DVD EXPERT
Universal Remote Control
URC-4041
User’s Guide
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programming Device Control . . . . . . . . . . . . . . . . . . . . . . . . 9
Searching For Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Programming A Master Power Macro . . . . . . . . . . . . . . . . 12
Programming The Power Key For The Master Power Macro . . . 12
Operating The Master Power Macro . . . . . . . . . . . . . . . . . . . . 12
Clearing The Master Power Macro . . . . . . . . . . . . . . . . . . . . . 13
Using Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Restoring Keymoved Keys To Default Settings. . . . . . . . . . . . . 14
Restoring A Single Keymoved Key . . . . . . . . . . . . . . . . . . . . . . 14
Restoring All Keymoved Keys In A Single Mode . . . . . . . . . . . . . 14
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Programming Favorite Channel Scan . . . . . . . . . . . . . . . 16
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Locking Volume Control To One Mode
(Global Volume Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unlocking Volume Control For A Single Device
(Individual Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unlocking All Volume Control
(Restoring Default Setting ) . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For Audio Amplifiers. . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For Audio Receivers . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes For Cable Boxes. . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes For DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes For Home-Theater-In-A-Box Devices. . . . . . . . . . 22
Setup Codes For PVRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setup Codes For Satellite Receivers . . . . . . . . . . . . . . . . . . . . 22
Setup Codes For Satellite Receiver/PVR Combos . . . . . . . . . . 23
Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setup Codes For TV/DVD Player Combos. . . . . . . . . . . . . . . . . 27
Setup Codes For TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . 27
Setup Codes For VCRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setup Codes For VCR/DVD Player Combos . . . . . . . . . . . . . . . 30
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Limited Warranty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Additional Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2
INTRODUCTION
The One For All DVD Expert Universal Remote Control
(URC-4041) is designed to remotely operate up to four
home entertainment devices and features intuitive and
easy-to use buttons to operate a DVD component.Its
sophisticated technology will allow you to consolidate
your original home entertainment remote controls into
one easy-to-use product. Advanced features include:
• Intuitive buttons to allow easy access to functions
and menus on your DVD player and Home-TheaterIn-A-Box (HTIB) devices
• Direct code setup for easy device programming
• Step-and-Set code setup and Code Verification for an
alternate way to program devices
• Power macro for master on/off control of all of your
equipment with a single keystroke
• Volume Lock/Unlock feature to lock or unlock the
volume control to one mode or individual modes
• Device Key Re-Assignment to remotely control
a second (duplicate) device
• Favorite Channel Scan for easy channel surfing
• Color-coded keys to quickly locate popular functions
• Glow keys to aid operation when the ambient light
conditions are low
• Extensive code library for popular video and audio
devices including DVD players,PVR/DVRs,and
HTIB (Home-Theater-In-A-Box) devices.
The URC-4041 remote control requires two (2) new
AAA alkaline batteries (not included) and some easy
programming to control your devices.For best results,
please read and perform all instructions listed here.
Also,keep these instructions for future reference.
3
4
FEATURES AND FUNCTIONS
Use the illustration below to locate features on the
One For All DVD Expert Universal Remote Control
(URC-4041) and then study the Key Charts (on the next
two pages) to learn how they function.
To find out what type of devices can be controlled by
each device key after programming, see the Device
Ta b l e on page 7.
5
Key Charts
When the LED (red light) blinks,the
remote control is working and (after
programming) is sending signals.
Press
DVD/VCR, AUX, CBL/SAT,or TV
once to select a desired home
entertainment device to control.
Also see the Device Table on page 7.
Press
POWER once to turn on or off
the selected device.For master
power control, see Programming
A Master Power Macro on page 12.
Use the keypad (
1 ~ 9 and 0) to
directly select channels (e.g.,
009
or 031).
Use TV/VID to switch the TV’s input
to view TV or video programs.
Press
ENTER once after entering
the channel numbers on some TVs.
Use
GUIDE to display your selected
device’s program guide or setup
menu.
Press
MENU once to display your
selected device’s main menu.
Use
INFO/OSD to display the current
channel and program information
or on-screen directory.
Use
EXIT to exit from your selected
device’s guide or menu.
Use the
Cursor Keys to move the
cursor in the program guide and
menu screens.
Use
SELECT to choose options from
your selected device’s menu or guide.
Press
LAST once to recall the last
channel.For PVRs, use
LAST to
select live or recorded video.
Use
FAV to scan through all channels,
or after programming, to scan
through 10 favorite channels.
continued on next page...
6
FEATURES AND FUNCTIONS
Key Charts (continued)
Use CH▲ (or CH▼) to select the
next higher (or lower) channel.
Press MUTE once to turn the sound
off or on.
In the DVD mode, press
REPEAT
once to replay a selected chapter
(after pressing TITLE - see below).
Use
VOL▲ (or VOL▼) to raise (or
lower) the sound volume.
Use SLEEP to set the sleep timer on
a selected device if equipped with
this feature.
Use
ANGLE to perform the angle
function on your DVD player.
Use
AUDIO to select an alternate
audio channel (e.g., Spanish),if
available on your cable/satellite
service or DVD.
Press
TITLE once to display (or turn
off) a DVD’s title information (e.g.,
chapters,settings, etc.) if available.
