PLEASE READ CAREFULLY BEFORE INSTALLING PRODUCT IN VEHICLE
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
Removing original equipment, adding accessories or modifying your vehicle could affect the vehicle’s safety or
make it illegal to operate in some jurisdictions.
Follow all product instructions and all instructions in your vehicle owner’s manual regarding accessories or
modifications.
Consult your country’s and/or state’s laws regarding operation of a vehicle with any accessories or
modifications.
It is your sole responsibility to place, secure and use your Navman in a manner that will not cause accidents,
personal injury or property damage. Always observe safe driving practices.
Do not mount your Navman in a way that may interfere with the safe operation of the vehicle, the deployment
of air bags or other safety equipment.
Do not operate your Navman while driving.
Before you use your Navman for the first time, familiarize yourself with your device and its operation.
On main roads, the distance to an exit calculated by your Navman may be further than the distance shown on
road signs. Road signs show the distance to the start of an exit while your Navman shows the distance to the
next intersection, i.e., the end of the exit ramp or road. To prepare to exit a road, always follow distance
information on road signs.
The use of information regarding safety or speed camera locations may be subject to local laws in the country
of use. You are responsible for checking that you can legally use the information in your country or in the
country where the information will be used.
safety messages that follow this symbol to avoid possible injury or death.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTION used without the safety alert symbol indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Do not handle your Navman while it is hot. Let the product cool, out of direct sunlight.
Do not expose your Navman to direct sunlight in an unattended vehicle for prolonged periods. Overheating
may damage the unit.
Note: To discourage theft, do not leave the Navman, its mounting bracket or any cables in plain view in an unattended vehicle.
2
Home Charger-specific safety information
To charge your Navman from the mains power, use the home charger supplied by Navman as an accessory
(may be sold separately). Using other home chargers with your Navman could result in serious injury or
property damage.
Never use the charger if the plug or cord is damaged.
Do not expose the charger to moisture or water. Do not use the charger in a high moisture environment.
Exposure to water may cause electrical sparks or fires.
Never touch the charger when your hands or feet are wet.
Allow adequate ventilation around the charger when using it to operate your Navman or charge the Navman
internal battery. Do not cover the charger with paper or other objects that will reduce ventilation. Do not use
the charger while it is inside a carrying case or other container.
Ensure that the charger is connected to a power source with the correct fitting and voltage requirements. The
voltage requirements can be found on the home charger casing and/or packaging.
Do not attempt to service the charger as this could result in personal injury. Replace the charger if it is damaged
or exposed to excess moisture.
Internal battery-specific safety information
Your Navman contains a non-replaceable internal lithium-ion polymer battery. The battery may burst or
explode if mishandled, releasing hazardous chemicals. To reduce the risk of fire or burns, do not disassemble,
crush or puncture the battery.
Recycle or dispose of the battery safely and properly according to local laws and regulations. Do not dispose of
the battery in fire or water.
Only use the correct home charger (sold separately) or in-car charger supplied by Navman to charge the
internal battery. Only use the installed internal battery with the Navman unit.
The battery will stop charging when the ambient temperature is less than 0ºC (32ºF) or more than 40ºC
(104ºF).
Failure to adhere to these warnings and cautions may lead to death, serious injury or property damage.
Navman disclaims all liability for installation or use of the Navman that causes or contributes to death,
injury or property damage or that violates any law.
Warning Notice to Drivers in the United States
State law may prohibit drivers in states such as Arizona, California and Minnesota from mounting objects on
their windshields while driving. Please make sure you research and follow your most current State laws. An
alternative mounting option is provided in the box with your product, also, stores offer additional mounting
alternatives. Navman does not take any responsibility for any fines, penalties, or damages that may be incurred
as a result of disregarding this notice.
3
Caring for your Navman
Taking good care of your Navman will ensure trouble-free operation and reduce the risk of damage to your
Navman.
Keep your Navman away from excessive moisture and extreme temperatures.
Avoid exposing your Navman to direct sunlight or strong ultraviolet light for extended periods of time.
Do not place anything on top of your Navman or drop objects on your Navman.
Do not drop your Navman or subject it to severe shock.
Do not subject your Navman to sudden and severe temperature changes. This could cause moisture
condensation inside the unit, which could damage your Navman. In the event of moisture condensation,
allow your Navman to dry out completely before use.
The screen surface can easily be scratched. Avoid touching it with sharp objects. Non-adhesive generic
screen protectors designed specifically for use on portable devices with LCD panels may be used to help
protect the screen from minor scratches.
Never clean your Navman with it powered on. Use a soft, lint-free cloth to wipe the screen and the
exterior of your Navman.
Do not use paper towels to clean the screen.
