NuTone NGD00Z Installation Instructions Manual
➌
PRODUCT COMPONENTS
➍
TILT SENSOR INSTALLATION AND BATTERY
➎
PAIRING (INCLUDING) WITH THE SYSTEM
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,NGD00Z - P/N: 10006014 X5 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly.
NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors
only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
Do not install the Remote Command Transceiver on
garage door operators manufactured prior to 1993
(models without an operational safety beam entrapment
detection system).
WARNING
The Remote Command Transceiver must be mounted in
the garage, in sight of the garage door, where the visual
and audible movement warning indicators can be clearly
seen and heard.
NGD00Z
POWER
INPUT
JACK
WARNING
LIGHT
LINK
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
POWER
SUPPLY
TILT
SENSOR
STATUS
INDICATOR
OPTIONAL
ADJUSTABLE
MOUNTING
BRACKET
POWER
SUPPLY
RETAINING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
WIRE
TIES
TO INCLUDE THE NGD00Z
INTO YOUR CONTROLLER
1
2
WALL
OUTLET
POWER
SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
NGD00Z
Press and release the link button
on the NGD00Z.
Note: Plug in the NGD00Z
near your Z-Wave Controller
for these steps
Place your Z-Wave Controller into
Discovery or Include mode.
TO EXCLUDE THE NGD00Z
FROM YOUR CONTROLLER
Confirm that the NGD00Z was
recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on including devices.
3
1
2
Press and release the link button
on the NGD00Z.
Place your Z-Wave Controller into
Exclude mode.
Confirm that the NGD00Z was
excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on excluding devices.
3
CR2032
PLUS SIDE UP !!!
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
Insert the
battery
into the
transmitter
To open the case, twist
a small screwdriver
in case slot
SLOT
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
POST ON
BOTTOM
"UP"
ARROWS
Snap the sensor onto
the mounting plate
To activate the tilt sensor,
remove the battery protection pull strip
2
ARROWS ON PLATE
& SENSOR POINT UP
LOW BATTERY REPLACEMENT
1
2
1
3
Attach the mounting plate
to the top panel of the door
NGD00Z Overview
• A garage door opener remote
command transceiver with built-in
Z-Wave technology.
• Allows remote operation of a garage
door opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve
communications within the Z-Wave
mesh network.
NGD00Z Summary of Operation
• NGD00Z connects to the garage door
opener’s pushbutton wall console
terminals.
• A wireless tilt sensor mounts on the
garage door and reports the door’s
position to the NGD00Z.
• NGD00Z responds to Z-Wave
commands from Z-Wave controllers to
open or close the garage door.
• A warning indicator light flashes and
a beeper sounds for 5 seconds before
the door begins to move.
• If the door does not completely
open or close, a second open or
close command can be sent after
30 seconds.
• If the door does not completely open
or close after the second attempt,
the NGD00Z operation is suspended
until a local garage door pushbutton is
activated.
Z-Wave Information
• Z-Wave® is a registered trademark
of Sigma Designs Inc. and/or its
subsidiaries.
• Z-Wave is an Interoperable two-way RF
mesh networking technology designed
for use with a Z-Wave gateway/
controller and other Z-Wave enabled
devices.
• Replication is the process of copying or
transferring your Z-Wave network from
one controller to another.
• This is a Security enabled Z-Wave
product and must be used with a
Security enabled Z-Wave controller
in order to fully utilize this product. As
such, this device will not respond to
Basic CC commands.
• ASSOCIATION: The NGD00Z supports
1 Group with 1 Node. Group 1 must be
assigned the Node ID of the controller
to which unsolicited notifications from
the NGD00Z will be sent. The Z-Wave
controller should set this association
automatically after inclusion.
NGD00Z
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Installation Instructions
➊
PRODUCT DESCRIPTION
➋
SAFETY NOTES
➏
NGD00Z MOUNTING
➐
NGD00Z CONNECTIONS
➑
SYSTEM OPERATION
➒
OPERATION NOTES
1. The warning light will flash and the warning beeper will sound for five seconds
before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the NGD00Z
will allow user to try to operate the door one more time. If the second attempt fails,
the NGD00Z will go into lock-out mode. See Note #3.
3. If the NGD00Z is in lock-out mode and will not accept remote commands, activate
the door from the pushbutton wall console.
4. Once the NGD00Z has initiated the movement of the garage door, another
command cannot be sent for 30 seconds. This eliminates the chance of “bouncing”
the garage door and possibly damaging the garage door opener.
➓
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Unable to include in
Z-Wave network.
NGD00Z was not
properly excluded
from a previous
Z-Wave network.
