NEC X554UN, X464UNV-2, X464UN, P703-PC, P703 User Manual

...

Download

External Control NEC LCD Monitor

Rev.2.0 (G2)

INDEX

I. Application

................................................................................ 4

II. Preparation

2. Connectors and wiring

2.1 RS-232C Remote control

2.2 LAN control

III. Communication specification

3. Communication Parameter

3.1 RS-232C Remote control

3.2 LAN control

3.3 Communication timing

4. Communication Format

4.1 Header block format (fixed length)

4.2 Message block format

4.3 Check code

4.4 Delimiter

5. Message type

5.1 Get current Parameter from a monitor.

............................................................................... 5

.................................................................... 5

............................................................... 5

........................................................................... 5

............................................................... 7

................................................................ 7

............................................................... 7

........................................................................... 7

................................................................. 7

................................................................... 8

................................................................ 11

.......................................................................... 13

............................................................................ 14

........................................................................... 15

...................................................... 9

................................................. 15

5.2 "Get parameter" reply

5.3 Set parameter

5.4 "Set parameter" reply

5.5 Commands

5.5.1 Save Current Settings

5.5.2 Get Timing Report and Timing reply.

5.5.3 NULL Message

IV. Control Commands

6. Typical procedure example

6.1. How to change the “Backlight” setting.

6.2. How to read the measurement value of the built-in temperature sensors.

6.3. Operation Code (OP code) Table

7. Power control procedure

7.1 Power status read

7.2 Power control

8. Asset Data read and write

........................................................................ 18

........................................................................... 20

....................................................................... 23

........................................................................ 46

................................................................. 16

................................................................. 19

. ............................................................ 20

................................................ 21

.................................................................... 22

............................................................... 23

................................................ 23

....................................................... 29

................................................................. 44

.................................................................... 44

................................................................ 48

.................. 26

8.1 Asset Data Read Request and reply

.................................................... 48

(1/141)

8.2 Asset Data write

..................................................................... 50

9. Date & Time read and write

9.1 Date & Time Read

9.2 Date & Time Write

10. Schedule read and write

10.1 Schedule Read

10.2 Schedule Write

11. Self diagnosis

11.1 Self-diagnosis status read

12. Serial No. & Model Name Read

12.1 Serial No. Read

12.2 Model Name Read

13. Security Lock

13.1 Security Lock Control

14. Direct TV Chanel Read & Write

14.1 Direct TV Chanel Read & Reply

14.2 Direct TV Chanel Write & Reply

...................................................................... 57

...................................................................... 62

.......................................................................... 72

...................................................................... 74

.......................................................................... 78

.............................................................. 52

.................................................................... 52

.................................................................... 54

................................................................ 57

............................................................ 72

................................................................... 76

................................................................ 78

.......................................................... 74

.......................................................... 80

....................................................... 80

....................................................... 81

15. Daylight Saving read & write

15.1 Daylight Saving Read

15.2 Daylight Saving Write

16. Firmware Version

16.1 Firmware Version Read

17. Auto ID

17.1 Auto ID Execute

17.2 Auto ID Complete

17.3 Auto ID Reset

18. Input Name

18.1 Input Name Read

18.2 Input Name Write

18.3 Input Name Reset

19. Auto Tile Matrix

19.1 Auto Tile Matrix Execute

19.2 Auto Tile Matrix Complete

................................................................................ 88

....................................................................... 92

............................................................................ 93

........................................................................ 99

................................................................ 82

................................................................ 84

...................................................................... 86

.............................................................. 86

..................................................................... 88

.................................................................... 90

.................................................................... 93

.................................................................... 95

................................................................... 97

............................................................ 82

............................................................. 99

........................................................... 101

19.3 Auto Tile Matrix Monitors Read

19.4 Auto Tile Matrix Monitors Write

19.5 Auto Tile Matrix Reset

20. Power Save Mode

20.1 Power Save Mode Read

..................................................................... 109

.............................................................. 107

............................................................. 109

...................................................... 103

...................................................... 105

(2/141)

20.2 Power Save Mode Write

............................................................. 111

20.3 Auto Power Save Time Read

20.4 Auto Power Save Time Write

20.5 Auto Standby Time Read

20.6 Auto Standby Time Write

21. Setting Copy

21.1 Setting Copy Read

21.2 Setting Copy Write

21.3 Setting Copy Start

22. Security Enable

22.1 Security Enable Read

22.2 Security Enable Write

23. LAN MAC Address

.......................................................................... 119

.................................................................. 119

.................................................................. 121

.................................................................. 123

....................................................................... 125

............................................................... 125

............................................................... 127

..................................................................... 129

23.1 LAN MAC Address Read

24. Proof of Play

24.1 Start Proof of Play

24.2 Stop Proof of Play

.......................................................................... 131

.................................................................. 131

.................................................................. 133

......................................................... 113

........................................................ 114

............................................................ 116

............................................................ 117

............................................................. 129

24.3 Get Proof of Play Current

24.4 Get Proof of Play Total Number

............................................................ 135

...................................................... 137

24.5 Get Proof of Play Number to Number

................................................. 139

(3/141)

I. Application

This document defines the communications method for control of the NEC LCD monitor, MultiSync P403/

P463 /P553 /P703 /P801 /X464UN /X554UN /X464UNV /X554UNS when using an external controller.

(4/141)

II. Preparation

2. Connectors and wiring

2.1 RS-232C Remote control

Connector: 9-pin D-Sub Cable: Cross (reversed) cable or null modem cable

(Please refer “Controlling the LCD monitor via RS-232C Remote control” on User’s manual.)

2.2 LAN control

Connector: RJ-45 10/100 BASE-T Cable: Category 5 or higher LAN cable

(5/141)

(Please refer “Controlling the LCD monitor via LAN control” on User’s manual.)

(6/141)

III. Communication specification

3. Communication Parameter

3.1 RS-232C Remote control

(1) Communication system Asynchronous (2) Interface RS-232C (3) Baud rate 9600bps (4) Data length 8bits (5) Parity None (6) Stop bit 1 bit (7) Communication code ASCII

3.2 LAN control

(1) Communication system TCP/IP (Internet protocol suite) (2) Interface Ethernet (CSMA/CD) (3) Communication layer Transport layer (TCP) * Using the payload of TCP segment. (4) IP address (Default) Automatic setup * If you need to change, Please refer “Network settings” on User’s manual. (5) Port No. 7142 (Fixed)

(Note) The monitor will disconnect the connection if no packet data is received for 15 minutes. And the controller (PC) has to re-connect to control the monitor again, after 15 minutes or more.

3.3 Communication timing

The controller should wait for a reply packet before next command is sent. (Note) A normal answer cannot be performed when a monitor is a busy state. Please refer “5.5.3 NULL message”.

(7/141)

Header

Delimiter

Set Parameter

Get Parameter Reply

Get Parameter

Header

Delimiter

Header

Delimiter

Header

Delimiter

Header

Delimiter

Header

Delimiter

Header

Delimiter

Header

Delimiter

Header

Delimiter

Header

Delimiter

4. Communication Format

Header Message Check Code Delimiter

The command packet consists of four parts, Header, Message, Check code and Delimiter.

Recommended sequence of a typical procedure to control a monitor is as follows,

[A controller and a monitor, two-way communication composition figure]

■ For the general command (see the part "6.3. Operation Code (OP code) Table”)

Get Parameter

Message

Check Code

Get Parameter Reply

Message

Check Code

Message

Check Code

Set Parameter Reply

Message

Check Code

Message

Check Code

Message

Check Code

Save Current Setting Command

Message

Check Code

Save Current Setting Command Reply

Message

Check Code

Monitor Controller

The controller sends command to get a value from the monitor that you want to change.

The monitor replies a current value of the requested item.

The controller sends commands to set an adjusted value.

The monitor replies to the controller for confirmation.

The controller sends command to get a value for confirmation.

The monitor replies an adjusted value.

The controller requests to store the adjusted value to the monitor.

The monitor replies to the controller for confirmation.

■ For the special command (see the part 7 to 24. and 5.5.2)

Command

Message

Command Reply

Message

Check Code

(8/141)

Monitor Controller

The control does not suitable for above fixed protocol; use the proper command for each control. Please refer section 5.5 and section 7 to 24.

The monitor replies a proper message defined for each control.

Destination

Header

4.1 Header block format (fixed length)

Message Check code Delimiter

SOH Reserved

'0'

1st 2nd 3rd 4th 5th 6th -7th

Destination

Source Message

Type

Message

Length

1stbyte) SOH: Start of Header

ASCII SOH (01h)

byte) Reserved: Reserved for future extensions.

On this monitor, it must be ASCII '0'(30h).

byte) Destination: Destination equipment ID. (Receiver)

Specify a commands receiver’s address.

The controller sets the “MONITOR ID” or “GROUP ID” of the monitor controlled in here.

On the reply, the monitor sets ‘0’ (30h), always.

“MONITOR ID”, “GROUP ID” to “Destination Address” conversion table is as follows,

Monitor ID

1 41h(‘A’) 26 5Ah(‘Z’) 51 73h 76 8Ch 2 42h(‘B’) 27 5Bh 52 74h 77 8Dh 3 43h(‘C’) 28 5Ch 53 75h 78 8Eh 4 44h(‘D’) 29 5Dh 54 76h 79 8Fh 5 45h(‘E’) 30 5Eh 55 77h 80 90h 6 46h(‘F’) 31 5Fh 56 78h 81 91h 7 47h(‘G’) 32 60h 57 79h 82 92h 8 48h(‘H’) 33 61h 58 7Ah 83 93h 9 49h(‘I’) 34 62h 59 7Bh 84 94h 10 4Ah(‘J’) 35 63h 60 7Ch 85 95h 11 4Bh(‘K’) 36 64h 61 7Dh 86 96h 12 4Ch(‘L’) 37 65h 62 7Eh 87 97h 13 4Dh(‘M’) 38 66h 63 7Fh 88 98h 14 4Eh(‘N’) 39 67h 64 80h 89 99h 15 4Fh(‘O’) 40 68h 65 81h 90 9Ah 16 50h(‘P’) 41 69h 66 82h 91 9Bh 17 51h(‘Q’) 42 6Ah 67 83h 92 9Ch 18 52h(‘R’) 43 6Bh 68 84h 93 9Dh 19 53h(‘S’) 44 6Ch 69 85h 94 9Eh 20 54h(‘T’) 45 6Dh 70 86h 95 9Fh 21 55h(‘U’) 46 6Eh 71 87h 96 A0h 22 56h(‘V’) 47 6Fh 72 88h 97 A1h 23 57h(‘W’) 48 70h 73 89h 98 A2h 24 58h(‘X’) 49 71h 74 8Ah 99 A3h 25 59h(‘Y’) 50 72h 75 8Bh 100 A4h ALL 2Ah(‘*’)

Group ID

A 31h(‘1’) D 34h(‘4’) G 37h(‘7’) J 3Ah(‘:’) B 32h(‘2’) E 35h(‘5’) H 38h(‘8’) C 33h(‘3’) F 36h(‘6’) I 39h(‘9’)

Destination Address

Monitor ID

Group ID

Address

Destination Address

Monitor ID

Group ID

Destination Address

Address

Monitor ID

Group ID

Address

Destination Address

(9/141)

Ex.) If you want to control a monitor that has the "ID No." as '1', specify a destination address

'A'(41h). If you want to control all of the monitors which are connected by a daisy chain, specify

a destination address ‘*’(2Ah).

byte) Source: Source equipment ID. (Sender)

Specify a sender address.

The controller must be ‘0’ (30h).

On the reply, the monitor sets the own MONITOR ID in here.

byte) Message Type: (Case sensitive.)

Refer to section 4.2 “Message block format” for more details.

ASCII 'A' (41h): Command.

ASCII 'B' (42h): Command reply.

ASCII 'C' (43h): Get current parameter from a monitor.

ASCII 'D' (44h): "Get parameter" reply.

ASCII 'E' (45h): Set parameter.

ASCII 'F' (46h): "Set parameter" reply.

-7th bytes) Message Length:

Specify the length of the message (that follows the header) from STX to ETX.

This length includes STX and ETX.

The byte data must be encoded to ASCII characters.

Ex.) The byte data 3Ah must be encoded to ASCII characters '3' and 'A' (33h and 41h).

The byte data 0Bh must be encoded to ASCII characters '0' and 'B' (30h and 42h).

(10/141)

Message

Hi Lo Hi Lo Hi Lo Hi Lo

4.2 Message block format

“Message block format” is allied to the “Message Type” in the “Header”.

Refer to the section 4.1 “Header block format” for more detail.

1)Get current parameter

The controller sends this message when you want to get the status of the monitor.

For the status that you want to get, specify the “OP code page” and “OP code”,

refer to “Appendix A. Operation code table”.

“Message format” of the “Get current parameter” is as follows,

2)Get Parameter reply

The monitor will reply with the status of the requested item specified by the controller

in the “Get parameter message”.

“Message format” of the “Get parameter reply” is as follows,

STX Result OP code

Hi Lo Hi Lo Hi Lo Hi Lo MSB

STX OP code

page

Lo Hi Lo

Refer to section 5.1 “Get current parameter from a monitor.” for more details.

OP code

page

Refer to section 5.2 “Get parameter reply” for more details.

Header

OP code

Check code Delimiter

ETX

Type Max value Current Value ETX

LSB MSB

LSB

3)Set parameter

The controller sends this message to change a setting of the monitor.

Message format of the “Set parameter” is as follows,

STX

4)Set Parameter reply

The monitor replies with this message for a confirmation of the “Set parameter message”.

STX

5)Command

Result OP code

“Command message” format depends on each command.

OP code

page

Hi Lo Hi Lo MSB

Refer to section 5.3 “Set parameter” for more details.

Message format of the “Set parameter reply” is as follows,

page

Refer to section 5.4 “Set parameter reply” for more details.