In the DVD mode, press
ZOOM once
to zoom in on (or out of) a viewed
picture,if the function is available
on your DVD device.
Press
SUBTITLE/CC once to display
(or turn off) subtitles or closed
captions, if available on your DVD
or cable/satellite service.
Use
REW, PLAY,FWD, F.REW, PAUSE,
F.FWD,or STOP to control your VCR,
PVR, DVD player,or VOD (Video
On Demand) if available on
your cable/satellite service.
Press
REC twice to record a PVR or
VCR program.
Use
SET for all programming
sequences.
7
Device Table
NOTE: Please refer to the table below when performing the
instructions in “Programming Device Control” on page 9.
After programming,the One For All DVD Expert
Universal Remote Control will be able to control the
following types of devices:
DEVICE KEY CONTROLS THESE TYPES OF DEVICES
DVD Players, TV/DVD Player Combos,VCRs,
TV/VCR Combos,VCR/DVD Player Combos,
Home-Theater-In-A-Box devices,or
PVR/DVRs (Personal or Digital Video
Recorders)
Audio Amplifiers or Receivers; also use for
second VCR or DVD player (see page 14,
Re-Assigning Device Keys
).
Cable Boxes (Converters),Satellite Receivers,
or Satellite/PVR Combos
Tel e v i s i o ns
INSTALLING BATTERIES
1. On the remote control’s back, push the tab
and lift off the battery cover.
2. Obtain two (2) new AAA alkaline batteries.
Match the + and – marks on the batteries
to the + and – marks in the battery case,
then insert the new batteries.
3. Press the battery cover back into place.
The tab should click when the cover is
locked.
4. Test the remote control by pressing
any mode key (e.g.,
TV). If the batteries are
inserted correctly, the
LED (red light) will
blink once.
NOTE:When batteries need replacement,the remote control
will stop operating. Remove the old batteries and insert new
ones within 10 minutes to ensure all of your programming
information is restored.
8
❶
❸
❷
❷
PROGRAMMING DEVICE CONTROL
The One For All DVD Expert Universal Remote Control
is preprogrammed at the factory to operate an RCA TV,
a Toshiba DVD player, a Motorola cable box, and a
Pioneer audio receiver/amplifier. To control devices other
than the default brands, perform the following steps;
otherwise skip this section:
1. Turn on a desired device (e.g.,VCR or
DVD player) and, if applicable, insert
media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely
before proceeding.Highlight or write down the
codes and device you wish to program before
starting step 2.
2. On the remote control,press a device key
once (i.e.,
DVD/VCR,AUX, CBL/SAT,or TV).
NOTE: To program control of a DVD device,
VCR,PVR (or DVR),VCR/DVD Combo, or
Home-Theater-In-A-Box device, press
DVD/VCR once.
NOTE: To program control of an Audio
Amplifier or Receiver, press AUX once.
NOTE: To program control of a Cable Box,
Satellite Receiver, or a Satellite Receiver/PVR
(or DVR) Combo, press CBL/SAT once.
NOTE:To program control of a TV/VCR Combo,
press DVD/VCR once. After programming, you
will be able to control channel selection,volume,
and VCR functions.
NOTE: To program control of a TV/DVD Player
Combo, press DVD/VCR once. After programming, you will be able to control channel
selection, volume, and DVD functions.
3. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
4. Use the Manufacturer’s Codes (starting on
page 18) to locate the type of device and
brand name and then enter the first fourdigit code for your device. If performed
correctly,the
LED will blink twice.
NOTE: If the LED did not blink twice,repeat steps
2 through 4 and enter the same code again.
continued on next page...
9
PROGRAMMING DEVICE CONTROL
(continued)
5. Aim the remote control at the device and
press
POWER once. The device should turn
off. If it does not, repeat steps 2 through 5
(starting on the previous page),trying
each code for your brand until you find
one that works.If it still doesn’t work,try
Searching For Your Code below.
NOTE: If the device does not have a POWER
key, press the (Play) key.
6. Repeat steps 1 through 5 (starting on the
previous page) for each device you want to
control. For future reference, write down
each working device code in the following
boxes:
DVD/VCR Code:
Device Type:____________________
AUX Code:
Device Type:____________________
CBL/SAT Code:
Device Type:____________________
TV Code:
SEARCHING FOR YOUR CODE
If your device does not respond to the remote control
after trying all codes listed for your brand,or if your
brand is not listed at all,try searching for your code.
NOTE:Before performing a code search for a CD or DVD player
or a VCR, turn on the device and insert the required media.
For example,to search for a code for your TV:
1. On the remote control, press TV once.
2. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
3. Enter 9 - 9 - 1.The LED will blink twice.
10
4. Aim the remote control at the TV and
slowly alternate between pressing
POWER
and TV. Stop when the TV turns off (after
pressing
POWER).
NOTE: In the search mode,the remote control
will send IR codes from its library to the selected
device, starting with the most popular code first.
5. To lock in the code,press and release SET.
The
LED will blink twice.
6. To search for the codes of your other
devices, repeat steps 1 through 5,but
substitute the appropriate device key for
the device you are searching for.
CHECKING THE CODES
If you have set up the remote control using the
Searching For Your Code procedure (on the previous
page),you may need to find out which four-digit code
is operating your equipment.
