Oster 2803, 2802 User Manual

User Manual

Electric Carving Knife

Manual de Instrucciones

Cuchillo de Trinchar Eléctrico

Manuel d’Instructions

Couteau à Découper Électrique

P.N. 115030

Visit us at www.oster.com

Cutting Board Not Included

For product questions contact:

Sunbeam Consumer Service

USA : 1.800.334.0759

Canada : 1.800.667.8623

www.oster.com

OSTER®is a registered trademark of Sunbeam Products, Inc.

In the U.S., distributed by Sunbeam Products, Inc., Boca Raton, FL 33431

In Canada, imported and distributed by Sunbeam Corporation, Limited.

Pour les questions de produit:

Sunbeam Consumer Service

États-Unis : 1.800.334.0759

Canada : 1.800.667.8623

www.oster.com

OSTER®est une marque déposée de Sunbeam Products, Inc.

Aux États-Unis, distribué par Sunbeam Products, Inc., Boca Raton, Florida 33431

Au Canada, importé et distribué par Sunbeam Corporation, Limited.

Para preguntas sobre los productos llama:

Sunbeam Consumer Service

EE.UU. : 1.800.334.0759 Canadá : 1.800.667.8623

www.oster.com

OSTER®es una marca registrada de Sunbeam Products, Inc.

En los EE. UU., distribuido por Sunbeam Products, Inc., Boca Raton, FL 33431

En Canadá, importado y distribuido por Sunbeam Corporation, Limited.

Printed in China Imprimé en Chine Impreso en China

MODELS/MODELOS

MODÈLES

2802, 2803

English-1

IMPORTANT SAFEGUARDS

When using your electric carving knife, basic safety precautions should always be followed, including the following:

EAD

LLINSTRUCTIONS

EFORE

SING

• Use the electric carving knife only for its intended use.

• To protect against risk of electrical shock, do not put power handle in water

or other liquid. DO NOT operate knife in water or under running water.

•

Children should not use this appliance. Care should be taken when using this appliance

near children.

• Unplug from outlet when not in use, before putting on or taking off parts and before cleaning. Disconnect power when changing blades.

•

DO NOT

touch moving parts.

•

DO NOT

operate any appl

iance with a damaged cord or plug, or after

the appliance

malfunctions, or is dropped or damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.

• DO NOT use with an extension cord.

• The use of attachments not recommended or sold by the manufacturer, may cause fire, electric shock or injury.

• DO NOT use outdoors or for commercial purposes.

• DO NOT let cord hang over edge of table or counter, or touch hot surfaces.

• BLADES ARE SHARP. Handle carefully. Always handle blades with hand away from cutting edge. Always store blades with cutting edge away from you.

• DO NOT use on frozen food or ice.

THIS UNIT FOR HOUSEHOLD USE ONLY

For 120V and 127V Versions Only

This appliance has a polarized alternating current plug (one plug is wider than the other). To reduce the risk of electric shock, as a safety feature, this plug

will fit in a polarized outlet only one way. If the plug does not insert fully in the outlet, reverse the plug. If it still fails to fit, contact a qualified electrician.

DO NOT ATTEMPT TO DEFEAT THIS SAFETY FEATURE.

SAVE THESE INSTRUCTIONS

The OSTER®Electric Carving Knife has been designed for carving roasts and other cuts of meat, slicing fruits and vegetables, slicing cakes and breads and cutting plain or fancy sandwiches.

OTE

This knife should not be used to cut bones, frozen foods in solid form or hard seeds, stones or pits in fruits.

English-2

SING THE ELECTRIC CARVING KNIFE

Be sure the electric cord is not connected to the outlet when inserting or removing the knife blades.

1. Pick up the knife blades by drip guards, holding the blades between the thumb and forefinger. Avoid touching the sharp, scalloped edges of the blades. (Figure A)

2. Insert the raised rivet on one blade into the key-hole slot on the other blade. This locks the ends of the blades. (Figure B)

TAINLESS

TEEL

LADES

ARVING

ORK

RIP

UARDS

ASY-TO

-G

RASP

ANDLE

OWER

ORD

LADERELEASE

ONTROLBUTTON

TORAGE

ASE

ON-O

WITCH

FIGURE A

FEATURES OF THE

OSTER

ELECTRIC

CARVING KNIFE

English-4English-3

Holding the blades with the drip guards between the thumb and forefinger, and with the scalloped edges of the blades facing away from the hand, slide the ends of the blades into the opening on the front of power handle. DO NOT PRESS THE BLADE RELEASE BUTTON WHEN INSERTING THE BLADES.

4. Push gently on each drip guard towards the electric carving knife until the blades “click” into place. Make sure the blades are firmly engaged. Cutting edges of the blades should be facing downward, away from the handle. (Figure C)

5. Plug the electrical cord into an electrical outlet. Use only voltage specified on bottom of the unit.

6. Press and hold the On-Off switch located on top of the handle to activate the knife and begin carving. (Figure D)

7. Guide the knife blades through the food to be sliced, pressing down lightly. A back and forth sawing motion is unnecessary. The movement of the blades slices the food for you.