OP code

Set Value ETX

LSB

Type Max value Requested setting

MSB

Value

LSB MSB

ETX

LSB

Usually, this “command message” is used for some non-slider controls and some special operations,

(11/141)

such as “Save current settings”, “Get timing report”, “power control”, “Schedule”, etc. Refer to

section 5.5 “Commands message” for more details.

6)Command reply

The monitor replies to a query from the controller.

“Command reply message” format depends on each command.

Refer to section 5.5 “Commands message” for more details.

(12/141)

Check code

n+1

Header

Message

Check

Delimiter

SOH Reserved

Destination

Source

Message

length STX OP code

OP code

Set Value

ETX

4.3 Check code

Header Message

Check code is the Block Check Code (BCC) between the Header and the End of Message except SOH.

27 26 25 24 23 22 21 20 SOH D0 Reserved D1 Destination D2 Source D3 Type D4 Length(H) D5 Length(L) D6 STX D7 Data D8 | | | | ETX Dn Check code D

P P P P P P P P

= D1 XOR D2 XOR D3 XOR ,,, D

n+1

XOR: Exclusive OR

Delimiter

Following is an example of a Check code (BCC) calculation.

code

Address

type

page

(BCC)

01 30 41 30 45 30 41 02 30 30 31 30 30 30 36 34 03 77

D1 D2 D3 D4 D5 D6 D7 D

Check code (BCC) D

= D1 xor D2 xor D3 xor … xor D14 xor D15 xor D16

= 30h xor 41h xor 30h xor 45h xor 30h xor 41h

xor 02h xor 30h xor 30h xor 31h xor 30h xor 30h

xor 30h xor 36h xor 34h xor 03h

= 77h

D18

(13/141)

Delimiter

4.4 Delimiter

Packet delimiter code; ASCII CR(0Dh).

Header Message Check code

(14/141)

5. Message type

5.1 Get current Parameter from a monitor.

STX OP code

page

Lo Hi Lo

1st 2nd-3rd 4th–5th 6th

OP code ETX

Send this message when you want to get the status of a monitor.

For the status that you want to get, specify the “OP code page” the “OP code”, refer to “Appendix

A. Operation code table”.

byte) STX: Start of Message

ASCII STX (02h)

nd-3rd

bytes) OP code page: Operation code page.

Specify the “OP code page” for the control which you want to get the status.

Refer to “Appendix A Operation code table” for each item.

OP code page data must be encoded to ASCII characters.

Ex.) The byte data 02h must be encoded to ASCII characters '0' and '2' (30h and 32h).

OP code page 02h -> OP code page (Hi) = ASCII '0' (30h)

OP code page (Lo) = ASCII '2' (32h)

Refer to Operation code table. (Appendix A)

th–5th

bytes) OP code: Operation code

Refer to “Appendix A Operation code table” for each item.

OP code data must be encoded to ASCII characters.

Ex.) The byte data 3Ah must be encoded to ASCII characters '3' and 'A' (33h and 41h).

OP code 3Ah -> OP code (Hi) = ASCII '3' (33h)

OP code (Lo) = ASCII 'A' (41h)

Refer to Operation code table.

byte) ETX: End of Message

ASCII ETX (03h)

(15/141)

Hi Lo Hi Lo Hi Lo Hi Lo

5.2 "Get parameter" reply

STX

Result OP code

OP code Type Max value Current Value ETX

page

MSB

2nd-3rd 4th–5th 6th –7th 8th -9th 10th -13th 14

LSB MSB

LSB

-17th 18

The monitor replies with a current value and the status of the requested item (operation code).

byte) STX: Start of Message

ASCII STX (02h)

nd-3rd

bytes) Result code.

These bytes indicate a result of the requested commands as follows,

00h: No Error.

01h: Unsupported operation with this monitor or unsupported operation under current condition.

This result code from the monitor is encoded to ASCII characters.

Ex.) The byte data 01h is encoded to ASCII character '0' and '1' (30h and 31h).

th–5th

bytes) OP code page: Operation code page.

These bytes indicate a replying item's OP code page.

This returned value from the monitor is encoded to ASCII characters.

Ex.) The byte data 02h is encoded to ASCII character '0' and '2' (30h and 32h).

Refer to the operation code table.

–7thbytes) OP code: Operation code

These bytes indicate a replying item's OP code.

This returned value from the monitor is encoded to ASCII characters.

Refer to the operation code table.

Ex.) The byte data 1Ah is encoded to ASCII character '1' and 'A' (31h and 41h).

-9thbytes) Type: Operation type code

00h: Set parameter

01h: Momentary

Like the Auto Setup function which automatically changes the parameter.

This returned value from the monitor is encoded to ASCII characters.

Ex.) The byte data 01h is encoded to ASCII character '0' and '1' (30h and 31h).

-13thbytes) Max. value: Maximum value which monitor can accept. (16bits)

This returned value from the monitor is encoded to ASCII characters.

Ex.) '0','1','2' and '3' means 0123h (291)

-17thbytes) Current Value: (16bits)

This returned value from the monitor is encoded to ASCII characters.

Ex.) '0','1','2' and '3' means 0123h (291)

(16/141)

18thbyte) ETX: End of Message

ASCII ETX (03h)

(17/141)

5.3 Set parameter

STX

OP code

OP code Set Value ETX

page

Hi Lo Hi Lo MSB

2nd-3rd 4th-5th 6th-9th 10

LSB

Send this message to change monitor’s adjustment and so on.

The controller requests a monitor to change value.

byte) STX: Start of Message

ASCII STX (02h)

nd-3rd

bytes) OP code page: Operation code page

This OP code page data must be encoded to ASCII characters.

Ex.) The byte data 02h must be encoded to ASCII '0' and '2' (30h and 32h).

Refer to the Operation code table.

th-5th

bytes) OP code: Operation code

This OP code data must be encoded to ASCII characters.

Ex.) OP code 1Ah -> OP code (Hi) = ASCII '1' (31h)

OP code (Lo) = ASCII 'A' (41h)

Refer to the Operation code table.

th-9th

bytes) Set value: (16bit)

This data must be encoded to ASCII characters.

Ex.) 0123h -> 1

byte) ETX: End of Message

(MSB) = ASCII '0' (30h)

= ASCII '1' (31h)

= ASCII '2' (32h)

(LSB) = ASCII '3' (33h)

ASCII ETX (03h)

(18/141)

5.4 "Set parameter" reply

STX

Result OP code

page

Hi Lo Hi Lo Hi Lo Hi Lo MSB

2nd-3rd 4th-5th 6th-7th 8th-9th 10th-13th 14th -17th 18

OP code Type Max value Requested setting

Value

LSB MSB

The Monitor echoes back the parameter and status of the requested operation code.

byte) STX: Start of Message

ASCII STX (02h)

nd-3rd

bytes) Result code

ASCII '0''0' (30h, 30h): No Error.

ASCII '0''1' (30h, 31h): Unsupported operation with this monitor or unsupported operation under

current condition.

th-5th

bytes) OP code page: Echoes back the Operation code page for confirmation.

Reply data from the monitor is encoded to ASCII characters.

Ex.) OP code page 02h -> OP code page = ASCII '0' and '2' (30h and 32h)

Refer to Operation code table.

th-7th

bytes) OP code: Echoes back the Operation code for confirmation.

Reply data from the monitor is encoded to ASCII characters.

ETX

LSB

Ex.) OP code 1Ah -> OP code (Hi) = ASCII '1' (31h)

OP code (Lo) = ASCII 'A' (41h)

Refer to Operation code table

th-9th

bytes) Type: Operation type code

ASCII '0''0' (30h, 30h): Set parameter

ASCII '0''1' (30h, 31h): Momentary

Like Auto Setup function, that automatically changes the parameter.

-13thbytes) Max. value: Maximum value that monitor can accept. (16bits)

Reply data from the monitor is encoded to ASCII characters.

Ex.) '0''1''2''3' means 0123h (291)

-17thbytes) Requested setting Value: Echoes back the parameter for confirmation. (16bits)

Reply data from the monitor is encoded to ASCII characters.

Ex.) '0''1''2''3' means 0123h (291)

byte) ETX: End of Message

ASCII ETX (03h)

(19/141)

5.5 Commands

"Command message format" depends on each command. Some commands are shown with usage. Refer to section

7 to 13.

5.5.1 Save Current Settings.

The controller requests for the monitor to store the adjusted value.

Command code

STX

'0' 'C'

ASCII: 01h-30h-41h-30h-41h-30h-34h-02h-30h-43h-03h-CHK-0Dh

The monitor replies the packet for confirmation as follows;

SOH-'0'-'0'-'A'-'B'-'0'-'6'-STX-'0'-'0'-'0'-'C'-ETX-CHK- CR

Send "OC"(30h, 43h) as Save current settings command.

Complete "Save Current setting" command packet as follows;

SOH-'0'-'A'-'0'-'A'-'0'-'4'-STX-'0'-'C'-ETX-CHK- CR

ETX

(20/141)

5.5.2 Get Timing Report and Timing reply.

The controller requests the monitor to report the displayed image timing.

STX

ASCII: 01h-30h-41h-30h-41h-30h-34h-02h-30h-37h-03h-CHK-0Dh

The monitor replies status as the following format;

STX

Command code '0' '7'

Send "07"(30h, 37h) as Get Timing Report command.

Complete "Get Timing Report" command packet as follows;

SOH-'0'-'A'-'0'-'A'-'0'-'4'-STX-'0'-'7'-ETX-CHK- CR

Command SS H Freq. V Freq. ETX

'4' 'E' Hi Lo MSB

SS: Timing status byte

Bit 7 = 1: Sync Frequency is out of range.

Bit 6 = 1: Unstable count Bit 5-2 Reserved (Don't care) Bit 1 1:Positive Horizontal sync polarity. 0:Negative Horizontal sync polarity. Bit 0 1:Positive Vertical sync polarity.

0:Negative Vertical sync polarity.

H Freq: Horizontal Frequency in unit 0.01kHz

V Freq: Vertical Frequency in unit 0.01Hz

ETX

LSB

MSB

LSB

Ex.) When H Freq is '1''2''A''9' (31h, 32h, 41h, 39h), it means 47.77kHz.

(21/141)

5.5.3 NULL Message

STX

The NULL message returned from the monitor is used in the following cases;

Command code 'B' 'E'

To tell the controller that the monitor does not have any answer to give to the host (not

ready or not expected)

Following operation s need 15 seconds for to execute, so the monitor will return this message

when another message is received during execution.

Power ON and Power OFF

Following operations need 10 seconds for to execute, so the monitor will return this message

when another message is received during execution.

Auto Setup, Input, PIP Input, Auto Setup and Factory reset.

A null message will be returned by the monitor if the “Start Proof of Play” command is sent

and the monitor has already started Proof of Play.

A null message will be returned by the monitor if the “Stop Proof of Play” command is sent

and the monitor has not started Proof of Play.

Complete "NULL Message" command packet as follows;

ETX

01h-30h-30h-41h-42h-30h-34h-02h-42h-45h-03h-CHK-0Dh

SOH-'0'-'0'-'A'-'B'-'0'-'4'-STX-'B'-'E'-ETX-CHK- CR

(22/141)

IV. Control Commands

6. Typical procedure example

The following is a sample of procedures to control the monitor, these are examples of "Get parameter",

"Set parameter" and "Save current settings".

6.1. How to change the “Backlight” setting.

Step 1. The controller requests the Monitor to reply with the current brightness setting and capability

to support this operation. (Get parameter)

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'C'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID from which you want to get a value.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'C' (43h): Message type is "Get parameter command". '0'-'6' (30h, 36h): Message length is 6 bytes.

Message

STX (02h): Start of Message '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the OP code page 0). ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Step 2. The monitor replies with current Backlight setting and capability to support this operation.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'D'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller.

Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'D' (44h): Message Type is "Get parameter reply". '1'-'2' (31h, 32h): Message length is 18 bytes.

Message

STX (02h): Start of Message

'0'-'0' (30h, 30h): Result code. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0' (30h, 30h): This operation is "Set parameter" type. '0'-'0'-'6'-'4' (30h, 30h, 36h, 34h): Backlight max value is 100(0064h). '0'-'0'-'3'-'2' (30h, 30h, 33h, 32h): Current Backlight setting is 50(0032h) . ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

STX-'0'-'0'-'1'-'0'-ETX BCC CR

STX-'0'-'0'-'0'-'0'-'1'-'0'-'0'-'0'

-'0'-'0'-'6'-'4'-'0'-'0'-'3'-'2'-ETX

Delimiter

BCC CR

(23/141)

Delimiter

CR (0Dh): End of packet

Step 3. The controller request the monitor to change the Backlight setting

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'E'-'0'-'A'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'E' (45h): Message Type is "Set parameter command". '0'-'A' (30h, 41h): Message length is 10 bytes.

Message

STX (02h): Start of Message

'0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Set Backlight setting 80(0050h). ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Step 4. The monitor replies with a message for confirmation.

Header Message Check

SOH-'0'-'0'- Monitor ID –

'F'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'.

'F' (46h): Message Type is "Set parameter reply".

'1'-'2' (31h, 32h): Message length is 18 bytes.

Message

STX (02h): Start of Message

'0'-'0' (30h, 30h): Result code. No error. '0'-'0' (30h, 30h): Operation code page number is 0. '1'-'0' (31h, 30h): Operation code is 10h (in the page 0). '0'-'0' (30h, 30h): This operation is "Set parameter" type. '0'-'0'-'6'-'4' (30h, 30h, 36h, 34h): Backlight max value is 100(0064h). '0'-'0'-'5'-'0' (30h, 30h, 35h, 30h): Received a Backlight setting was 80(0050h) . ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'0'-'0'-'1'-'0'-

'0'-'0'-'5'-'0'-ETX

STX-'0'-'0'-'0'-'0'-'1'-'0'—'0'-'0'-

'0'-'0'-'6'-'4'-'0'-'0'-'5'-'0'-ETX

BCC CR

Delimiter

code

BCC CR

Delimiter

(24/141)

Repeat Step 1 and Step 2, if you need to check the Backlight setting. (Recommended)

Step 5. Request the monitor to store the Backlight setting. (Save Current Settings Command)

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'4'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to store the setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'4' (30h, 34h): Message length is 4 bytes.

