Panasonic CQ-CB9900U User Manual

Removable Full Front MP3 WMA CD Player/Receiver with Full Dot Matrix Display and CD Changer Control

CQ-CB9900U

Operating Instructions

≥ Please read these instructions carefully before using this product and save this manual for future use.

CQ-CB9900U

Item Diagram Q’ty

Screw Kit (YEP0FZ2105)

≥ Hex. Nut (5 mm‡)

≥ Tapping Screw

(5 mm‡t16 mm)

≥ Mounting Bolt

(5 mm‡)

≥ Lock Cancel Plate

Rear Support Strap

(YEFG04019)

Removable Face Plate Case

(YEFA131921)

Power Connector

(YEAJ012010)

Item Diagram Q’ty

Remote Control Unit

(YEFX9992663)

Lithium Battery <CR2025>

Instruction kit

≥ Operating Instructions

(YEFM284210)

≥ Warranty Card, etc.

1 set

Mounting Collar

(YEFX0217039)

Trim Plate

(YEFC05650)

Safety Information

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE INCLUDED COMPONENTS.

CAUTION:

THIS PRODUCT IS A CLASS I LASER PRODUCT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Part 15 of the FCC Rules

FCC Warning:

Any unauthorized changes or modiﬁ cations to this equipment would void the user’s authority to operate this device.

NOTICE:

This product has a ﬂ uorescent lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>

Precautions

When Driving

Keep the volume level low enough to be aware of road and trafﬁ c conditions.

When Washing Your Car

Do not expose the product, including the speakers and CDs, to water or excessive moisture. This could cause electrical shorts, ﬁ re, or other damage.

When Parked

Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on.

Use the Proper Power Supply

This product is designed to operate with a 12 V DC, negative ground battery system (the normal system in a North American car).

Disc Mechanism

Do not insert coins or any small objects. Keep screwdrivers and other metallic objects away from the disc mechanism and disc.

Use Authorized Servicenters

This product is made of precision parts. Do not attempt to disassemble or adjust any parts. Please refer to the Servicenter list including with this product for service assistance.

For Installation

This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°.

Note:

≥ The preset memory is cleared to return to the

original factory setting when the power connector or battery is disconnected.

Find the model number and serial number on either the back or bottom of the unit. Please record them in the space below and retain this booklet as a permanent record of your purchase to help with identiﬁ cation in case of theft.

MODEL NUMBER CQ-CB9900U SERIAL NUMBER DATE PURCHASED FROM

Accessories

Panasonic welcomes you to our ever growing family of electronic product owners. We know that

this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family.

64975

Car Audio

SOURCE

MUTE

POWER

RAND

VOL

312

DISPBAND

REP

SET

SEL

SCAN

NUMBER

CQ-CB9900U

Removable Full Front MP3 WMA CD Player/Receiver with Full Dot Matrix Display and CD Changer Control

Note:

≥ The number in parenthesis underneath each accessory part name is the part number for maintenance and

service.

≥ Accessories and their parts numbers are subject to modiﬁ cation without prior notice due to improvements. ≥ Mounting collar 1 and trim plate 7 are mounted on the main unit at shipment (page 50).

CQ-CB9900U

Features

Built-in AM/FM tuner for HD Radio (IBOC system*) broadcasts

Digital broadcasts can now be heard along with conventional analog broadcasts thanks to the incorporation of the IBOC system that adds digital signals to the existing analog radio signals. As a result, during digital reception AM broadcasts take on a sound quality comparable to FM broadcasts, and FM broadcasts have a sound quality on a par with CDs. The station names, call signs, artists and song titles can also be displayed. * “IBOC” stands for In Band On Channel. It refers to

analog digital simulcast broadcasting that uses the double sideband of the existing FM 400 kHz and AM 40 kHz broadcast carrier frequencies.

MP3/WMA Playback from CD-R/RW

You can play your MP3/WMA (Windows Media Audio) ﬁ les as well as regular CDs. With up to 10 to 12 times* the capacity of a conventional CD, a single MP3/WMA-encoded disc can keep you entertained throughout your entire journey. *Depending on bit rate.

SQ7 (7 bands Sound Quality)

SQ is a function that can call up various sound types at the touch of button in accordance with your listening music type. At SQ7, SQ presets 2 to 6 can also be ﬁ nely adjusted as desired (page 32).

