NETGEAR AGM721F User Manual
NETGEAR
Everybody's connecting.
___________
GBIC Module AGM721T / AGM721F
The Gigabit interface Converter (GBIC) slots on NETGEAR's managed switches
provides you with a highly adaptable network. You have the option of building
your network for copper and/or fiber gigabit uplinks.
Installing a GBIC module:
1. Insert the module into the slot, pressing firmly to seat the module.
2. Using either the browser GUI or the Console interface, go to the Set up menu
and select GBIC.
3. Select GBIC for the port and save the new setting (hit Apply or Ctrl-W).
Trademarks
NETGEAR is a registered trademark of NETGEAR, Inc.,
in the United States and other countries. All other
trademarks and registered trademarks are the property
of their respective owners.
All rights reserved.
Statement af Conditions
In the interest of improving internal design, operational
function, and/or reliability, NETGEAR reserves the right
to make changes to the products described in this
document without notice. NETGEAR does not assume
any liability that may occur due to the use or application
of the product(s) or circuit layouKs) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified the NETGEAR Model AGM721T
and AGM721F Product Description has been
suppressed in accordance with the conditions set out in
the MBPT-AmhblVig 243/1991 and Vig 46/1992. The
operation of some equipment (for example, test
transmitters) in accordance with the regulations may,
however, be subject to certain restrictions. Please r^r to
the notes in the operating instructions. Federal OfRce For
Telecommunications Approvals has been notified of the
placing of this equipment on the market and has been
granted the right to test the series for compliance with
the regulations.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model AGM721T
and AGM721F Product Description is shielded against
the generation of radio interference in accordance with
the application of Council Directive 89/336/EEC,
Article 4a. Conformity is declared by the application of
EN 55 022 Class A (CISPR 22)
FCC Compliance Notice: Radio Frequency Notice
Federal Communications Commission (FCC) Compliance
Notice: Radio Frequency Notice
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device mush accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and Found to
comply with limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a commercial installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case users will be required to take
whatever measures may be necessary to correct the
interference at their own expense.
Warning
Warning Class 1 laser product. (AGM721F)
Warning Class 1 LED product. (AGAA721F)
Warning Because invisible laser radiation may be
emitted from the aperture of the port when no fiber
cable is connected, avoid exposure to laser radiation
and do not stare into open apertures.(AGM721 F)
Specifications
Standads AGM721T:
AGM721F:
Dimensions
(HxWxD)
Connectors
Weight
Operating temperature
Storage temperature
Operating relative humidity
Operating altitude
Power consumption
MTBF
Safety Certifications
IEEE802.3ab
lOOOBASE-T
Gigabit Ethernet
IEEE802.3Z
1000BASE-SX
Gigabit Ethernet
0.48 X 1.35x2.56 in
(1.22x3.44x6.5 cm)
RJ-45 for Cat5 cable
(AGM721T)
SC for 62.5um or 50um
cable(AGM721F)
0.11 lb (0.05 kg)
32toll3“F (0to45°C)
-4lol49“F (-10lo65“C)
10 to 85% noncondensing
up tol 0,000-ft (3000 m)
500mW
356000 hours
UL1950
CSA22.2 No. 950
NETGEAR
Bvarybedy't sonntoting.
M1-AGM721NA-0
Loading...