Navman ICN600-SMARTST2005 User Manual

iCN 600 series

with Smart

2005

User Manual

iCN 610 iCN 620 iCN 630 iCN 635 iCN 650

English - Europe / Australia / New Zealand

iCN 600 series | User Manual

Contents

Box Contents ............................................................................ 5

1. Introduction ...........................................................................

2. iCN Features ........................................................................

3. Positioning the iCN in a Vehicle ........................................... 10

4. Getting Started. ................................................................... 13

5. Memory Card ...................................................................... 15

6. GPS Status .........................................................................

7. Setting your Destination ...................................................... 17

By Address - Europe and New Zealand .......................... 20

By Address - Australia, Canada and USA ........................ 24

By POI - Europe and New Zealand .................................. 28

By POI - Australia, Canada and USA ............................... 31

8. Using the 2D Map Screen to Plan a Route ......................... 34

9. Multi-stop Trips ................................................................... 35

Europe and New Zealand ................................................ 35

Australia, Canada and USA ............................................. 40

10. Viewing Your Route ............................................................. 46

11. The 2D Map Screen Pop-up Menu ..................................... 51

12. Avoiding an Area ................................................................. 52

13. Route Demonstrator ............................................................ 53

14. Favourites & My Home ........................................................ 55

15. Preferences ......................................................................... 60

16. Smart

 Desktop ................................................................ 71

17. Updating your iCN .............................................................. 72

18. Installing Maps Using Smart

 Desktop ............................. 73

19. Continuous Continental Navigation ..................................... 74

20. Smart Desktop Advanced Features ................................ 76

21. Accessories ........................................................................ 81

Appendix: Street Types ............................................................. 82

Support Information .................................................................. 85

Compliance ............................................................................... 85

iCN 600 series | User Manual

Getting started

Thank you for purchasing this Navman iCN. We hope you enjoy your new GPS transferable navigation system. This User Manual will help you Drive-Away™ with your iCN, straight out of the box.

Navman welcomes your feedback. To contact us or visit our website, see Support Information on page 87.

Box Contents

Purchasers of Smart 2005 software-only upgrade kits, see the enclosed Upgrade Guide for your

Box Contents

iCN with GPS Antenna

12 V In-Vehicle PowerAdaptor with Power-Cable

USB Cable

Protective Carry-Case and Screen-Cleaner

Mounting brackets:

(a) Suction-cup/ballfoot (f) Screw plate * (b) Locking-nut (g) Adhesive tape * (c) Socket-clip (h) Alcohol swab (d) Baseplate

* (i) 3 x Screws *

(e) Retainer ring

* (j) 3 x Screw caps *

* iCN 630, 635, 650 only

Remote Control

(iCN 635, 650 only)

CD-ROMs, including:

• Smart™ 2005 software including Smart Desktop

• Map data

• User Manual (PDF format) & Adobe Reader

Note: The number of disks varies with country of purchase

Documentation, including:

• User Manual

• In-Car Installation Guide

• Software Product Licence

• Limited Warranty Agreement

• Registration Card

AC Power-Pack with Power-Cable

Memory Card

(may not be included)

iCN 600 series | User Manual

Getting started

iCN 600 series | User Manual

Getting started

1. Introduction

Whether you travel in your own country or elsewhere, the iCN will direct you to your destination without the need for map-books and second-hand instructions.

The Global Positioning System (GPS) is available free of charge, at any time, and is accurate to within 5 m (15 ft). Your iCN map provides street-level detail for door-to-door navigation, including Points of Interest (POIs) such as accommodation, petrol stations, railway stations and airports.

Use this guide to learn how to operate your iCN efﬁciently and safely, and discover all the different features available to you.

GPS and GPS Signals

The GPS is a network of satellites that transmit accurate time and position information worldwide. GPS receivers receive signals from these satellites and use the information to determine an exact location. Satellites orbit the earth at around 12,000 miles. While a GPS receiver can detect signals from up to 12 satellites at any time, only three signals are needed to provide a position or “GPS ﬁx” (latitude and longitude) for vehicle navigation systems.

