Panasonic CQ-C1321NE, CQ-C1311NE, CQ-C1301NE Service Manual

ORDER NO. ACED041284C8
AUTOMOTIVE AFTERMARKET
CQ-C1321NE CQ-C1311NE CQ-C1301NE
WMA MP3 CD Player/Receiver
Specifications*
General
Power Supply DC 12V (11V - 16V),
Test Voltage 14.4V Negative Ground
Current Consumption Less than 2.2A (CD mode ; 0.5W
4-channels) Maximum Power Output 50W×4ch (at 1kHz) Tone Adjustment Range Bass ; ±12dB at 100Hz
FM Stereo Radio
Frequency Range 87.5MHz - 108MHz Usable Sensitivity 6dB/µV (S/N 30dB) Stereo Separation 35dB (1kHz)
AM (MW)
Frequency Range 531kHz - 1,602kHz Usable Sensitivity 28dB/µV (S/N 20dB)
AM (LW)
Frequency Range 153kHz - 279kHz Usable Sensitivity 32dB/µV (S/N 20dB)
CD Player
Sampling Frequency 8 Times Oversampling DA Converter 1bit DAC System Pick-Up Type Astigma 3-beam Light Source Semiconductor Laser Wave Length 790nm Frequency Response 20Hz to 20,000Hz (±1dB) Signal to Noise Ratio 96dB Total Harmonic Distortion 0.01% (1kHz) Wow and Flutter Below measurable limits Channel Separation 75dB
Dimensions** 178×50×160mm Weight** 1.4kg
* Specifications and the design are subject to possible modification without notice due to improvements.
** Dimensions and Weight shown are approximate.
Above specifications comply with EIA standards.
• •
© 2 004 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
CONTENTS
Page Page
1 ABOUT LEAD FREE SOLDER (PbF) 3 2 LASER PRODUCTS 3 FEATUERS 4 REPLACING THE FUSE 5 MAINTENANCE 6 NOTES 7 DIMENSIONS 8 WIRING CONNECTION 9 TERMINALS DESCRIPTION
10 PACKAGE AND IC BLOCK DIAGRAM 11 REPLACEM ENT PARTS LIST
3 3
12 EXPLODED VIEW (Unit)
3
13 CD PLAYER PARTS LIST 14 EXPLODED VIEW (CD Deck)
3 3
15 WIRING DIAGRAM
3
16 SCHEMAT IC DIAGRAM 17 BLOCK DIAGRAM
4 5
8 11 15 16 19 20 25 29
2
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
1 ABOUT LEAD FREE
SOLDER (PbF)
Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF
stamp on the PCB.
Caution :
Pb free solder has a higher melting point than standard
• •
solder; Typically the melting point is 50 - 70°F (30 ­40°C) higher. Please use a soldering iron with temperature control and adjust it to 700 ± 20°F (370 ± 10°C). In case of using high temperature soldering iron, please be careful not to heat too long.
Pb free solder will tend to splash when heated too high
• •
(about 1100°F/600°C)
This lead free solder will be used for the products after
• •
serial No. 1,000,001.
2 LASER PRODUCTS
3 FEATUERS
Digital servo for reliable playback.
• •
PLL (Phase Locked Loop) synthesized tuning.
• •
18-FM, 6-AM presets with preset scan.
• •
Removable face plate.
• •
MP3/WMA Playback from CD-R/RW.
• •
CD Changer Control.
• •
4 REPLACING THE FUSE
Use fuses of the same specified rating (15amps). Using different substitutes or fuses with higher ratings, or connecting the product directly without a fuse, could cause fire or damage to the stereo unit.
5 MAINTENANCE
Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry, a soft cloth for routine exterior cleaning. Never use benzine, thinner or other solvents.
6 NOTES
[RADIO BLOCK]
Do not align the AM/FM package block. When the package block is necessary, it will be supplied already aligned at the factory.
[CD DECK BLOCK]
This model has no servo alignment points because microcomputer controls the servo circuit.
7 DIMENSIONS
3
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
8 WIRING CONNECTION
4
9 TERMINALS DESCRIPTION
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
9.1. Main Block
IC601 : YESAM281
Pin No.