Message

STX (02h): Start of Message '0'-'C' (30h, 43h): Command code is 0Ch as "Save current settings". ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'0-'C'-ETX BCC CR

Delimiter

(25/141)

6.2. How to read the measurement value of the built-in temperature sensors.

MultiSync P403/ P463 /P553 /P703 /P801 /X464UN /X554UN /X464UNV /X554UNS have three built-in

temperature sensors.

The controller can monitor inside temperatures by using those sensors with external control.

The following shows the procedure for reading the temperatures from the sensors.

Step 1. Select a temperature sensor which you want to read.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'E'-'0'-'A'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get a value.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'E' (45h): Message Type is "Set parameter command". '0'-'A' (30h, 41h): Message length is 10 bytes.

Message

STX (02h): Start of Message

'0'-'2' (30h, 32h): Operation code page number is 2. '7'-'8' (37h, 38h): Operation code is 78h (on page 2). '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Select the temperature sensor #1 (01h).

00h: No meaning 01h: Sensor #1 02h: Sensor #2 03h: Sensor #3

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Step 2. The monitor replies for confirmation.

STX-'0'-'2'-'7'-'8'-

'0'-'0'-'0'-'1'-ETX

BCC CR

Delimiter

Header Message Check code Delimiter

SOH-'0'-'0'-Monitor ID-

'F'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicates a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'F' (46h): Message Type is "Set parameter reply". '1'-'2' (31h, 32h): Message length is 18 bytes.

Message

STX (02h): Start of Message

'0'-'0' (30h, 30h): Result code. No error. '0'-'2' (30h, 32h): Operation code page number is 2.

STX-'0'-'0'-'0'-'2'-'7'-'8'-'0'-'0'-

'0'-'0'-'0'-'3'-'0'-'0'-'0'-'1'-ETX

(26/141)

BCC CR

'7'-'8' (37h, 38h): Operation code is 78h (in the page 2). '0'-'0' (30h, 30h): This operation is "Set parameter" type. '0'-'0'-'0'-'3' (30h, 30h, 30h, 33h): Number of temperature sensors are 3 (0003h). '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): temperature sensor is #1. ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Step 3. The controller requests the monitor to send the temperature from the selected sensor.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'C'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get a value.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'C' (43h): Message Type is "Get parameter". '0'-'6' (30h, 36h): Message length is 6 bytes.

Message

STX (02h): Start of Message

'0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Step 4. The monitor replies a temperature of selected sensor.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'D'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'D' (44h): Message Type is "Get parameter reply". '1'-'2' (31h, 32h): Message length is 18 bytes.

Message

STX (02h): Start of Message

'0'-'0' (30h, 30h): Result code. No error. '0'-'2' (30h, 32h): Operation code page number is 2. '7'-'9' (37h, 39h): Operation code is 79h (in the page 2). '0'-'0' (30h, 30h): This operation is "Set parameter" type. 'F'-'F'-'F'-'F' (46h, 46h, 46h, 46h): Maximum value. '0'-'0'-'3'-'2' (30h, 30h, 33h, 32h): The temperature is 25 degrees Celsius.

STX-'0'-'2'-'7'-'9'-ETX BCC CR

STX-'0'-'0'-'0'-'2'-'7'-'9'-'0'-'0'

-'F'-'F'-'F'-'F'-'0'-'0'-'3'-'2'-ETX

Delimiter

BCC CR

(27/141)

Readout value is 2's complement.

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Temperature [Celsius]

+125.0 0000 0000 1111 1010 00FAh + 25.0 0000 0000 0011 0010 0032h + 0.5 0000 0000 0000 0001 0001h 0 0000 0000 0000 0000 0000h

- 0.5 1111 1111 1111 1111 FFFFh

- 25.0 1111 1111 1100 1110 FFCEh

- 55.0 1111 1111 1001 0010 FF92h

Readout value Binary Hexadecimal

(28/141)

6.3. Operation Code (OP code) Table

Item OP

code page

BACKLIGHT 00h 10h 0: dark

CONTRAST 00h 12h 0: low

SHARPNESS 00h 8Ch 0: dull

BRIGHTNESS 00h 92h 0: dark

HUE 00h 90h 0: purplish

COLOR 02h 1Fh 0: pale

COLOR TEMPERATURE 00h 54h 0:2600K

COLOR TEMPERATURE (CUSTOM) R GAIN 00h 16h 0: Dark

B GAIN 00h 18h 0: Dark

G GAIN 00h 1Ah 0: Dark

00h 14h 9: 10000K

PICTU R E

COLOR CONTROL 00h RED:

GAMMA CORRECTION 02h 68h 0: No mean

MOVIE SETTINGS

ADAPTIVE CONTRAST

NOISE REDUCTION 02h 26h 0: Off

02h 8Dh 0: No mean

OP code Parameter Remarks

| 100(64h): bright

| 100(64h): high

| 24(18h): sharp

| 100(64h): bright

| 100(64h): greenish

| 100(64h): deep

| 74(4Ah):10000K

11(0Bh): CUSTOM

| 255(FFh): Bright

0: 9Bh YELLOW: 9Ch GREEN: 9Dh CYAN: 9Eh BLUE: 9Fh MAGENTA: A0h

100(64h):(center)

200(C8h):

1: NATIVE

4: 2.2

8: 2.4

7: S GAMMA

5: DICOM SIM.

6: PROGRAMABLE1

13(0Bh): PROGRAMABLE2

14(0Ch): PROGRAMABLE3

1: Off

2: LOW

4: High

7: High

100K/step

Page02 OPcode20h also works as same.

(29/141)

Item OP

code page

TELECINE 02h 23h 0: No mean

PICTURE MODE 02h 1Ah 0: No mean

RESET (PICTURE)

AUTO SETUP 00h 1Eh 0: No mean

AUTO ADJUST 10h B7h 0: No mean

H POSITION 00h 20h 0: Left side

V POSITION 00h 30h 0: Bottom side

CLOCK 00h 0Eh 0:

02h CBh 0: No mean

ADJUS T

PHASE 00h 3Eh 0:

H RESOLUTION 02h 50h 0: Low

V RESOLUTION 02h 51h 0: Low

OP code Parameter Remarks

1: Off

2: Auto

1: sRGB

3: HIGHBRIGHT

4: STANDARD

5: CINEMA

8: CUSTOM1

9: CUSTOM2

2: Reset

Picture category

1: Execute

1: OFF 2: ON

Max.: Right side

Max.: Top side

Max. :

Max. : High

Max.: High

sRGB:

PC mode only

CINEMA:

A/V mode only

Momentary

Depends on a display timing

(30/141)

commands can also

Item OP

code page

INPUT RESOLUTION 02h DAh Input Resolution select

ASPECT 02h 70h 0: No mean

Zoom Control ZOOM 11h 2Ch 0-89(59h): No mean

H ZOOM 11h 2Dh 0-89(59h): No mean

OP code Parameter Remarks

0:No mean 1:Item 1(always Auto) 2:Item 2 3:Item 3 4:Item 4 5:Item 5

Ex) Item 1= AUTO

Item 2= -- /

1024x768 / 1400x1050 / 800x600 / 1280x960

Item 3= -- /

1280x768 / 1680x1050 / 1024x576 / 1600x900 /

Item 4= -- /

1360x768 /

-- /

Item 5= -- /

1366x768

-- /

1: NORMAL

2: FULL

3: WIDE

4: ZOOM

6: DYNAMIC

7: 1:1

90(5Ah): 90%

91(5Bh): 91%

100(64h): 100%

300(12Ch): 300%

90(5Ah): 90%

91(5Bh): 91%

100(64h): 100%

300(12Ch): 300%

Wide: Dynamic A/V mode only

The following

be used. OP code page 02h OP code 6Fh Parameter 0: No mean 1: 100% 2: 101% | 201(C9h): 300% The following

be used. OP code page 02h OP code 6Ch Parameter 0: No mean 1: 100% 2: 101% | 201(C9h): 300%

(31/141)

commands can also

Item OP

code page

V ZOOM 11h 2Eh 0-89(59h): No mean

H POS 02h CCh 0: Left side

V POS 02h CDh 0: Down side

IMAGE FLIP 02h D7h 0: No mean

OSD FLIP 10h B8h 0: No mean

RESET (ADJUST)

VOLUME 00h 62h 0: whisper

BALANCE

TREBLE 00h 8Fh O: Min.

02h CBh 0: No mean

00h 93h O: Left

00h 94h 0: No mean

OP code Parameter Remarks

AUDI O

BASS 00h 91h 0: Min.

PIP AUDIO 10h 80h 0: No mean

LINE OUT 10h 81h 0: No mean

SURROUND 02h 34h 0: No mean

90(5Ah): 90%

91(5Bh): 91%

100(64h): 100%

300(12Ch): 300%

200(C8h): Right side

200(C8h): Up side

1: NONE

2: H FLIP

3: V FLIP

4: 180 ROTATE

1: OFF

2: ON

3: Reset

Adjust category

100(64h): loud

30(1Eh):(Center)

60(3Ch): Right

1: MONAURAL

2: STEREO

6:(Center)

12(0Ch): Max.

6:(Center)

12(0Ch): Max.

1: MAIN AUDIO

2: PIP AUDIO

1: FIXED

2: VARIABLE

1: OFF

2: ON

The following

be used. OP code page 02h OP code 6Dh Parameter 0: No mean 1: 100% 2: 101% | 201(C9h): 300%

Momentary

(32/141)

Item OP

code page

AUDIO INPUT 02h 2Eh 0: No mean

AUDIO DELAY 10h CAh 0: No mean

DELAY TIME 10h CBh 0: (small)

RESET (AUDIO)

OFF TIMER 02h 2Bh 0: Off

SCHEDULE

ENABLE 02h E5h 0: No mean

DISABLE 02h E6h 0: No mean

02h CBh 0: No mean

OP code Parameter Remarks

SCHDU L E

SCHEDULE SETTINGS Refer to chapter 10 DATE & TIME Refer to chapter 9 DAYLIGHT SAVING Refer to chapter 9 and 15

RESET (SCHEDULE)

KEEP PIP MODE 10h 82h 0: No mean

PIP MODE 02h 72h 0: No mean

PIP SIZE 10h B9h 0(small)

02h CBh 0: No mean

PI P

PIP POSITION

ASPECT 10h 83h 0: No mean

X 02h 74h 0: left

Y 02h 75h 0: top

1: IN1

2: IN2

3: IN3

4: HDMI

6: OPTION

7: DPORT

8: DPORT2

9: DPORT3

10(0Ah): HDMI2

1: OFF

2: ON

100(64h): (large)

Momentary 4: Reset Audio category

1 hour/step 1: 1 hour | 24(18h): 24 hours

1: No.1 Enable | 7: No.7 Enable

1: No.1 Disable | 7: No.7 Disable

Momentary 5: Reset Schedule category

1: OFF 2: ON

1: OFF 2: PIP 3: POP (4: STILL) 5: PICTURE BY PICTURE

- ASPECT

6: PICTURE BY PICTURE

- Full

| 80(large)

| 100(64h): right

| 100(64h): bottom

1: NORMAL 2: FULL 3: WIDE 4: ZOOM

(33/141)

has limitation of

Item OP

code page

TEXT TICKER MODE 10h 08h 0: No mean

POSITION 10h 09h 0: Top/Left

SIZE 10h 0Ah 0-1: Do not set.

BLEND 10h 0Bh 0: No mean

DETECT 10h 0Ch 0: No mean

FADE IN 10h 0Dh 0: No mean

PIP INPUT(SUB INPUT) 02h 73h 0: No mean

RESET (PIP)

LANGUAGE 00h 68h 0: No mean

MENU DISPLAY TIME 00h FCh 0-1: Do not set.

OS D

OSD POSITION X 02h 38h 0: Left

Y 02h 39h 0: Down

02h CBh 0: No mean

OP code Parameter Remarks

1: OFF 2: HORIZONTAL 3: VERTICAL

| 100(64h): Bottom/Right

2: Narrow(2/24) | 8: Wide(8/24)

1: 10% | 10(0Ah): 100%

1: AUTO 2: OFF

1: ON 2: OFF

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: VIDEO 7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 (SCART) 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 18(12h): HDMI2 128(80h): DPORT3

6: Reset PIP

Category

1: ENGLISH 2: GERMAN 3: FRENCH 4: SPANISH 5: JAPANESE 6: ITALIAN 7: SWEDISH 9: RUSSIAN 14(0Eh): CHINESE

2: 10s 3: 15s | 48(30h): 240s

| 255(FFh): Right

| 255(FFh): Up

This operation

selection.

Please refer to

the monitor

instruction

manual.