HPF (High Pass Filter)/LPF (Low Pass Filter)

Genuine subwoofer system achieved thanks to HPF (High Pass Filter) and LPF (Low Pass Filter)

CD Changer Control

You can connect the optional CD changer unit. For details, refer to the operating instructions on the CD changer unit. ≥ 2 CD changers (option) can be controlled with

this unit. To connect 2 CD changers to it, the dual CD changer selector CA-CD55U (option) is necessary.

Large-sized Volume Control

An large-sized rotary volume control that looks like one belonging to a Hi-Fi audio system is featured.

CQ-CB9900U

CD changer (CX-DP880U, option)

Subwoofer (option)

Dual CD changer selector (CA-CD55U, option)

Stereo power ampliﬁ er (option)

Operations with neither mark can be performed either by the main unit or the remote control unit.

This can only be controlled through

the main unit.

This can only be controlled through

the remote control unit.

Before Reading these Instructions

System Upgrade

Note:

≥ This unit does not support Sirius satellite radio. ≥ You cannot connect CD changer and Sirius

receiver using the dual CD changer selector (CA-CD55U, option).

Today’s AM and FM radio is broadcast in analog, which has lower audio quality and is ﬁ lled with static, hiss, pops and fades. Radio stations have begun a transformation to the world of digital using a new technology called HD Radio™. Today’s analog signals and the new HD Radio digital signals will be transmitted at the same time from AM and FM stations. The radios you use today will continue to function for years, however, new receivers are needed to hear the HD Radio digital signals broadcast from the stations.

Using these new receivers, you can pick up the new HD Radio digital signals at the same place on the dial (106.7 KROQ will be digital 106.7 KROQ broadcasting in HD Radio, 710 WOR will be digital 710 WOR broadcasting in HD Radio). Your favorite HD Radio digital station will be right where you left it. Additionally, new HD Radio receivers will still pick up stations broadcasting in analog, so you don’t need two radios.

The beneﬁ ts of digital far outweigh old analog technology. HD Radio makes radio “fun” again. FM digital will sound like a CD throughout the coverage area, and AM digital will sound like today’s FM throughout the coverage area, both without the static, hiss, pops or fades that you’ve had to put up with for almost a century.

While HD Radio will bring you pristine audio quality, it will also provide data services*. Both AM and FM HD Radio stations will transmit song and artist title, trafﬁ c updates, weather alerts, news reports and much more. For more information, visit www.hd-radio.com. Stay tuned!

* This unit supports text displays for the following

items; station name, call sign, artist, song title.

What is HD Radio™?

HD Radio broadcasts can be enjoyed only in those areas in the United States where the broadcasts can be received. This means that the HD Radio feature cannot be used outside the U.S. or in areas inside the U.S. where these broadcasts cannot be received. (as of December 2003)

HD Radio is a trademark of iBiquity Digital Corporation.

CQ-CB9900U

Preparation

Battery Installation

1 Remove the battery holder.

Pull the holder out at position B while pushing

position A as indicated.

2 Install the battery on the battery holder.

3 Insert the battery holder back into its original

position.

Battery Notes

≥ Battery type: Panasonic lithium battery (CR2025)

(included)

≥ Battery life: Approximately 6 months under

normal use (at room temperature)

≥ Remove and dispose of an old battery

immediately.

≥ Do not disassemble or short the battery. Do not

throw a battery into a ﬁ re.

≥ Keep the battery away from children to avoid the

risk of accidents.

≥ Follow local regulations when disposing of the

battery.

Back side

Lithium battery (included)

Battery holder

Position A

Position B

Remote Control Unit

Caution:

≥ Improper use of the battery may cause

overheating, an explosion or ignition, resulting in injury or a ﬁ re.

Subwoofer

Preparation:

≥ Connect the subwoofer and the ampliﬁ er (option)

(page 60).

Subwoofer level setting:

≥ You can change the subwoofer level (page 34).

Subwoofer low pass ﬁ lter setting:

≥ You can select the upper limit frequency of the

sound from subwoofer (page 34).

The 12-hour system is used for the clock.

≥ Turn your car’s ignition key to the ACC or ON

position.