The iCN GPS antenna receives GPS signals. To receive GPS signals, ensure that the iCN is outdoors, or in a vehicle outdoors, and the GPS antenna has an unobstructed view of the sky. The iCN can operate in all weather types except snowfall.

For more information about GPS and your iCN, see page 16.

Safety Notice

WARNING: In a vehicle, it is your sole responsibility to place, secure and use the ICN in a manner

that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe driving practices. It is your responsibility to read and follow the vehicle mount installation instructions and to use the product consistent with your government’s laws/regulations. Consult the vehicle manual to ensure the mounting location is safe.

It is your sole responsibility to adhere to the following safety instructions at all times:

• Do not operate the ICN while driving or place the ICN in a position that obstructs the driver’s view.

• Do not mount the ICN in a way that may be distracting or interfere with the safe operation of the vehicle, the deployment of airbags or other safety equipment.

• Do not leave the ICN in view while your vehicle is unattended, especially in strong or direct sunlight.

• Do not use or handle the ICN when it is hot; leave it to cool, out of direct sunlight.

Failure to adhere to these instructions may lead to serious personal injury, including death, or property damage. Navman disclaims all liability for use of the iCN that contributes to injuries, death, property damage or violates law.

iCN 600 series | User Manual

Getting started

3 4

2. iCN Features

We recommend that you familiarize yourself with the iCN’s basic operations, such as using the

8-way toggle and

Volume button.

Some buttons have two functions, and speciﬁc features vary between iCN models.

Front Components

Component Description

1 Screen Displays maps and menu options

2 Infrared Receiver* Receives signals from the remote control

3 OK Conﬁrms the selected menu option, text or preference

4 Zoom/Brightness

Changes the amount of map area shown, or press and hold to adjust the screen brightness

5 ESC

Cancels an action, returns to the previous screen or deletes the last text character on the Keyboard screen; hold down for longer to delete a whole line at once.

6 8-Way Toggle

Selects Main Menu options, keyboard characters and Preferences, moves around the 2D Map screen to select a destination, and scrolls through lists, such as lists of search results.

7 Page

Cycles through the 2D Map, 3D Map

**, Next Turn and Next 4 Turns

screens; displays additional preference or search-result screens, when available.

8 Volume

Broadcasts the next voice-guidance instruction and adjusts voiceguidance volume.

9 Menu/Power

Displays the Main Menu screen and turns the iCN on and off.

* iCN 610, 635 and 650 only. ** iCN 630, 635 and 650 only.

iCN 600 series | User Manual

Getting started

Back Components

Component Description

1 Speaker

Broadcasts voice commands and warnings; Use Volume button to adjust

2 Memory Card Slot*

Memory card may be inserted into slot with label facing the front of the iCN.

3 GPS Receiver

Receives signals from GPS satellites when lifted out to the horizontal position

External Antenna Socket

Connection socket for GPS MCX External Anntenna (not included)

5 Power Socket Connection socket for AC Power-Pack or In-Vehicle Power Adaptor

6 USB Socket Connection socket for USB cable to your computer

* iCN 650 does not have a Memory Card Slot and does not require a memory card.

Remote Control

Button functions are the same as the iCN control buttons except that the iCN cannot be turned on using the Remote Control.

The remote control is:

• only included with the iCN 635 and iCN 650,

• available for the iCN 610 as an accessory,

• is not compatible with the iCN 620 or iCN 630.

iCN 600 series | User Manual

Getting started

3. Positioning the iCN in a Vehicle

The iCN can be mounted in a vehicle two ways:

1. By suction on the windscreen;

2. By suction, adhesive tape and screws drilled directly into the dashboard. Note: This is a permanent solution and will mark your dashboard.

Follow the safety guidelines on page 7 to ensure that the iCN does not obstruct the driver’s view, or interfere with the operation of vehicle airbags and safety devices.

Suction Mount

Assembling the iCN Suction-Mount

Choose a position on the windshield that is clearly visible to the driver without obstructing the view of the road.

1. Assemble the suction-mount:

• Slip the locking-nut over the ballfoot.

• Snap the socket-clip onto the ballfoot.