Momentary

OSD Language

5sec/step

(34/141)

commands can also

Item OP

OP code Parameter Remarks code page

INFORMATION OSD 02h 3Dh 0:Disable information

OSD 3-10(0Ah): OSD timer [seconds]

MONITOR

MODEL NAME Refer to chapter 12

INFORMATION

SERIAL Refer to chapter 12 FIRMWARE1 Refer to chapter 16

FIRMWARE2 Refer to chapter 16

CARBON SAVINGS

10h 10h

(g)

0 – 999(3E7h)(g) 0 – 65535(FFFF

ｈ

)(kg)

/11h

(kg) CARBON USAGE

10h 26h

(g)

/27h

0 – 999(3E7

ｈ

0 – 65535(FFFF

)(g)

ｈ

)(kg)

(kg)

OSD TRANSPARENCY 02h B8h 0: No mean

1: OFF 2: ON

OSD ROTATION 02h 41h 0: Landscape

1: Rotated

INPUT NAME Refer to chapter 18 NAME RESET

MEMO 10h BAh 0: No mean

1: Display a Memo

2: Undisplay a Memo RESET (OSD)

02h CBh 0: No mean

7: Reset

OSD category MONITOR ID 02h 3Eh 1-100:ID GROUP ID 10h 7Fh 0: No assignment

1: Group A 2: Group B 3: Group AB 4: Group C 5: Group AC | 1023(3FFh):Group

ABCDEFGHIJ

AUTO ID Refer to chapter 17 AUTO ID RESET Refer to chapter 17

IR LOCK SETTING

MODE SELECT 10h D4h 0: No mean

1: UNLOCK 2: ALL LOCK 3: CUSTOM LOCK

MULTI DIS P LA Y

POWER 10h D5h 0: No mean

1: UNLOCK 2: LOCK

VOLUME 10h D6h 0: No mean

1: UNLOCK 2: LOCK

MIN VOL 10h D7h 0 (whisper)

| 100(64h) (laud)

Read Only

Momentary

Bit0:Group A Bit1:Group B Bit2:Group C Bit3:Group D Bit4:Group E Bit5:Group F Bit6:Group G Bit7:Group H Bit8:Group I Bit9:Group J

The following

be used. OP code page 02h OP code 3Fh Parameter

0: No mean 1: NORMAL 4: LOCK

(35/141)

Item OP

code page

MAX VOL 10h D8h 0 (whisper)

INPUT 10h D9h 0: No mean

UNLOCK SELECT 10h DAh 0: No mean

10h DBh

10h DCh

TILE MATRIX H MONITOR 02h D0h 0: No mean

V MONITOR 02h D1h 0: No mean

POSITION 02h D2h 0: No mean

TILE COMP 02h D5h 0: No mean

ENABLE 02h D3h 0: No mean

FRAME COMP 11h 01h 0: No mean

AUTO 11h 02h 0: No mean

MANUAL 11h 03h 0: No mean

OP code Parameter Remarks

| 100(64h) (laud)

1: UNLOCK 2: LOCK

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: VIDEO 6: VIDEO2 7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 (SCART) 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 128(80h): DPORT3

1 | 10(0Ah)

1 | 100(64h)

1: NO 2: YES

1: NONE 2: AUTO 3: MANUAL

50(32h): 0.5F 100(64h): 1.0F 150(96h): 1.5F 200(C8h): 2.0F

25(19h): 0.25F 50(32h): 0.50F 75(4Bh): 0.75F 100(64h): 1.00F 125(7Dh): 1.25F 150(96h): 1.50F 175(Afh): 1.75F 200(C8h): 2.00F

Number of H-division

Number of V-division

Available on X464UN, X554UN, X464UNV, X554UNS

This command is used when FRAME COMP is set as “AUTO”. Available on X464UN, X554UN, X464UNV, X554UNS

This command is used when FRAME COMP is set as “MANUAL”.

(36/141)

V SCAN

is set as

Offset affects to

Item OP

code page

V SCAN REVERSE 11h 04h 0: No mean

MANUAL 11h 05h 0: No mean

TILE MATRIX MEM 10h 4Ah 0: No mean

AUTO TILE MATRIX SETIP Refer to chapter 19

POWER ON DELAY 02h D8h 0: Off (0sec)

LINK TO ID 10h BCh 0: No mean

VIDEO OUT SETTING 10h EAh 0: No mean

POWER INDICATOR 02h BEh 0: No mean

SETTING COPY Refer to Chapter 21 RESET (MULTI DISPLAY)

POWER SAVE Refer to Chapter 20 HEAT STATUS

FAN1/2/3 02h 7Ah

BACKLIGHT Refer to Chapter 11 (Self-diagnosis status read) TEMPERATURE

SENSOR1/2/3

02h CBh 0: No mean

02h 79h Return value is 2’s

OP code Parameter Remarks

1: NONE 2: AUTO 3: MANUAL

1: NON REVERSE 2: REVERSE

1: COMMON 2: INPUT

| 50(32h): 50sec

1: OFF 2: ON

1: ON 2: OFF

8: Reset

Multi Display Category

Select target FAN. (7Ah)

/7Bh

0: No mean

1: FAN#1 2: FAN#2

3: FAN#3 Read status of target FAN.(7Bh)

0: OFF 1: ON 2: ERROR

complement. (0.5°C step)

DISPL A Y P R OTE CTIO N

COOLING FAN 02h 7Dh 0: No mean

1: AUTO

FAN CONTROL

FAN SPEED 10h 3Fh 0: No mean

2: ON

1: HIGH 2: LOW

Available on X464UN, X554UN, X464UNV, X554UNS

This command is used when REVERSE “MANUAL”.

Momentary

Read Only

a selected sensor. Select sensor (Page02h

OPcode78h) 1 : SENSOR #1 2 : SENSOR #2 3 : SENSOR #3

(37/141)

offset from max.

12(0Ch): Reset External

Item OP

code page

SENSOR1 10h E0h/E1h E0h: Set centigrade

SENSOR2 10h E2h/E3h E2h: Set centigrade

SENSOR3 10h E4h/E5h E4h: Set centigrade

SCREEN SAVER GAMMA 02h DBh 0: No mean

BACKLIGHT 02h DCh 0: No mean

MOTION INTER

VAL

ZOOM 10h 35h 0 : 95%

SIDE BORDER COLOR 02h DFh 0: Black

CHANGE PASSWORD N/A SECURITY Refer to Chapter 22 RESET (DISPLAY PROTECTION)

IP ADDRESS SETTING N/A MAC ADDRESS Refer to Chapter 23 LAN POWER 10h D3h 0: No mean

DDC/CI 10h BEh 0: No mean

PING N/A IP ADDRESS RESET N/A

EXTER N AL C ONT ROL

RESET (EXTERNAL CONTROL)

INPUT DETECT 02h 40h 0: FIRST DETECT

CUSTOM DETECT

PRIORITY1 10h 2Eh 0: No mean

02h DDh 0: OFF(0s)

02h CBh 0: No mean

ADVAN C ED O PTI ON1

OP code Parameter Remarks

0 – 65535(FFFFh) E1h: Set

value

0 – 10(0Ah)

0 – 65535(FFFFh) E3h: Set

value

0 – 10(0Ah)

0 – 65535(FFFFh) E5h: Set

value

0 – 10(0Ah)

1: OFF 2: ON

| 90(5Ah): 900s

| 5 : 100% | 10(0Ah) : 105%

| 100(64h): White

9: Reset Display Protection category

1: OFF 2: ON

Control Category

1: LAST DETECT 2: NONE 3: VIDEO DETECT 4: CUSTOM DETECT

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only)

10s/step

Momentary

(38/141)

and

Item OP

PRIORITY2 10h 2Fh 5: VIDEO

PRIORITY3 10h 30h

LONG CABLE COMP

INPUT CHANGE

TERMINA L SETTING

ON/OFF 10h 3Dh 0: No mean

SOG PEAK 10h 37h 0 – 32(20h) GAIN 10h 38h 0 – 32(20h) R-H. POSITION G-H. POSITION B-H. POSITION SYNC TERMINATION

INPUT CHANGE

INPUT1 10h CEh 0: No mean

INPUT2 10h CFh

DVI MODE 02h CFh 0: No mean

BNC MODE 10h 7Eh 0: No mean

D-SUB MODE 10h 8Eh 0: No mean

SCART MODE 02h 9Eh 0: OFF

OP code Parameter Remarks code page

7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 (SCART) 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 18(12h): HDMI2 128(80h): DPORT3:

1: OFF 2: ON

02h 58h 0 - 7

02h 59h 0 - 7

02h 5Ah 0 - 7

02h E1h 0: No mean

1: HIGH 2: LOW

10h 86h 0: No mean

1: NORMAL 2: QUICK 3: SUPER

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: VIDEO 7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 18(12h): HDMI2 128(80h): DPORT3

1: DVI-PC 2: DVI-HD

1: RGB 2: COMPONENT

1: ON

When you set up "SUPER", please set up INPUT1 INPUT2 first.

(39/141)

10(0Ah): Reset Advanced

ADVAN C ED

Item OP

OP code Parameter Remarks code page

DisplayPort 10h F1h/F2h Select target DPORT.

HDMI SIGNAL 10h 40h 0: No mean

DEINTERLACE 02h 25h 0: No mean

COLOR SYSTEM 02h 21h 0: No mean

OVER SCAN 02h E3h 0: No mean

OPTION

OPTION POWER 10h 41h 0: OFF

SETTING

AUDIO 10h B0h 0: No mean

INTERNAL PC

OFF WARNIN

10h C0h 0: No mean

G AUTO

10h C1h 0: No mean

OFF

START

10h C2h 0: No mean UP PC FORCE

10h C3h 0: No mean QUIT

120Hz 10h 87h 0: No mean

TOUCH

STANDBY 10h C4h 0: No mean

PANEL

PC SOURCE 10h C5h 0: No mean

RESET

02h CBh 0: No mean

(ADVANCED OPTION1)

AUTO

AUTO BRIGHTNESS 02h 2Dh 0: OFF

DIMMING

ROOM LIGHT SENSING 10h C8h 0: No mean

BACKLIGHT

SETTING

MAX LIMIT

10h C9h 0 – 100(64h)

(F1h) 0: No mean

1: DPORT 2: DPORT2 3: DPORT3 Read / Write status of target DPORT.(F2h) 0: No mean 1: 1.1a

2: 1.2

1: EXPAND 2: RAW

1: Off 2: ON

1: NTSC 2: PAL 3: SECAM 4: AUTO 5: 4.43NTSC 6: PAL-60

1: OFF 2: ON

1: ON

1: ANALOG 2: DIGITAL

1: OFF 2: ON

1: Execute

1: ON 2: OFF

1: OFF 2: ON

1: AUTO 2: EXTERNAL PC

Momentary

option1 category

1: ON

1: OFF 2: MODE1 3: MODE2

(40/141)

): Reset Advanced

Item OP

IN BRIGH

T IN DARK

OP code Parameter Remarks code page

10h 33h

0 – 100(64h)

10h 34h 0 – 100(64h)

HUMAN SENSING

SENSI NG LUX

HUMAN SENSING MODE 10h 75h 0: No mean

02h B4h Current Illuminance

read

1: DISABLE 2: AUTO OFF 4: CUSTOM

ON/OFF 10h DDh 0: No mean

1: Off 2: On

BACKLIGHT

BACKL IGHT

10h C6h 0: dark

| 100(64h): light

ON/OFF 10h DEh 0: No mean

1: Off

VOLUME

VOLUME 10h C7h 0: whisper

2: On

| 100(64h): loud

ON/OFF 10h DFh/D0h 0: No mean

1: Off 2: On

INPUT 10h D0h 0: No mean

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: VIDEO

INPUT SELECT

7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 (SCART) 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 18(12h): HDMI2 128(80h): DPORT3

WAITING TIME 10h 78h 30(1Eh): short

| 600(258h): long *1step: 1sec.

INTELLI WIRELESS DATA 10h ECh 0: No mean

1: OFF

2: ON RESET (ADVANCED OPTION2)

02h CBh 0: No mean

11(0Bh

option category FACTORY RESET 02h CBh 0: No mean

1: Factory Reset

Read only

Momentary

(41/141)

supported option

Item OP

OP code Parameter Remarks code page

INPUT 00h 60h 0: No mean

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: VIDEO 7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 (SCART) 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 18(12h): HDMI2 128(80h): DPORT3

AUDIO INPUT 02h 2Eh 0: No mean

1: IN1 2: IN2 3: IN3 4: HDMI 6: OPTION 7: DPORT 8: DPORT2 9: DPORT3 10(0Ah): HDMI2

VOLUME UP/DOWN 00h 62h 0: whisper

| 100(64h): loud

MUTE 00h 8Dh 0: UNMUTE(Set only)

1: MUTE 2: UNMUTE

SCREEN MUTE 10h B6h 0: No mean

1: SCREEN MUTE ON 2: SCREEN MUTE OFF

MTS 02h 2Ch 0: No mean

1: Main 2: Sub 3: Main + Sub

SOUND 02h 34h 0: No mean

1: Off 2: ON

PICTURE MODE 02h 1Ah 0: No mean

1: sRGB 3: HIGHBRIGHT 4: STANDARD 5: CINEMA 8: CUSTOM1 9: CUSTOM2

ASPECT 02h 70h 0: No mean

1: NORMAL 2: FULL 3: WIDE 4: ZOOM 6: DYNAMIC

7: 1:1 (Off/dot by dot)

This operation requires

TV tuner. Same as ‘SURROUND’

sRGB:

PC mode only

CINEMA:

A/V mode only

WIDE: A/V mode only

(42/141)

has limitation of

supported option

Item OP

code page

PIP ON/OFF STILL ON/OFF

PIP INPUT 02h 73h 0: No mean

STILL CAPTURE 02h 76h 0: OFF

SIGNAL INFORMATION 02h EAh 0: No mean

AUTO SETUP 00h 1Eh 0: No mean

TV-CHANNEL UP/DOWN 00h 8Bh 0: No mean

SELECT TEMPERATURE SENSOR 02h 78h 0: No mean

READOUT A TEMPERATURE 02h 79h Returned value is 2's

02h 72h 0: No mean

TEMPE R ATU R E S ENSO R

READOUT CARBON FOOTPRINT (g)

READOUT CARBON FOOTPRINT (kg)

READOUT CARBON USAGE (g)

CARBO N FO O TPR INT

READOUT CARBON USAGE (kg)

10h 10h 0:

10h 11h 0:

10h 26h 0:

10h 27h 0:

OP code Parameter Remarks

1: Off 2: PIP 3: POP 4: STILL 5: PICTUR BY PICTURE

- ASPECT

6: PICTURE BY PICTURE

- FULL

1: VGA 2: RGB/HV 3: DVI 4: HDMI (Set only) 5: VIDEO 7: S-VIDEO 12(0Ch): Y/Pb/Pr 13(0Dh): OPTION 14(0Eh): Y/Pb/Pr2 (SCART) 15(0Fh): DPORT 16(10h): DPORT2 17(11h): HDMI 18(12h): HDMI2 128(80h): DPORT3

1: CAPTURE

1: OFF 2: ON

1: Execute

1: UP 2: DOWN

1: SENSOR #1 2: SENSOR #2 3: SENSOR #3

complement. Refer to section 6.2

999(3E7h):

65535(FFFFh):

999(3E7h):

65535(FFFFh):

This operation

selection. Please refer to the monitor instruction manual.