≥ Press [SOURCE] (PWR). ≥ When the power is switched on for the ﬁ rst

time, a demonstration appears on the display. Press [DISP] (display) to change to regular mode (page 10).

1 Press [MENU].

Press and hold [MENU] for more than

2 seconds.

2 Press [$] to select “DISPLAY”.

3 Press [#] to select “CLOCK ADJ”.

4 Press [SET].

5 Setting.

Hours:

1 Press [%]. The hour display hilights.

2 Press ["]: Put forward 3 Press [#]: Put back

Minutes:

1 Press [$]. The Minutes display hilights.

2 Press ["]: Put forward 3 Press [#]: Put back

6 Complete.

Press [SET].

Note:

≥ Press and hold ["] or [#] to change numbers

rapidly.

Clock Setting

CQ-CB9900U

Audio Settings....................................................... 32

Volume, bass/treble, SQ adjustment, balance/fader, subwoofer level, subwoofer low pass ﬁ lter (LPF), high pass ﬁ lter (HPF)

Display Settings..................................................... 36

Background display selection (GRAPHIC PATTERN), contrast, clock adjustment

Function Settings ................................................... 38

Mute/attenuation, security function

Troubleshooting..................................................... 40

Preliminary steps, if you suspect something wrong, troubleshooting tips, error display messages, maintenance, product servicing, fuse

Notes on Discs ...................................................... 48

Notes on CD/CD media (CD-R, CD-RW, CD-ROM), notes on CD-Rs/RWs

Anti-Theft System................................................... 49

Remove the removable face plate, install removable face plate, security indicator, panel removal alarm

Installation Guide................................................... 50

Electrical Connections ............................................. 56

Wiring diagram, upgrading the system 1, upgrading the system 2, speaker system connection

Speciﬁ cations ....................................................... 61

Safety Information .................................................................................Page 2

Precautions.................................................................................................... 2

Accessories........................................................... 3

Features................................................................4

What is HD RadioTM?

Before Reading these Instructions ................................ 5

Preparation ........................................................... 6

Remote control unit, subwoofer

Clock Setting ......................................................... 7

General............................................................... 10

Power, source, volume, mute/attenuation, dimmer, rear speakers as sub-woofers (super bass control subwoofer/SBC-SW), SQ (Sound Quality), display change

Radio ................................................................. 14

Radio mode, band, reception mode, tuning, seeking, station preset, preset station calling, text display

Before Disc Playback............................................... 18

Available discs, disc insert, when CD is in the player, disc eject

CD Player ............................................................ 19

Track selection, fast forward/fast reverse, pause, scan play, direct track selection, text display, random play/repeat play

MP3/WMA Player ................................................... 22

Folder selection, ﬁ le selection, fast forward/fast reverse, pause, text display, scan play, folder scan play, direct ﬁ le selection, direct folder selection, random play/repeat play, notes on MP3/WMA

CD Changer Control ................................................ 28

CD changer mode, disc selection, track selection, fast forward/fast reverse, scan play, disc scan play, CD changer selection, direct disc selection, random play/repeat play

WELCOME

MP3/WMA

Contents

CQ-CB9900U

Volume

Note:

≥ The volume level can be set independently for

each source (for radio, one volume setting for AM, one volume setting for all FMs).

Setting range: 0 to 40 (default: 18)

[VOL "]: Up [VOL #]: Down

Down

General

SourcePower

Turn your car’s ignition key to the ACC or ON position.

ON: Press [SOURCE] (PWR).

OFF: Press [SOURCE] (PWR) again and hold for

more than 1 second.

Press [SOURCE] (POWER) again and hold

for more than 1 second.

Note:

≥ After turning off the ignition key, a security

message is displayed, and the panel removable alarm that reminds you to take the panel is activated. (When security function is set to on, page 38)

ACC

Demonstration:

When the power is switched on for the ﬁ rst time, a demonstration appears on the display. Press [DISP] (display) to change to regular mode.

Note:

≥ To display the demonstration again, press and

hold [SOURCE] for more than 4 seconds when turning power on.

64975

Car Audio

SOURCE

MUTE

POWER

RAND

VOL

312

DISPBAND

REP

SET

SEL

SCAN

NUMBER

[DISP]

(Display)

[SOURCE]

(Power/source)

[MUTE]

(Mute/attenuation) (SBC-SW)

[VOL "]

[VOL #]

(Volume)

[SOURCE] (PWR: Power)

Press [SOURCE] to change the source.