• Screw the locking-nut onto the thread of the socket-clip until ﬁrm.

2. Use the alcohol swab to clean and dry the suction-cup and the mounting-area on the windshield, then attach the suction-mount to the windshield:

a. Hold the suction-cup ﬁrmly against the windshield and b. Press the lever towards the suction-cup.

a b

Click

iCN 600 series | User Manual

Getting started

Inserting the iCN into the Suction-Mount

3. Open the GPS antenna outwards, so that it has a clear view of the sky.

4. iCN 650 users, United States, Canada and New Zealand users go to step 5,

otherwise continue:

Gently insert the card in the Memory Card slot with the label facing the front of the iCN.

(see page 15 for how to insert the memory card).

Note: Before inserting the memory card for the first time, remove the plastic space-saver

from the Memory Card slot:

gently push down on the top edge of the space-saver to

release it, and pull it out of the slot

5. Insert the iCN into the suction-mount:

a. Position the two locating-tabs on the underside of the iCN into the corresponding

slots on the socket-clip.

b. Snap the upper side of the iCN into the socket-clip.

6. Connect the iCN to the vehicle power supply:

a. Plug the small end of the In-Vehicle Power-Adaptor into the Power Socket on the left

side of the iCN.

b. Plug the other end of the In-Vehicle Power-Adaptor into the 12 V vehicle power-socket.

7. Press

for one second.

The iCN will turn on.

a b

* Not iCN 650, United States, Canada or New Zealand users.

iCN 600 series | User Manual

Getting started

Adhesive Tape and Screw-Mount*

You can use the baseplate, adhesive tape and screws supplied to permanently mount the iCN directly into the vehicle dashboard.

Note: This is a permanent solution. Once fixed, the adhesive tape cannot be removed.

*iCN 630, 635, 650 only

Assembling the iCN Screw-Mount

1. Choose a position on the dashboard where the iCN will be clearly visible to the driver, and ensure that the mounting surface is clean and dry.

2. Remove the protective layer from the tape and press down ﬁrmly for 30 seconds.

3. Press the suction-cup ﬁrmly against the surface and press the lever down.

4. Use the baseplate and screws supplied to ﬁx the iCN base into the dashboard.

5. Slip the locking-nut over the ballfoot, with the ﬂat side facing upwards.

6. Snap the socket-clip onto the ballfoot.

7. Screw the locking-nut onto the thread of the socket-clip until ﬁrm.

Inserting the iCN into the Screw-Mount

1. Snap the iCN onto the socket-clip. Position the two locating-tabs on the underside of the iCN into the corresponding slots on the socket-clip. Then push the iCN into the clip.

2. Open the GPS antenna outwards, so it has a clear view of the sky.

3. Plug the power-cable into the socket on the left side of the iCN and the other end into the 12 V vehicle power-socket.

iCN 600 series | User Manual

Getting started

4. Getting Started

The Main Menu screen provides access to all of the iCN’s functions, including navigating to a destination.

Step One: Turn iCN On

1. Plug the power adapter into the socket on the left of the iCN and the other end into the 12 V vehicle power-socket.

2. Gently pull the bottom of the GPS receiver away from the iCN. The receiver will lift out to a horizontal position to allow it to obtain a GPS ﬁx.

3. Press for one second. The iCN will turn on and display the Language screen.

Step Two: Language Screen

1. Use the 8-way toggle to choose your language, then press OK.

• To prevent the Language screen from displaying on each startup, use the 8-way toggle to select the Do not show on startup check box, then press OK

2. Press

to go to the next screen.

The Warning screen will display.

iCN 600 series | User Manual

Getting started

Step Three: Warning Screen

1. Read the warning message.

2. Select Accept, then press OK to conﬁrm that you understand. The ﬁrst

Tutorial screen will display.

Step Four: Tutorial Screens

1. Read the Tutorial screen.

• To prevent the Tutorial from displaying on startup, use the 8-way toggle to select the Do not show Tutorial on startup check box, then press OK

2. Press

to move through each Tutorial screen.

The Main Menu screen will display.

Main Menu Screen

• Use the 8-way toggle to select a Main Menu option; conﬁrm a selection by pressing OK.