1. Reset the NGD00Z by pressing
the LINK button 5 times. A quick
beep followed by a longer beep
will indicate the reset.
The NGD00Z does
not flash or beep
when activated.
No power to the
NGD00Z.
1. Make sure the power supply is
plugged in securely to a live outlet.
2. Make sure the power cord
is plugged in securely to the
NGD00Z.
The NGD00Z
flashes and beeps
when activated but
the door does not
move.
Obstruction
blocking the door
or incorrect wiring.
1. Make sure that there are no obstacles
preventing the door from moving.
2. Make sure that the NGD00Z
connection wires are connected
to the proper terminals on the
garage door opener. Trace the
wires from the garage door
opener’s pushbutton wall console
to the door opener. This is where
the NGD00Z connection wires
should be connected.
Garage door opens
or closes, but the
status does not
change on the
Z-Wave Controller.
The tilt sensor
signal is not being
received by the
NGD00Z.
1. Make sure the tilt sensor is
mounted correctly on the garage
door, with the arrow pointing up.
2. Make sure the battery pull tab has
been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
REGULATORY NOTICES
This device complies with part 15 of the FCC Rules and Industry Canada license exempt RSS
standard(s). Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Les changements ou modifications non approuvés expressément par la partie responsable de la
conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement.
This equipment has been tested and found to comply with the limits for Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,NGD00Z - P/N: 10006014 X5 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
The NGD00Z typically
mounts on the ceiling
near the opener and
the power outlet
Tilt sensor
mounted on
the top panel
of the door
THE NGD00Z CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE NGD00Z WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
3/16" HOLES
FOR ANCHORS
The optional adjustable
mounting bracket fits
3 ways on the NGD00Z
The bracket snaps onto
indents on either side or
on the end of the NGD00Z
Secure
bracket
with screw
Use the four screws
and anchors to mount
the NGD00Z above
the opener
INDENT
INDENT
Use the bolts and nuts supplied
to attach the bracket to a secure
structure
BE SURE THE NGD00Z
IS CLEAR OF ALL MOVING
PARTS OF THE GARAGE DOOR
AND THE WARNING LAMP IS
NOT OBSTRUCTED
INDENT
1A
2A
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
! WARNING !
1
PUSHBUTTON
PUSHBUTTON
GARAGE
DOOR
OPENER
Connect the NGD00Z connection
wires to the pushbutton wall console
terminals on the garage door opener.
The terminals may be named "PWC", "WC",
"PB", "PUSHBUTTON", or "RED and WHITE".
Terminal names and locations vary by model.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
Remove the screw from 120 VAC
outlet faceplate. Secure the retaining
bracket to the faceplate with the provided
screw. Snap the power supply into the
bracket while plugging into the outlet.
USE WIRE TIES TO SECURE
EXCESS WIRING CLEAR
OF ALL MOVING PARTS
OF THE GARAGE
DOOR AND OPENER
Either wire can
connect to either
terminal
Plug the power cord
into the power input
jack on the NGD00Z
2
1
3
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
Use your Z-Wave Controller to
activate your garage door opener
The NGD00Z will activate
the door opener and open
or close the door
STAY CLEAR
OF THE DOOR !!!
3
The NGD00Z will beep and
flash for five seconds before
the door moves
4
5
Restore power to your
garage door opener
1
To synchronize the system,
use the garage door opener's
pushbutton to manually open
and close the door
2
STAY CLEAR
OF THE DOOR !!!
Copyright © 2015 Broan-NuTone LLC 99045345A
NGD00Z Specifications
Power Supply: Input: 120 VAC, 0.8 A
Output: 12 VDC, 2 A
Operating Temperature: -4º—122° F (-20º—50° C)
Audible Alarm: 45 db @ 10 feet
Strobe: 360 Lumens
Communications: Z-Wave (908.4 MHz)
Mounting: Screws and anchors to
the ceiling, or bracket to the
opener’s hanging hardware
Tilt Sensor Specifications
Power Supply: Type CR2032 Coin Cell Battery
Operating Temperature: -4º—122° F (-20º—50° C)
Batter y Life: 24 Months (typical)
Communications: Proprietary 345 MHz
Range: 100 feet line-of-sight to NGD00Z
Mounting to Garage Door: Double-sided tape or two
mounting screws
(Specifications subject to change without notice)
NOTICE TO USERS IN CALIFORNIA - CR COIN
CELL LITHIUM BATTERY INFORMATION: THIS
PRODUCT CONTAINS A CR COIN CELL LITHIUM
BATTERY WHICH CONTAINS PERCHLORATE
MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.
Loading...