For example,to find out which code is operating your TV:
1. On the remote control, press
TV once.
2. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
3. Enter 9 - 9 - 0.The LED will blink twice.
4. To view the code for the first digit, press
1
once.Wait 3 seconds,count the LED
blinks (e.g., three blinks = 3) and write
down the number in the leftmost box in
the TV code boxes on page 10.
NOTE: If a code digit is “0”, the LED will not
blink.
5. Repeat step 4 three more times for
remaining digits.Use
2 for the second
digit,
3 for the third digit,and 4 for the
fourth digit.Write down the code digits in
the remaining TV code boxes on page 10.
6. To check for codes of other devices,repeat
steps 1 through 5, but substitute the
appropriate device key for each device you
are checking. Write down the device’s code
digits in the appropriate code boxes on
page 10.
11
PROGRAMMING A MASTER POWER MACRO
In its default state,the POWER key on the One For All
DVD Expert Universal Remote Control will individually
power your home entertainment devices on or off.
However, you can also program a Master Power Macro
onto the
POWER key that will sequentially turn on or off
all the devices with a single key press.
Programming The Power Key For The Master
Power Macro
1. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
2. Enter 9 - 9 - 5.The LED will blink twice.
Then press
POWER once.
3. For the first device you want in the power-
on sequence,press its device key (e.g.,
CBL/SAT) once.
4. Repeat step 3 up to three more times to
add desired devices to the power-on
sequence.
5. To save the settings and exit the program,
press and hold
SET until the LED blinks
twice, then release
SET.
Operating The Master Power Macro
1. After programming,point the remote
control at the devices and press
POWER
for at least 2 seconds to sequentially turn
on or off your devices.
NOTE:When POWER is pressed for less than
2 seconds,a power command will only be sent
to the currently-selected device. This allows you
to still individually power devices on or off.
2. You will see the devices turn on or off
according to your programmed sequence.
NOTE:The currently-selected device will always
turn on or off first, followed by the remaining
programmed sequence.After the master power
sequence has been completed,the remote control
will be set to control the first powered-on device.
NOTE: If one or more devices does not have a
POWER key, the power off/on sequence may be
slightly delayed when the remote control signals
the device(s). This action is normal.
12
Clearing The Master Power Macro
1. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
2. Enter 9 - 9 - 5.The LED will blink twice.
Then press
POWER once.
3. Press and hold
SET until the LED blinks
twice, then release
SET.The Master Power
Macro is now cleared.
USING KEYMOVER
The One For All DVD Expert Universal Remote Control
includes a Key mover feature that allows you to map
(or copy) keys from one mode (i.e., source mode) to
another mode (i.e.,destination mode).
NOTE: The following keys should not be used as a source or
destination: DVD/VCR, AUX, CBL/SAT, TV, SET,FAV,and REC.
Programming Keymover
For example, if your DVD player does not have volume
control, you can map those keys (i.e.,
VOL▲, VOL▼,and
MUTE) from TV mode to DVD/VCR mode as follows:
1. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
2. Enter 9 - 9 - 4.The LED will blink twice.
3. For the source mode,press TV once.
4. For the source key, press VOL▲ once.
5. For the destination mode,press
DVD/VCR
once.
6. For the destination key, press VOL▲ once.
7. The
LED will blink twice, indicating the
keymoved sequence is correct.
8. Repeat steps 1 through 7 twice more to
map remaining volume control keys,
substituting
VOL▼ and MUTE as source and
destination keys in steps 4 and 6.
continued on next page...
13
USING KEYMOVER
Programming Keymover (continued)
Upon completion of the above procedure, you can now
use your One For All DVD Expert Universal Remote
Control to control the TV’s volume and mute in the
DVD mode,as well as in the TV mode.
Restoring Keymoved Keys to Default Settings
Restoring A Single Keymoved Key
1. Press a device key that has a keymoved key.
2. Press and hold
SET until the LED (red light)
blinks twice, then release
SET.
3. Enter 9 - 9 - 4.The LED will blink twice.
4. Press the destination key twice (where the
keymoved key is stored).The
LED will
blink twice.
Restoring All Keymoved Keys In A Single Mode
1. Press and hold
SET until the LED (red light)
blinks twice, then release
SET.
2. Enter 9 - 9 - 4.The LED will blink twice.
3. Press the destination mode twice (where
keymoved keys are stored).The
LED will
blink twice.
RE-ASSIGNING DEVICE KEYS
The One For All DVD Expert Universal Remote Control
can be set to control a second TV, PVR,VCR,DVD player,
or other device. For example, to control a TV, a cable box,
and two DVD players, re-assign the unused
AUX key to
operate the second DVD player as follows:
1. On the remote control, press and hold
SET
until the LED (red light) blinks twice, then
release
SET.
2. Enter 9 - 9 - 2.The LED will blink twice.
14
3. Press DVD/VCR once, then press AUX once.
The
LED will blink twice.
4. The AUX key is now ready to be set up to
control your second DVD player. See
Programming Device Control on page 9.
To re-assign other device keys to the
AUX key, repeat
steps 1 through 4 with a sequence from the below chart:
NOTE: Only one device can be assigned to an unused device
key at a time.