Momentary

This operation requires

TV tuner.

Read only

(43/141)

7. Power control procedure

7.1 Power status read

1) The controller requests the monitor to reply a current power status.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID from which you want to get status.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message Type is "Command". '0'-'6' (30h, 36h): Message length is 6 bytes.

Message

STX (02h): Start of Message

'0'-'1'-'D'-'6': Get power status command. ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor returns with the current power status.

STX-'0'-'1'-'D'-'6'-ETX BCC CR

Delimiter

Header Message Check

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message Type is "Command reply". '1'-'2' (31h, 32h): Message length is 18 bytes.

Message

STX (02h):Start of Message '0'-'2' (30h, 32h): Reserved data '0'-'0' (30h, 30h): Result code

00: No Error.

01: Unsupported. 'D'-'6'(44h, 36h): Display power mode code '0'-'0' (30h, 30h): Parameter type code is "Set parameter". '0'-'0'-'0'-'4' (30h, 30h, 30h, 34h): Power mode is 4 types. '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Current power mode

ETX (03h): End of Message

STX-'0'-'2'-'0'-'0'-'D'-'6'-'0'-'0'-

'0'-'0'-'0'-'4'-'0'-'0'-'0'-'1'-ETX

0001: ON 0002: Stand-by (power save) 0003: Suspend (power save) 0004: OFF (same as IR power off)

Delimiter

code

BCC CR

(44/141)

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(45/141)

7.2 Power control

1) The controller requests the monitor to control monitor power.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'C'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'C (30h, 43h): Message length is 12 bytes.

Message

STX (02h): Start of Message 'C'-'2'-'0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control command '0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'C'-'2'-'0'-'3'-'D'-'6'-

'0'-'0'-'0'-'1'-ETX

0001: ON 0002, 0003: Do not set. 0004: OFF (same as the power off by IR)

BCC CR

Delimiter

2) The monitor replies a data for confirmation.

Header Message Check code Delimiter

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'E'

Header

SOH (01h): Start of Header

'0' (30h): Reserved

'0' (30h): Message receiver is the controller.

Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". 'N'-'N': Message length

Note.) The maximum data length that can be written to the monitor at a time is 32bytes.

Ex.) The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h).

Message

STX (02h): Start of Message '0'-'0' (30h, 30h): Result code. No error.

'C'-'2’,'0'-'3'-'D'-'6' (43h, 32h, 30h, 33h, 44h, 36h): power control reply command

The monitor replies same as power control command to the controller.

'0'-'0'-'0'-'1' (30h, 30h, 30h, 31h): Power mode

ETX (03h): End of Message

STX-'0'-'0'-'C'-'2'-'0'-'3'-'D'-'6'-

'0'-'0'-'0'-'1'-ETX

0001: ON 0002, 0003: Do not set. 0004: OFF (same as the power off by IR)

BCC CR

(46/141)

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(47/141)

8. Asset Data read and write

MultiSync P403/ P463 /P553 /P703 /P801 /X464UN /X554UN /X464UNV /X554UNS have the area for to store

user’s asset data of up to 64bytes.

8.1 Asset Data Read Request and reply

This command is used in order to read Asset Data.

1) The controller requests the monitor to reply with Asset data.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'A'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID from which you want to get data.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'A' (30h, 41h): Message length is 10 bytes.

Message

STX (02h): Start of Message 'C'-'0'-'0'-'B' (43h, 30h, 30h, 42h): Asset read request command. '0'-'0' (30h, 30h): Offset data from top of the Asset data.

At first set 00h: Read data from the top of Asset data area.

'2'-'0' (32h, 30h): Read out data length is 32bytes.

Secondly set 20h: Read data from the 32bytes offset point in the Asset data area.

Maximum readout length is 32bytes at a time.

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Asset data to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-N-N

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply" N-N: Message length

Note.) This length includes STX and ETX.

Message

STX (02h): Start of Message 'C'-'1'-'0'-'B' (43h, 31h, 30h, 42h): Asset read reply command Data(0) – Data(N): Retuned Asset data

Ex.) When Data(n) is 1234h, replying data is (31h 32h, 33h, 34h).

ETX (03h): End of Message

STX-'C'-'0'-'0'-'B'-

'0'-'0'-'2'-'0'-ETX

BCC CR

STX-'C'-'1'-'0'-'B'-

Data(0)-Data(1)---Data(N)-ETX

Delimiter

BCC CR

Delimiter

(48/141)

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(49/141)

8.2 Asset Data write

This command is used in order to write Asset Data.

1) The controller requests the monitor to write Asset data.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-N-N

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID in which you want to write data.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". N-N: Message length

Note.) The maximum data length that can be written to the monitor at a time is 32bytes.

Message

STX (02h): Start of Message 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data writes command '0'-'0'(30h, 30h): Offset address from top of Asset data.

00h : Write data from top of the Asset data area. Data(0) –- Data(N): Asset data. The data must be ASCII characters strings. ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'C'-'0'-'0'-'E'-'0'-'0'-

Data(0)-Data(1)---Data(N)-ETX

BCC CR

Delimiter

2) The monitor replies a data for confirmation.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-N-N

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". N-N: Message length

Note.) The maximum data length that can be written to the monitor at a time is 32bytes.

Message

STX (02h): Start of Message '0'-'0': Result code. No error. 'C'-'0'-'0'-'E' (43h, 30h, 30h, 45h): Asset Data write command '0'-'0'(30h, 30h): Offset address from top of Asset data.

00h : Write data into from top of the Asset data area.

Data(0) –- Data(N): Asset data. The data must be ASCII characters strings.

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

STX-'0'-'0'-'C'-'0'-'0'-'E'-'0'-'0'-

Data(0)-Data(1)---Data(N)-ETX

Delimiter

BCC CR

(50/141)

CR (0Dh): End of packet

(51/141)

9. Date & Time read and write

9.1 Date & Time Read

This command is used in order to read the setting of Date & Time.

1) The controller requests the monitor to reply with the Date & Time. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to get status.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'6'(30h, 36h): Message length

Message

STX (02h): Start of Message 'C'-'2'-'1'-'1' (43h, 32h, 31h, 31h): Date & time read request command. ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Date & Time to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'4'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller Monitor ID: Indicate a replying Monitor ID

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply" '1'-'4'(31h, 34h): Message length

Message

STX (02h): Start of Message 'C'-'3'-'1'-'1' (43h, 33h, 31h, 31h): Date & Time read reply command 'YY'-'MM'-'DD'-'WW'-'HH'-'MN'-'DS': Date & Time data

YY: Year (offset 2000) '0'-'0'(30h, 30h): 2000 |

'6'-'3'(36h, 33h): 2099 (99 = 63h)

MM: Month

'0'-'1'(30h, 31h): January | '0'-'C'(30h, 43h): December

DD: Day

'0'-'1'(30h, 31h): 1 | '1'-'E'(31h, 45h): 30(=1Eh)

STX-'C'-'2'-'1'-'1'-ETX BCC CR

STX-'C'-'3'-'1'-'1'-

YY-MM-DD-WW-HH-MN-DS-ETX

BCC CR

Delimiter

(52/141)

'1'-'F'(31h, 46h): 31(=1Fh)

WW: weekdays

'0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday

'0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday

HH: Hours

'0'-'0'(30h, 30h): 0 | '1'-'7'(31h, 37h): 23 (=17h)

MN: Minutes

'0'-'0'(30h, 30h): 0 | '3'-'B' (33h, 42h): 59 (=3Bh)

DS: Daylight saving (Summer time)

'0'-'0'(30h, 30h): NO '0'-'1'(30h, 31h): YES

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(53/141)

9.2 Date & Time Write

This command is used in order to write the setting of the Date & Time.

1) The controller requests the monitor to write Date & Time.

Header Message Check code Delimiter

SOH-'0'-Monitor ID-

'0'-'A'-'1'-'2'

STX-'C'-'2'-'1'-'2'-

YY-MM-DD-WW-HH-MN-DS-ETX

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change the setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '1'-'2'(31h, 32h): Message length

Message

STX (02h): Start of Message 'C'-'2'-'1'-'2' (43h, 32h, 31h, 32h): Date & Time write command

'YY'-'MM'-'DD'-'WW'-'HH'-'MN'-'DS': Date & Time data

YY: Year (offset 2000) '0'-'0'(30h, 30h): 2000

'6'-'3'(36h, 33h): 2099 (99 = 63h)

MM: Month

'0'-'1'(30h, 31h): JANUARY | '0'-'C'(30h, 43h): DECEMBER

DD: Day

'0'-'1'(30h, 31h): 1 | '1'-'E'(31h, 45h): 30(=1Eh) '1'-'F'(31h, 46h): 31(=1Fh)

WW: weekdays

'0'-'0'(30h, 30h): SUNDAY '0'-'1'(30h, 31h): MONDAY '0'-'2'(30h, 32h): TUESDAY '0'-'3'(30h, 33h): WEDNESDAY '0'-'4'(30h, 34h): THURSDAY

'0'-'5'(30h, 35h): FRIDAY '0'-'6'(30h, 36h): SATURDAY

HH: Hours

'0'-'0'(30h, 30h): 0 | '1'-'7'(31h, 37h): 23 (=17h)

MN: Minutes

'0'-'0'(30h, 30h): 0 | '3'-'B' (33h, 42h): 59 (=3Bh)

DS: Daylight saving (Summer time)

'0'-'0'(30h, 30h): NO '0'-'1'(30h, 31h): YES

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

(54/141)

Delimiter

CR (0Dh): End of packet

2) The monitor replies a data for confirmation. Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '1'-'6'(31h, 36h): Message length

Message

STX (02h): Start of Message

'C'-'3'-'1'-'2' (43h, 33h, 31h, 32h): Date & Time write reply command ST: Date & Time Status command

'0'-'0'(30h, 30h): No error '0'-'1'(30h, 31h): Error

'YY'-'MM'-'DD'-'WW'-'HH'-'MN'-'DS': Date & Time data

YY: Year (offset 2000) '0'-'0'(30h, 30h): 2000 |

'6'-'3'(36h, 33h): 2099 (99 = 63h)

MM: Month

'0'-'1'(30h, 31h): JANUARY | '0'-'C'(30h, 43h): DECEMBER

DD: Day

'0'-'1'(30h, 31h): 1 | '1'-'E'(31h, 45h): 30(=1Eh) '1'-'F'(31h, 46h): 31(=1Fh)

WW: weekdays

'0'-'0'(30h, 30h): SUNDAY '0'-'1'(30h, 31h): MONDAY '0'-'2'(30h, 32h): TUESDAY '0'-'3'(30h, 33h): WEDNESDAY '0'-'4'(30h, 34h): THURSDAY

'0'-'5'(30h, 35h): FRIDAY '0'-'6'(30h, 36h): SATURDAY

HH: Hours

'0'-'0'(30h, 30h): 0 | '1'-'7'(31h, 37h): 23 (=17h)

MN: Minutes

'0'-'0'(30h, 30h): 0 | '3'-'B' (33h, 42h): 59 (=3Bh)

DS: Daylight saving (Summer time)

'0'-'0'(30h, 30h): NO '0'-'1'(30h, 31h): YES

ETX (03h): End of Message

STX-'C'-'3'-'1'-'2'-ST-

YY-MM-DD-WW-HH-MN-DS-ETX

BCC CR

Delimiter

(55/141)

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(56/141)

10. Schedule read and write

10.1 Schedule Read

This command is used in order to read the setting of the Schedule.

1) The controller requests the monitor to read Schedule. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to get status.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length

Message

STX (02h): Start of Message 'C'-'2'-'2'-'1' (43h, 32h, 32h, 31h): Schedule read request command. PG: Program No.

The data must be ASCII characters strings.

ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Schedule to the controller.

Header Message Check

SOH-'0'-'0'-Monitor ID-

'B'-'2'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '2'-'6'(32h, 36h): Message length

Message

STX (02h): Start of Message 'C'-'3'-'2'-'1' (43h, 33h, 32h, 31h): Schedule read reply command PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P MODEEXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7: Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

ON_HOUR: Turn on time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): ON timer isn't set.

STX-'C'-'2'-'2'-'1'-PG-ETX BCC CR

STX-'C'-'3'-'2'-'1'-PG-ON HOUR-ON MIN-

OFF HOUR-OFF MIN-INPUT-WD-FL-P MODEEXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7-ETX

Delimiter

code

BCC CR

(57/141)

ON_MIN: Turn on time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn't set.

OFF_HOUR: Turn off time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set.

OFF_MIN: Turn off time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(33h, 43h): Off timer isn’t set.