[MUTE] (Mute/attenuation) (SBC-SW)

[VOLUME]

[DISP] (Display)

Point the remote control unit at the remote control signal sensor.

Rear Speakers as Sub-Woofers

(Super Bass Control Subwoofer/ SBC-SW)

You can utilize the rear speaker connected to the built-in ampliﬁ er as Sub-Woofers that output only bass. (Default: OFF)

Press and hold [MUTE] (SBC-SW) for more than 2 seconds.

When a CD is in the player.

Radio (page 14)

CD player (page 19)

When a MP3 data disc is in the player.

MP3 player (page 22)

When an optional CD changer is connected.

CD changer control (page 28)

AUX (page 57)

When a WMA data disc is in the player.

WMA player (page 22)

OFF (default)

Note:

≥ When ON has been selected, the settings resulting

from the adjustments performed at the subwoofer level and subwoofer low pass ﬁ lter settings are reﬂ ected in the output.

≥ Depending on the speakers used and the type of

music played, it may not be possible to achieve a satisfactory effect.

lights.

Mute/Attenuation

ON: Press [MUTE]. OFF: Press [MUTE] again.

You can select mute or attenuation (page 38).

No sounds. (default)

Decrease the volume by 10 steps.

Dimmer

Press and hold [MENU] (DIM) for more than 2 seconds to change dimmer level setting as follows.

Brighter (default)

Medium

Darker

[MENU] (DIM)

CQ-CB9900U

General

(continued)

[SQ] (Sound Quality)

Display Change

Press [DISP] (display).

∫ When Power is ON

Mode display

Folder hierarchy display (MP3/WMA only)

Mode and Moving picture display/ SA display (page 37)

Moving picture/ SA display (page 37)

Mode and clock display

Display and light off

Clock display

Display and light off

∫ When Power is OFF

Note:

Displays before adjusting the clock (page 7).

≥ Set the background display (GRAPHIC PATTERN)

in a separate procedure (page 36).

≥ “––:––” will appear before adjusting the clock on

the right corner of the mode display.

[DISP] (Display)

SQ is a function that can call up various sound types at the touch of button in accordance with your listening music type. At SQ7, SQ presets 2 to 6 can also be ﬁ nely adjusted to suit the acoustic characteristics inside the car and the user’s preference (page 32).

Press [SQ] to select a sound types as follows.

SQ7 lights (except FLAT).

Note:

≥Press [DISP] (display) to return to the regular

mode.

≥ If no operation takes place for more than

5 seconds, the display returns to the regular mode.

≥ Setting of SQ, bass/treble and volume are

inﬂ uenced one another. If the inﬂ uence mentioned above causes distortion to the audio signal, readjust bass/treble or volume (page 32).

≥ After pressing [SQ] on the main unit, you

can also select a sound type by pressing the preset buttons [1] to [6].

Flat frequency response not emphasize. (default)

Prevention of excessive equalizing and capability to cover wide variety of music. Listener-friendly and crisp sound.

Sharp and dynamic sound. Powerful deep bass and turgescent treble.

Highlighted vocals that are apt to be overwhelmed by instrumental sound.

Sound with emphasis on sharpness of high-hat and echo of saxophone. Jazz-speciﬁ c deep sound.

Reproduction of realism being in a club.

FLAT

ROCK

POP

VOCAL

JAZZ

CLUB

SQ (Sound Quality)

64975

Car Audio

SOURCE

MUTE

POWER

RAND

VOL

312

DISPBAND

REP

SET

SEL

SCAN

NUMBER

[DISP]

(Display)

[1] to [6] (SQ preset buttons)

CQ-CB9900U

Radio

[%] [$] (TUNE)

[D/A] (Digital*/Analog) *This indicates HD Radio.

[SOURCE]

64975

Car Audio

SOURCE

MUTE

POWER

RAND

VOL

312

DISPBAND

REP

SET

SEL

SCAN

NUMBER

[SOURCE]

[%] [$]

(Tuning)

[BAND]

Stereo indicator

This lights when a stereo broadcast is received.