To Re-Assign Device Perform Sequence
AUX as 2nd TV key: SET - 9 - 9 - 2 - TV - AUX
AUX
as 2nd CBL/SAT key: SET - 9 - 9 - 2 - CBL/SAT - AUX
When a re-assignment is done,the LED will blink twice
to confirm your choice.At that time,you will need to
program the remote control for the new device (see
Programming Device Control on page 9).
USING CHANNEL SCAN
In the DVD/VCR, CBL/SAT,or TV mode, use the FAV key to
start a 3-second scan of all channels.If programmed,
use the
FAV key to scan only your favorite channels to
view a desired channel (see Programming Favorite
Channel Scan on next page.)
1. If Favorite Channel Scan has been set up,
skip to step 2.Otherwise, press
DVD/VCR,
CBL/SAT,or TV once.
2. Press
FAV once.
•IfFavorite Channel Scan has been set up,
scanning of favorite channels will start
and cycle through stored channels for
3 minutes or until stopped by pressing
any key.
•IfFavorite Channel Scan has not been
set up, scanning will start with the
current channel,then proceed to the
next channel up and cycle through all
channels for 3 minutes or until stopped
by pressing any key.
3. To stop scanning channels at any time,
press any key once.
15
PROGRAMMING FAVORITE CHANNEL SCAN
In the DVD/VCR, CBL/SAT,or TV mode, you can store a list
of up to 10 favorite channels, in any order, that will be
immediately scanned when
FAV is pressed (see Usi ng
Channel Scan on the previous page).
NOTE: Favorite channels can only be programmed for one
mode. After programming, if FAV is pressed while in another
mode, the remote control will start scanning all channels
instead (if applicable to the selected device).
1. On the remote control, press DVD/VCR,
CBL/SAT,or TV once.
2. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
3. Enter 9 - 9 - 6.The LED will blink twice.
4. Use the keypad to enter a favorite channel
number (e.g., 031).Then press SET once.
NOTE: If the original remote control required
pressing an Enter key to change the channel,
also press the ENTER key after the channel
number (e.g., 0 - 3 - 1 - ENTER).
5. If desired,repeat step 4 for each channel
to be stored, up to a total of 10 channels.
NOTE: If you try entering more than
10 channels,the remote control will
automatically exit programming.
6. To exit programming with less than
10 favorite channels stored, press and hold
SET until the LED blinks twice.Otherwise,
the remote control will automatically exit
the program after ten channels have been
stored.
16
CHANGING VOLUME LOCK
The One For All DVD Expert Universal Remote Control
is set at the factory for independent volume control of
each selected device.
However, you may change the Volume Lock setting to
Global Volume Lock so that a device’s volume will be
locked to one mode (e.g.,to control TV volume in all
other modes).After that, if desired, you can perform
Individual Volume Unlock on a selected device to set its
volume control for independent operation.
Locking Volume Control To One Mode
(Global Volume Lock)
1. Press and hold SET until the LED (red light)
blinks twice, then release
SET.
2. Enter 9 - 9 - 3 and then press any
mode key once (e.g.,
TV). The LED will
blink twice.
3. Now, when you press
VOL▲, VOL▼,or
MUTE, the volume of the selected device
(e.g.,
TV) will be controlled, regardless of
the mode you have selected.
Unlocking Volume Control For A Single Device
(Individual Volume Unlock)
1. After performing Global Volume Lock (on
page 16),press a desired mode key where
you want volume to be unlocked (e.g.,
AUX) and controlled within its own mode.
2. Press and and hold
SET until the LED (red
light) blinks twice,then release
SET.
3. Enter 9 - 9 - 3 and then press VOL▼ once.
The
LED will blink four times.
4. If desired,repeat steps 1 through 3
(of this section) for each device that you
want volume to be unlocked.
5. Now, after you select a device that has
volume unlocked (e.g.,
AUX), pressing
VOL▲, VOL▼,or MUTE will control the
device’s volume only in its own mode.
continued on next page...
17
CHANGING VOLUME LOCK (continued)
Unlocking All Volume Control (Restoring
Default Setting)
NOTE: Performing these instructions will restore independent
volume control for all programmed devices (e.g., TV volume
control in TV mode,VCR volume in DVD/VCR mode, etc.).
1. On the remote control, press and hold SET
until the LED (red light) blinks twice, then
release
SET.
2. Enter 9 - 9 - 3 and then press VOL▲ once.
The
LED will blink four times.
3. Volume will again be independently
controlled according to its default states
for all programmed devices.