1 (NC) - - - - ­2 VSM Radio signal strength I 0 0 0 3 SD/ST Radio station detect I 0.3 0 0.8 4 AVSS Ground - 0 0 0 5 SCL Audio control serial clock O 4.9 4.9 4.9 6 SDA Audio control data O 4.9 4.9 4.9 7 AVREF (Conecting to +5V) - 4.9 4.9 4.9 8 CD SO CD data output I 2.1 2.3 1.7
9 CD SI CD data input O 0 0 3.3 10 CD SCK CD clock O 4.7 4.7 4.7 11 CDC DATA/
12 XM-RX SI (NC) - - - - ­13 CDC CLK (NC) - - - - ­14 CDC REM (NC) - - - - ­15 BZ OUT Buzzer out O 4.4 4.4 4.4 16 LCD DO LCD data I 4.8 4.8 4.8 17 LCD DI LCD data O 4.7 4.7 4.7 18 LCD CLK LCD Clock O 4.8 4.8 4.8 19 CD MUTE CD mute I 0 0 4.8 20 CD RST CD reset O 4.8 4.8 4.8 21 CD STB CD strobe I 3.7 3.7 3.7 22 CDC SENS
23 PLL DO PLL data I 4.9 4.9 4.9 24 PLL CLK PLL data clock O 4.8 4.8 4.8 25 PLL DI PLL data O 0 0 0 26 PLL CE PLL chip select O 0 0 0 27 (NC) - - - - ­28 (NC) - - - - ­29 (NC) - - - - ­30 (NC) - - - - ­31 (NC) - - - - ­32 (NC) - - - - ­33 VSS1 Ground - 0 0 0 34 RDS DATA RDS data I 0 0 0 35 S-LED LED control O 0 0 0 36 LCD CE LCD chip enable O 0 0 0 37 LCD 5V CNT Display 5V control O 0 0 0 38 EJ ILL (NC) - - - - ­39 OP/CL (NC) - - - - ­40 (NC) - - - - ­41 EJECT (NC) - - - - ­42 ROTARY 1 Rotary encoder input 1 I 4.8 4.8 4.8 43 ROTARY 2 Rotary encoder input 2 I 4.7 4.7 4.7 44 (NC) - - - - ­45 (NC) - - - - ­46 PANEL Panel detection I 4.6 4.6 4.6 47 STBY Power IC stundby control O 4.8 4.8 4.8 48 EEPROM CE (Not Used) - - - ­49 EEPROM SK
50 EEPROM DI
51 EEPROM DO (Not Used) - - - ­52 CDC1/2 (NC) - - - - ­53 INV CNT Illumination control O 4.8 4.8 4.8 54 AMP CNT Amp power control O 4.8 4.8 4.8 55 ANT CNT Antenna power control O 4.8 4.8 4.8 56 EXT.MUTE External mute O 4.8 4.8 4.8
Port Description I/O (V)
FM AM CD
- - - - ­XM-TX SO (NC)
- - - - ­(NC)
- - - - ­(NC)
- - - - ­(NC)
Pin No.
57 MAIN CNT Main power control O 4.8 4.8 4.8 58 AMP MUTE Amp mute control O 4.8 4.8 4.8 59 AF MUTE AF mute control O 4.8 4.8 4.8 60 RESET Reset I 4.8 4.8 4.8 61 RDS CLK RDS clock I 0 0 0 62 (NC) - - - - ­63 (NC) - - - - ­64 RM DATA Remote control data I 4.8 4.8 4.8 65 BATT Battery voltage detection I 4.5 4.5 4.5 66 CDC STB/
67 VSS0 Ground - 0 0 0 68 VDD1 +5V power supply - 4.8 4.8 4.8 69 X2 Crystal oscillator - 2.9 2.9 2.9 70 X1 Crystal oscillator - 2.3 2.3 2.3 71 TEST (TEST terminal) - 0 0 0 72 XT2 Crystal oscillator - 2.7 2.7 2.7 73 XT1 Crystal oscillator - 2 2 2 74 VDD0 +5V power supply - 4.9 4.9 4.9 75 AVDD +5V power supply - 4.8 4.8 4.8 76 INI A Mode setting A I 0 0 0 77 INI B Mode setting B I 4.8 4.8 4.8 78 ACC ACC detection I 4.9 4.9 4.9 79 (NC) (Connecting to ground) - 0 0 0 80 LEVEL (Connecting to ground) - 0 0 0
Port Description I/O (V)
XM DET
CD Changer strobe/ XM receiver detection
FM AM CD
I 4.8 4.8 4.8
9.2. Display Block
IC901 : YEAMLC75854T
Pin
No.