INPUT: Timer input

'0'-'0'(30h,30h): No mean (works on last memory) '0'-'1'(30h,31h): VGA '0'-'2'(30h,32h): RGB/HV '0'-'3'(30h,33h): DVI '0'-'5'(30h,35h): VIDEO '0'-'7'(30h,37h): S-VIDEO '0'-'C'(30h,43h): Y/Pb/Pr '0'-'D'(30h,44h): OPTION '0'-'E'(30h,45h): Y/Pb/Pr2(SCART) '0'-'F'(30h,46h): DPORT '1'-'0'(31h,30h): DPORT2 '1'-'1'(31h,31h): HDMI '1'-'2'(31h,32h): HDMI2 '8'-'0'(38h,30h): DPORT3

WD: Week setting

bit 0: MONDAY bit 1: TUESDAY bit 2: WEDNESDAY bit 3: THURSDAY bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY

EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY

FL: Option

bit 0: 0:once 1:Everyday bit 1: 0:once 1:Every week bit 2: 0:Disable 1:Enable

EX. '0'-'1'(30h, 31h): Disable, Everyday '0'-'4'(30h, 34h): Enable, once

P MODE: Picture mode

'0'-'0'(30h,30h): No mean (works on last memory) '0'-'1'(30h,31h): sRGB '0'-'3'(30h,33h): HIGHBRIGHT '0'-'4'(30h,34h): STANDARD '0'-'5'(30h,34h): CINEMA '0'-'D'(30h,44h): CUSTOM1 '0'-'E'(30h,45h): CUSTOM2

(58/141)

EXT1: Extension1

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT2: Extension 2

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT3: Extension 3

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT4: Extension 4

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT5: Extension 5

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT6: Extension 6

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT7: Extension 7

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(59/141)

***Following command also can be used for to keep backward compatibility, in order to read the setting of the Schedule.

1) The controller requests the monitor to read Schedule. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to get status.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length

Message

STX (02h): Start of Message 'C'-'2'-'1'-'3' (43h, 32h, 31h, 33h): Schedule read request command. PG: Program No.

The data must be ASCII characters strings.

ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Schedule to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '1'-'6'(31h, 36h): Message length

Message

STX (02h): Start of Message 'C'-'3'-'1'-'3' (43h, 33h, 31h, 33h): Schedule read reply command PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL: Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

ON_HOUR: Turn on time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): ON timer isn't set.

Delimiter

STX-'C'-'2'-'1'-'3'-PG-ETX BCC CR

STX-'C'-'3'-'1'-'3'-PG-ON HOUR-ON MIN-

OFF HOUR-OFF MIN-INPUT-WD-FL-ETX

Delimiter

BCC CR

(60/141)

ON_MIN: Turn on time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn't set.

OFF_HOUR: Turn off time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set.

OFF_MIN: Turn off time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(33h, 43h): Off timer isn’t set.

INPUT: Timer input

'0'-'0'(30h, 30h): DVI '0'-'1'(30h, 31h): VGA '0'-'2'(30h, 32h): RGB/HV '0'-'3'(30h, 33h): Y/Pb/Pr '0'-'4'(30h, 34h): VIDEO '0'-'5'(30h, 35h): S-VIDEO '0'-'7'(30h,30h): No mean (Works on last memory)

WD: Week setting

bit 0: MONDAY bit 1: TUESDAY bit 2: WEDNESDAY bit 3: THURSDAY bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY

EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY

FL: Option

bit 0: 0:once 1:Everyday bit 1: 0:once 1:Every week bit 2: 0:Disable 1:Enable

EX. '0'-'1'(30h, 31h): Disable, Everyday '0'-'4'(30h, 34h): Enable, once

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(61/141)

10.2 Schedule Write

This command is used in order to write the setting of the Schedule.

1) The controller requests the monitor to write Schedule.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'2'-'6'

STX-'C'-'2'-'2'-'2'-PG-ON HOUR-ON MIN-

OFF HOUR-OFF MIN-INPUT-WD-FL-P MODE- EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7-ETX

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '2'-'6'(32h, 36h): Message length.

Message

STX (02h): Start of Message 'C'-'2'-'2'-'2' (43h, 32h, 32h, 32h): Schedule writes command

PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P MODE EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7: Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

ON_HOUR: Turn on time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): ON timer isn't set.

ON_MIN: Turn on time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn’t set.

OFF_HOUR: Turn off time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set.

OFF_MIN: Turn off time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(33h, 43h): Off timer isn’t set.

Note: * The same time as ON time and OFF time cannot be set. * Set '1'-'8' to ON/OFF_HOUR and '3'-'C' to ON/OFF_MIN, when ON/OFF time is deleted.

INPUT: Timer input

Delimiter

BCC CR

(62/141)

'0'-'E'(30h,45h): Y/Pb/Pr2(SCART) '0'-'F'(30h,46h): DPORT '1'-'0'(31h,30h): DPORT2 '1'-'1'(31h,31h): HDMI '1'-'2'(31h,32h): HDMI2 '8'-'0'(38h,30h): DPORT3 * Please select active input on your system (setting). * If you select inactive input here, the input change execution will be ignored.

WD: Week setting

bit 0: MONDAY bit 1: TUESDAY bit 2: WEDNESDAY bit 3: THURSDAY bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY

EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY

FL: Option

bit 0: 0:once 1:Everyday bit 1: 0:once 1:Every week bit 2: 0:Disable 1:Enable

* When bit 0 and bit 1 are '1', it behaves as Everyday.

EX. '0'-'1'(30h, 31h): Disable, Everyday '0'-'4'(30h, 34h): Enable, once

P MODE: Picture mode

'0'-'0'(30h,30h): No mean (works on last memory) '0'-'1'(30h,31h): sRGB '0'-'3'(30h,33h): HiGHBRIGHT '0'-'4'(30h,34h): STANDARD '0'-'5'(30h,34h): CINEMA '0'-'D'(30h,44h): CUSTOM1 '0'-'E'(30h,45h): CUSTOM2 * Please select active picture mode on your system (setting). * If you select inactive picture mode here, the input change execution will be ignored.

EXT1: Extension1

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT2: Extension 2

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT3: Extension 3

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT4: Extension 4

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT5: Extension 5

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT6: Extension 6

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT7: Extension 7

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

ETX (03h): End of Message

(63/141)

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies a data for confirmation. Header Message Check

SOH-'0'-'0'-Monitor ID-

'B'-'2'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '2'-'8'(32h, 38h): Message length

Message

STX (02h): Start of Message

'C'-'3'-'2'-'2' (43h, 33h, 32h, 32h): Schedule writes reply command ST: Schedule Status command

'0'-'0'(30h, 30h): No error

'0'-'1'(30h, 31h): Error PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P MODE EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7: Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

ON_HOUR: Turn on time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): ON timer isn't set.

ON_MIN: Turn on time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn’t set.

OFF_HOUR: Turn off time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set.

OFF_MIN: Turn off time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(33h, 43h): Off timer isn’t set.

INPUT: Timer input

'0'-'0'(30h,30h): No mean (works on last memory) '0'-'1'(30h,31h): VGA '0'-'2'(30h,32h): RGB/HV '0'-'3'(30h,33h): DVI '0'-'5'(30h,35h): VIDEO '0'-'7'(30h,37h): S-VIDEO '0'-'C'(30h,43h): Y/Pb/Pr

STX-'C'-'3'-'2'-'2'-ST-PG-ON HOUR-ON MIN-

OFF HOUR-OFF MIN-INPUT-WD-FL-P MODE- EXT1-EXT2-EXT3-EXT4-EXT5-EXT6-EXT7-ETX

Delimiter

code

BCC CR

(64/141)

'0'-'D'(30h,44h): OPTION '0'-'E'(30h,45h): Y/Pb/Pr2(SCART) '0'-'F'(30h,46h): DPORT '1'-'0'(31h,30h): DPORT2 '1'-'1'(31h,31h): HDMI '1'-'2'(31h,32h): HDMI2 '8'-'0'(38h,30h): DPORT3

WD: Week setting

bit 0: MONDAY bit 1: TUESDAY bit 2: WEDNESDAY bit 3: THURSDAY bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY

EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY

FL: Option

bit 0: 0:once 1:Everyday bit 1: 0:once 1:Every week bit 2: 0:Disable 1:Enable

* When bit 0 and bit 1 are '1', it behaves as Everyday.

EX. '0'-'1'(30h, 31h): Disable, Everyday '0'-'4'(30h, 34h): Enable, once

P MODE: Picture mode

EXT1: Extension1

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT2: Extension 2

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT3: Extension 3

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT4: Extension 4

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT5: Extension 5

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT6: Extension 6

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

EXT7: Extension 7

'0'-'0'(30h,30h): (On this monitor, it is always ‘00’)

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

(65/141)

Delimiter

CR (0Dh): End of packet

3) The controller requests the monitor to write Enable/Disable Schedule. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'A'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'A'(30h, 41h): Message length

Message

STX (02h): Start of Message

'C'-'2'-'1'-'5' (43h, 32h, 31h, 35h): Enable/Disable Schedule writes command PG-EN: Enable/Disable Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

EN: Enable /Disable

'0'-'0'(30h, 30h): Disable '0'-'1'(30h, 31h): Enable

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

STX-'C'-'2'-'1'-'5'-PG-EN-ETX BCC CR

Delimiter

CR (0Dh): End of packet

4) The monitor replies a data for confirmation. Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'C'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '0'-'C' (30h, 43h): Message length

Message

STX (02h): Start of Message

'C'-'3'-'1'-'5' (43h, 33h, 31h, 35h): Enable/Disable Schedule writes reply command ST: Enable/Disable Schedule Status command

'0'-'0'(30h, 30h): No error '0'-'1'(30h, 31h): Error

PG-EN: Enable/Disable Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

EN: Enable /Disable

'0'-'0'(30h, 30h): Disable

STX-'C'-'3'-'1'-'5'-ST-PG-EN-ETX BCC CR

Delimiter

(66/141)

'0'-'1'(30h, 31h): Enable

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(67/141)

***Following command also can be used for to keep backward compatibility, in order to write the setting of the Schedule.

1) The controller requests the monitor to write Schedule.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'1'-'6'

STX-'C'-'2'-'1'-'4'-PG-ON HOUR-ON MIN-

OFF HOUR-OFF MIN-INPUT-WD-FL-ETX

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '1'-'6'(31h, 36h): Message length.

Message

STX (02h): Start of Message 'C'-'2'-'1'-'4' (43h, 32h, 31h, 34h): Schedule writes command

PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL: Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

ON_HOUR: Turn on time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): ON timer isn't set.

ON_MIN: Turn on time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn’t set.

OFF_HOUR: Turn off time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set.

OFF_MIN: Turn off time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(33h, 43h): Off timer isn’t set.

INPUT: Timer input

'0'-'0'(30h, 30h): DVI '0'-'1'(30h, 31h): VGA '0'-'2'(30h, 32h): RGB/HV '0'-'3'(30h, 33h): Y/Pb/Pr '0'-'4'(30h, 34h): VIDEO '0'-'5'(30h, 35h): S-VIDEO '0'-'7'(30h, 37h): (Works on last memory) * Please select active input on your system (setting). * If you select inactive input here, the input change execution will be ignored.

WD: Week setting

bit 0: MONDAY bit 1: TUESDAY

Delimiter

(68/141)

bit 2: WEDNESDAY bit 3: THURSDAY bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY

EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY

FL: Option

bit 0: 0:once 1:Everyday bit 1: 0:once 1:Every week bit 2: 0:Disable 1:Enable

* When bit 0 and bit 1 are '1', it behaves as Everyday.

EX. '0'-'1'(30h, 31h): Disable, Everyday '0'-'4'(30h, 34h): Enable, once

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies a data for confirmation. Header Message Check

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '1'-'8'(31h, 38h): Message length

Message

STX (02h): Start of Message

'C'-'3'-'1'-'4' (43h, 33h, 31h, 34h): Schedule writes reply command ST: Schedule Status command

'0'-'0'(30h, 30h): No error '0'-'1'(30h, 31h): Error

PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL: Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

ON_HOUR: Turn on time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): ON timer isn't set.

ON_MIN: Turn on time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59

STX-'C'-'3'-'1'-'4'-ST-PG-ON HOUR-ON MIN-

OFF HOUR-OFF MIN-INPUT-WD-FL-ETX

Delimiter

code

BCC CR

(69/141)

'3'-'C'(33h, 43h): On timer isn’t set.

OFF_HOUR: Turn off time (hour)

'0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set.

OFF_MIN: Turn off time (minute)

'0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(33h, 43h): Off timer isn’t set.

INPUT: Timer input

'0'-'0'(30h, 30h): DVI '0'-'1'(30h, 31h): VGA '0'-'2'(30h, 32h): RGB/HV '0'-'3'(30h, 33h): Y/Pb/Pr '0'-'4'(30h, 34h): VIDEO '0'-'5'(30h, 35h): S-VIDEO '0'-'7'(30h,30h): No mean (Works on last memory)

WD: Week setting

bit 0: MONDAY bit 1: TUESDAY bit 2: WEDNESDAY bit 3: THURSDAY bit 4: FRIDAY bit 5: SATURDAY bit 6: SUNDAY

EX. '0'-'1'(30h, 31h): MONDAY '0'-'4'(30h, 34h): TUESDAY '0'-'F'(30h, 46h): MONDAY, TUESDAY, WEDNESDAY and THURSDAY '7'-'F'(37h, 46h): MONDAY to SUNDAY

FL: Option

bit 0: 0:once 1:Everyday bit 1: 0:once 1:Every week bit 2: 0:Disable 1:Enable

* When bit 0 and bit 1 are '1', it behaves as Everyday.

EX. '0'-'1'(30h, 31h): Disable, Everyday '0'-'4'(30h, 34h): Enable, once

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

3) The controller requests the monitor to write Enable/Disable Schedule. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'A'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'.

'0' (30h): Message sender is the controller.

STX-'C'-'2'-'1'-'5'-PG-EN-ETX BCC CR

Delimiter

(70/141)

'A' (41h): Message type is "Command". '0'-'A'(30h, 41h): Message length

Message

STX (02h): Start of Message

'C'-'2'-'1'-'5' (43h, 32h, 31h, 35h): Enable/Disable Schedule writes command PG-EN: Enable/Disable Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

EN: Enable /Disable

'0'-'0'(30h, 30h): Disable '0'-'1'(30h, 31h): Enable

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

4) The monitor replies a data for confirmation.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'C'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '0'-'C' (30h, 43h): Message length

Message

STX (02h): Start of Message

'C'-'3'-'1'-'5' (43h, 33h, 31h, 35h): Enable/Disable Schedule writes reply command ST: Enable/Disable Schedule Status command

'0'-'0'(30h, 30h): No error '0'-'1'(30h, 31h): Error

PG-EN: Enable/Disable Schedule data

PG: Program No.