• Return to the Main Menu screen at any time by pressing .

• The Route Information option is only available when a route has been calculated. See pages 49-50

for more information.

To Turn iCN Off

1. Gently push the GPS receiver back towards the iCN. The receiver will click into place.

2. Complete one of the following:

• iCN 610, 620, 650: Press for three seconds. When the conﬁrmation message displays, select Yes, then press OK. The iCN will turn off.

• iCN 630, 635: Press for three seconds until the iCN turns off.

iCN 600 series | User Manual

Getting started

5. Memory Card

iCN 610, 620, 630 and 635

Your iCN comes with a memory card contaning a preactivated map*. To navigate to your destination you must ﬁrst insert the memory card into your iCN.

To navigate in an area outside of the preactivated map, you must ﬁrst purchase a Map Product Key from your Navman supplier. Install Smart

 Desktop, then use it to activate your Map Product Key

and install the required map. For more information on installing maps, see page 73.

* If you purchased your iCN 635 in New Zealand, you will not receive a memory card as the internal

memory contains a preactivated map of New Zealand.

Inserting Memory Card

Note: Before inserting the memory card for the first time, remove the plastic space-saver from the Memory Card slot

: gently push down on the top edge of the space-saver to release it,

and pull it out of the slot

Before inserting the memory card, turn off the iCN. Next, gently insert the card in the Memory Card slot with the label facing the front of the iCN.

Removing Memory Card

Before removing the memory card, turn off the iCN. Next, gently push down on the top edge of the card to release it, and pull it out of the slot.

iCN 650

The iCN 650 contains all preactivated maps for Western Europe or Continental US/Canada in internal memory and does not come with a memory card slot.

iCN 600 series | User Manual

Getting started

6. GPS Status

Signals are transmitted by Global Positioning System (GPS) satellites orbiting the Earth. You can view your GPS status at any time from the 2D Map, 3D Map*, Next Turn and Next 4 Turns screens.

The GPS Strength Indicator

will display green when there is a valid ﬁx (2D or 3D), and between one and three bars will display to indicate the strength of the signal; the GPS Strength Indicator will display red when no ﬁx is available.

For more detailed information on your current GPS fix, see GPS Status on page 69.

* iCN 610, 620 will display the 2D Navigation Map screen.

iCN 600 series | User Manual

Getting started

7. Setting Your Destination

For your safety, enter destination information before you start a journey.

Do not operate the iCN while driving

Select a destination using the Destination, Keyboard and Preview screens, which used together form a destination wizard.

This section describes how to use each of these screens and provides two case studies to help guide you through setting your destination.

Destination Screen

The Destination screen is used to select your destination by area, street, postal code/ZIP code, Point of Interest (POI), intersection, city, town, country or state.

As you specify each part of the address, it will display in the You are going to ﬁeld at the top of the screen. The available options will change to reﬂect the parts of the address still to be completed.

• Use the 8-way toggle to move around the Destination screen.

• To select an option, press OK

Keyboard Screen

The Keyboard screen will display when you are required to enter text, such as when searching for a street name. As you select each character, the ﬁrst two results will display. Press

to see more search results. Search results will be listed in matching order, with the closest matches appearing at the top of the list.

The Keyboard screen can display in three modes: alphabet, alternate and number/symbol.

Figure 1. Alphabet Keyboard Figure 2. Alternate Keyboard

iCN 600 series | User Manual

Getting started

Figure 3. Number/Symbol Keyboard

As you select each character, the ﬁrst two results will display. Press

to see more search results.

• Use the 8-way toggle to move around the Keyboard screen.

• To select a character or a search result, press OK.

• To delete a character, press ESC or select <<, then press OK.; hold ESC to delete the line.

• To display the number/symbol Keyboard screen (Figure 3), select 123, then press OK

• To display the alternate Keyboard screen (Figure 2), press

, or select Alt, then press OK.

• To display the alphabet Keyboard screen (Figure 1), press

, or select ABC, then press OK.

Preview Screen

The Preview screen is used to display a preview of your destination before navigating to it, saving it as a Favourite or displaying it on the 2D Map screen.

