NETGEAR GS105NA User Manual
GS105v4 5-Port
Gigabit Ethernet Switch
modem
firewall
broadband
Power
100 Mbps
10 Mbps LED
Both LEDs light for
a 1000 Mbps connection.
GS105v4_IG 2Mar10.fm Page 1 Wednesday, March 2, 2011 12:32 PM
Installation Guide
ProSafe 5-Port Gigabit Ethernet Switch GS105v4
Estimated installation time: 5-10 minutes
Package Contents
The package includes:
• ProSafe 5-Port Gigabit Ethernet Switch GS105v4
• AC power adapter
• GS105v4 Installation Guide (this document)
• Warranty/Support information card
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface such as a
table, desk or shelf. You can use wall-mounting screws (not provided) to hang the
switch in an open space on a wall.
Make sure the selected location is:
• Not in direct sunlight or near a heater or heating vent.
• Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear
space on all sides of the switch.
• Well ventilated (especially if it is in a closet).
Depending on the speed of your network devices, you need a Category 3 (10
Mbps), Category 5 (100 Mbps) or Category 5e (1000 Mbps) Ethernet cable with RJ45 connectors for each device you want to connect to the switch. Each Ethernet
cable must be less than 328 feet (100 meters).
Install the Switch and Connect the Other Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device
and insert the other end into one of the Ethernet ports on the switch.
3. Connect the power adapter cord into the back of the switch and then plug the
adapter into a power source (such as a wall socket or power strip).
4. Check the LEDs to verify that the equipment is connected correctly.
• The Power LED is lit.
• Each RJ-45 jack has 2 LEDs. For each jack that is connected to a powered
device, the Link LED is lit, and it flashes when activity occurs. If the
connection is 10 Mbps or 100 Mbps, one LED lights up. If the connection is
1000 Mbps, both LEDs light up.
Note: If any light does not operate as indicated, go to the Troubleshooting section.
Troubleshooting
The Power light is not lit.
The switch has no power.
• Make sure that the power cord is correctly connected to the switch.
• Make sure that the power adapter is connected to a functioning power outlet. If it
is in a power strip, make sure that the power strip is turned on. If the socket is
controlled by a light switch, make sure that the switch is in the on position.
• Make sure you that are using the NETGEAR power adapter supplied with your
switch.
The Port number light is not lit for a connected device or stays on continuously.
There is a hardware connection problem.
• Make sure that the cable connectors are securely plugged in at the switch and
the device.
• Make sure that the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure
that the card or adapter is installed correctly and is working.
• Make sure that the cable is less than 328 feet (100 meters).
GS105v4_IG 2Mar10.fm Page 2 Wednesday, March 2, 2011 12:32 PM
Technical Specifications
Standards compatibility ISO/IEG 802.3i (ANSI/IEEE 802.3i) 10BASE-T, IEEE 802.3i
10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab
1000BASE-T, IEEE 802.3x Flow Control; Jumbo frame 9720,
IEEE 802.1p priority; DSCP priority; Compatible with
Windows, Mac OS, NetWare, Linux.
Network interface RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-
T Ethernet interface
Power 12W max and 12V@1A DC input
Power consumption 4W max
Physical dimensions W: 94 mm (3.7") D: 104 mm (4.1") H: 28 mm (1.1")
Weight 300 g (0.66 lbs)
Operating temperature 0 to 50° C (32 to 122° F)
Operating humidity 10% to 90% relative humidity, noncondensing
Electromagnetic
compliance
Safety agency approvals
for the power adapter
FCC Part 15, Class B; EN 55022 (CISPR 22), VCCI Class B
CE mark, C-Tick
Technical Specifications
Address database size 4K MAC addresses
Queue buffer 128 KB Embedded
.
Statement of Conditions
In the interest of improving internal design, operational function, and/operability,
NETGEAR reserves the right to make changes to the product described in this
document without notice. NETGEAR does not assume any liability that may occur
due to the use or application of the product(s) or circuit layout(s) described herein.
Technical Support
Thank you for selecting NETGEAR products.
After completing the installation, locate the serial number on the bottom label of your
product, and use it to register your product at:
http://www.NETGEAR.com/register.
Registration on the website or over the phone is required before you can use our
telephone support service. The phone numbers for worldwide regional customer
support centers are on the Warranty and Support Information card that came with
your product.
For complete DoC please visit the NETGEAR EU Declarations of Conformity
website at: http://kb.netgear.com/app/answers/detail/a_id/11621/
Go to http://kbserver.netgear.com for product updates and Web support.
Performance Specifications
Frame filter rate 14,880 frames/sec max for 10M port; 148,800 frames/sec
max for 100M port; 1,488,000 frames/sec for 1000M port
Frame forward rate 14,880 frames/sec max for 10M port; 148,800 frames/sec
max for 100M port; 1,488,000 frames/sec max for 1000M port
Network latency (using
64-byte packets)
10Mbs: 26µs max
100Mbs: 4.6µs max
1000Mbs: 2.74µs max
March 2011
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,
this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
©2011 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks of
NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
Loading...