Radio Mode

Press [SOURCE] to select the radio mode.

Radio mode display

Reception Mode

Press [D/A] to select the reception mode.

FrequencyBand

Band

Press [BAND].

FM1

Tuning

[$]: Higher frequency [%]: Lower frequency

AUTO mode** (“AUTO” lights.)

Selects analog or digital reception (HD Radio) automatically. (default)

Seeking

When the reception mode is “AUTO”:

1 Every time you press and hold [D/A] for more

than 2 seconds, Seeking mode is switched as follows;

2 Press and hold [%] or [$] for more than

0.5 seconds, then release. Seeking will start.

When “Auto seeking” is selected: The tuning automatically stops at the stations, whether analog or digital, whose signals can be received, and the signals from those stations are received.

When “Digital seeking” is selected: The tuning automatically stops only at the stations which are airing digital broadcasts, and the signals from those stations are received. The seeking operation is repeated if no digital broadcasts are being aired.

When the reception mode is “ANALOG”:

Press and hold [%] or [$] for more than

0.5 seconds, then release. Seeking will start.

Auto seeking (default)

Digital seeking

This lights when the broadcast station now being received is an HD Radio station (one which is airing a digital broadcast).

ANALOG mode

Selects analog reception only.

** Identifying whether a broadcast

is digital or analog in the AUTO mode

When “DIGITAL” is displayed: This means that digital sound is now being output. (It is displayed while a digital broadcast is being received.)

When “ANALOG” is displayed: This means that analog sound is now being output. (It is displayed while an analog broadcast is being received.)

Note:

≥ Even when the AUTO mode is established and the

HD indicator is lighted:

· The sound may not switch over to digital if the

program concerned (such as a live baseball game) is being broadcast in real time.

· Analog sound will be output if the reception is

poor.

≥ In the AUTO mode, analog sound is output

immediately after the frequency has been tuned in. When listening to analog sound, the sound quality will be better in the ANALOG mode.

FM2

FM3

Note:

≥ Digital seeking may take some time. ≥ Seeking may not stop at stations which are

scheduled to go all-digital broadcasts in the future.

D·SEEK indicator This lights when digital seeking is selected.

This lights when reception mode is “AUTO”.

This lights when a digital broadcast is being received in AUTO mode.

[BAND]

CQ-CB9900U

* Press and hold [SQ] (SCROLL) for more than

2 seconds to have an another circle scroll when the text is displayed.

Note:

≥ If any of the following screens are displayed, the

display will not be switched even when the above operation is performed.

· Mode and Moving picture display/SA display

· Moving picture display/SA display

· Mode and clock display

· Display and light off ≥ There is a case that text is not always displayed

while a digital station is received.

Radio

(continued)

[SQ] (SCROLL)

[DISP] (Display)

64975

Car Audio

SOURCE

MUTE

POWER

RAND

VOL

312

DISPBAND

REP

SET

SEL

SCAN

NUMBER

[DISP]

(Display)

Note: ≥ When pressing [MENU] (pressing and hold

[MENU] for more than 2 seconds on the remote

control unit) in radio mode, the following display appears.

This is because radio mode does not have any

menu settings.

Station Preset

Up to 6 stations can be stored in each of the FM1, FM2, FM3 and AM band selections.

Auto Preset Memory (APM)

Automatically save stations with good reception in the preset memory.

1 Select a band (page 14).

2 Press and hold [BAND] (APM: Auto Preset

Memory) for more than 2 seconds.

[AUTO mode (Auto seeking)]

≥ The stations that broadcast digital signals

are stored in the memory in sequence with the station featuring the best reception ﬁ rst and starting with the highest preset number whereas the stations that broadcast only analog signals are stored in the memory in sequence starting with the lowest preset number.

[AUTO mode (Digital seeking)]

≥ The stations that broadcast digital signals

are saved in sequence with the one featuring the best reception ﬁ rst. (This may take some time.)

[ANALOG mode] ≥ The 6 stations with good reception will be

automatically saved in the memory under preset number 1 to 6.

Once set, the preset stations are sequentially

scanned for 5 seconds each (scanning).

Manual Preset Memory

Manually save a station in the preset memory.

1 Select a band and frequency (page 14).

2 Press and hold ["] or [#] until the preset

number blinks.