• Use the 8-way toggle to move around the Preview screen.

• To display a smaller area in greater detail, press

• To display a larger area in less detail, press

• To display your destination on the 2D Map screen, select the preview map, then press OK. The 2D Map screen will display.

• To save your destination as a Favourite, select Save, then press OK. The New Favourite screen will display. See Favourites & My Home on page 36.

• To calculate the route and open the 3D Map screen*, select Go, then press OK

The 3D Map screen* will display.

• To view Point of Interest (POI) details when your destination is a POI, select

, then press OK.

The POI Detail screen will display.

* iCN 610, 620 will display the 2D Map screen.

iCN 600 series | User Manual

Getting started

Address Search Rules

The following rules apply when searching for a destination in Europe:

Street Names with Dates

If a street name contains a date or a number, search by the ﬁrst number:

Example 1: If searching for “Faubourg du 13 Juillet 1920”, search by “13”. Example 2: If searching for “Avenue du 14 Avril 1914”, search by “14”. Example 3: If searching for “Rue de la 1 ere Arm

ée”, search by “1”.

Streets Named After People (excluding Italy)

If a street name is a person’s name (including at least a ﬁrst and last name), search by the ﬁrst name:

Example 1: If searching for “Rue Albert Mathieu”, search by “Albert”. Example 2: If searching for “Fred Archer Way”, search by “Fred”. Example 3: If searching for “Franz Grillparzer-Strasse”, search by “Franz”.

Streets Named After People - Italy

In Italy, if a street name is a person’s name (including at least a ﬁrst and last name), search by the last name:

Example 1: If searching for “Via de Angelo de Thomasis”, search by “Thomasis”. Example 2: If searching for “Via Placido Giovanella”, search by “Giovanella”. Example 3: If searching for “Via della Giacomo Marca”, search by “Marca”.

Postcodes in United Kingdom and Netherlands

When searching by postcode in United Kingdom or Netherlands, type the postcode with spaces and without the last two letters.

Example 1: If searching for “RH6 9ST”, search by “RH6 9”. Example 2: If searching for “3514 BN”, search by “3514”.

For exact European street type abbreviations, see Appendix: Street Types on page 82.

iCN 600 series | User Manual

Getting started

Setting Your Destination by Address -

Case Study One: Europe and New Zealand

This case study will show you how to set your destination by selecting your country, then area, then street, then house number.

Note: This case study applies to Europe and New Zealand only. For navigating in Australia, Canada and USA, see page 24.

Step One: Open the Destination screen

a. From the Main Menu, select Go To, then press OK. b. From the Go To screen, select Address or POI, then press OK.

The Destination screen will display.

Important Note: If this is the first time you are setting your destination and you have maps from more than one country installed and selected, then the Select Country

screen will

display instead of the Destination screen. Go directly to Step Two: Select the Country of

Destination, step b

The next time you perform this procedure, the Destination screen will open as expected.

Step Two: Select the Country of Destination

If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to Step Three: Find the Area of Destination

a. From the Destination screen, select Change country, then press OK.

The Select country screen will display.

b. Select a country using the 8-way toggle. Press OK to select from the list.

The Destination screen will display.

iCN 600 series | User Manual

Getting started

Step Three: Find the Area of Destination

a. From the Destination screen, select Find area, then press OK.

The Keyboard screen will display.

b. Use the Keyboard screen to ﬁnd the area of your destination.

For information on using the Keyboard screen, see pages 17-18

The Destination screen will display.

Step Four: Find the Street of Destination

a. From the Destination screen, select Find street, then press OK.

The Keyboard screen will display.

iCN 600 series | User Manual

Getting started

b. Use the Keyboard screen to ﬁnd the street of your destination. For information on using

the Keyboard screen, see pages 17-18. The Destination screen will display.

Step Five: Find the House Number of Destination

a. From the Destination screen, select Enter house number, then press OK.

The Keyboard screen will display.