MANUFACTURER’S CODES
Setup Codes For Audio Amplifiers
Aiwa 0406
Bose 0674
Carver 0269
Curtis Mathes 0300
Denon 0160
GE 0078
Harman/Kardon 0892
JVC 0331
Left Coast 0892
Linn 0269
Luxman 0165
Magnavox 0269
Marantz 0892, 0321,0269
NEC 0264
Nakamichi 0321
Optimus 0395, 0300
Panasonic 0308, 0521
Parasound 0246
Philips 0892, 0269
Pioneer 0013, 0300
Polk Audio 0892, 0269
RCA 0300
18
Realistic 0395
Sansui 0321
Shure 0264
Sony 0689, 0220
Soundesign 0078, 0211
Technics 0308, 0521
Victor 0331
Wards 0078, 0013, 0211
Yamaha 0354,0133
Setup Codes For Audio Receivers
Aiwa 0121, 0158,0189, 0405
Arcam 1120
Carver 0189
Denon 0004
Garrard 0463
Harman/Kardon 0110, 0189,1304
Integra 0135
JBL 0110
JVC 0074
Kenwood 0027, 0186
Linn 0189
MCS 0039
Magnavox 0189, 0391
Marantz 0039, 0189
Nakamichi 0097
Onkyo 0135
Optimus 0186, 0670
Panasonic 0039, 0309
Philips 0189, 0391, 1120
Polk Audio 0189
Quasar 0039
Sansui 0189
Sanyo 1251
Sharp 0186
Sony 0158
Soundesign 0670
Teac 0463
Technics 0039, 0309
Victor 0074
Wards 0158, 0189
Yamaha 0176, 0186
Zenith 0857
19
MANUFACTURER’S CODES (continued)
Setup Codes For Cable Boxes
ABC 0003, 0008, 0014, 0017
Americast 0899
Bell & Howell 0014
Bell South 0899
Director 0476
General Instrument 0476, 0003,0276, 0810
GoldStar 0144
Hamlin 0009,0273
Jerrold 0476, 0003,0276, 0012, 0014,0810
Memorex 0000
Motorola 0476,0276, 0810
Pace 0237
Panasonic 0000, 0107
Paragon 0000
Philips 0305, 0317
Pioneer 0877, 0144,0533, 1877
Pulsar 0000
Quasar 0000
Regal 0273, 0279
Runco 0000
Samsung 0144
Scientific Atlanta 0877,0008, 0017, 0477, 1877
Sony 1006
Starcom 0003
Supercable 0276
Tocom 0012
Torx 0003
Toshiba 0000
Zenith 0000, 0525, 0899
Setup Codes For DVD Players
Aiwa 0641
Apex Digital 0672, 0717,0755, 0794,0796, 0797, 0830, 0856,
1100
Blaupunkt 0717
Blue Parade 0571
Broksonic 0695, 0868
DVD2000 0521
Daewoo 0784
Denon 0490, 0634
Emerson 0591
Enterprise 0591
Fisher 0670
GE 0522, 0717, 0815
20
Go Video 0715, 0783
Gradiente 0651
Greenhill 0717
Harman/Kardon 0582, 0702
Hitachi 0573, 0664
Hiteker 0672
IRT 0783
Integra 0627
JBL 0702
JVC 0558, 0623
KLH 0717
Kenwood 0490, 0534, 0682,0737
Koss 0651
Lasonic 0798
Magnavox 0503, 0675
Malata 0782
Marantz 0539
Memorex 0831
Microsoft 0522
Mintek 0717, 0839
Mitsubishi 0521
Nesa 0717
Norcent 0872, 0895
Onkyo 0503, 0627
Oritron 0651
Panasonic 0490, 0632, 0703,0824, 1490
Philips 0503, 0539, 0646,0854
Pioneer 0525, 0571,0632, 0638
Polk Audio 0539
Proscan 0522
Qwestar 0651
RCA 0522, 0571, 0717, 0822
Raite 0665
Rotel 0623
Samsung 0573, 0820
Sansui 0695
Sanyo 0670, 0695
Sharp 0630
Shinsonic 0533, 0839
Sony 0533, 0864
Sylvania 0675, 0821
Technics 0490, 0703
Theta Digital 0571
Toshiba 0503, 0695
Tredex 0799
Urban Concepts 0503
XBox 0522
continued on next page...
21
MANUFACTURER’S CODES
Setup Codes For DVD Players (continued)
Yamaha 0490, 0539, 0545,0817
Yamakawa 0665
Zenith 0503, 0591, 0741
Setup Codes For
Home-Theater-In-A-Box Devices
Aiwa 1388, 1641
Alco 1390
Anam 1609
Apex Digital 1257
Audiovox 1390
Daewoo 1250
Fisher 1801
Integra 1298
JVC 1374
KLH 1390
Koss 1366
Marantz 1289
Norcent 1923
Onkyo 1298
Oritron 1366
Panasonic 1288, 1316, 1763,1764
Pioneer 1384
Polk Audio 1289
RCA 1390, 1609
Samsung 1295
Sony 1558, 1658, 1758
Venturer 1390
Setup Codes For PVRs
Panasonic 0616
Philips 0618
ReplayTV 0616
Sonic Blue 0616
Sony 0636
Tivo 0618, 0636
Setup Codes For Satellite Receivers
AlphaStar 0772
Chaparral 0216
Crossdigital 1109
DirecTV 0392, 0566,0639, 1142, 0247,0749, 0819, 1109,
1749
22
Dish Network System 1005, 0775,1775
DishPro 1005, 0775,1775
Echostar 1005, 0775,1775
Expressvu 0775, 1775
GE 0566
GOI 0775
General Instrument 0869
HTS 0775
Hitachi 0819
Hughes Network Systems 1142, 0749,1749, 1242
JVC 0775
Magnavox 0724, 0722
Memorex 0724
Mitsubishi 0749
Motorola 0869
Next Level 0869
Panasonic 0247, 0701
Paysat 0724
Philips 1142, 0749, 0724,1076, 0722, 1749,1242
Proscan 0392, 0566, 1392
RCA 0392, 0566, 0855, 0143,1392
RadioShack 0869
SKY 0856
Samsung 1109, 1276
Sony 0639, 1639
Star Choice 0869
Toshiba 0749, 0790, 1749
UltimateTV 0392, 0639, 1392
Uniden 0724, 0722
Zenith 0856, 1856
Setup Codes For Satellite Receiver/
PVR Combos
Echostar 1005, 1775,0775
Expressvu 1775, 0775
Hughes Network Systems 1242, 1142
Philips 1242, 1142
Proscan 1392, 0392
RCA 1392, 0392
Sony 0639, 1639
Setup Codes For TVs
AOC 0030
Admiral 0093, 0463
Aiko 0092
Aiwa 0701
continued on next page...