'0'-'0'(30h, 30h): Program No.1 | '0'-'6'(30h, 36h): Program No.7

EN: Enable /Disable

'0'-'0'(30h, 30h): Disable '0'-'1'(30h, 31h): Enable

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

STX-'C'-'3'-'1'-'5'-ST-PG-EN-ETX BCC CR

Delimiter

CR (0Dh): End of packet

Delimiter

(71/141)

11. Self diagnosis

11.1 Self-diagnosis status read

This command is used in order to read the Self-diagnosis status.

1) The controller requests the monitor to read Self-diagnosis status. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'4'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get status.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'4'(30h, 34h): Message length

Message

STX (02h): Start of Message

'B'-'1' (42h, 31h): Self-diagnosis command ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'B'-'1'-ETX BCC CR

Delimiter

2) The monitor replies a result of the self-diagnosis.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-N-N

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". N-N: Message length

Note.) The maximum data length that can be written to the monitor at a time is 32bytes.

Ex.) The byte data 20h is encoded as ASCII characters '2' and '0' (34h and 30h).

Message

STX (02h): Start of Message

'A'-'1' (41h, 31h): Application Test Report reply command ST: Result of self-tests

'0'-'0'(30h, 30h):00: Normal '7'-'0'(37h, 30h):70: Standby-power +3.3V abnormality '7'-'1'(37h, 31h):71: Standby-power +5V abnormality '7'-'2'(37h, 32h):72: Panel-power +12V abnormality '7'-'8'(37h, 38h):78: Inverter power/Option slot2 power +24V Abnormality '8'-'0'(38h, 30h):80: Cooling fan-1 abnormality '8'-'1'(38h, 31h):81: Cooling fan-2 abnormality ('8'-'2'(38h, 32h):82: Cooling fan-3 abnormality) '9'-'1'(39h, 31h):91: LED Backlight abnormality 'A'-'0'(41h, 30h):A0: Temperature abnormality – shutdown 'A'-'1'(41h, 31h):A1: Temperature abnormality – half brightness 'A'-'2'(41h, 32h):A2: SENSOR reached at the temperature that the user had specified. 'B'-'0'(42h, 30h):B0: No signal

STX-'A'-'1'-

ST(0)-ST(1) --------ST(n)-ETX

Delimiter

BCC CR

(72/141)

'D'-'0'(44h, 30h):D0: PROOF OF PLAY buffer reduction 'E'-'0'(45h, 30h):E0: System error

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(73/141)

12. Serial No. & Model Name Read

12.1 Serial No. Read

This command is used in order to read a serial number.

1) The controller requests the monitor to read a serial number. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get serial number.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'6'(30h, 36h): Message length

Message

STX (02h): Start of Message

'C'-'2'-'1'-'6' (43h, 32h, 31h, 36h): Serial No. command

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'C'-'2'-'1'-'6'-ETX BCC CR

Delimiter

2) The monitor replies the serial No. data to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-N-N

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'.

'B' (42h): Message type is "Command reply". N-N: Message length

Note.) The maximum data length that can be returned from the monitor at a time is

32bytes.

Ex.) The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h).

Message

STX (02h): Start of Message

'C'-'3'-'1'-'6' (41h, 33h, 31h, 36h): Serial No. reply command Data(0)-Data(1)----Data(n):Serial Number

The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h). Ex.) Foe example when receiveing Serial Number data 33h 31h 33h 32h 33h 33h 33h 34h

Step1: Serial Number data is encoded as character string.

Example:

33h 31h 33h 32h 33h 33h 33h 34h -> '3','1','3','2','3','3','3','4'

Step2: Decode pairs of ASCII characters to hexadecimal values.

Example:

'3','1','3','2','3','3','3','4' -> 31h 32h 33h 34h

Step3: Byte data represents the ASCII string data.

Example:

31h 32h 33h 34h -> "1234"

Result: Serial Number is "1234".

STX-'C'-'3'-'1'-'6'-

Data(0)-Data(1)---Data(n)-ETX

Delimiter

BCC CR

(74/141)

Note: No null termination character is sent.

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(75/141)

12.2 Model Name Read

This command is used in order to read the Model Name.

1) The controller requests the monitor to read Model Name. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get Model Name.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'6'(30h, 36h): Message length

Message

STX (02h): Start of Message

'C'-'2'-'1'-'7' (43h, 32h, 31h, 37h): Model Name command

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

STX-'C'-'2'-'1'-'7'-ETX BCC CR

Delimiter

CR (0Dh): End of packet

2) The monitor replies the model name data to the controller. Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-N-N

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". N-N: Message length

Note.) The maximum data length that can be returned from the monitor at a time is

32bytes.

Ex.) The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h).

Message

STX (02h): Start of Message

'C'-'3'-'1'-'7' (43h, 33h, 31h, 37h): Model Name reply Command Data(0) -Data(1)----Data(n):Model name

The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h). Ex.) Foe example when receiving Model Name data 35h 30h 33h 34h 33h 30h 33h 33h

Step1: Model Name data is encoded character string.

Example:

35h 30h 33h 34h 33h 30h 33h 33h -> '5','0','3','4','3','0','3','3'

Step2: Decode pairs of ASCII characters to hexadecimal values.

Example:

'5','0','3','4','3','0','3','3' -> 50h 34h 30h 33h

Step3: Byte data represents the ASCII string data.

Example:

50h 34h 30h 33h -> "P403" Result: Model Name is "P403". Note: No null termination character is sent.

ETX (03h): End of Message

Check code

BCC: Block Check Code

STX-'C'-'3'-'1'-'7'-

Data(0) -Data(1)—----Data(n)-ETX

Delimiter

BCC CR

(76/141)

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(77/141)

13. Security Lock

13.1 Security Lock Control

This command sets the condition of security lock function to "LOCK" or "UNLOCK".

If security pass codes 1st to 4th are matched with monitor resisted pass codes, then this command is executed, and reply no error status and a new condition. If codes aren't matched with them then setting isn't changed, and reply error status and a current condition. If the monitor receives this command while waiting for Pass codes inputs, then it only checks Pass cords (and releases image muting if Pass codes are OK) and doesn't apply "EN" parameter.

1) The controller requests the monitor to set the condition of security lock. Header Message Check code

SOH-'0'-MonitorID-

'0'-'A'-'1'-'0'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '1'-'0'(31h, 30h): Message length

Message

STX (02h): Start of Message 'C'-'2'-'1'-'D' (43h, 32h, 31h, 44h): Security Lock Control command EN-P1-P2-P3-P4: Lock condition control data

EN: Enable /Disable

'0'-'0'(30h, 30h): Disable '0'-'1'(30h, 31h): Enable

P1: Security Pass code 1st

'0'-'0'(30h, 30h): "0" | '0'-'9'(30h, 39h): "9"

P2: Security Pass code 2nd

'0'-'0'(30h, 30h): "0" | '0'-'9'(30h, 39h): "9"

P3: Security Pass code 3rd

'0'-'0'(30h, 30h): "0" | '0'-'9'(30h, 39h): "9"

P4: Security Pass code 4th

'0'-'0'(30h, 30h): "0" | '0'-'9'(30h, 39h): "9"

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'C'-'2'-'1'-'D'-

EN-P1-P2-P3-P4-ETX

Delimiter

BCC CR

(78/141)

2) The monitor replies the result to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'3'-'1'-'D'-

ST-EN-ETX

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '0'-'A'(30h, 41h): Message length

Message

STX (02h): Start of Message 'C'-'3'-'1'-'D' (43h, 33h, 31h, 44h): Security Lock Control reply command ST-EN: Lock condition result data

ST: Status

'0'-'0'(30h, 30h): No error '0'-'1'(30h, 31h): Error

EN: Enable /Disable (Current condition)

'0'-'0'(30h, 30h): Disable '0'-'1'(30h, 31h): Enable

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Delimiter

(79/141)

14. Direct TV Chanel Read & Write

When DTV unit (Option unit) is installed, channel settings is read and write directly.

14.1 Direct TV Chanel Read & Reply

1) The controller requests the monitor to read channel information. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'6'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get Model Name.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'6'(30h, 36h): Message length

Message

STX (02h): Start of Message

'C'-'2'-'2'-'C' (43h, 32h, 32h, 43h): Direct TV Channel Read command

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

STX-'C'-'2'-'2'-'C'-ETX BCC CR

Delimiter CR (0Dh): End of packet

2) The monitor replies the result to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'2'

STX-'C'-'3'-'2'-'C'-

MajorCH-MinorCH-ETX

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '1'-'2'(31h, 32h): Message length = 18bytes

Message

STX (02h): Start of Message 'C'-'3'-'2'-'C' (43h, 33h, 32h, 43h): Direct TV Channel read reply command MajorCH: Major Channel (00000000h – FFFFFFFFh),

'0'-'0'-'0'-'0'-'0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F'-'F'-'F'-'F'-'F'

MinorCH: Minor Channel (0000h – FFFFh),

'0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F'

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Delimiter

(80/141)

14.2 Direct TV Chanel Write & Reply

1) The controller requests the monitor to write channel information. Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID which you want to get Model Name.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '1'-'2'(31h, 32h): Message length = 18bytes

Message

STX (02h): Start of Message

'C'-'2'-'2'-'D' (43h, 32h, 32h, 44h): Direct TV Channel write command

MajorCH: Major Channel (00000000h – FFFFFFFFh),

'0'-'0'-'0'-'0'-'0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F'-'F'-'F'-'F'-'F'

MinorCH: Minor Channel (0000h – FFFFh),

'0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F'

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

STX-'C'-'2'-'2'-'D'-

Delimiter

BCC CR

MajorCH-MinorCH-ETX

Delimiter CR (0Dh): End of packet

2) The monitor replies the result to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'1'-'2'

STX-'C'-'3'-'2'-'D'-

MajorCH-MinorCH-ETX

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to 'A', the replying Monitor ID is '1'. 'B' (42h): Message type is "Command reply". '1'-'2'(31h, 32h): Message length = 18bytes

Message

STX (02h): Start of Message 'C'-'3'-'2'-'D' (43h, 33h, 32h, 43h): Direct TV Channel write reply command MajorCH: Major Channel (00000000h – FFFFFFFFh),

'0'-'0'-'0'-'0'-'0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F'-'F'-'F'-'F'-'F'

MinorCH: Minor Channel (0000h – FFFFh),

'0'-'0'-'0'-'0' - 'F'-'F'-'F'-'F'

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Delimiter

(81/141)

15. Daylight Saving read & write

15.1 Daylight Saving Read

This command is used in order to read the setting of Daylight Saving.

1) The controller requests the monitor to reply a Daylight Saving setting.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length (8bytes)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'1' (43h, 41h, 30h, 31h): Daylight Saving Command '0'-'0' (30h. 30h): Read ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Date & Time to the controller.

Header Message Check

SOH-'0'-'0'-Monitor ID-

'B'-'2'-'0'

STX-'C'-'A'-'0'-'1'-'0'-'0'-ETX BCC CR

STX-'C'-'B'-'0'-'1'-'0'-'0'-ST-BM-BD1-BD

-BT1-BT2-EM-ED1-ED2-ET1-ET2-TD-ETX

Delimiter

code

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '2'-'0'(32h, 30h): Message length (32bytes)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'1' (43h, 42h, 30h, 31h): Daylight Saving Setting reply command '0'-'0' (30h, 30h): Read ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) BM: BEGIN MONTH JANUARY – DECEMBER: 01h (30h, 31h) - 12h (31h, 32h) BD1: BEGIN DAY1 FIRST : 01h (30h, 31h) SECOND : 02h (30h, 32h) THIRD : 03h (30h, 33h) FOUR : 04h (30h, 34h)

(82/141)

LAST : 05h (30h, 35h) BD2: BEGIN DAY2 (Day of the week) SUNDAY : 01h (30h, 31h) MONDAY : 02h (30h, 32h) TUESDAY : 03h (30h, 33h) WEDNESDAY : 04h (30h, 34h) THURSDAY : 05h (30h, 35h) FRIDAY : 06h (30h, 36h) SATURDAY : 07h (30h, 37h) BT1: BEGIN TIME1 (Hour) 00h (30h, 30h) – 23 (32h, 33h) BT2: BEGIN TIME2 (Minute) 00h (30h, 30h) – 59 (35h, 39h) EM: END MONTH JANUARY – DECEMBER: 01h (30h, 31h) - 12h (31h, 32h) ED1: END DAY1 FIRST : 01h (30h, 31h) SECOND : 02h (30h, 32h) THIRD : 03h (30h, 33h) FOUR : 04h (30h, 34h) LAST : 05h (30h, 35h) ED2: END DAY2 (Day of the week) SUNDAY : 01h (30h, 31h) MONDAY : 02h (30h, 32h) TUESDAY : 03h (30h, 33h) WEDNESDAY : 04h (30h, 34h) THURSDAY : 05h (30h, 35h) FRIDAY : 06h (30h, 36h) SATURDAY : 07h (30h, 37h) ET1: END TIME1 (Hour) 00h (30h, 30h) – 23 (32h, 33h) ET2: END TIME2 (Minute) 00h (30h, 30h) – 59 (35h, 39h) TD: TIME DIFFERENCE +01:00 : 00h (30h, 30h) +00:30 : 01h (30h, 31h)

-00:30 : 02h (30h, 32h)

-01:00 : 03h (30h, 33h) ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(83/141)

15.2 Daylight Saving Write

This command is used in order to write the setting of the Daylight Saving.