Note: If Enter house number option is not displayed, house numbers are not available for your selected street. Select Go to centre of street, then press OK to display the Preview screen. Go to step

iCN 600 series | User Manual

Getting started

b. Use the Keyboard screen to ﬁnd the house number of your destination. For information

on using the Keyboard screen, see pages 17-18.

The Preview screen will display.

c. Complete one of the following:

• To calculate the route and open the 3D Map screen*, select Go, then press OK. The 3D Map screen

* will display.

• To display the destination on the 2D Map screen, select the preview map, then press OK

The 2D Map screen will display.

• To save the destination as a Favourite, select Save, then press OK. The New Favourite screen will display. See Favourites & My Home on page 36.

• To change your destination, press ESC. The Destination screen will display.

* iCN 610, 620 will display the 2D Navigation Map screen.

To return to the Main Menu, press .

iCN 600 series | User Manual

Getting started

Setting Your Destination by Address -

Case Study Two: Australia, Canada & USA

This case study will show you how to set your destination by selecting your country, then state, then town or city, then street, then house number.

Note: This case study applies to Australia, Canada and USA only. For navigating in Europe and New Zealand, see page 20.

Step One: Open the Destination screen

a. From the Main Menu, select Go To, then press OK. b. From the Go To screen, select Address or POI, then press OK.

The Destination screen will display.

Important Note:

i. If this is the first time you are setting your destination and you have maps from more than

one country installed and selected, then the Select Country

screen will display instead of

the Destination screen. Go directly to Step Two: Select the Country of Destination,

step b.

The next time you perform this procedure, the Destination screen will open as expected.

ii. If this is the first time you are setting your destination and you have maps from only one

country, but more than one state installed and selected, then the Select State

screen will

display instead of the Destination screen. Go directly to Step Three: Select the State

of Destination

The next time you perform this procedure, the Destination screen will open as expected.

Step Two: Select the Country of Destination

If you only have the map of one country installed and selected, that country is selected for your destination by default and cannot be changed. Go to Step Three: Select the State of

Destination

a. From the Destination screen, select Change country or Change country or state then

press OK. The Select country screen will display.

b. Select a country using the 8-way toggle. Press OK to select from the list.

The Select state screen will display.

• If you only have the map of one state installed and selected, that state is selected for

your destination by default. Go to Step Four: Find the Town or City of Destination

iCN 600 series | User Manual

Getting started

Step Three: Select the State of Destination

If you only have the map of one state installed and selected, that state is selected for your destination by default and cannot be changed. Go to Step Four: Find the Town or City of Destination.

a. Select a state using the 8-way toggle. Press OK to select from the list.

The Destination screen will display.

Step Four: Find the Town or City of Destination

a. From the Destination screen, select Find town/city, then press OK.

The Keyboard screen will display.

b. Use the Keyboard screen to ﬁnd the town or city of your destination. For information on

using the Keyboard screen, see pages 17-18

The Destination screen will display.

iCN 600 series | User Manual

Getting started

Step Five: Find the Street of Destination

a. From the Destination screen, select Find street, then press OK.

The Keyboard screen will display.

b. Use the Keyboard screen to ﬁnd the street of your destination. For information on using

the Keyboard screen, see page

s17-18.

The Destination screen will display.

Step Six: Find the House Number of Destination

a. From the Destination screen, select Enter house number, then press OK.

The Keyboard screen will display.

Note: If Enter house number option is not displayed, house numbers are not available for your selected street. Select Go to centre of street, then press OK to display the Preview screen. Go to step

iCN 600 series | User Manual

Getting started

b. Use the Keyboard screen to ﬁnd the house number of your destination. For information

on using the Keyboard screen, see pages 17-18.

The Preview screen will display.

c. Complete one of the following:

• To calculate the route and open the 3D Map screen*, select Go, then press OK. The 3D Map screen

* will display.

• To display the destination on the 2D Map screen, select the preview map, then press

The 2D Map screen will display.

• To save the destination as a Favourite, select Save, then press OK. The New Favourite screen will display. See Favourites & My Home on page 36.

• To change your destination, press ESC. The Desintation screen will display.

* iCN 610, 620 will display the 2D Navigation Map screen.

To return to the Main Menu, press .

+ 61 hidden pages