8. When slicing is complete, release the On-Off switch to stop the blade action. Unplug the cord from the electrical outlet.

CLEANING YOUR ELECTRIC CARVING KNIFE

Unplug cord from the electrical outlet. Press the blade release button and gently remove both blades from the knife

using the drip guards. Slide the blades apart so the rivet on one blade is disengaged from the key-hole slot on the other blade.

Hold blades by the drip guards and wash in warm, sudsy water. Rinse blades and dry thoroughly. Be careful – blades are SHARP. The blades are dishwasher safe.

Wipe unit with a damp cloth.

DO NOT IMMERSE THE UNIT IN

WATER OR OTHER LIQUIDS.

TORAGE

Coil the electrical cord of the knife with a twist fastener. Store the knife in the storage case in a clean, dry location such as a cabinet or cupboard shelf. Slide plastic cover over blades and store blades in a drawer.

AINTENANCE

Do not attempt to sharpen the knife blades. Under normal use and care they will provide years of satisfactory use.

The motor of your electric slicing knife has been carefully lubricated at the factory using selected lubricants. It does not require any additional oil for the life of the unit.

Other than the recommended cleaning, no further user maintenance is necessary. Return

the electric slicing knife to your nearest authorized service

center for servicing or repairs.

TIPS FOR CARVING WITH THE ELECTRIC CARVING KNIFE

Use a carving board to avoid scratching china, metal platters or countertops.

Allow a roast to stand 15 to 20 minutes after roasting. Keep in a warm place. The meat will be easier to carve. Use a fork to hold meat when carving.

Remove all skewers from the meat before carving.

CARVING A STANDING RIB ROAST OF BEEF

Suggestions: Have your butcher remove the backbone of the roast and cut the rib bones short.

Arrange the roast on a cutting board with the largest end of the roast down and the rib side to your left. The small end of the roast is nearest the carver. Insert a carving fork between the two top ribs.

Slice across the roast from the fat edge of the rib bone. Free the slice from the bone using the special “trimming tip” of the knife.

CARVING A WHOLE HAM OR ROAST LEG OF LAMB

Place the leg of lamb or whole ham on the carving board with the shank end to the right of the carver. For a ham, turn the scored, fat-side up. For the leg of lamb, place the roast so that the meaty section faces away from the carver.

Insert a meat fork into the heavy part of the meat and cut several lengthwise slices from the less meaty side.

FIGURE B

FIGURE C

FIGURE D

English-5 English-6

Turn the ham or leg of lamb so that it rests upright on the cut surface. Cut a wedge from the shank end by starting at the base of the bulge and slicing down to the leg bone. Then, make another cut at an angle to this, close to the shank end. Lift out the wedge.

Starting at the shank end, cut thin, uniform slices down to the leg bone. To release the slices, run the electric carving knife under the slices, parallel to

the leg bone.

CARVING A ROAST TURKEY OR CHICKEN

Arrange the turkey or chicken on a carving board with the legs facing right. Starting at the side facing the carver, cut the leg from the body by grasping the leg with your left hand, pulling gently while cutting through the meat and the joint at the thigh.

Place the leg on the carving board and cut through the joint to sever the thigh bone from the drumstick. Slice the meat from the leg and thigh, carving parallel to the bone.

Insert the meat fork into the breast meat to secure the body. Sever the wing from the body by carving through the joint.

Start carving the breast just above the joint where the wing was removed. Cut thin slices of white meat, carving downward and cutting parallel to the breast bone.

SLICING A LOAF OF BREAD, AN ANGEL FOOD,

HIFFON OR SPONGE CAKE

To avoid crushing a fresh loaf of bread or sponge-type cakes, gently guide the electric carving knife through the bread or cake, cutting slices as thin as desired.

One-Year Limited Warranty

unbeam Products, Inc., or if in Canada, Sunbeam Corporation (Canada) Limited (collectively “Sunbeam”) warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. Sunbeam, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. Sunbeam dealers, service centers, or retail stores selling Sunbeam products do not have the right to alter, modify or any way change the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than Sunbeam or an authorized Sunbeam service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.

What Are the Limits on Sunbeam’s Liability?

Sunbeam shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition.

Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty.

Sunbeam disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.

Sunbeam shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.

Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.

How To Obtain Warranty Service

In the U.S.A. – If you have any question regarding this warranty or would like to obtain warranty service, please call 1.800.334.0759 and a convenient service center address will be provided to you.

In Canada – If you have any question regarding this warranty or would like to obtain warranty service, please call 1.800.667.8623 and a convenient service center address will be provided to you.

In the U.S.A., this warranty is offered by Sunbeam Products, Inc., located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited, located at 5975

Falbourne Street

, Mississauga, Ontario L5R 3V8.

PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF

THESE ADDRESSES OR TO THE PLACE OF PURCHASE.

+ 8 hidden pages