23
MANUFACTURER’S CODES
Setup Codes For TVs (continued)
Akai 0030
Alaron 0179
America Action 0180
Anam 0180
Apex Digital 0748, 0765,0767
Audiovox 0451, 0180, 0092,0623
Baysonic 0180
Bell & Howell 0154, 0016
Bradford 0180
Broksonic 0236, 0463
CXC 0180
Candle 0030, 0056
Carnivale 0030
Carver 0054
Celebrity 0000
Celera 0765
Changhong 0765
Cineral 0451, 0092
Citizen 0060, 0030,0056, 0092
Clarion 0180
Concerto 0056
Contec 0180
Craig 0180
Crosley 0054
Crown 0180
Curtis Mathes 0047,0054, 0154,0451, 0093,0060, 0030, 0145,
0056, 0016, 0166,1147, 1347
Daewoo 0451, 0092, 0623
Denon 0145
Dumont 0017
Electroband 0000
Emerson 0154, 0236,0463, 0180, 0178, 0179,0623
Envision 0030
Fisher 0154
Fujitsu 0179, 0683
Funai 0180, 0179, 0171
Futuretech 0180
GE 0047, 0051, 0451,0178, 0021, 1147,1347
Gibralter 0017, 0030
GoldStar 0030, 0178
Gradiente 0053, 0056
Grunpy 0180, 0179
Hallmark 0178
Harley Davidson 0179
Harman/Kardon 0054
24
Harvard 0180
Havermy 0093
Hitachi 0145, 0056, 0016, 1145
IRT 0628
Infinity 0054
Inteq 0017
JBL 0054
JCB 0000
JVC 0463, 0053
KEC 0180
KTV 0180, 0030
Kenwood 0030
Konka 0628, 0632, 0638,0703, 0707
LG 0056
LXI 0047, 0054, 0154, 0156,0178
Logik 0016
Luxman 0056
MGA 0150, 0030, 0178
MTC 0060, 0030, 0056
Magnavox 0054, 0030, 0179, 1254,1454
Majestic 0016
Marantz 0054, 0030
Matsushita 0250
Megatron 0178, 0145
Memorex 0154, 0250, 0463, 0150, 0178, 0179, 0016
Midland 0047, 0017,0051
Minutz 0021
Mitsubishi 0093, 0150,0178
Motorola 0093
Multitech 0180
NAD 0156, 0178, 0166,0866
NEC 0030, 0056
NTC 0092
Nikko 0030, 0178, 0092
Onwa 0180
Optimus 0154, 0250, 0166
Optonica 0093
Orion 0236, 0463, 0179
Panasonic 0250, 0051
Penney 0047, 0156, 0051, 0060,0030, 0178, 0021,1347
Philco 0054, 0463, 0030,0145
Philips 0054, 1454
Pilot 0030
Pioneer 0166, 0679, 0866
Portland 0092
Princeton 0717
Prism 0051
continued on next page...
