hikone, Shiga, Japan

17 -

+ 39 hidden pages