Nokia 3300, NEM-1 Service Manual

Page 1
CCS Technical Documentation
NEM-2 Series Transceivers

LGA Rework Instructions

Issue 1 07/03 Nokia Corporation
Page 2
NEM-2
LGA Rework Instructions CCS Technical Documentation
[This page left intentionally blank]
Page 2 Nokia Corporation Issue 1 07/03
Page 3
NEM-2
Table of contents
LGA/BGA Rework ........................................................................................................ 4
Rework instruction for NEM-2 (R1011)........................................................................ 4
Rework technology ......................................................................................................4
Ministencils and Jigs for NEM-2 .................................................................................6
Used rework programs for NEM-2 ..............................................................................7
Issue 1 07/03 Nokia Corporation Page 3
Page 4
NEM-2
LGA Rework Instructions CCS Technical Documentation

LGA/BGA Rework

Rework instruction for NEM-2 (R1011)

Rework technology

How to use the ministencil:
The faulty component is removed in the rework station
The old solder on the pads is removed with the solderwick
The new component is installed in the jig
The stencil and the component are installed in the jig . The alignment is done with jig’s centering pins.
Add paste (the same type as used in the product) on the stencil near the openings. Use sufficient amount of paste.
Print over the stencil with squeegee twice (the squeegee can be the same type as MPM’s squeegee). Printing is done manually.
The stencil rises from the jig and the component rises with the stencil.
Now the component can be moved carefully on the vacuum nozzle of the rework station with the tweezers.
The component is aligned with the prism to the right position of PWB pads and is set on the near PWB’s surface. The component is soldered in the rework station like CSP components.
The rework station’s component specific vacuum nozzle size and pro­gram are defined in the table.
Page 4 Nokia Corporation Issue 1 07/03
Page 5
NEM-2
Figure 1: Side 1 (top) PWB name:EW21_XX
Figure 2: Side 2 (Bottom) PWB name:EW21_XX
Issue 1 07/03 Nokia Corporation Page 5
Page 6
NEM-2
LGA Rework Instructions CCS Technical Documentation

Ministencils and Jigs for NEM-2

Table 1:
PART PARTCODE
Z802 FM Radio SK-5 (0274507) RJ-24 (0770688) ST-5 (0770691)
N356 Power Amplifier SK-6 (0274508) RJ-25 (0770689) ST-6 (0770692)
SERVICE KIT
REWORK JIG
REWORK STENCIL
Page 6 Nokia Corporation Issue 1 07/03
Page 7
NEM-2

Used rework programs for NEM-2

PART NOZZLE PROGRAM AIRFLOW
N700 15x15 VAN_PA.bpf 15L/MIN
Z802 10x10 8x8.bpf 15L/MIN
N356 8x8 8x8..bpf 15L/MIN
N500 10x10 8x8..bpf 15L/MIN
D200 12x12 12x12.bpf 15L/MIN
D400 12x12 12x12..bpf 15L/MIN
D450 12x12 12x12..bpf 15L/MIN
D851 12x12 12x12..bpf 15L/MIN
D900 8x8 8x8.bpf 15L/MIN
B200 6x6 Z301.bpf 15L/MIN
Issue 1 07/03 Nokia Corporation Page 7
Page 8
NEM-2
LGA Rework Instructions CCS Technical Documentation
Figure 3: Jig-drawing of FM Radio
Figure 4: Jig-drawing of Power Amplifier
Page 8 Nokia Corporation Issue 1 07/03
Page 9
NEM-2
Figure 5: Stencil Gerber file data of Comp Code
Issue 1 07/03 Nokia Corporation Page 9
Page 10
NEM-2
LGA Rework Instructions CCS Technical Documentation
Page 10 Nokia Corporation Issue 1 07/03
Loading...