25
MANUFACTURER’S CODES
Setup Codes For TVs (continued)
Proscan 0047
Proton 0178
Pulsar 0017
Quasar 0250, 0051
RCA 0047, 0090, 0679, 1047,1147, 1247, 1347,1447
RadioShack 0047, 0154, 0180,0030, 0178, 0056
Realistic 0154, 0180,0030, 0178, 0056
Runco 0017, 0030, 0603
SSS 0180
Sampo 0030
Samsung 0060, 0030, 0178, 0056
Sansei 0451
Sansui 0463
Sanyo 0154
Scotch 0178
Scott 0236, 0180, 0178,0179
Sears 0047, 0054, 0154,0156, 0178, 0179,0056, 0171
Semivox 0180
Semp 0156
Sharp 0093, 0688
Signature 0016
Sony 0000
Soundesign 0180, 0178, 0179
Squareview 0171
Starlite 0180
Supreme 0000
Sylvania 0054, 0030, 0171
Symphonic 0180, 0171
TMK 0178, 0056
TNCi 0017
TVS 0463
Tandy 0093
Technics 0250, 0051
Technol Ace 0179
Techwood 0051, 0056
Teknika 0054, 0180, 0150, 0060,0179, 0056, 0016,0092
Telefunken 0056
Toshiba 0154, 0156, 0060,1256, 1356
Vector Research 0030
Victor 0053
Vidikron 0054
Vidtech 0178
Wards 0054, 0030, 0178,0021, 0179, 0056,0016, 0866
Waycon 0156
26
White Westinghouse 0463, 0623
Yamaha 0030
Zenith 0017, 0463, 0178,0016, 0092
Setup Codes For TV/DVD Player Combos
Apex Digital 0830
Broksonic 0695, 0868
Panasonic 1490
Philips 0854
Sharp 0630
Sylvania 0821
Toshiba 0695
Setup Codes For TV/VCR Combos
Broksonic 1479
Citizen 1278
Daewoo 1278
Emerson 1278, 1479
Funai 0000
GE 1035, 0807, 1060
GoldStar 1237
Harley Davidson 0000
Hitachi 0000
Lloyd’s 0000
Magnasonic 1278
Magnavox 0000, 1781
Memorex 0037, 1162,1237
Mitsubishi 0807
Optimus 1162
Orion 1479
Panasonic 1035, 1162
Penney 1035
Quasar 1035, 1162
RCA 0807, 1035, 1060
Sansui 0000, 1479
Sears 0000, 1237
Sharp 0807
Sony 0000, 1232
Sylvania 1781
Symphonic 0000
Thomas 0000
Toshiba 0845
White Westinghouse 1278
Zenith 0000, 1479
27
MANUFACTURER’S CODES (continued)
Setup Codes For VCRs
Admiral 0048, 0209
Adventura 0000
Aiwa 0037, 0000
American High 0035
Asha 0240
Audiovox 0037
Beaumark 0240
Bell & Howell 0104
Broksonic 0184, 0121, 0209, 1479
Calix 0037
Canon 0035
Carver 0081
Citizen 0037, 1278
Craig 0037, 0047, 0240
Curtis Mathes 0060,0035, 0162,1035
Cybernex 0240
Daewoo 0045, 1278
Denon 0042
Dynatech 0000
Electrohome 0037
Electrophonic 0037
Emerex 0032
Emerson 0037, 0184,0000, 0121, 0043, 0209,1278, 1479
Fisher 0047, 0104
Fuji 0035
Funai 0000
GE 0060, 0035, 0240,0807, 1035, 1060
Garrard 0000
GoldStar 0037, 1237
Gradiente 0000
HI-Q 0047
Harley Davidson 0000
Harman/Kardon 0081
Hitachi 0000, 0042
Hughes Network Systems 0042
JVC 0067
KEC 0037
Kenwood 0067
Kodak 0035, 0037
LXI 0037
Lloyd’s 0000
MEI 0035
MGA 0240, 0043
MGN Technology 0240
MTC 0240, 0000
28
Magnasonic 1278
Magnavox 0035, 0039, 0081, 0000,1781
Magnin 0240
Marantz 0035, 0081
Marta 0037
Matsushita 0035, 0162
Memorex 0035, 0162, 0037, 0048, 0039,0047, 0240, 0000,
0104, 0209, 1162,1237
Minolta 0042
Mitsubishi 0067, 0043,0807
Motorola 0035, 0048
Multitech 0000
NEC 0104, 0067
Nikko 0037
Noblex 0240
Olympus 0035
Optimus 1062, 0162, 0037,0048, 0104, 1162
Orion 0184, 0209, 1479
Panasonic 1062, 0035, 0162,0225, 0616, 1035,1162
Penney 0035, 0037, 0240, 0042,1035, 1237
Pentax 0042
Philco 0035, 0209
Philips 0035, 0081, 0618
Pilot 0037
Pioneer 0067
Polk Audio 0081
Profitronic 0240
Proscan 0060, 1060
Pulsar 0039
Quasar 0035, 0162, 1035, 1162
RCA 0060, 0240, 0042, 0807,1035, 1060
RadioShack 0000
Radix 0037
Randex 0037
Realistic 0035, 0037,0048, 0047, 0000,0104
ReplayTV 0616
Runco 0039
STS 0042
Samsung 0240, 0045
Sanky 0048, 0039
Sansui 0000, 0067,0209, 1479
Sanyo 0047, 0240, 0104
Scott 0184, 0045, 0121,0043
Sears 0035, 0037, 0047,0000, 0042, 0104,1237
Semp 0045
Sharp 0048, 0807
Shogun 0240
Sonic Blue 0616
continued on next page...
29
MANUFACTURER’S CODES
Setup Codes For VCRs (continued)
Sony 0035, 0032, 0000, 0636,1232
Sylvania 0035, 0081, 0000,0043, 1781
Symphonic 0000
TMK 0240
Teac 0000
Technics 0035, 0162
Teknika 0035, 0037, 0000
Thomas 0000
Tivo 0618, 0636
Toshiba 0045, 0043, 0845
Totevision 0037, 0240
Unitech 0240
Vector 0045
Video Concepts 0045
Videomagic 0037
Videosonic 0240
Villain 0000
Wards 0060, 0035, 0048,0047, 0081, 0240,0000, 0042
White Westinghouse 0209, 1278
XR-1000 0035, 0000
Zenith 0039, 0000, 0209,1479
Setup Codes For VCR/DVD Player Combos
Go Video 0715
Samsung 0820
Sansui 0695
Sony 0864
Toshiba 0503
30
31
TROUBLESHOOTING
PROBLEM: LED (red light) does not blink when you
press a key.