3 Press ["] or [#] to select the preset number

(1 to 6).

4 Press and hold ["] or [#] for more than

2 seconds to memorize.

≥ The display blinks once, and a receiving station

is saved in the memory.

1 Select a band and frequency

(pages 14-15).

2 Press and hold [1] to [6] for more than

2 seconds to memorize.

Preset Station Calling

1 Select a band (page 14).

2 Press ["] or [#].

Press [1] to [6].

Note:

≥ Analog sound is heard during scanning.

Text Display

While a digital station is received and the mode display (page 13) is displayed, the display is switched by one step as shown below each time [DISP] (display) is held down for at least 2 seconds.

Station name* (default)

Mode display

Song title*/ Artist name*

[BAND] (APM: Auto Preset Memory)

["] [#]

(Preset station)

[1] to [6] (Preset station)

[BAND]

(Auto Preset Memory)

["] [#]

(Preset station)

CQ-CB9900U

Disc Insert

1 Press [OPEN].

2 Insert a disc.

≥ Playback will start automatically after recognizing

the data of the loading disc.

≥ It may take some time to start playing.

Note:

≥ Do not insert a disc when the disc indicator lights

because a disc is already loaded.

Before Disc Playback

Track Selection

[9]: Next track [:]: Beginning of the current track

For the previous track, press twice.

Fast Forward/Fast Reverse

Press and hold

[9] (5): Fast forward [:] (6): Fast reverse

Release to resume the playback.

Pause

Press [;/1]. Press [;/1] again to cancel.

Scan Play

The ﬁ rst 10 seconds of each track is played in sequence.

Press [5] (SCAN). lights.

Press [5] (SCAN) again to cancel.

Direct Track Selection

Example: track number 10

1 Press [ﬂ]. 2 Press [1] [0]. 3 Press [BAND] (SET).

Note:

≥ To suspend direct selection, press [DISP]

(display) or [ﬂ].

≥ Random, scan and repeat play are canceled once

[ﬂ] is pressed.

Text Display

Press and hold [DISP] (display) for more than 2 seconds in the mode display.

Note:

≥ The power will be turned on automatically when

a disc is loaded.

A disc which has both CD-DA data and

MP3/WMA data on it may not be reproduced normally. (For example, it may be reproduced without sound.)

≥ Refer to the section on “Notes on MP3/WMA”

(page 26) and “Notes on Discs” (page 48).

CD Player

Do not watch the scroll display while driving.

[OPEN]

[:]/[9] (6/5)

(Track selection/fast forward/fast reverse)

[SOURCE]

[BAND]

(;/1: Pause) (SET)

[0] to [9] (Track number)

[5] (Scan play) [6] [5]

(Track selection/fast forward/fast reverse)

64975

Car Audio

SOURCE

MUTE

POWER

RAND

VOL

312

DISPBAND

REP

SET

SEL

SCAN

NUMBER

[DISP]

(Display)

[SOURCE]

[BAND]

(Pause) (SET)

[ﬂ]

(Number)

Available Discs

∫ CD-DA

∫ MP3/WMA

(Example: CD-DA)

* Press and hold [SQ] (SCROLL) for more than

2 seconds to have an another circle scroll when a title is displayed.

Note:

≥ “NO TEXT”: Displays when there is no text.

*Disc/track title (default)

Mode display

[DISP] (Display)

When CD is in the Player

Press [SOURCE] to select the CD (MP3/WMA) player mode and playback starts.

Disc Eject

1 Press [OPEN]. 2 Press [<] (eject) and take the disc. 3 Close the front panel manually.

This instructions on this page are followed for both CD-DA playback and MP3/WMA playback.

Disc indicator

Label side

Close.

[<] (Eject)

Caution: ≥ 3q (8 cm) CD is not available for this unit, so

do not insert it.

≥ Do not use irregularly shaped discs. ≥ Do not use discs that have a seal or label

attached.

≥ Be sure to close the front panel while CD

playback.

≥ To avoid damaging the front panel, do not push

it down or place objects on it while it is open.

≥ Do not pinch your ﬁ nger or hand in the front

panel.

≥ Do not insert foreign objects into the disc slot.

[SQ]

(SCROLL)

Disc indicator lights when the disc is loaded.

+ 22 hidden pages