1-39 SEG1-39 LCD segment data O 2.5 40-43 COM1-4 LCD common O 2.5 44,45 SEG40,41 Not used - ­46-49 KS3-6 Key scan O 5.0 50-54 Kl1-5 Key data I 0
55 TEST (Connecting to ground) - 0 56 VDD +5V power supply - 5.0 57 VDD1 VDD1 filter terminal - 3.3 58 VDD2 VDD2 filter terminal - 1.7 59 VSS Ground - 0 60 OSC Oscillator terminal - 3.9 61 DO Key data output O 5.0 62 CE LCD driver chip enable I 0 63 CLK LCD clock I 4.9 64 DI LCD data I 4.9
Port Description I/O (V)
5
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
9.3. CD Servo Block
IC401 : YESAM275
Pin No.
Port Descriptions I/O (V)
1 CVSS1 GND - 0 2 - - - ­3 CVSS2 GND - 0 4 DVDD1 I/O system (3.3V) power supply - 3.3 5 A10 Address bus of FLASH ROM O 0 6 - - - ­7 A11 Address bus of FLASH ROM O 3.3 8 A12 O 3.3
9 A13 O 3.3 10 A14 O 3.3 11 A15 O 3.3 12 /CVDD1 CORE CPU system (1.6V) power
supply 13 - - - ­14 DVSS1 GND - 0 15 CVSS3 GND - 0 16 /CVDD2 I/O system (3.3V) power supply - 1.6 17 - - - ­18 - - - ­19 READY - - 3.3 20 /PS FLASH ROM selection signal O 3.3 21 - - - ­22 - - - ­23 R/W Lead/light signal to FLASH ROM O 3.3 24 /MSTRB Memory access signal O 3.3 25 - - - ­26 /MSC - - 3.3 27 MUTE Mute signal output (H:Mute on) O 0 28 - - - ­29 - - - ­30 /HOLD - - 3.3 31 BIO SUBO input I 0 32 MP/MC Operation mode setting (external pull-
up) 33 DVDD2 I/O system (3.3V) power supply - 3.3 34 CVSS4 GND - 0 35 BD R1 GND I 0 36 - - - ­37 CVSS5 GND - 0 38 - - - ­39 - - - ­40 DVSS2 GND - 0 41 CLK C M AUDIO bit clock input I 1.6 42 SCK Clock input I 3.3 43 LRCK CMAUDIO L/R identifying signal input I 1.6
44 CDFS Serial frame sink signal input I 2.6 45 DATACMAUDIO serial data input I 1.6
46 - - - ­47 SI Serial data input I 0 48 CLK M C AUDIO bit clock output O 1.6 49 SCK Clock input I 3.3 50 CVSS6 GND - 0 51 - - - ­52 CVDD3 CORE CPU system (1.6V) power
supply 53 LRCK MCAUDIO L/R identifying signal output O 1.6
54 CDFS Serial frame sink signal input I 2.4 55 - - - ­56 DVDD3 I/O system (3.3V) power supply - 3.3 57 DVSS3 GND - 0
- 1.6
I 3.3
- 1.6
Pin
No.
