Oliver 723 Service Manual

Walker, Michigan, U.S.A. 49534-7564

USER’S OPERATING AND INSTRUCTION MANUAL

MODEL 723

BUN SLICER

0702S20000-CVR

INDEX

DESCRIPTION/SPECIFICATIONS............................................................ 0723S20002

SAFETY INSTRUCTIONS.......................................................................... 0723S20003

ADJUSTMENTS......................................................................................... 0723S20004

OPERATING INSTRUCTIONS.................................................................. 0723S20005

MAINTENANCE/CLEANING/LUBRICATION............................................. 0723S20006

CHANGING THE BLADE........................................................................... 0723S20007

TROUBLE SHOOTING.............................................................................. 0723S20008

ASSEMBLY DRAWING MODEL 723 SLICER.…...................................... 0723S20009

WIRING DIAGRAMS ................................................................................. 0723S20010

WARRANTY............................................................................................... GEN 040225

RETURNED PARTS POLICY……............................................................. GEN 040226

SLICER WARRANTY PROCEDURE.......................................................... GEN 040227

0723S20001

SPECIFICATIONS

DESCRIPTION
These bun slicers have welded steel frames and stainless steel chutes. They are

compact, durable slicers for counter top use in slicing a variety of buns with speed and
economy.

SPECIFICATIONS

 Machine dimensions: Model 723

 Weight: Approximately 70 lbs.
 Standard Electrical Service:

1/3 HP, 1725 RPM, 1-60-115 Volts AC, 6 Amps.
PRODUCT CAPACITIES
 Maximum Product Size:
4-7/8 inches Wide and 3 inches High
 Blade Height (adjustable):
5/8 inch to 1-1/2 inches
 Maximum Cutting Depth:
4-3/8 inches

0723S20002

SAFETY INSTRUCTIONS

Every effort has been made by Oliver Products Company to provide you with a safe
machine. It is essential; however, that machine operators and maintenance personnel
observe the following safety precautions.

1. Before attempting to operate your slicer read this manual. Never allow an untrained
person to operate this machine.

2. Make sure that the machine is only connected to a properly grounded electrical
supply source of sufficient capacity for the load the slicer will put on it. Always
unplug the machine when it is not in use.

3. Always make sure the machine has been disconnected from the power supply before
cleaning or servicing.

4. Never stick your hand or any other objects into either end of the chute. Keep your
hands away from the moving parts of the machine.

5. Never attempt to adjust or service this machine until your are SURE

the blade has

stopped.

6. Always make sure the knife is not rubbing or hitting any metal components before re­starting the machine.

7. All guards must be in place before starting the machine.

8. Handle knife blades with care. Do not touch the moving knife.

9. Use only proper replacement parts.

10. In addition to these general safety instructions, also follow the more specific safety
instructions given for the different areas of the machine in the operating instructions.

0723S20003

ADJUSTMENTS

WARNING

NEVER ATTEMPT TO ADJUST OR SERVICE THIS MACHINE UNTIL
YOU ARE SURE THE BLADE HAS STOPPED.

OUTSIDE SIDE GUIDE
This guide is used to determine the amount of "Hinge" left on the product and can be

adjusted from leaving approximately a 1/2" hinge to a complete sever.
The guide is adjusted by loosening the two knobs which are below and to the outside of

the table and by sliding the guide in or out to generate the desired amount of hinge. Re­tighten the knobs when the guide is in the desired location.

CAUTION

MAKE SURE THAT THE BLADE IS NOT HITTING ANY OF THE OTHER
COMPONENTS BEFORE RE-STARTING THE MACHINE.

TABLE HEIGHT ADJUSTMENT
The table can be adjusted so that the height of the blade above the table is between 5/8"

and 1-1/2".
To change the height of the blade, loosen the handle located on the left side of the unit.

Once loosened, simply push or pull the handle until you’ve reached the desired height
associated on the slice height gauge. The slice height gauge is located on the front of
the unit. Once the desired slice thickness is achieved re-tighten the handle on the left
side of the base to secure the table in the new position.

CAUTION

MAKE SURE THAT THE BLADE IS NOT HITTING ANY OF THE OTHER
COMPONENTS BEFORE RE-STARTING THE MACHINE.

INSIDE SIDE GUIDE
Generally it is best to leave the inside guide adjusted to the maximum opening, this will

allow the product to pass through uninhibited for maximum slicing speed. However,
some products will require its use to reduce jamming.

(continued on next page)

0723S20004