Netgear GS105PE-10000S Quick Start Guide

Installation Guide

ProSAFE Plus 5-Port Gigabit PoE Pass Through
Switch GS105PE

Step 2. Connect power.

Step 3. Check status.

PoE pass through
enabled

Off

Power LED

Step 1. Connect equipment.

GS105PE switch

Computer Server

PoE Switch

PoE pass through
disabled

1000 Mbps activity
(blinking)

No link (off)

1000 Mbps link

Port LEDs Left

10/100 Mbps link

10/100 Mbps activity
(blinking)

PoE PD (Port 5)
LED Right

PoE PSE (Ports 1
and 2) LEDs Right

Receiving power
from PSE per 802.3at
specification

Receiving power
from PSE

Off

Supplying power

PoE Fault

No PoE Power
PD not deteced

GS105PE switch

PoE Switch

PoE PD Port PoE PSE Port

November 2013

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered
trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other
countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.

NETGEAR, Inc.

350 East Plumeria Drive
San Jose, CA 95134 USA

Set Up the Switch Configuration Utility

Plus switches are plug and play. You can install a configuration utility to select
additional options to manage and customize the switch for your network. This utility
is on the resource CD that was shipped with the switch.

Note: The configuration utility is installed on your computer and is supported only

on Windows computers.

To install the configuration utility:

1. Insert the resource CD into a computer that is connected to the switch.

2. Click Install ProSAFE Plus Utility and follow the prompts to install the

program.

The switch configuration utility is installed in the program directory of your
computer and a ProSAFE Plus Utility icon is placed on your desktop.

To configure the switch:

1. Double-click the ProSAFE Plus Utility icon.

The configuration home screen displays a list of plus switches that it discovers
on the local network.

2. Select the switch that you want to configure.

You are asked to enter the password for the switch.

3. Enter the switch’s password in the password field.

The switch’s default password is password.

4. Use the utility to configure the switch.

For a description of plus features, see the ProSAFE Plus Switch Utility User
Guide. You can access the user guide through links on the Help tab of the utility

or on the resource CD.

PoE Pass Through

This switch supports PoE pass through. When the power LED is blinking green, it

means PoE pass-through is disabled because the input voltage to port 5 is less
than 45 VDC. When a PoE switch is connected to the PD port, power is passed
through the switch to the PSE ports. PSE port 1 is always given priority. Power
not consumed by the switch or a device connected to port 1 is supplied to port 2.

The following table describes the behaviour of the PSE ports.

Specifications

Port 5 Connected
Device Type

Scenario Port 1 PD Class

Type Support

Port 2 PD Class
Type Support

IEEE802.3af PoE
Switch or Injector

Device connected to
port 1

Class 1 or 2 NA

IEEE802.3af PoE
Switch or Injector

Device connected to
port 2

NA Class 1 or 2

IEEE802.3at PoE
Switch or Injector

Device connected to
port 1

Class 0 or 3 NA

IEEE802.3at PoE
Switch or Injector

Device connected to
port 2

NA Class 0 or 3

IEEE802.3at PoE
Switch or Injector

Device connected to
port 1 and port 2

Class 1 or 2 Class 1 or 2

Specification Description

Network interface RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T

Network cable Category 5e (Cat 5e) or better Ethernet cable

Ports 5

Power 37-57 VDC, 600mA max@42.5V

Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and
use it to register your product at https://my.netgear.com.

You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit http://support.netgear.com.

NETGEAR recommends that you use only the official NETGEAR support resources.

For the current EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

Power consumption 21.95W maximum

Weight 0.47 Kg (1.04 lbs)

Dimensions
(W x D x H)

158 mm x 100 mm x 27 mm
(6.22 in. x 3.93 in. x 1.06 in.)

Operating
temperature

0–50° C (32–122° F)

Operating humidity 10%–90% relative humidity, noncondensing

Electromagnetic
compliance

CE Class B, FCC part 15 Class B, VCCI Class B,
C-Tick Class B, CAN ICES-3 (B)/NMB-3(B)

Safety agency
approvals

CE mark

Specification Description (Continued)