Never attempt to disassemble, repair or make any modifications to your Navman. Disassembly,
modification or any attempt at repair could cause damage to your Navman and even bodily injury or
property damage and will void any warranty.
Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your
Navman, its parts or accessories.
4
Contents
Important safety information .......................................................................................................................... 2
Home Charger-specific safety information ..............................................................................................3
Internal battery-specific safety information ............................................................................................3
Warning Notice to Drivers in the United States...................................................................................... 3
Caring for your Navman............................................................................................................................... 4
Important information for using the manual ...........................................................................................8
How do I install my Navman?.......................................................................................................................... 9
Turning on and off ....................................................................................................................................... 13
Shutdown and hardware reset .................................................................................................................. 13
How do I monitor the battery status?..................................................................................................... 13
How do I charge the battery?.................................................................................................................... 13
Charging the battery via the USB cable (sold separately)...................................................................14
Navigating on the screen ........................................................................................................................... 15
How do I adjust the volume? .................................................................................................................... 15
How do I get started?...................................................................................................................................... 16
How do I turn my Navman on for the first time?..................................................................................16
What are the main screens I will use? ..........................................................................................................18
Main Menu screen ........................................................................................................................................ 18
How do I navigate with GPS?.........................................................................................................................20
How does my Navman receive GPS signals?..........................................................................................20
How do I view my GPS status? .................................................................................................................20
How do I go from A to B? ............................................................................................................................... 21
What if I miss a turn?.................................................................................................................................. 21
How do I search for an address?...............................................................................................................22
Case Study: How do I search for an address? ....................................................................................22
Using the Keyboard screen....................................................................................................................24
Using the Destination Search screen ....................................................................................................24
How do I create a trip with multiple stops? ...........................................................................................26
Case Study: How do I navigate to multiple addresses? ...................................................................26
How do I skip a waypoint during a multi-stop trip?.........................................................................29
How do I search for a Point of Interest (POI)?.......................................................................................30
Case Study: How do I search for a Point of Interest?.......................................................................30
How do I save Favourites and My Home?....................................................................................................33
Can I save a NavPixTM to a Favourite?......................................................................................................33
How do I save a Favourite or My Home? ................................................................................................33
How do I navigate to a Favourite?............................................................................................................34
How do I navigate to My Home?..............................................................................................................34
5
Option 1 - Via the Main Menu ..............................................................................................................34
Option 2 - Via the Favourite Destinations screen..............................................................................34
How do I edit the name of a Favourite?..................................................................................................35
How do I delete a Favourite?.....................................................................................................................36
How do I navigate to a recent location?......................................................................................................37
How do I view my route?................................................................................................................................38
3D Map screen..............................................................................................................................................38
How do I use the Map Menu?................................................................................................................... 48
Displaying the Map Menu ..................................................................................................................... 48
Map Menu options.................................................................................................................................. 48
How do I avoid an area?.............................................................................................................................49
How do I add an Avoid Area?................................................................................................................49
How do I delete an Avoid Area?...........................................................................................................49
How do I delete all Avoid Areas? .........................................................................................................49
How do I preview a route?..............................................................................................................................50
How do I view my route statistics?............................................................................................................... 51
How do I view statistics on my current route? ......................................................................................51
How do I view statistics of my trips to date?.........................................................................................52
How do I view my trip logs? ......................................................................................................................53
How do I use NavPixTM? ............................................................................................................................54
How do I manage my NavPixTM?.........................................................................................................54
Album management...............................................................................................................................54
What can I customise? ....................................................................................................................................67
POI Alerts...................................................................................................................................................... 72
Resetting your GPS fix ...........................................................................................................................72
Setting your GPS mode..........................................................................................................................72
Language .......................................................................................................................................................72
Units 1/2 ...................................................................................................................................................72
Units 2/2................................................................................................................................................... 72
Saved Info .....................................................................................................................................................72
About .............................................................................................................................................................72
Point of Interest categories........................................................................................................................72
Branded Points of Interest.....................................................................................................................72
Point of Interest categories by Navman.............................................................................................72
Point of Interest categories by subscription ......................................................................................72
Traffic and other TMC Events.................................................................................................................... 72
Safety Camera POIs ....................................................................................................................................72
For more information ......................................................................................................................................72
Safety camera information ...................................................................................................................72
Thank you for purchasing this Navman. This manual has been prepared to guide you through the operation of
your Navman from first set-up through to continuous use. Please read this manual carefully before using your
Navman for the first time. Keep this manual in a safe place and use as your first point of reference.
Important information for using the manual
It is important to understand the terms and typographical conventions used in this manual.
Formatting
The following formatting in the text identifies special information:
Convention Type of Information
Bold Navman components or items displayed on screen, including buttons, headings, field names and options.