1) The controller requests the monitor to write Daylight Saving.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'1'-'E'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '1'-'E'(31h, 45h): Message length (30bytes)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'1' (43h, 41h, 30h, 31h): Daylight Saving Setting Command '0'-'1' (30h, 31h): Write BM: BEGIN MONTH JANUARY – DECEMBER: 01h (30h, 31h) - 12h (31h, 32h) BD1: BEGIN DAY1 FIRST : 01h (30h, 31h) SECOND : 02h (30h, 32h) THIRD : 03h (30h, 33h) FOUR : 04h (30h, 34h) LAST : 05h (30h, 35h) BD2: BEGIN DAY2 (Day of the week) SUNDAY : 01h (30h, 31h) MONDAY : 02h (30h, 32h) TUESDAY : 03h (30h, 33h) WEDNESDAY : 04h (30h, 34h) THURSDAY : 05h (30h, 35h) FRIDAY : 06h (30h, 36h) SATURDAY : 07h (30h, 37h) BT1: BEGIN TIME1 (Hour) 00h (30h, 30h) – 23 (32h, 33h) BT2: BEGIN TIME2 (Minute) 00h (30h, 30h) – 59 (35h, 39h) EM: END MONTH JANUARY – DECEMBER: 01h (30h, 31h) - 12h (31h, 32h) ED1: END DAY1 FIRST : 01h (30h, 31h) SECOND : 02h (30h, 32h) THIRD : 03h (30h, 33h) FOUR : 04h (30h, 34h) LAST : 05h (30h, 35h) ED2: END DAY2 (Day of the week) SUNDAY : 01h (30h, 31h) MONDAY : 02h (30h, 32h) TUESDAY : 03h (30h, 33h) WEDNESDAY : 04h (30h, 34h) THURSDAY : 05h (30h, 35h) FRIDAY : 06h (30h, 36h) SATURDAY : 07h (30h, 37h) ET1: END TIME1 (Hour) 00h (30h, 30h) – 23 (32h, 33h) ET2: END TIME2 (Minute) 00h (30h, 30h) – 59 (35h, 39h) TD: TIME DIFFERENCE

STX-'C'-'A'-'0'-'1'-'0'-'1'-BM-BD1-BD2-

BT1-BT2-EM-ED1-ED2-ET1-ET2-TD-ETX

BCC CR

Delimiter

(84/141)

+01:00 : 00h (30h, 30h) +00:30 : 01h (30h, 31h)

-00:30 : 02h (30h, 32h)

-01:00 : 03h (30h, 33h) ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies a written in result. Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h, 41h): Message length (10bytes)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'1' (43h, 42h, 30h, 31h): Daylight Saving Setting Command '0'-'1' (30h, 31h): Write ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message

STX-'C'-'B'-'0'-'1'-'0'-'1'-ST-ETX BCC CR

Delimiter

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(85/141)

16. Firmware Version

16.1 Firmware Version Read

This command is used in order to read a firmware version.

1) The controller requests the monitor to reply a firmware version.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length (8bytes)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'2' (43h, 41h, 30h, 32h): Firmware Version Command TY: Firmware Type Firmware1 : 00h (30h, 30h) Firmware2 : 01h (30h, 31h) Firmware3 : 02h (30h, 32h) Firmware4 : 03h (30h, 33h) ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

STX-'C'-'A'-'0'-'2'-TY-ETX BCC CR

Delimiter

2) The monitor replies a firmware version to the controller.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'B'-'1'-'1'

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '1'-'1'(31h, 31h): Message length (17bytes)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'2' (43h, 42h, 30h, 32h): Firmware Version Read reply ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) TY: Firmware Type Firmware1 : 00h (30h, 30h) Firmware2 : 01h (30h, 31h) MV: Major Version:

STX-'C'-B'-'0'-'2'-ST-TY-MV-

PP-BV1-BV2-BV3-BR1-BR2-ETX

BCC CR

Delimiter

(86/141)

00h (30h, 30h) – 09h (30h, 39h) PP: Period:

2Eh (32h, 45h) (fixed) BV1: Minor (Basic) Version1:

00h (30h, 30h) – 09h (30h, 39h) BV2: Minor (Basic) Version2:

00h (30h, 30h) – 09h (30h, 39h) BV3: Minor (Basic) Version3:

00h (30h, 30h) – 09h (30h, 39h) BR1: Branch Version1:

A:41h (34h, 31h) – Z:5Ah (35h, 41h) BR2: Branch Version1:

A:41h (34h, 31h) – Z:5Ah (35h, 41h)

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(87/141)

17. Auto ID

17.1 Auto ID Execute

This command is used in order to execute Auto ID function.

1) The controller requests the monitor to execute Auto ID function.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length (8byte)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'A' (43h, 41h, 30h, 41h, 30h, 31h): Auto ID Command '0'-'1' (30h, 30h): Execute ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies receipt result.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'A'-'0'-'A'-'0'-'1'-ETX BCC CR

STX-'C'-'B'-'0'-'A'-'0'-'1'-ST-ETX BCC CR

Delimiter

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h,41h): Message length (10byte)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'A' (43h, 42h, 30h, 41h, 30h, 31h): Auto ID Reply Command '0'-'1' (30h, 30h): Execute ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

(88/141)

Delimiter

CR (0Dh): End of packet

(89/141)

17.2 Auto ID Complete

This command is used in order to notify complete status of Auto ID.

1) The monitor sends the controller to complete status of Auto ID.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'C'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'C'(30h,43h): Message length (12byte)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'A'-'0'-'2' (43h, 41h, 30h, 41h, 30h, 32h): Auto ID '0'-'2' (30h,32h): Complete ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) MON: DETECTED MONITORS 01h (30h, 31h) - 64h (36h, 34h) ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The controller replies to the monitor.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'A'-'0'-'A'-'0'-'2'-ST-MON-ETX BCC CR

STX-'C'-'B'-'0'-'A'-'0'-'2'-ST-ETX BCC CR

Delimiter

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h,41h): Message length (10byte)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'A' (43h, 42h, 30h, 41h): Auto ID Reply Command '0'-'2' (30h,32h): Complete ST : Error Status No Error : 00h (30h, 30h) *Fixed ETX (03h): End of Message

(90/141)

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(91/141)

17.3 Auto ID Reset

This command is used in order to reset Auto ID.

1) The controller requests the monitor to reset Auto ID.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length (8byte)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'A' (43h, 41h, 30h, 41h): Auto ID Command '0'-'3' (30h, 33h): Reset ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies to the controller.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'A'-'0'-'A'-'0'-'3'-ETX BCC CR

STX-'C'-'B'-'0'-'A'-'0'-'3'-ST-ETX BCC CR

Delimiter

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h,41h): Message length (10byte)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'A' (43h, 42h, 30h, 41h): Auto ID Reply '0'-'3' (30h, 33h): Reset ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(92/141)

18. Input Name

18.1 Input Name Read

This command is used in order to read the setting of Input Name.

1) The controller requests the monitor to reply Input Name setting.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length (8bytes)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'4' (43h, 41h, 30h, 34h): Input Name Command '0'-'0' (30h. 30h): Read ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies Input Name to the controller.

Header Message Check

SOH-'0'-'0'-Monitor ID-

'B'-LN(H)-LN(L)

STX-'C'-'A'-'0'-'4'-'0'-'0'-ETX BCC CR

STX-'C'-'B'-'0'-'4'-'0'-'0'-

Data(0)-Data(1)-Data(2)- --- -Data(n)-ETX

Delimiter

code

BCC CR

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". LN(H)-LN(L): Message length (byte length), from STX to ETX

Ex.) The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h).

Message

STX (02h): Start of Message 'C'-'B'-'0'-'4' (43h, 42h, 30h, 34h): Input Name command reply '0'-'0' (30h, 30h): Read Data(n) : Input name *n = Max 14

The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h). Ex.) For example when receiving Data(n) of 35h 36h 34h 37h 34h 31h

Step1: Input Name data is encoded as character code.

Example:

35h 36h 34h 37h 34h 31h -> '5'-'6'-'4'-'7'-'4'-'1'

Step2: Decode pairs of ASCII characters to hexadecimal values.

Example:

'5'-'6'-'4'-'7'-'4'-'1' -> 56h 47h 41h

Step3: Byte data represents the ASCII string data.

(93/141)

Result: Input Name is “VGA”. Note: No null termination character is sent.

ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

Example:

56h 47h 41h -> “VGA”

(94/141)

18.2 Input Name Write

This command is used in order to write the setting of Input Name.

1) The controller requests the monitor to write Input Name.

Header Message Check

SOH-'0'-Monitor ID-

'0'-'A'- LN(H)-LN(L)

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". LN(H)-LN(L): Message length (byte length), from STX to ETX

Ex.) The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h).

Message

STX (02h): Start of Message 'C'-'A'-'0'-'4' (43h, 41h, 30h, 34h): Input name Command '0'-'1' (30h, 31h): Write Data(n) : Input name *n = Max 14

The byte data 20h is encoded as ASCII characters '2' and '0' (32h and 30h). Ex.) In the case of Input Name "VGA"

Step1: Input Name data is handled as character code.

Example:

"VGA" -> 56h 47h 41h (ASCII)

Step2: The hexadecimal value of each original character is encoded as two ASCII

characters representing the value.

Example:

56h 47h 41h -> '5'-'6'-'4'-'7'-'4'-'1'

Result: The following data is assigned to Data(n).

35h 36h 34h 37h 34h 31h

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies a written in result. Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'A'-'0'-'4'-'0'-1'-

Data(0)-Data(1)-Data(2)- --- -Data(n)-ETX

STX-'C'-'B'-'0'-'0'-'0'-'1'-ST-ETX BCC CR

Delimiter

code

BCC CR

Delimiter

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h, 41h): Message length (10bytes)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'4' (43h, 42h, 30h, 34h): Input name Command '0'-'1' (30h, 31h): Write

(95/141)

ST: Status 00h (30h, 30h): No Error 01h (30h, 31h): Error ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(96/141)

18.3 Input Name Reset

This command is used in order to reset the Input Name.

1) The controller requests the monitor to reset Input Name.

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'0'-'8'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '0'-'8'(30h, 38h): Message length (8bytes)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'4' (43h, 41h, 30h, 34h): Input Name Command '0'-'2' (30h. 32h): Reset ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies result. Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'A'-'0'-'4'-'0'-'2'-ETX BCC CR

STX-'C'-'B'-'0'-'0'-'0'-'2'-ST-ETX BCC CR

Delimiter

Header

SOH (01h): Start of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h, 41h): Message length (10bytes)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'4' (43h, 42h, 30h, 34h): Input name Command '0'-'2' (30h, 32h): Reset ST: Status 00h (30h, 30h): No Error 01h (30h, 31h): Error ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

(97/141)

Delimiter

CR (0Dh): End of packet

(98/141)

19. Auto Tile Matrix

19.1 Auto Tile Matrix Execute

This command is used in order to activate the Auto Tile Matrix Setup.

1) The controller requests the monitor to execute Auto Tile Matrix

Header Message Check code

SOH-'0'-Monitor ID-

'0'-'A'-'1'-'2'

Header

SOH (01h): Start of Header '0' (30h): Reserved Monitor ID: Specify the Monitor ID of which you want to change a setting.

Ex.) If Monitor ID is '1', specify 'A'. '0' (30h): Message sender is the controller. 'A' (41h): Message type is "Command". '1'-'2'(31h, 32h): Message length (18bytes)

Message

STX (02h): Start of Message 'C'-'A'-'0'-'3' (43h, 41h, 30h, 33h): Auto Tile Matrix Command '0'-'1' (30h, 31h): Execution HM: HORIZONTAL MONITORS 01h (30h, 31h) - 10h (31h, 30h) VM: VERTICAL MONITORS 01h (30h, 31h) - 10h (31h, 30h) PID: PETTERN ID 01h (30h, 31h) *Fixed SEL: CURRENT INPUT SELECT VGA : 01h (30h, 31h) DVI : 03h (30h, 33h) VIDEO : 05h (30h, 35h) S-VIDEO : 07h (30h, 37h) Y/Pb/Pr : 0Ch (30h, 43h) OPTION : 0Dh (30h, 44h) Y/Pb/Pr2 : 0Eh (30h, 45h) DPORT : 0Fh (30h, 46h) DPORT2 : 10h (31h, 30h) HDMI : 11h (31h, 31h) HDMI2 : 12h (31h, 32h) DPORT3 : 80h (38h, 30h) TMEM: TILE MATRIX MEM COMMON : 00h (30h, 30h)

INPUT : 01h (30h, 31h)

ETX (03h): End of Message

Check code

BCC: Block Check Code Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

2) The monitor replies receipt result.

Header Message Check code

SOH-'0'-'0'-Monitor ID-

'B'-'0'-'A'

STX-'C'-'A'-'0'-'3'-'0'-'1'-

HM-VM-PID-SEL-TMEM-ETX

STX-'C'-'B'-'0'-'3'-'0'-'1'-ST-ETX BCC CR

BCC CR

Delimiter

Header

SOH (01h): Start of Header '0' (30h): Reserved

(99/141)

'0' (30h): Message receiver is the controller. Monitor ID: Indicate a replying Monitor ID.

Ex.) When this byte is set to ‘A’, replying monitor’s ID is ‘1’. 'B' (42h): Message type is "Command reply". '0'-'A'(30h, 41h): Message length (10bytes)

Message

STX (02h): Start of Message 'C'-'B'-'0'-'3' (43h, 42h, 30h, 33h): Auto Tile Matrix Command '0'-'1' (30h, 31h): Execution ST: Error Status No Error : 00h (30h, 30h) Error : 01h (30h, 31h) ETX (03h): End of Message

Check code

BCC: Block Check Code

Refer to the section 4.3 “Check code” for a BCC calculation.

Delimiter

CR (0Dh): End of packet

(100/141)

NEC X554UN, X464UNV-2, X464UN, P703-PC, P703 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual