— i —
Important Information .......................................................................................................... iii
1 Getting Started .................................................................................................................. 1
1-1 Packing Checklist ........................................................................................................................ 1
1-2 Views of Projector Parts ............................................................................................................... 2
Front-right View .......................................................................................................................... 2
Top view ..................................................................................................................................... 3
Rear view-On-screen Display (OSD) buttons .................................................................................. 4
Rear view (Terminal Panel) ........................................................................................................... 5
Bottom view ............................................................................................................................... 6
Reference drawings for stand ....................................................................................................... 7
1-3 Remote Control Specification ...................................................................................................... 8
1-4 Remote Control Operating Range .............................................................................................. 10
1-5 Projector and Remote Control Buttons ....................................................................................... 10
2 Setup and Operation ........................................................................................................ 11
2-1 Inserting the Remote Control Batteries ....................................................................................... 11
2-2 Starting and Shutting down the Projector .................................................................................. 12
2-3 Adjusting the Projector Level ..................................................................................................... 14
2-4 Adjusting Projected Image Position Using Lens Shift ................................................................... 15
Adjusting the vertical image position ......................................................................................... 16
Adjusting the horizontal image position ..................................................................................... 16
2-5 Adjusting the Zoom, Focus and Keystone ................................................................................... 17
2-6 Adjusting the Volume ................................................................................................................ 18
3 On-Screen Display (OSD) Menu Settings .......................................................................... 19
3-1 OSD Menu Controls ................................................................................................................... 19
Navigating the OSD ................................................................................................................... 19
3-2 Setting the OSD Language ......................................................................................................... 20
3-3 OSD Menu Overview ................................................................................................................. 21
3-4 INPUT Menu .............................................................................................................................. 23
COMPUTER Menu ...................................................................................................................... 24
3D Setting ................................................................................................................................ 25
3-5 ADJUST Menu ................................................................................................ ........................... 26
DETAIL SETTINGS Menu ............................................................................................................. 27
WHITE BALANCE ....................................................................................................................... 28
ADVANCED Feature ................................................................................................................... 29
COLOR CORRECTION ................................................................................................................. 30
3-6 DISPLAY Menu .......................................................................................................................... 31
3-7 NETWORK Menu ....................................................................................................................... 32
LAN_RJ45 ................................................................................................................................. 33
Wired LAN Terminal functionalites ............................................................................................. 33
Supported External Devices ....................................................................................................... 33
LAN_RJ45 ................................................................................................................................. 34
3-8 SETUP ....................................................................................................................................... 39
LIGHT MODE ............................................................................................................................. 40
STANDBY MODE ........................................................................................................................ 41
MENU ....................................................................................................................................... 42
SECURITY .................................................................................................................................. 43
3-9 INFO. Menu ............................................................................................................................... 44
Table of Contents
– ii –
4 Maintenance and Security ................................................................................................ 45
4-1 Cleaning the Projector ............................................................................................................... 45
Cleaning the Lens ..................................................................................................................... 45
Cleaning the Case ..................................................................................................................... 45
4-2 Using the Physical Lock ............................................................................................................. 46
Using the Security Slot............................................................................................................... 46
Using the Security Bar Lock ........................................................................................................ 46
5 Troubleshooting .............................................................................................................. 47
5-1 Common Problems and Solutions .............................................................................................. 47
5-2 Tips for Troubleshooting ........................................................................................................... 47
5-3 LED Error Messages ................................................................................................................... 48
5-4 Image Problems ........................................................................................................................ 48
5-5 Light Source Problems .............................................................................................................. 49
5-6 Remote Control Problems .......................................................................................................... 49
5-7 Audio Problems ........................................................................................................................ 49
5-8 Having the Projector Serviced .................................................................................................... 49
5-9 HDMI Q & A ............................................................................................................................... 50
6 Specifications ................................................................................................................... 51
6-1 Specifications............................................................................................................................ 51
6-2 Projection Distance vs. Projection Size ........................................................................................ 53
Projection Distance and Size Table ............................................................................................. 54
6-3 Timing Mode Table ................................................................................................................... 55
Table of Supported Frequency ................................................................................................... 55
Table of Supported Frequency For 3D mode ............................................................................... 57
6-4 Projector Dimensions ................................................................................................................ 58
7 Appendix I ........................................................................................................................ 59
7-1 RS-232C Protocol ...................................................................................................................... 59
REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and Mexico) ......................... 60
— iii —
Important Safety Information
It is strongly recommended that you read this section carefully before using the projector. These safety and
usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for
future reference.
About the Symbols
To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to
you and others as well as damage to property.
The symbols and their meanings are described below. Be sure to understand them thoroughly before reading this manual.
Failing to heed this symbol and handing the product erroneously could
result in accidents leading to death or major injury.
Failing to heed this symbol and handing the product erroneously could
result in personal injury or damage to surrounding property.
Examples of Symbols
This symbol indicates you should be careful of electric shocks.
This symbol indicates you should be careful of high temperatures.
This symbol indicates something that must be prohibited.
This symbol indicates something that must not be get wet.
This symbol indicates you should not touch with wet hands.
This symbol indicates something that must not be disassembled.
This symbol indicates things you must do.
This symbol indicates that the power cord should be unplugged from the power outlet.
Important Information
– iv –
Safety Caution
Handling the power cord
Please use the power cord supplied with this projector. If the supplied power cord
voltage and
current for your region, make sure to use the power cord that conforms to and satisfies them.
The power cord you use must be approved by and comply
with the safety standards of your country.
Rated voltage by country is listed below for your reference.
For selecting an appropriate power cord, please check rated
voltage for your region by yourself.
AC 230 V
European countries
AC 120 V
North America
The power cord included with this projector is exclusively for use with this projector. For safety, do not use it with other devices.
Handle the power cord with care. Damaging the cord could lead to fire or electric
shock.
- Do not place heavy objects on the cord.
- Do not place the cord under the projector.
- Do not cover the cord with a rug, etc.
- Do not scratch or modify the cord.
- Do not bend, twist or pull the cord with excessive force.
- Do not apply heat to the cord.
Should the cord be damaged (exposed core wires, broken wires, etc.), ask your
dealer to replace it.
Do not touch the power plug should you hear thunder. Doing so could result in
electric shock.
Important Information
– v –
Installing the Projector
This projector is designed to be used with a 100 240 V AC, 50/60 Hz power supply.
Before using the projector, check that the power supply to which the projector is to
be connected meets these requirements.
Use
directly to electrical light wiring. Doing so is dangerous.
Do not use in places such as those described below. Doing so could lead to fire or
electric shock.
- Shaky tables, inclined surfaces or other unstable places
- Near heating appliances or places with heavy vibrations
- Outdoors or humid or dusty places
- Places exposed to soot or steam
- Near cooking appliances, humidifiers, etc.
Do not use in places such as those described below where the projector could get
wet. Doing so could lead to fire or electric shock.
- Do not use in the rain or snow, on a seashore or waterfront, etc.
- Do not use in a bathroom or shower room.
- Do not place vases or potted plants on the projector.
- Do not place cups, cosmetics or medicines on the projector.
Should water, etc. get inside the projector, first turn off the power, then
unplug the power cord from the power outlet and contact your dealer
Do not insert or drop metal or combustible objects or other foreign materials into
the projector from the vents. Doing so could lead to fire or electric shock. Be particularly careful if there are children in the home. Should a foreign object get inside
the projector, first turn off the projectors power, then unplug the power cord from
the power outlet and contact your dealer.
Unplug the power cord if the projector malfunctions.
Should the projector emit smoke or strange odors or sounds, or if the projector has
been dropped or the cabinet broken, turn off the projectors power, then unplug
the power cord from the power outlet. Failure to do so could not only lead to fire
or electric shock, visual impairment or burn. it could also result in vision impair-
ment. Contact your dealer for repairs.
Never try to repair the projector on your own. Doing so is dangerous.
Do not disassemble the projector.
Do not remove or open the projectors cabinet.
Also, do not modify the projector. There are high voltage areas in the projector.
Modifying the projector could lead to fire, electric shock, or could lead to visual
impairment or burn by cause leakage of laser beams.
Have qualified service personnel perform inspection, adjustments and repairs of
the interior.
Important Information
– vi –
Installing suspended from the ceiling
Should special works be required, for example to suspend the projector from the
ceiling, consult your dealer.
Never try to install the projector yourself in such cases. The projector could drop
and cause injury.
Suspending the projector from the ceiling requires sufficient ceiling strength to
support the projector, and the building standards laws in your particular country
must be followed.
It is also necessary to take measures to prevent the projector from dropping in anticipation of a malfunction occurring in the projector, ceiling mounting device and
installation location.
When installed suspended from the ceiling, etc. do not hang from the projector.
The projector could drop and cause injury.
When installing suspended from the ceiling, use a power outlet that is within reach
so the power cord can be easily plugged and unplugged.
Do not place objects in front of the lens while the projector is operating.
Do not leave the lens cap on the lens while the projector is operating. The lens cap
could get hot and be warped.
Do not place objects in front of the lens that obstruct the light while the projector
is operating. The object could get hot and be broken or catch fire.
The below pictogram indicated on the cabinet means the precaution for avoiding
to place objects in front of the projector lens.
Important Information
– vii –
Strong light that could damage your eyes is projected when the projector is operating. Be especially careful when children are around.
Do not look at the projected light using optical devices (magnifying glasses, reflectors, etc.). Doing so could result in vision impairment.
Check that there is no one looking at the lens within the projection range before
turning on the projector.
Do not allow children to operate the projector alone. When a child is operating the
projector an adult should always be present and watch the child carefully.
The below pictogram, that is indicated near the lens on the cabinet, describes this
projector is categorized in the risk group 2 of IEC/EN 62471-5:2015.
When cleaning the projector
Do not use flammable gas sprays to remove dust from the lens, cabinet, etc. Doing
so could lead to fire.
As with any bright light source, do not stare into the beam, RG2 IEC/EN 624715:2015.
Important Information
– viii –
Connecting the power cord to earth
This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected to the earth, it may cause
electric shock. Please make sure the power cord is earthed properly.
Do not use a 2-core plug converter adapter.
Handling the power cord
connector is fully and firmly inserted. Loose connection of the power cord could
lead to fire or electric shock.
Do not connect or disconnect the power cord with wet hands. Doing so could
result in electric shock.
When cleaning the projector, for safety purposes unplug the power cord from the
power outlet beforehand.
When moving the projector, first be sure to turn off the power, unplug the power
cord from the power outlet and check that all connection cables connecting the
projector to other devices have been disconnected.
When planning not to use the projector for long periods of time, always unplug
the power cord from the power outlet.
Do not use on networks subject to overvoltage.
Connect the projectors Ethernet/HDBaseT port and LAN port to a network for
which there is no risk of overvoltage being applied.
Overvoltage applied to the Ethernet/HDBaseT or LAN port could result in electric
shock.
Lens shift, focus and zoom operations
When shifting the lens or adjusting the focus or zoom, do so from either behind or
to the side of the projector. If these operations are performed from the front, your
eyes could be exposed to strong light and get injured.
Keep your hands away from the lens area when performing the lens shift
operation. If not, your fingers could get caught in the gap between the cabinet and
the lens.
Important Information
– ix –
Handling batteries
Handle batteries with caution. Failure to do so could lead to fire, injury or contamination of the surroundings.
- Do not short-circuit or take apart batteries or dispose of them in flames.
- Do not use batteries other than those specified.
- Do not use new batteries together with old ones.
- When inse
be sure to insert them as indicated.
Contact your dealer or local authorities when disposing of batteries.
About the vents
Do not obstruct the projectors vents. Also, do not place such soft objects as paper
or cloths underneath the projector. Doing so could lead to fire.
Leave sufficient space between the place where the projector is installed and its
surroundings (as a general rule, at least 50cm/19.69 inches for the intake vent,
50cm/19.69 inches for the exhaust vent).
Do not touch the exhaust vent area while projecting or immediately after projecting images. The exhaust vent area may be hot at this time and touching it could
cause burns.
Moving the projector
When moving the projector, do not hold the lens section. The focus ring could
turn, causing the projector to drop and resulting in injury. Also, if you put your
hand on the gap between the cabinet and the lens, the projector may be
damaged, falling and causing injury.
Inspecting the projector and cleaning the inside
Consult with your dealer about once per year for cleaning of the inside of the
projector. Dust could accumulate inside of the projector if it is not cleaned for
extended periods of time, leading to fires or malfunction.
Important Information
– x –
Laser Safety Caution
Obey the laws and regulations of your country in relation to the installation and management of the device.
For China
This product is classified as Class 3R of GB 7247.1-2012.
CLASS 3R LASER PRODUCT OF GB 7247.1-2012
LASER RADIATION - AVOID DIRECT EYE EXPOSURE.
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
For other regions
This product is classified as Class 1 of IEC 60825-1 Third edition 2014-05 and RG2 of IEC/EN 62471-5 First edition.
CLASS 1 LASER PRODUCT OF IEC 60825-1 THIRD EDITION
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
Laser energy exposure near aperture may cause burns.
USA only
Complies with 21 CFR 1040.10 and 1040.11 except for conformance as a Risk Group 2 LIP as defined in IEC/EN
62471-5:Ed. 1.0. For more information see Laser Notice No. 57, dated May 8, 2019.
Do not allow to look into the projector beam at any distance from the projector. An adult should supervise the
children to prevent exposure risks.
Check that there is no one looking at the lens, when using the remote control for starting the projector.
Do not look at the projected light using optical devices(binoculars, telescopes, magnifying glasses, reflectors,
etc).
[ WARNING: MOUNT ABOVE THE HEADS OF CHILDREN. ]
The use of a ceiling mount is recommended with this product to place it above the eyes of children.
Outline of laser emitted from the built-in light module:
Wave length: 450 460 nm
Maximum power: 170 W
Radiation pattern from the protective housing:
Wave length: 450 460 nm
Maximum laser radiation output: 32 mW
Pulse duration: 1.34 ms
Repetition frequency: 120 Hz
The laser module is equipped in this product. Use of controls or adjustments of procedures other than those specified
herein may result in hazardous radiation exposure.
Light Module
A light module containing multiple laser diodes is equipped in the product as the light source.
These laser diodes are sealed in the light module. No maintenance or service is required for the performance of the
light module.
End user is not allowed to replace the light module.
Contact qualified distributor for light module replacement and further information.
Important Information
Product labels
The caution and the explanatory labels of the LASER PRODUCT in Class 1 conforming to IEC 60825-1 Third edition, and
in CLASS 3R conforming to GB 7247.1-2012 are stuck on the below indicated positions.
– xi –
Important Information
– xii –
Laser light radiation range
The figure below shows the maximum radiation range of the laser light. Horizontal angle (unit: degree).
Vertical angle (unit: degree)
Zoom
Lens position
Right most
Center (Reference value)
Left most
HR
HC
HL
Wide
32.3
24.3
32.3
Tele
22.7
16.6
22.7
Vertical angle (unit: degree)
Zoom
Lens position
Upper most
Center (Reference value)
Down most
VU
VC
VL
Wide
29.2
14.2
29.2
Tele
20.2
9.5
20.2
Important Information
– xiii –
Cable information
Use shielded cables or cables attached ferrite cores so as not to interfere with radio and television reception.
FCC Information (for USA only)
WARNING:
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
U.S. Responsible Party:
NEC Display Solutions of America, Inc.
Address:
3250 Lacey Rd, Ste 500
Downers Grove, IL 60515
Telephone Number:
630-467-3000
Type of Product:
Projector
Equipment Classification:
Class B Peripheral
Model Number:
NP-P506QL
Important Information
– xiv –
Disposing of your used product
In the European Union
EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household
waste. This includes projectors and their electrical accessories. When you dispose of such products,
please follow the guidance of your local authority and/or ask the shop where you purchased the
product.
After collecting the used products, they are reused and recycled in a proper way. This effort will
help us reduce the wastes as well as the negative impact to the human health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European Union
Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European union,
please contact your local authority and ask for the correct method of disposal.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general
household waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with legislation.
be separated to collect by local service.
(for Germany only)
Machine Noise Information Regulation 3.GPSGV,
The highest sound pressure level is less than 70 dB (A) in accordance with EN ISO 7779
Information of the AUDIO OUT mii jack
The AUDIO OUT mini jack does not support earphone/headphone terminal.
Important Information
– xv –
Do not install in places subject to vibrations or shocks.
If installed in places where the vibrations from power sources and the like are conveyed, or in vehicles or on vessels,
etc. the projector could be affected by vibrations or shocks that may dam- age internal parts and lead to malfunction.
Install in a place not subject to vibrations or shocks.
Do not install near high voltage power lines or power sources.
The projector may be affected by interference if it is installed near a high voltage power line or a power source.
Do not install or store in such places as those described below. Doing so could lead to malfunction.
- Places where strong magnetic fields are generated
- Places where corrosive gases are generated
If intense light like laser beams enters from the lens, it could lead to malfunction.
Consult your dealer before using in places where much cigarette smoke or dust is present.
When using the projector at altitudes of about 1,600 m/5,500 feet or higher, be sure to set the [FAN MODE] to [HIGH
ALTITUDE]. If not, the inside of the projector may get hot, leading to malfunction.
When the projector is used at high altitudes (places where the atmospheric pressure is low), it may be necessary to
replace the optical parts (light source, etc.) sooner than usual.
About moving the projector
- Be sure to mount the included lens cap to protect the lens from scratches.
- Do not subject the projector to vibrations or strong shocks. The projector could be damaged otherwise.
Improper handling, such as carrying the projector by the tilt feet or using it leaned against a wall, could lead to mal-
function.
Do not touch the surface of the projection lens with bare hands.
Fingerprints or dirt on the surface of the projection lens will be enlarged and projected on the screen. Do not touch
the surface of the projection lens.
Do not unplug the power cord from the projector or the power outlet while projecting. Doing so could cause dete-
being projected, use a power strip switch, a breaker, etc.
About handling of the remote control
-
is exposed to strong light or if there are obstacles between them that obstruct the signals.
- Op
sensor.
- Do not drop the remote control or handle it improperly.
- Do not let water or other liquids get on the remote control. Should the remote control get wet, wipe it off imme-
diately.
- Avoid using in hot and humid places as far as possible.
- When planning not to use the remote control for long periods of time, remove both batteries.
Take measures to prevent external light from shining on the screen.
Make sure only the light from the projector shines on the screen. The less external light on the screen, the higher the
contrast and the more beautiful the images.
About screens
Images will not be clear if there is dirt, scratches, discoloration, etc. on your screen. Handle the screen with care,
protecting it from volatile substances, scratches and dirt.
Important Information
– xvi –
Clearance for Installing the Projector
When installing the projector, keep sufficient space around it, as described below. If not, the hot exhaust emitted from
the projector may be taken back in.
Also, make sure no wind from an air-conditioner hits the projector.
power.
NOTE:
In the above figure, it is assumed that there is sufficient space above the projector. There is also an intake vent on
the back. Leave about 50 cm or more space behind, and even more space for installing the cables.
Precautions for Ceiling Installation
Do not install the projector in the following places. Attached substances such as oil, chemicals and moisture may cause
deformation or cracks of the cabinet, corrosion of the metal parts, or malfunction.
• Outdoors and places with humid or dust
• Places exposed to oil smoke or steam
• Places where corrosive gases are generated
Important Information
– xvii –
About Copyright of original projected pictures:
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a
venue such as a coffee shop or hotel and employing compression or expansion of the screen image with the
following functions may raise concern about the infringement of copyrights which are protected by copyright law.
[ASPECT RATIO], [KEYSTONE], Magnifying feature and other similar features.
Power management function
The projector has power management functions. To reduce power consumption, the power management
functions (1 and 2) are factory preset as shown below. To control the projector from an external device via a
LAN or serial cable connection, use the on-screen menu to change the settings for 1 and 2.
1. STANDBY MODE (Factory preset: NORMAL)
To control the projector from an external device, select [NETWORK STANDBY] or [HDBaseT] for
[STANDBY MODE]. (→ page 41)
2. AUTO POWER OFF (Factory preset: 0)
To control the projector from an external device, select [0] for [AUTO POWER OFF]. (→page 41)
Important Information
– xviii –
Trademarks
Microsoft, Windows, and Internet Explorer are either a registered trademark or trademark of Microsoft Corporation
in the United States and/or other countries.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trade- marks or registered
trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
PJLink trademark and logo are trademarks applied for registration or are already registered in Japan, the United
States of America and other countries and areas.
CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of Crestron Electronics, Inc. in the
United States and other countries.
Ethernet is either a registered trademark or trademark of Fuji Xerox Co., Ltd.
trademarks of their respective holders.
GPL/LGPL Software Licenses
The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License
(LGPL), and others.
-
ROM.
Getting Started
— 1 —
1 Getting Started
1-1 Packing Checklist
Carefully unpack the projector and check that the following items are included:
Lens cap Projector
79TL0851
Remote Control
(Batteries Included)
7N901261
Computer cable(VGA)
79TL0841
Power Cord (US)
79TL0801
Power Cord (EU)
79TL0811
CD-ROM
(This User's Manual)
7N953001
Important Information
7N8R0401
Security Sticker
24L67991
Quick Setup Guide
7N8R0421
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is
recommend that you keep the original packing material should you ever need to return the equipment for warranty
service.
For North America only
Limited warranty
For customers in Europe:
You will find our current valid Guarantee Policy on our Web Site:
https://www.nec-display-solutions.com
QuickSetupGuide
1 Getting Started
– 2 –
1-2 Views of Projector Parts
Front-right View
5
10
8
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Intake Vent
Cool air intake
2.
Zoom lever
Enlarges the projected image.
17
3.
Focus Ring
Focuses the projected image.
17
4.
Lens
Projection Lens.
5.
Remote Sensor
Receives IR signal from remote control.
6.
Monaural Speaker
Outputs audio sound.
7.
Indicators
Display the messages of projector.
8.
Tilt Foot
Rotate adjuster lever to adjust angle position.
14
9.
Lens Shift
Adjusts the image position.
15
10.
Exhaust Vent
Hot air exhaust
Caution
Ventilation openings on the projector allow for good air circulation, which keeps the projector light source cool. Do
not obstruct any of the ventilation openings.
1 Getting Started
– 3 –
Top view
1
2
3
4
5 6
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
POWER Indicator
Display the power on/off sequence status.
48
2.
STATUS Indicator
Display the status of projector.
3.
Light Indicator
Display the light source status.
4.
Temp Indicator
Display the thermal status.
5.
Vertical Lens Shift
(UP / DOWN)
Adjusts the image position vertically.
16
6.
Horizontal Lens Shift
(LEFT / RIGHT)
Adjusts the image position horizontally.
16
1 Getting Started
– 4 –
Rear view-On-screen Display (OSD) buttons
1 2 3 4 5
7
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
INPUT
Enter the Source menu.
2.
Navigates and changes settings in the OSD.
Quick Menu For Volume.
19
3.
Navigates and changes settings in the OSD.
19
4.
Navigates and changes settings in the OSD.
Quick Menu For Volume.
19
5.
Turn the projector on or off.
12
6.
EXIT
Return to last OSD page.
7.
ENTER
Enter or confirm highlighted OSD menu item.
19
8.
Navigates and changes settings in the OSD.
19
9.
MENU
Opens and exits OSD menus.
19
1 Getting Started
– 5 –
Rear view (Terminal Panel)
1 2 3 4 5 6 7 8 9 10
1211
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
SERVICE
For service personnel only.
2.
USB POWER (5V/2.0A)
5V POWER supply Only..
Note: Support 5V/2.0A output as long as the projector Power On.
3.
AUDIO OUT
Connect an AUDIO cable for audio loop through.
4.
AUDIO IN
Connect an AUDIO cable from the audio device.
5.
COMPUTER IN
Connect an RGB cable from a computer.
6.
HDMI 1 IN
Connect the HDMI cable from an HDMI device.
7.
HDMI 2 IN
Connect the HDMI cable from an HDMI device.
8.
Ethernet HDBaseT
Connect a LAN cable from Ethernet.
Connect Cat5e/Cat6 cable from HDBaseT TX Box (VIDEO EXTENDER) for
HDBaseT signal received.
9.
LAN
Connect a LAN cable from Ethernet.
10.
PC CONTROL
Connects RS-232 serial port cable for remote control.
11.
3D-SYNC
Connect 3D-sync in cable from a computer or an enabled device.
12.
AC IN
Connect the POWER cable.
13.
Security chain opening
Secures to permanent object with a Kensington Lock
system.
46
Note:
To use this feature, you must plug in the connector before turn on/off the projector.
Do not use this jack for anything other than intended use.
Note:
As a safety precaution, disconnect all power to the projector and connecting devices before making connections.
1 Getting Started
– 6 –
Bottom view
1
2
2
250mm
[ 9.84" ]
200mm
[ 7.87" ]
1
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Ceiling Mount Holes
Contact your dealer for information on mounting the projector on a
ceiling.
2.
Tilt Foot
Rotate adjuster lever to adjust angle position.
14
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 8 mm
(0.315 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity
must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding
three times the weight of the equipment over a period of 60 seconds.
1 Getting Started
– 7 –
Reference drawings for stand
Please hire an installation service provider (for a fee) for the design and manufacture of a customized stand to be used
for portrait projection. Please ensure that the design complies with the following conditions:
Use the 4 screw holes at the back of the projector to secure it to the stand.
Screw hole center dimension: 250 × 200 mm
Screw hole dimension on the projector: M4 with the maximum depth 12 mm
Horizontal adjustment mechanism (for example, bolts and nuts in 4 places)
Please design the stand so that it does not easily topple over.
The drawing showing the dimensional requirements is not an actual stand design drawing.
250mm
[ 9.8 4" ]
200mm
[ 7.87" ]
50mm
[ 19.69" ]
[Side View ]
[Front View]
Horizont al adjust er
Air exhaus t
Air intak e
Air intak e
Air exhaus t
1 Getting Started
– 8 –
1-3 Remote Control Specification
Note:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can
disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote
control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector
screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote
1 Getting Started
– 9 –
Key Name
Short
ON
Power ON
STANDBY
Power OFF
SOURCE
Display Menu of INPUT SELECT
HDMI1
Change Input to HDMI1
HDMI2
Change Input to HDMI2
HDBaseT
Change Input to HDBaseT
DispalyPort
-
COMPUTER
Change Input to COMPUTER
AUTO ADJ.
-
VIDEO
-
USB-A
-
USB-B
-
ID - APPS
-
PIP - MENU
Menu Operation
AV-MUTE
AV Mute ON / OFF
FREEZE
Freeze ON / OFF
EXIT
Menu Operation
UP
Menu Operation
ENTER
Menu Operation
LEFT
Menu Operation
RIGHT
Menu Operation
DOWN
Menu Operation
D-ZOOM +
Zoom Up
D-ZOOM -
Zoom Down
PAGE UP
-
PAGE DOWN
-
L-CLICK
-
R-CLICK
-
ECO
Display Menu of LIGHT MODE tab directly
KEYSTONE
Display Menu of DISPLAY tab and set UI focus to KEYSTONE
PICTURE
Toggle display direct menu of CONTRAST/BRIGHTNESS/SHARPNESS
VOLUME +
Adjust Volume Up directly
HELP
Display Menu of INFO tab directly
FOCUS/ZOOM
-
ASPECT
Display Menu of ADJUST tab directly and set UI focus to ASPECT RATIO
VOLUME -
Adjust Volume Down directly
1 Getting Started
– 10 –
1-4 Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at
the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the
remote will function well within a radius of about 7 meters (23 feet) and 30 degrees above or below the projector level.
If the projector does not respond to the remote control, move a little closer.
1-5 Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All operations can
be carried out with the remote control; however, the buttons on the projector are limited in use.
Setup and Operation
— 11 —
2 Setup and Operation
2-1 Inserting the Remote Control Batteries
1.
Remove the battery compartment cover
by sliding the cover in the direction of
the arrow.
2.
Insert the battery with the positive side
facing up.
3.
Replace the cover.
Remote Control Precautions
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
4. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
5. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
O
P
E
N
O
P
E
N
2 Setup and Operation
– 12 –
2-2 Starting and Shutting down the Projector
1.
Securely connect the power cord and signal
cable. When connected, the power led will
flash green to solid green.
2.
Turn on the light source
remote control.
The PWR LED will now flash blue.
The startup screen will display in
approximately 30 seconds. The first time
you use the projector, you can select your
preferred language from quick menu after
the startup screen display. (See Setting the
OSD Language on page 20)
2 Setup and Operation
– 13 –
3.
If more than one input device is connected,
press the SOURCE button and use to
scroll among devices.
HDMI 1: High-Definition Multimedia Interface compatible
HDMI 2: High-Definition Multimedia Interface compatible
COMPUTER: Analog RGB
HDBaseT: Support for distribution of HD video, digital audio
content, RS232, RJ45 and IR function over standard CAT5e/6 LAN
cable.
Note:
It is recommended to use a certified TX box (VIDEO EXTENDER)
Rextron (EVBMN-110L38) for the HDBaseT function and there is
no guarantee of full response when other brands of TX box are
used..
Using a single HDBaseT CAT5e cable, the projector supports an
HDBaseT connection distances to 100m/328ft.
4.
POWER OFF ARE YOU SURE
message appears, press the POWER button.
The projector turns off.
Caution:
Do not unplug the power cord until the POWER LED stops flashing indicating the projector has cooled down.
2 Setup and Operation
– 14 –
2-3 Adjusting the Projector Level
Take note of the following when setting up the projector:
1.
To raise the level of the projector, twist the
adjusters counter clockwise.
2.
To lower the level of the projector, lift the
projector and twist the adjusters clockwise.
2 Setup and Operation
– 15 –
2-4 Adjusting Projected Image Position Using Lens Shift
The Lens Shift feature provides a lens shift function that can be used to adjust the position of the projected image
either horizontally or vertically within the range detailed below.
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio than traditional
lens shift systems.
Note:
Do not rotate lens shift knob further under click sound and lightly press the knob to rotate back.
2 Setup and Operation
– 16 –
Adjusting the vertical image position
The vertical image height can be adjusted around 60% for UHD of offset position. Note that the maximum vertical
image height adjustment can be limited by the horizontal image position. For example it is not possible to achieve the
maximum vertical image position height detailed above if the horizontal image position is at maximum. Please consult
the Shift Range diagram below for further clarification.
Adjusting the horizontal image position
With the lens horizontal image position can be adjusted to a maximum of 20% for UHD of the image width. Note that
the maximum horizontal image height adjustment can be limited by the vertical image position. For example it is not
possible to achieve the maximum horizontal image position if the vertical image position is at maximum. Please
consult the Shift Range diagram below for further clarification.
Lens Shift Range Diagram
2 Setup and Operation
– 17 –
2-5 Adjusting the Zoom, Focus and Keystone
1.
Use the Image-zoom control (on the projector
only) to resize the projected image and screen
size .
2.
Use the Image-focus control (on the projector
only) to sharpen the projected image .
3.
Press the Keystone and button (on the
remote) to selected V (Vertical) keystone.
A
B
2 Setup and Operation
– 18 –
2-6 Adjusting the Volume
1.
Press the Volume +/- buttons on the remote
control.or press the / buttons on the
keypad to adjust Volume +/-.
.
2.
The volume control appears on the display
3.
Press the AV-MUTE button to turn off the
image and volume (This feature is available
only on the remote).
On-Screen Display (OSD) Menu Settings
— 19 —
3 On-Screen Display (OSD) Menu Settings
3-1 OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the projector to navigate and make changes to the
OSD. The following illustration shows the corresponding buttons on the projector.
1
1
2
2
3
3
4
4
5
5
5
6
6
1. To enter the OSD, press the MENU button.
2. There are six menus. Press the cursor / buttons
to move through the menus.
3. Press the cursor / buttons to move up and
down in a menu.
4. Press the cursor / buttons to change values for
settings.
5. Press the MENU button to close the OSD or leave a
submenu. Press the EXIT button to return to the
previous menu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical
Position items in the Computer menu can only be modified when connected to a PC. Items that are not available
cannot be accessed and are grayed out.
3 On-Screen Display (OSD) Menu Settings
– 20 –
3-2 Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor button to navigate to SETUP
2. Press the cursor button until LANGUAGE is highlighted.
3. Press the cursor button until the language you want is highlighted.
4. Press the MENU button to close the OSD.
3 On-Screen Display (OSD) Menu Settings
– 21 –
3-3 OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
Main
Menu
Sub Menu
Settings
INPUT
HDMI
VIDEO LEVEL
AUTO, NORMAL, ENHANCED
COMPUTER
H POSITION
-5~5
V POSITION
-5~5
PHASE
0~100
CLOCK
-5~5
3D
GLASSES
DLP-LINK, IR
SYNC INVERT
OFF, ON
AUTO SOURCE
OFF, ON
TEST PATTERN
OFF, GRID
ADJUST
REFERENCE
HIGH-BRIGHT, PRESENTATION,
VIDEO, MOVIE, sRGB, DICOM,
USER, HDR
DETAIL SETTINGS
GAMMA CORRECTION
1.8, 2, 2.2, 2.4, B&W, LINEAR
COLOR TEMPERATURE
WARM, NORMAL, COLD
DYNAMIC CONTRAST
OFF, ON
WHITE BALANCE
CONTRAST R
0~200
CONTRAST G
0~200
CONTRAST B
0~200
BRIGHTNESS R
-100~100
BRIGHTNESS G
-100~100
BRIGHTNESS B
-100~100
ADVANCED
WHITE PEAKING
0~10
MEMC
OFF, LOW, MEDIUM, HIGH
IMAGE PEAKING
OFF, 0~10
COLOR
CORRECTION
COLOR
RED, GREEN, BLUE, YELLOW,
MAGENTA, CYAN, WHITE
HUE
0~100
SATURATION
0~100
GAIN
0~100
CONTRAST
0~100
BRIGHTNESS
0~100
SHARPNESS
0~31
AUDIO
VOLUME
0~31
RESET
CANCEL, OK
3 On-Screen Display (OSD) Menu Settings
– 22 –
Main Menu
Sub Menu
Settings
DISPLAY
ASPECT RATIO
FILL, 4:3, 16:9, LETTER BOX
DIGITAL ZOOM
-10~10
KEYSTONE
-30~30
ORIENTATION
DESKTOP FRONT, DESKTOP REAR, CEILING FRONT, CEILING
REAR
NETWORK
CONNECT
DISABLE, ENABLE
DHCP
OFF, ON
IP ADDRESS
0~ 255, 0~ 255, 0~ 255, 0~ 255
SUBNET MASK
0~ 255, 0~ 255, 0~ 255, 0~ 255
GATEWAY
0~ 255, 0~ 255, 0~ 255, 0~ 255
DNS
0~ 255, 0~ 255, 0~ 255, 0~ 255
APPLY
CANCEL, OK
AMX BEACON
OFF, ON
SETUP
LIGHT MODE
ECO MODE
NORMAL, ECO
ADJUST
30 ~100
CONSTANT BRIGHTNESS
OFF, ON
FAN MODE
NORMAL, HIGH ALTITUDE
REMOTE SENSOR
ALL, FRONT, BACK
STANDBY
STANDBY MODE
NORMAL, NETWORK STANDBY, HDBaseT
AUTO POWER OFF
0~180
OFF TIMER
0~600
DIRECT POWER ON
OFF, ON
MENU
MESSAGE DISPLAY
OFF, ON
MENU POSITION
CENTER, UP, DOWN, LEFT, RIGHT
DISPLAY TIME
MANUAL, AUTO 5SEC, AUTO 15SEC, AUTO 45SEC
BACKGROUND
BLUE, BLACK
SECURITY
CONTROL PANEL LOCK
OFF, ON
LANGUAGE
ENGLISH, DEUTSCH, FRANCAIS, ITALIANO, ESPAÑOL,
SVENSKA, 日本語, DANSK, PORTUGUÊS, MAGYAR, POLSKI,
,
한국어
INDONESIA, ไทย, , ,, 繁體中文
RESET ALL
CANCEL, OK
INFO.
INPUT TERMINAL
SOURCE NAME
LIGHT HOURS
USED
IP ADDRESS
VERSION
SERIAL NUMBER
3 On-Screen Display (OSD) Menu Settings
– 23 –
3-4 INPUT Menu
Attention
All of display mode parameters when changed will be saved to user mode.
Press the MENU button to open the OSD menu. Press the cursor button to move to the INPUT Menu. Press the
cursor button to move up and down in the INPUT menu. Press to enter and change values for settings.
ITEM
DESCRIPTION
HDMI
Press the cursor button to enter and set the HDMI.
COMPUTER
Press Enter to enter the Computer menu. See COMPUTER Menu on page 24.
3D
Press Enter to enter the 3D menu. See 3D Setting on page 25.
AUTO SOURCE
Press the cursor button to enter and set the Auto Source.
TEST PATTERN
Press the cursor button to enter and select internal Test Pattern.
Note:
To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under the 3D Disc Menu.
3 On-Screen Display (OSD) Menu Settings
– 24 –
COMPUTER Menu
Press the Menu button to open the OSD menu. Press to move to the ADJUST menu. Press to move to the
COMPUTER menu and then press Enter or . Press to move up and down in the COMPUTER menu.
ITEM
DESCRIPTION
H POSITION
Press the cursor button to enter and adjust the display position to left or right.
V POSITION
Press the cursor button to enter and adjust the display position to up or down.
PHASE
Press the cursor button to enter and adjust the A/D clock timing phase..
CLOCK
Press the cursor button to enter and adjust the A/D sampling dots.
3 On-Screen Display (OSD) Menu Settings
– 25 –
3D Setting
ITEM
DESCRIPTION
GLASSES
Press the cursor button to enter and select different 3D mode.
SYNC INVERT
Press the cursor button to enter and enable or disable 3D Sync Invert.
Note:
1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.
2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for selection.
3. Use 3D glasses to view a 3D image.
4. You need 3D content from a 3D DVD or 3D media file.
5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature).
6. You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a driver on your PC and
connect a USB emitter.
7. The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D).
8. Power on the glasses. Glasses normally have a power on -off switch.
Each type of glasses has their own configuration instructions. Please follow the configuration instructions that come
with your glasses to finish the setup process.
9. Passive 3D is not going to support thru 3D Sync In/Out.
10. It takes around 30 seconds to enable or disable 3D function.
Note:
Since different types of glass (DLP link or IR shutter glass) have their own setting instructions, Please follow the guide
to finish the setup process.
3 On-Screen Display (OSD) Menu Settings
– 26 –
3-5 ADJUST Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the ADJUST Menu. Press the
cursor button to move up and down in the ADJUST menu. Press to enter and change values for settings.
ITEM
DESCRIPTION
REFERENCE
Press the cursor button to enter and set the Reference Mode.
DETAIL SETTINGS
Press Enter to enter the Detail Settings menu. See 3D Setting on page 25.
COLOR CORRECTION
Press Enter to enter the Color Correction menu. See page 30 for more information on
COLOR CORRECTION
CONTRAST
Press the cursor button to enter and adjust the display Contrast.
BRIGHTNESS
Press the cursor button to enter and adjust the display Brightness.
SHARPNESS
Press the cursor button to enter and adjust the display Sharpness.
AUDIO
Press Enter to enter the Audio menu and adjust the volume
RESET
Press Enter to reset all picture settings to default values.
3 On-Screen Display (OSD) Menu Settings
– 27 –
DETAIL SETTINGS Menu
Press the MENU button to open the OSD menu. Press to move to the ADJUST menu. Press to move to the
DETAIL SETTINGS menu and then press Enter or . Press to move up and down in the DETAIL SETTINGS menu.
ITEM
DESCRIPTION
GAMMA
CORRECTION
Press the cursor button to enter and adjust the Gamma Correction of the display.
COLOR TEMPERTURE
Press the cursor button to enter and adjust the Color Temperature.
DYNAMIC
CONTRAST
Press the cursor button to enter and enable or disable the Dynamic Contrast.
WHITE BALANCE
Press the Enter button to enter the White Balance sub menu. See WHITE BALANCE on
page 28
ADVANCED
Press Enter to enter the Advanced menu. See ADVANCED Feature on page 29.
3 On-Screen Display (OSD) Menu Settings
– 28 –
WHITE BALANCE
Press the ENTER button to enter the WHITE BALANCE sub menu.
ITEM
DESCRIPTION
CONTRAST R
Press the buttons to adjust the Red Contrast.
CONTRAST G
Press the buttons to adjust the Green Contrast.
CONTRAST B
Press the buttons to adjust the Blue Contrast.
BRIGHTNESS R
Press the buttons to adjust the Red Brightness.
BRIGHTNESS G
Press the buttons to adjust the Green Brightness.
BRIGHTNESS B
Press the buttons to adjust the Blue Brightness.
3 On-Screen Display (OSD) Menu Settings
– 29 –
ADVANCED Feature
Press the ENTER button to enter the ADVANCED sub menu.
ITEM
DESCRIPTION
WHITE PEAKING
Press the cursor button to enter and adjust the White Peaking value.
MEMC
Press the buttons to select different MEMC level.
IMAGE PEAKING
Press the buttons to adjust motion adaptive sharpness enhancement (2D Peaking)
value.
3 On-Screen Display (OSD) Menu Settings
– 30 –
COLOR CORRECTION
Press the Menu button to open the OSD menu. Press to move to the ADJUST menu. Press to move to the
COLOR CORRECTION menu and then press Enter or . Press to move up and down in the COLOR CORRECTION
menu.
ITEM
DESCRIPTION
COLOR
Press the buttons to select RED, GREEN, BLUE, YELLOW, MAGENTA, CYAN or WHITE.
RED
Select to enter the Red Color Correction.
Press the buttons to adjust the Hue, Saturation, and Gain.
GREEN
Select to enter the Green Color Correction.
Press the buttons to adjust the Hue, Saturation, and Gain.
BLUE
Select to enter the Blue Color Correction.
Press the buttons to adjust the Hue, Saturation, and Gain.
YELLOW
Select to enter the Yellow Color Correction.
Press the buttons to adjust the Hue, Saturation, and Gain.
MAGENTA
Select to enter the Magenta Color Correction.
Press the buttons to adjust the Hue, Saturation, and Gain.
CYAN
Select to enter the Cyan Color Correction.
Press the buttons to adjust the Hue, Saturation, and Gain.
WHITE
Select to enter the White Color Correction.
Press the buttons to adjust the Red, Green, and Blue.
3 On-Screen Display (OSD) Menu Settings
– 31 –
3-6 DISPLAY Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the DISPLAY menu. Press the
cursor button to move up and down in the DISPLAY menu. Press to enter and change values for settings.
ITEM
DESCRIPTION
ASPECT RATIO
Press the cursor button to enter and adjust the video Aspect Ratio.
DIGITAL ZOOM
Press the cursor button to enter and adjust the Digital Zoom.
KEYSTONE
Press the cursor button to enter and adjust the Keystone.
ORIENTATION
Press the cursor button to enter and choose from four Orientation methods.
Note:
ASPECT RATIO, such as 1280 x 1024(4:3), the image would be scaling to FILL 16:9 with distortion.
3 On-Screen Display (OSD) Menu Settings
– 32 –
3-7 NETWORK Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the NETWORK menu. Press
the cursor button to move up and down in the NETWORK menu. Press to enter and change values for
settings.
ITEM
DESCRIPTION
CONNECT
Displays the network connection status.
DHCP
Press to turn DHCP On or Off.
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS
fields.
IP ADDRESS
Enter a valid IP address if DHCP is turned off.
SUBNET MASK
Enter a valid Subnet Mask if DHCP is turned off.
GATEWAY
Enter a valid Gateway address if DHCP is turned off.
DNS
Enter a valid DNS name if DHCP is turned off.
APPLY
Press Enter to confirm settings.
AMX BEACON
Press the cursor button to enter and adjust the AMX Beacon.
3 On-Screen Display (OSD) Menu Settings
– 33 –
LAN_RJ45
Wired LAN Terminal functionalites
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. Compatibility with
Crestron / AMX (Device Discovery) enables not only collective projector management on a network but also
management from a control panel on a PC (or Laptop) browser screen.
Supported External Devices
This projector is supported by the specified commands of the Crestron Electronics controller and related software (ex,
RoomView ®).
http://www.crestron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
For more detail of information about the diverse types of external devices which can be connected to the LAN/RJ45
port and remote/control the projector, as well as the related control commands supporting for each external device,
kindly please get contact with the Support-Service team directly.
3 On-Screen Display (OSD) Menu Settings
– 34 –
LAN_RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).
2. On the PC (Laptop), select Start → Settings →Network & Internet →Ethernet →Change adapter options.
3 On-Screen Display (OSD) Menu Settings
– 35 –
3 On-Screen Display (OSD) Menu Settings
– 36 –
3. Right-click on Ethernet, and select Properties.
4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP).
5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
3 On-Screen Display (OSD) Menu Settings
– 37 –
7. Press the Menu button on the projector.
8. Select Settings2→ Advanced1 → Network
9. After getting into Network, input the following:
DHCP: Off
IP Address: 10.10.10.10
Subnet Mask: 255.255.255.0
Gateway: 0.0.0.0
DNS Server: 0.0.0.0
10. Press (Enter) / to confirm settings.
Open a web browser
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher).
11. In the Address bar, input the IP address: 10.10.10.10.
12. Press (Enter) / .
The projector is setup for remote management. The LAN/RJ45 function displays as follows.
3 On-Screen Display (OSD) Menu Settings
– 38 –
CATEGORY
ITEM
INPUT-LENGTH
Crestron Control
IP Address
15
IP ID
3
Port
5
Projector
Projector Name
10
Location
10
Assigned To
10
Network Configuration
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
User Password
Enabled
(N/A)
New Password
10
Confirm
10
Admin Password
Enabled
(N/A)
New Password
10
Confirm
10
For more information, please visit http://www.crestron.com.
3 On-Screen Display (OSD) Menu Settings
– 39 –
3-8 SETUP
Press the MENU button to open the OSD menu. Press the cursor button to move to the SETUP menu. Press the
cursor button to move up and down in the SETUP menu. Press to enter and change values for settings.
ITEM
DESCRIPTION
LIGHT MODE
Press Enter to enter the Light mode menu. See page 40 for more information on LIGHT
MODE.
FAN MODE
Press the cursor button to enter and toggle between Normal and High fan speeds.
Note: We recommend selecting high speed in high temperatures, high humidity, or high
altitude (higher than 1500m/4921ft) areas.
REMOTE SENSOR
Press the cursor button to enter and select Remote Sensor.
STANDBY
Press Enter to enter the Standby menu. See page 41 for more information on STANDBY
MODE .
DIRECT POWER ON
Press the cursor button to enter and enable or disable automatic power On when AC
power is supplied.
MENU
Press Enter to enter the MENU menu. See page 42 for more information on MENU.
SECURITY
Press Enter to enter the Security menu. See page 43 for more information on SECURITY.
LANGUAGE
Press the cursor button to enter and select a different localization Menu.
RESET ALL
Press Enter to reset all settings to default values (except Language).
3 On-Screen Display (OSD) Menu Settings
– 40 –
LIGHT MODE
Press the MENU button to open the OSD menu. Press to move to the SETUP menu. Press to move to the
LIGHT MODE menu and then press Enter or . Press to move up and down in the LIGHT MODE menu.
ITEM
DESCRIPTION
ECO MODE
Press the cursor button to enter and adjust the ECO Mode.
ADJUST
Press the cursor button to enter and adjust the brightness level.
CONSTANT
BRIGHTNESS
Press the cursor button to enter and enable or disable the Constant Brightness.
3 On-Screen Display (OSD) Menu Settings
– 41 –
STANDBY MODE
Press the MENU button to open the OSD menu. Press to move to the SETUP menu. Press to move to the
STANDBY MODE menu and then press Enter or . Press to move up and down in the STANDBY MODE menu.
ITEM
DESCRIPTION
STANDBY MODE
Press the cursor button to select the standby mode.
The options are NORMAL, NETWORK STANDBY and HDBaseT
AUTO POWER OFF
Press the cursor buttons to set the Auto Power Off timer. The projector automatically
turns off if no input source is detected after the preset period of time.
OFF TIMER
Press the cursor button to enter and set Sleep timer. The projector automatically turns
off after the preset period of time.
3 On-Screen Display (OSD) Menu Settings
– 42 –
MENU
Press the MENU button to open the OSD menu. Press to move to the SETUP menu. Press to move to the
MENU menu and then press Enter or . Press to move up and down in the MENU menu.
ITEM
DESCRIPTION
MESSAGE DISPLAY
Press the cursor button to enter and enable or disable the Message Display.
MENU POSITION
Press the cursor button to enter and select Menu Position.
DISPLAY TIME
Press the cursor button to enter and select Display Time.
BACKGROUND
Press the cursor button to enter and select Background.
3 On-Screen Display (OSD) Menu Settings
– 43 –
SECURITY
Press the MENU button to open the OSD menu. Press to move to the SETUP menu. Press to move to the
SECURITY menu and then press Enter or . Press to move up and down in the SECURITY menu.
ITEM
DESCRIPTION
CONTROL PANEL
LOCK
Press the cursor button to enter and set Control Panel Lock.
3 On-Screen Display (OSD) Menu Settings
– 44 –
3-9 INFO. Menu
Press the MENU button to open the OSD menu. Press the cursor button to move to the INFO. menu. Press the
cursor button to move up and down in the INFO. menu.
ITEM
DESCRIPTION
INPUT TERMINAL
Display the activated source.
SOURCE NAME
Displays resolution/video information for RGB source and color standard for Video source.
LIGHT HOURS USED
Light hour used information is displayed.
IP ADDRESS
Showing IP Address.
VERSION
Showing system software version.
SERIAL NUMBER
Showing serial number of product.
Maintenance and Security
— 45 —
4 Maintenance and Security
4-1 Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a
severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the
projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for
several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
Remove the lens cap before wiping the lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe
the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
4 Maintenance and Security
– 46 –
4-2 Using the Physical Lock
Using the Security Slot
If you are concerned about security, attach the projector to a permanent object with the security slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock
Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, http://www.Kensington.com.
Using the Security Bar Lock
In addition to the password protection function and the Kensington lock, the Security Bar Opening helps protect the
projector from unauthorized use.
See the following picture.
Troubleshooting
— 47 —
5 Troubleshooting
5-1 Common Problems and Solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem
remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the
following before proceeding to the problem-specific solutions.
-
5-2 Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more
quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical
support or for passing on to service personnel.
5 Troubleshooting
– 48 –
1 2 3 4
5-3 LED Error Messages
① POWER LED
② STATUS LED
③ LIGHT LED
④ TEMP. LED
Error over view
POWER
STATUS
LAMP
TEMP.
temperature failure (thermistor)
Red
(Blink)
top cover cover failure
Red
(Blink)
Red
(Light)
Green
(Light)
Fan failure
Red
(Light)
Orange
(Light)
LD Bank/Driver error
Red
(Light)
Orange
(Light)
Orange
(Light)
Slave CPU communication error
Red
(Light)
Orange
(Light)
Orange
(Light)
PW/CW spin failed (Include laser driver BD)
Red
(Light)
Red
(Light)
Orange
(Light)
5-4 Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the ORIENTATION setting on the DISPLAY menu of the OSD.
Problem: The image is streaked
5 Troubleshooting
– 49 –
Problem: The image is flat with no contrast
Adjust the CONTRAST setting on the ADJUST menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the COLOR TEMPERATURE and GAMMA settings on the ADJUST -> DETAIL SETTINGS menu of the OSD.
5-5 Light Source Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is on.
5-6 Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
5-7 Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
5-8 Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton.
Include a description of the problem and a checklist of the steps you took when trying to fix the problem: The
information may be useful to service personnel. For servicing, return the projector to the place you purchased it.
5 Troubleshooting
– 50 –
5-9 HDMI Q & A
HDMI - HDMI cable?
Recently, HDMI Licensing Administrator, Inc. announced that cables would be tested as Standard or HighSpeed cables.
HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps,
which is the equivalent of a 720p/1080i signal.
HDMI cables have been tested to perform at speeds of 340Mhz or up to
10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can successfully handle
1080p signals including those at increased color depths and/or increased refresh rates from the Source. HighSpeed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors
(resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI
typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that
include active cables (active electronics built into cables that boost
amplifiers as well as CAT5/6 and fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test
Specification. However, there may be instances where cables bearing the HDMI logo are available but have not
been properly tested. HDMI Licensing Administrator, Inc. actively investigates these instances to ensure that
the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from a
reputable source and a company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
Specifications
— 51 —
6 Specifications
6-1 Specifications
Model Name
NP-P506QL
Display Type
0.47" (11.9mm) TRP
Resolution
1080p, 4K UHD w/ pixel shift
Throw Ratio
1.127(Wide) ~1.697(Tele)
Zoom Ratio
1.5X
Contrast ratio(all
white/all black)
500,000:1 with dynamic contrast
F-number / focal length
1.8 (Wide) ~ 2.43 (Tele) / 12.1 ~18.1 mm
Lens Shift
H: +/-0.2 V: +/-0.6
Image size (diagonal)
50" (1270mm) (Tele) to 310" (7874mm) (Wide) inches
Projection distance
1.6m (63") ~ 8m (315")
Keystone
Correction
Vertical
+/- 30 steps
Projection Methods
Front, Rear, Desktop/Ceiling (Rear, Front)
Data Compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, WUXGA, UHD@60hz, Mac
SDTV/EDTV/ HDTV
480i, 576i, 480p, 576p, 720p, 1080i, 1080p, UHD
H-Sync
15.31 102kHz
V-Sync
24 - 30Hz, 47 120 Hz
Environmental
Operation Condition
0° ~ 40°C , 10~85%(No condensing)
Environmental Storage
Condition
-20° ~ 60°C, 5% to 95% (No condensation)
Dimensions
480mm (L) x 400mm (W) x 172mm (H)
Weight
11.5 kg
Light Output
5000lm(Normal)
AC Input
AC Universal 100 240, Typical @ 110VAC (100 240)/+-10%
Power Consumption
580W (Normal), 330W (Eco) , <0.5W (Standby), <2W (Network Standby),
<6.5W (HDBaseT Standby)
Light Source:
Laser-Phosphor
Laser Diode
Audio Speaker
10W x 1
Input Terminals
VGA in x 1
Mini-jack Stereo x 1
HDMI 2.0 x 2
HDBaseT x 1
6 Specifications
– 52 –
Output Terminals
Audio out x 1
USB Type A for 5V/2A power support
3D-Sync x 1
Control Terminals
PC Control(RS-232) x 1
RJ-45 x 1 (10/100Mbps)
USB mini B for service x 1
Security
Security Slot
Security Bar
Note:
For questions regarding product specifications, please contact your local distributor.
For additional information visit:
US: https://www.necdisplay.com/
Europe: https://www.nec-display-solutions.com/
Global: https://www.nec-display.com/global/index.html
For information on our optional accessories, visit our website or see our brochure.
The specifications are subject to change without notice.
6 Specifications
– 53 –
6-2 Projection Distance vs. Projection Size
PJ
Screen Center
Lens Center
Screen Bottom
Throw Distance
L
A
B
a
Screen Right Side
Throw Distance
L
C
PJ
Screen Center
Lens Center
ß
A=Vertical distance between lens center and screen center
B=Vertical distance between lens center and bottom of screen (top of screen for ceiling application)
L=Throw distance
NOTE: Distance may vary +/-5%
6 Specifications
– 54 –
Projection Distance and Size Table
Screen Size
Throw Distance
V Shift
Throw
Ratio
L A B
Diagonal(S)
Width
Height
wide
tele
Lens Shift
MAX
Lens Shift
MIN
Lens Shift
MAX
Lens Shift
MIN
Lens Shift
MAX
Lens Shift
MIN
wide
tele
wide
tele
wide
tele
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
deg
deg
deg
deg
50
1270
44
1107
25
623
48.3
1227
73.1
1857
14.7
374
-14.7
-374
2.5
62
-27.0
-685
16.9
11.4
-16.9
-11.4
1.11
1.68
60
1524
52
1328
29
747
58.3
1480
88.0
2236
17.6
448
-17.6
-448
2.9
75
-32.4
-822
16.9
11.3
-16.9
-11.3
1.11
1.68
70
1778
61
1550
34
872
68.2
1733
102.9
2615
20.6
523
-20.6
-523
3.4
87
-37.8
-959
16.8
11.3
-16.8
-11.3
1.12
1.69
80
2032
70
1771
39
996
78.2
1986
117.9
2994
23.5
598
-23.5
-598
3.9
100
-43.1
-1096
16.8
11.3
-16.8
-11.3
1.12
1.69
90
2286
78
1992
44
1121
88.2
2239
132.8
3373
26.5
672
-26.5
-672
4.4
112
-48.5
-1233
16.7
11.3
-16.7
-11.3
1.12
1.69
100
2540
87
2214
49
1245
98.1
2492
147.7
3752
29.4
747
-29.4
-747
4.9
125
-53.9
-1370
16.7
11.3
-16.7
-11.3
1.13
1.69
120
3048
105
2657
59
1494
118.1
2999
177.6
4510
35.3
897
-35.3
-897
5.9
149
-64.7
-1644
16.6
11.2
-16.6
-11.2
1.13
1.70
150
3810
131
3321
74
1868
148.0
3758
222.3
5647
44.1
1121
-44.1
-1121
7.4
187
-80.9
-2055
16.6
11.2
-16.6
-11.2
1.13
1.70
180
4572
157
3985
88
2241
177.9
4517
267.1
6784
52.9
1345
-52.9
-1345
8.8
224
-97.1
-2466
16.6
11.2
-16.6
-11.2
1.13
1.70
200
5080
174
4428
98
2491
197.8
5024
296.9
7542
58.8
1494
-58.8
-1494
9.8
249
-107.9
-2740
16.6
11.2
-16.6
-11.2
1.13
1.70
240
6096
209
5313
118
2989
237.6
6036
356.6
9058
70.6
1793
-70.6
-1793
11.8
299
-129.4
-3287
16.5
11.2
-16.5
-11.2
1.14
1.70
270
6858
235
5977
132
3362
267.5
6796
401.4
10195
79.4
2017
-79.4
-2017
13.2
336
-145.6
-3698
16.5
11.2
-16.5
-11.2
1.14
1.71
310
7874
270
6863
152
3860
307.4
7808
461.0
11711
91.2
2316
-91.2
-2316
15.2
386
-167.2
-4246
16.5
11.2
-16.5
-11.2
1.14
1.71
100
2540
87
2214
49
1245
98.1
2492
147.7
3752
29.4
747
-29.4
-747
4.9
125
-53.9
-1370
16.7
11.3
-16.7
-11.3
1.13
1.69
※When screen bottom is lower than lens center, B's value is negative.
Screen Size
Throw Distance
H Shift
L C
Diagonal
Width
Height
wide
tele
Lens Shift
MAX(Right)
Lens Shift
MIN(Left)
Lens Shift
MAX(Right)
Lens Shift MIN(Left)
wide
tele
wide
tele
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
deg
deg
deg
deg
50
1270
44
1107
25
623
48.3
1227
73.1
1857
8.7
221
-8.7
-221
10.2
6.8
-10.2
-6.8
60
1524
52
1328
29
747
58.3
1480
88.0
2236
10.5
266
-10.5
-266
10.2
6.8
-10.2
-6.8
70
1778
61
1550
34
872
68.2
1733
102.9
2615
12.2
310
-12.2
-310
10.1
6.8
-10.1
-6.8
80
2032
70
1771
39
996
78.2
1986
117.9
2994
13.9
354
-13.9
-354
10.1
6.7
-10.1
-6.7
90
2286
78
1992
44
1121
88.2
2239
132.8
3373
15.7
398
-15.7
-398
10.1
6.7
-10.1
-6.7
100
2540
87
2214
49
1245
98.1
2492
147.7
3752
17.4
443
-17.4
-443
10.1
6.7
-10.1
-6.7
120
3048
105
2657
59
1494
118.1
2999
177.6
4510
20.9
531
-20.9
-531
10.0
6.7
-10.0
-6.7
150
3810
131
3321
74
1868
148.0
3758
222.3
5647
26.1
664
-26.1
-664
10.0
6.7
-10.0
-6.7
180
4572
157
3985
88
2241
177.9
4517
267.1
6784
31.4
797
-31.4
-797
10.0
6.7
-10.0
-6.7
200
5080
174
4428
98
2491
197.8
5024
296.9
7542
34.9
886
-34.9
-886
10.0
6.7
-10.0
-6.7
240
6096
209
5313
118
2989
237.6
6036
356.6
9058
41.8
1063
-41.8
-1063
10.0
6.7
-10.0
-6.7
270
6858
235
5977
132
3362
267.5
6796
401.4
10195
47.1
1195
-47.1
-1195
10.0
6.7
-10.0
-6.7
310
7874
270
6863
152
3860
307.4
7808
461.0
11711
54.0
1373
-54.0
-1373
10.0
6.7
-10.0
-6.7
100
2540
87
2214
49
1245
98.1
2492
147.7
3752
17.4
443
-17.4
-443
10.1
6.7
-10.1
-6.7
6 Specifications
– 55 –
6-3 Timing Mode Table
Table of Supported Frequency
The unit automatically determines PC signals to select the appropriate resolution. Some signals may require manual
adjustment.
VGA
Signal
Resolution
Aspect Ratio
Refresh Rate
VGA
640 x 480
4:3
60
SVGA
800 x 600
4:3
60
XGA
1024 x 768
4:3
60
WXGA
1280 x 768
15:9
60
WXGA
1360 x 768
16:9 *3
60
Quad-VGA
1280 x 960
4:3
60
SXGA
1280 x 1024
5:4
60
SXGA+
1400 x 1050
4:3
60
WXGA+
1440 x 900
16:10
60
UXGA
1600 x 1200
4:3
60
WSXGA+
1680 x 1050
16:10
60
HD
1280 x 720
16:9
60
Full HD
1920 x 1080
16:9
60
HDMI
Signal
Resolution
Aspect Ratio
Refresh Rate
VGA
640 x 480
4:3
59.94/60/72/75
VGA
720 x 400
9:5
70
SDTV (480p)
720 x 480
4:3/16:9
59.94
SDTV (480i)
720 x 480
4:3/16:9
59.94
SDTV (576i)
720 x 576
4:3/16:9
50
SDTV (576p)
720 x 576
4:3/16:9
50
SVGA
800 x 600
4:3
60/72/75
XGA
1024 x 768
4:3
60/70/75
HDTV (720p)
1280 x 720
16:9
50/59.94/60
WXGA
1280 x 768
5:3
60
Quad-VGA
1280 x 960
4:3
60
SXGA
1280 x 1024
5:4
60
WXGA
1360 x 768
16:9
60
SXGA+
1400 x 1050
4:3
60
WXGA+
1440 x 900
16:10
60
UXGA
1600 x 1200
4:3
60
WSXGA+
1680 x 1050
16:10
60
HDTV(1080i)
1920 x 1080
16:9
50/59.94
HDTV (1080p)
1920 x 1080
16:9
23.94/25/29.97/50/59.94/60
WUXGA
1920 x 1200
16:10
60
4K UHD
3840 x 2160
16:9
23.98/25/29.97/50/59.94
4K2K
4096 x 2160
17:9
23.94/25/29.97/50/59.94
6 Specifications
– 56 –
HDBaseT
Signal
Resolution
Aspect Ratio
Refresh Rate
VGA
640 x 480
4:3
59.94/60/72/75
VGA
720 x 400
9:5
70
SDTV (480p)
720 x 480
4:3/16:9
59.94
SDTV (480i)
720 x 480
4:3/16:9
59.94
SDTV (576i)
720 x 576
4:3/16:9
50
SDTV (576p)
720 x 576
4:3/16:9
50
SVGA
800 x 600
4:3
60/72/75
XGA
1024 x 768
4:3
60/70/75
HDTV (720p)
1280 x 720
16:9
50/59.94/60
WXGA
1280 x 768
5:3
60
Quad-VGA
1280 x 960
4:3
60
SXGA
1280 x 1024
5:4
60
WXGA
1360 x 768
16:9
60
SXGA+
1400 x 1050
4:3
60
WXGA+
1440 x 900
16:10
60
UXGA
1600 x 1200
4:3
60
WSXGA+
1680 x 1050
16:10
60
HDTV(1080i)
1920 x 1080
16:9
50/59.94
HDTV (1080p)
1920 x 1080
16:9
23.94/25/29.97/50/59.94/60
WUXGA
1920 x 1200
16:10
60
4K UHD
3840 x 2160
16:9
23.98/25/29.97/50/59.94
6 Specifications
– 57 –
Table of Supported Frequency For 3D mode
The unit automatically determines PC signals to select the appropriate resolution. Some signals may require manual
adjustment.
True 3D Video Compatibility table
Input
Resolutions
HDMI 1.4a
3D Input
Input timing
1280 X 720P @ 50Hz
Top - and - Bottom
1280 X 720P @ 60Hz
Top - and - Bottom
1280 X 720P @ 50Hz
Frame packing
1280 X 720P @ 60Hz
Frame packing
1920 X 1080i @50 Hz
Side- by-Side (Half)
1920 X 1080i @60 Hz
Side- by-Side (Half)
1920 X 1080P @24 Hz
Top - and Bottom
1920 X 1080P @24 Hz
Frame packing
Note:
3D glasses must be supported to 144Hz.
6 Specifications
– 58 –
6-4 Projector Dimensions
480.0mm [ 18.90" ]
400.0[ 15.75" ]
158.0mm [ 6.22" ]
163.0mm [ 6.42" ]
172.0mm [ 6.77" ]
Appendix I
— 59 —
7 Appendix I
7-1 RS-232C Protocol
RS232 Setting
Baud rate
9600 bps
Data length
8 bit
Parity
No parity
Stop bit
One bit
X on/off
None
Communications procedure
Full duplex
PC Control Code
Function
Code Data
POWER ON
02H 00H 00H 00H 00H 02H
POWER OFF
02H 00H 00H 00H 00H 03H
INPUT SELECT COMPUTER
02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT HDMI1
02H 03H 00H 00H 02H 01H A1H A9H
INPUT SELECT HDMI2
02H 03H 00H 00H 02H 01H A2H AAH
INPUT SELECT HDBaseT
02H 03H 00H 00H 02H 01H BFH C7H
PICTURE MUTE ON
02H 10H 00H 00H 00H 12H
PICTURE MUTE OFF
02H 11H 00H 00H 00H 13H
NOTE: Contact you local dealer for a full list of the PC Control Codes if needed.
7 Appendix I
– 60 –
REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and Mexico)
Please take time to register your new projector. This will activate your limited parts and labor warranty and InstaCare
service program.
Visit our web site at www.necdisplay.com, click on support center/register product and submit your completed form
online.
Upon receipt, we will send a confirmation letter with all the details you will need to take advantage of fast, reliable
warranty and service programs from the industry leader, NEC Display Solutions of America, Inc.
Loading...