Panasonic BB-HCE481, BB-HCM381 User Manual
Installation Guide
Please read the Important Information before using.
Network Camera
Model No. BB-HCM381 (AC Adaptor Type)
Indoor Use Only
BB-HCE481 (PoE Type)
This manual is for both BB-HCM381 (AC Adaptor Type) and BB-HCE481 (PoE Type). Available features and operations
are different in part depending on the model. Read the Operating Instructions on the CD-ROM carefully and use the
Network Camera properly.
Mount the camera after the camera is connected and finished setting up following Getting Started.
Installation Procedures
•
"Network Camera" is called "Camera" in this manual.
•
"Setup CD-ROM" is called "CD-ROM" in this manual.
•
The illustrations used in this manual are of BB-HCM381.
•
Temporarily place
the camera.
Adjust the position and
direction of the camera.
Attach the camera.
The camera can be viewed in the least light requirement at 3 lx (default). Use supplemental lighting for the dimly lit places.
•
(The camera can be viewed in the least of 0.09 lx in the color night view mode (see page 86 of the Operating Instructions on
the CD-ROM), which may increase the refresh interval.)
After preparing the Ethernet cable that has enough length, mount the camera.
•
Mounting and cabling instructions described in this Installation Guide follow generally accepted guidelines suitable for residential
•
installations. In some areas, commercial and industrial installations are regulated by local or state ordinances. For such installations,
contact your local building department or building inspector for more details.
Mounting on the Ceiling
Make sure the camera is firmly mounted on the ceiling.
•
The camera is available between ±15˚ based on level line
•
for mounting.
The camera should be uninstalled from the ceiling when removing
•
the SD memory card (see page 146 of the Operating Instructions
on the CD-ROM).
The camera is intended for indoor use only. Prolonged exposure
•
to direct sunlight or halogen light may damage CCD.
The camera's MAC address and serial number are printed on the
•
bottom of the camera. They are needed in order for camera
configuration and maintenance. Record both of them for before
mounting the camera.
Set the Mounting type setting to [On the ceiling] on the Camera Setup
•
page (see page 86 of the Operating Instructions on the CD-ROM).
Two ways of wiring can be considered; wiring through a hole made
•
in the ceiling or wiring without making a hole for a cable in the ceiling.
Select either one of the two.
The audio cable or audio/video cable cannot be connected or
•
removed after mounting on the ceiling.
Temporarily place the camera where you like to view images.
Adjust the position and direction of the camera while you confirm that
images are displayed on the monitor as you imaged.
The camera can be mounted on the ceiling.
Attach the camera firmly when mounting on the ceiling.
Wiring through a hole made in the ceiling
Attach the Ceiling Plate B on the ceiling with Screws B.
1
Keep more than 100 mm
off the wall or other obstacles.
Camera direction
100 mm
Screws B (4 pcs.)
Attach the Ceiling Plate B more than 100 mm off the wall or other
•
obstacles from its center.
Make sure the camera is firmly mounted on a beam of wood etc.
•
When there is no beam, apply a board on the other side of the
ceiling to make sure the camera does not drop.
© 2006 Panasonic Communications Co., Ltd. All Rights Reserved.
PQQX15195ZA
KK0306JT0 (CE)
Make a hole for a cable.
2
65 mm
Attach the rubbers and dents on the camera to the Ceiling
3
Plate A and attach them firmly.
Hole for a cable
25 mm
Make a 25 mm hole
•
where is 65 mm away
from the center in the
plate.
Ceiling Mounting when the material of
the ceiling is mortar or concrete
Fit the Ceiling Plate B to the mounting position
1
and put marks.
Make holes at the marks and put plastic plugs
2
(customer-provided) into them.
Plastic plug
Fit the four rubbers
in place.
Fit the two dents in place.
Attach the Ceiling Plate A to the Ceiling Plate B and attach
4
them firmly with Screws A.
Four tabs
Fit the tabs to the holes and
1
move counterclockwise.
2
Attach firmly with Screws A.
Screws A (2 pcs.)
Install the camera so that the connecting part comes
•
to the front.
Connect all necessary cables (AC adaptor cord,
5
Ethernet cable, Audio Cable or Audio/Video Cable, etc.)
seeing Getting Started and attach the Ceiling Mounting Cover.
Adjust the " " of the main
1 2
unit to the " " of the Ceiling
Mounting Cover.
Move the Ceiling Mounting
Cover in the clockwise
direction until the " " of it fits
to the " " of the main unit.
Drill for concrete
(in case of tile,
use a drill for tile)
Note
When drilling into mortar, be careful of pieces of mortar
•
which may become loose and fall.
Mount the camera.
3
Mounting on the Table
Mount the camera at an even place on the table where
vibrations etc. are few.
Soft hammer
Be careful not to nip the cable etc.
•
When removing the Ceiling Mounting Cover, move it in the
•
counterclockwise direction. Adjust both " " and let down the
main unit.
Wiring without making a hole for a cable
in the ceiling
Follow the steps 1), 3), 4) and 5). Making a hole is not necessary.
Remove the tab of Ceiling Mounting Cover and wire
•
through the notch.
Set the Mounting type setting to [On the table] on the
•
Camera Setup page (see page 86 of the Operating
Instructions on the CD-ROM).
Loading...