100 D1 I/O 0 101 D2 I/O 0 102 D3 I/O 0 103 D4 I/O 0 104 D5 I/O 0 105 A16 Address bus of FLASH ROM O 0 106 DVSS7 GND - 0 107 A17 Address bus of FLASH ROM O 3.3 108 A18 O 0 109 A19 Address bus of FLASH ROM O 0 110 A20 O 0 111 CVSS9 GND - 0 112 DVDD5 I/O system (3.3V) power supply - 3.3 113 D6 Data bus of FLASH ROM I/O 0 114 D7 I/O 0 115 D8 I/O 0 116 D9 I/O 0 117 D10 I/O 0
Port Descriptions I/O (V)
58 RESTSWMechanics deck REST SW input I 3.3
59 DATA MCAUDIO serial data output O 1.6
60 SO Serial data output O 1.2 61 - - - ­62 - - - ­63 /NMI - - 3.3 64 /INT0 - - 3.3 65 /INT1 - - 3.3 66 BLKCK Subcode block clock pulse input I 0 67 /INT3 - - 3.3 68 CV DD4 CORE CPU system (1.6V) power
69 SW1 Mechanics deck SW1 input I 0 70 CVSS7 GND - 0 71 MCLK Clock output (To Servo DSP) O 3.3 72 DVSS4 GND - 0 73 MLD Command load signal output (To
74 MDATA Command data output (To Servo
75 DVDD4 I/O system (3.3V) power supply - 3.3 76 DVSS5 GND - 0 77 CLK MD1 Clock mode setting (L fixation) I 0 78 CLK MD2 Clock mode setting (H fixation) I 3.3 79 CLK MD3 Clock mode setting (L fixation) I ­80 - - - ­81 SW2 Mechanics deck SW2 input I 0 82 - - - ­83 EMU0 - - 0 84 EMU/OF
F 85 TDO - - 3.3 86 TDI - - 0 87 /TRST - - 3.3 88 TCK - - 0 89 TMS - - 3.3 90 CVSS8 GND - 3.3 91 CVDD5 CORE CPU system (1.6V) power
92 HPIENA GND I 1.6 93 DVSS6 GND - 0 94 - - - ­95 CLKENA Oscillation output Cainabl signal O 3.3 96 X1 Crystal Connection O 0 97 X2/CLKIN Crystal Connection I 0 98 RS Reset signal input I 1 99 D0 Data base of FLASH ROM I/O 3.4
supply
Servo DSP)
DSP)
- - 3.3
supply
- 1.6
I 3.3
O 3.3
- 0
6
Pin
Port Descriptions I/O (V)
No. 118 D11 Data bus of FLASH ROM I/O 0 119 D12 I/O 0 120 STAT Status signal input I 0.4 121 D13 Data path of FLASH ROM I/O 0 122 D14 I/O 0 123 D15 I/O 0 124 - - - ­125 CVDD6 CORE CPU system (1.6V) power
- 1.6
supply 126 CVSS10 GND - 0 127 - - - ­128 DVSS8 I/O system (3.3V) power supply - 0 129 - - - ­130 DVDD6 I/O system (3.3V) power supply - 3.3 131 A0 Address bus of FLASH ROM O 0 132 A1 O 0 133 A2 O 3.3 134 A3 O 3.3 135 /RST Reset signal output(To Servo DSP) O 3.3 136 A4 Address bus of FLASH ROM O 3.3 137 A5 O 0 138 A6 O 3.3 139 A7 O 3.3 140 A8 O 0 141 A9 O 3.3 142 CVDD7 CORE CPU system (1.6V) power
- 1.6
supply 143 - - - ­144 DVSS9 GND - 0
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
7
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
10 PACKAGE AND IC BLOCK DIAGRAM
10.1. Main Block
PA051 : YESAP403
IC201 : C1BB00000543
IC271 : C1EA00000041
8
IC401 : YESAM284
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
IC681 : YESAM273
10.2. Display Block
IC902 : YESAM264
9
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
10.3. CD Servo Block
IC403 : YESAM171
IC402 : YESAM271
IC404 : YESAM178
IC405 : YESAM270
10
11 REPLACEMENT PARTS
LIST
Notes :
1. Be sure to make your orders of replacement parts according to this list.
2. Important safety notice: Components, identified by have special characteristics important for safety. When replacing any of these components, use only manufacturer´s specified parts.
3. Location keys in the remarks column indicates the general location of the parts shown in the exploded drawing, as in a road map.
4. The marking (RTL) indicates that Retention Time is limited for this item. After the discontinuation of assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available.
Order intake period is basically six months after the first
• •
shipment.
5. "A", "B" or ”C” marks in remarks column are indicated as follows :
A : CQ-C1321NE
• •
B : CQ-C1311NE
• •
B : CQ-C1301NE
• •
Ref. No. Part No. Part Name & Description Remarks [7210-02-11] MAIN BLOCK IC´s and TRANSISTORs
IC201 C1BB00000543 IC IC271 C1EA00000041 IC IC401 YESAM284 IC IC501 YESAM283 IC IC601 YESAM281 IC IC681 YESAM273 IC IC710 YESAM277 IC IC740 YESAM269 IC IC750 YESAM267 IC IC755 YESAM263 IC PA051 YESAP403 Tuner Pack Q052 YESAN082 Transistor Q054 B1GBCFNN0009 Transistor Q055 YESAN082 Transistor Q066 YESAN091 Transistor Q262 YESAN085 Transistor Q266 YESAN085 Transistor Q362 YESAN085 Transistor Q366 YESAN085 Transistor Q411 YEAN2SK536TB FET Q660 YESAN081 Transistor Q661 YESAN080 Transistor Q681 YESAN084 Transistor Q720 YESAN093 FET Q721 YESAN084 Transistor Q730 YESAN093 FET Q731 YESAN084 Transistor Q740 YESAN079 Transistor Q751 YESAN087 Transistor Q761 YESAN090 Transistor Q770 YESAN088 Transistor
DIODEs
D270 YESAD146 Diode
mark
CQ-C1321NE / CQ-C1311NE / CQ-C1301NE
Ref. No. Part No. Part Name & Description Remarks
D271 YESAD146 Diode D272 YESAD146 Diode D273 YESAD146 Diode D274 YESAD146 Diode D275 YESAD146 Diode D276 YESAD146 Diode D277 YESAD146 Diode D671 YESAD143 Diode D672 YESAD143 Diode D681 YESAD149 Diode D683 YESAD133 Zener Diode D684 YESAD133 Zener Diode D685 YESAD133 Zener Diode D689 YESAD133 Zener Diode D701 YESAD139 Diode D702 YESAD119 Zener Diode D710 YESAD144 Diode D720 YESAD146 Diode D740 YESAD146 Diode D741 YESAD118 Diode D750 YESAD141 Diode D760 YESAD146 Diode D761 YESAD140 Diode D770 YESAD123 Zener Diode D790 YESAD143 Diode
CAPACITORs
C051 YECUS1H470JC Ceramic, 47pF 50WV C053 YESCC234 Ceramic, 0.01µF 50WV C055 YESCC234 Ceramic, 0.01µF 50WV C059 F1J1H101A025 Ceramic, 100pF 50WV C061 YESCC327 Ceramic, 0.01µF 50WV C062 YESCC327 Ceramic, 0.01µF 50WV C065 YESCC233 Ceramic, 0.001µF 50WV C066 YESCC226 Ceramic, 470pF 50WV C067 YESCC234 Ceramic, 0.01µF 50WV C203 YESCC314 Electrolytic, 3.3µF 50WV C208 YESCC230 Ceramic, 0.33µF 16WV C210 YESCC228 Ceramic, 0.1µF 16WV C220 YESCC375 Electrolytic, 2.2µF 50WV C261 YESCC372 Electrolytic, 4.7µF 25WV C263 YECUS1C474KX Ceramic, 0.47µF 16WV C265 YESCC372 Electrolytic, 4.7µF 25WV C267 YECUS1C474KX Ceramic, 0.47µF 16WV C268 YECUS1C474KX Ceramic, 0.47µF 16WV C269 YECUS1C474KX Ceramic, 0.47µF 16WV C271 YESCC235 Ceramic, 0.0047µF 50WV C272 YESCC235 Ceramic, 0.0047µF 50WV C276 YESCC393 Electrolytic, 47uF 16WV C277 YESCC229 Ceramic, 1µF 16WV C278 YECUS1H104KX Ceramic, 0.1µF 50WV C279 YESCC368 Electrolytic, 2200µF 16WV C280 YESCC191 Ceramic, 2.2µF 50WV C281 YESCC191 Ceramic, 2.2µF 50WV C292 YESCC234 Ceramic, 0.01µF 50WV C303 YESCC314 Electrolytic, 3.3µF 50WV C308 YESCC230 Ceramic, 0.33µF 16WV C309 YESCC366 Electrolytic, 10µF 16WV C310 YESCC313 Electrolytic, 220µF 10WV C320 YESCC375 Electrolytic, 2.2µF 50WV C325 YECUS1H221JC Ceramic, 220pF 50WV C361 YESCC372 Electrolytic, 4.7µF 25WV C363 YECUS1C474KX Ceramic, 0.47µF 16WV C365 YESCC372 Electrolytic, 4.7µF 25WV C367 YECUS1C474KX Ceramic, 0.47µF 16WV C368 YECUS1C474KX Ceramic, 0.47µF 16WV C369 YECUS1C474KX Ceramic, 0.47µF 16WV C371 YESCC235 Ceramic, 0.0047µF 50WV C372 YESCC235 Ceramic, 0.0047µF 50WV C375 YESCC366 Electrolytic, 10µF 16WV C378 YECUS1H104KX Ceramic, 0.1µF 50WV C401 YESCC219 Ceramic, 10pF 50WV C402 YESCC245 Ceramic, 12pF 50WV
11
Loading...
+ 25 hidden pages