SOLUTION: Replace batteries with two new AAA
alkaline batteries.
PROBLEM: LED blinks when you press a key, but
home entertainment device does not
respond.
SOLUTION: Make sure the remote control is aimed at
your home entertainment device and is
not farther than 15 feet away.
PROBLEM: The unit does not control home enter-
tainment devices or commands are not
working properly.
SOLUTION: Try all listed codes for the device brands
being set up.Make sure they can be
operated with an infrared remote control.
PROBLEM: Changing channels does not work
properly.
SOLUTION: If the original remote control required
pressing ENTER to change channels,
then press ENTER on the remote control
after entering the channel number.
PROBLEM: Tried Searching For Your Code method
and still could not find a working code.
SOLUTION: Clear the device key as follows: Press and
hold SET until the LED (red light) blinks
twice, then release. Next enter 9 - 9 - 2.
Then press the device key to be cleared
twice. Now repeat the Searching For Your
Code method on page 10.
PROBLEM: CH ▲ and CH▼ do not work for your
RCA TV.
SOLUTION: Due to RCA design (1983-1987),only the
original remote control will operate these
functions.
PROBLEM: No remote control of volume.
SOLUTION: See Changing Volume Lock on page 16 to
lock/unlock volume.
PROBLEM: If the above does not work.
SOLUTION: Please contact us in any of the
following ways:
• Please visit : www.oneforall.com
• If the above website is not able to
provide you with the information you
need, please email us at
ofasupport@ueic.com
• Customer Support : (330) 405-8612
32
INSTRUCTIONS TO THE USER
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules.These limits are designed to
provide a reasonable protection against harmful interference in a residential installation.This equipment
generates,uses, and can radiated radio frequency
energy and if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet or a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help
33
LIFETIME WARRANTY
One For ALL ("OFA") warrants this product to be free
from defects in materials and workmanship,under
normal use,throughout the period of the product’s
ownership by the original purchaser. This warranty
does not cover damage or failures caused by products
or services not supplied by OFA, or which result from
accident,misuses, abuse,neglect, mishandling,misapplication, faulty installation, set-up adjustment,
improper maintenance, alteration, maladjustment of
consumer controls, modifications, commercial use,or
that is attributable to acts of God.
There are no express warranties except as listed above.
OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF WARRANTY, ALL EXPRESS AND
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE,ARE LIMITED TO
THE WARRANTY PERIOD SET FORTH ABOVE.Some
states do not allow the exclusion or limitation of incidental or consequential damagers,or limitations on
how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
To obtain warranty service for a defective product,
please return the product,preferably in the original
carton,along with your purchase receipt,to the store of
original purchase for the first 90 days. A note detailing
the complaint would be helpful.The store,at its option,
will replace or repair this product if found to be defective.
If the unit has been purchased more than 90 days ago,
pls return it to Impact Distribution Services, 6262
Patterson Pass Road,Suite C, Livermore, CA 94550
together with the original receipt and $3.95 to cover
postage and handling. It will be repaired or replaced at
the manufacturer’s option. The manufacturer reserves
the right to substitute a currently manufactured model
with equal or superior features.
One For All: (330) 405-8655
URC-4041 April 2003
34
ADDITIONAL INFORMATION
As you update your home entertainment system, One
For All® has a universal remote control that will fit your
needs. Look for these exciting products at a retailer
near you.
One For All Access 3 . . . . . . . . . . . . . . . . . . . . . URC-3605
One For All Big Easy 3-Device . . . . . . . . . . . . . URC-3300
One For All DVD Expert 4-Device . . . . . . . . . URC-4041
One For All Big Easy 4-Device . . . . . . . . . . . . . URC-4330
One For All Access 4 . . . . . . . . . . . . . . . . . . . . . URC-4605
One For All Access 5 . . . . . . . . . . . . . . . . . . . . . URC-5705
One For All PVR 6-Device . . . . . . . . . . . . . . . . URC-6131
One For All 6-Device Home Theater. . . . . . . . URC-6011
One For All 8-Device Home Theater. . . . . . . . URC-8011
One For All 8L-Device Home Theater
With Learning. . . . . . . . . . . . . . . . . . . . . . . . . . URC-8811
One For All A/V LCD 8 Device
With Learning. . . . . . . . . . . . . . . . . . . . . . . . . . URC-8910
One For All IR/RF LCD 8 Device
With Learning. . . . . . . . . . . . . . . . . . . . . . . . . . URC-9910
One For All 8 Device Home Theater Remote
Powered By Kameleon . . . . . . . . . . . . . . . . . . . URC-9960
ONE FOR ALL® is the registered trademark of
Universal Electronics Inc.Computime International
Ltd. is the Licensee of the ONE FOR ALL® brand for
USA and Canada.
Copyright 2003 by Universal Electronics Inc. No part
of this publication may be reproduced,transmitted,
transcribed, stored in any retrieval system,or translated
to any language,in any form or by any means,electronic,
mechanical, magnetic,optical, manual,or otherwise,
without the prior written permission of Universal
Electronics Inc.
The One For All® DVD Expert Universal Remote
Control is compatible for use in North America,
excluding Mexico.
Loading...