Italics Indicates the name of a screen.
Terms
The following terms are used throughout this manual to describe user actions.
Term Description
Tap Press and release an item displayed on the touch screen.
Tap and hold Tap and hold an item displayed on the touch screen for 2-3 seconds.
Select Tap an item in a list or tap a command from a menu.
8
How do I install my Navman?
CAUTION:
Select an appropriate location for mounting the Navman in a vehicle. Never place the Navman where the driver’s field
of vision is blocked.
If the car’s windscreen is tinted with a reflective coating, it may be athermic and impact the GPS reception. In this
instance, please mount your Navman where there is a “clear area.”
To protect your Navman against sudden surges in current, connect the car charger only after the car engine has been
started.
F35/F37M Installation
1
2
3
4
9
F45/F47M Installation
1
3
2
4
Receiving TMC information
Note: Not available on all models.
You can receive current traffic information on your Mio via an optional traffic accessory. To receive traffic
information, you must connect your Navman to the in-car charger.
TMC information is monitored by the navigation software. Once the information is received, you can view it on
your device and traffic icons will appear in the map view. Certain roads with reported traffic will be highlighted
and you can choose to avoid those roads and an alternate route will be automatically calculated. For more
information, see “
How does my Navman receive traffic information?” on page 61.
10
Getting to know your Navman
F35/F37M
Power Switch
n
Socket for in-car charger, USB cable
o
(sold separately), home charger (sold
separately) and TMC accessory kit (may
be sold separately)
p
q
Speaker
Cradle Socket
11
F45/F47M
Power Switch
n
Socket for in-car charger, USB cable
o
(sold separately), home charger (sold
separately) and TMC accessory kit (may
be sold separately)
p
q
Cradle Socket
Speaker
12
Turning on and off
For normal operation, turn off your Navman by sliding the power switch to the OFF position. Your Navman
enters a suspended state. To use it again, slide the power switch to the ON position. Your Navman will be back
to where you left off.
F35/F37M F45/F47M
Shutdown and hardware reset
Occasionally, you may need to perform a hardware reset if your Navman stops responding; or appears to be
“frozen” or “locked-up.”
You can perform a hardware reset by shutting down your Navman and then turning it back on. To shut down
your Navman, slide the power switch to the RESET position. To turn on your Navman after shutting it down,
slide the power switch to the ON position.
NOTE: Switching to the Reset position turns the battery off. It is recommended you move the switch to this position if you are
planning to store your Navman for any length of time.
How do I monitor the battery status?
Your Navman has an internal battery that when fully charged, should provide power for up to 3 hours.
You can monitor battery power status on the Power screen.
Note: The battery may not be fully charged when you use your Navman for the first time.
To access the Power screen, tap .
How do I charge the battery?
The Battery Status bar displays External Power while the battery is charging; when the battery is fully charged,
the Battery Status bar will display at 100%.
To charge your Navman in a vehicle, plug the in-vehicle charger to the bottom of your Navman and
the other end into the vehicle power socket, as shown in the” How do I install my Navman?” section.
To charge your Navman using your computer, see later section for details.
To charge your Navman using a mains power socket, plug the mains power charger cable to the
bottom of your Navman and the mains power charger pack into the mains power socket.
Note: The mains power charger is not included with all models and may be purchased separately.
13
Charging the battery via the USB cable (sold separately)
If you intend to charge your Navman in this way, turn off your Navman so that it takes less time to charge the
battery.
1. Turn on the computer.
2. Connect the mini-USB end of the USB cable to the
USB port on your computer.
F35/F37M F45/F47M
Note: If your Navman is on when connected to a computer, a screen appears to prevent you from using your Navman.
Note: When the Navman is connected to a computer, it is recognized as an external mass storage device. Do not delete any
files pre-installed in the Navman. Deleting files of which the function is unknown can cause programs or features to
malfunction.
CAUTION: For optimal performance of the lithium battery:
Do not charge the battery where the temperature is high (e.g. in direct sunlight).
There is no need to fully discharge the battery before charging. You can charge the battery before it is discharged.
When storing the product for a long period of time, be sure to fully charge the battery at least once every two weeks.
Over discharge of the battery can affect the charging performance. Switching the power to Reset will prolong the
battery life if you don't plan to use your Navman for a long period of time.
bottom of your Navman and the other end to a
14
Navigating on the screen
To operate your Navman, touch the screen with your fingertip. You can perform the following actions:
F35/F37M F45/F47M
Tap
Touch the screen once with your fingertip to open items or select onscreen buttons or options.
Drag
Hold your fingertip on the screen and drag up/down/left/right or across the screen. (This is not supported
by all applications.)
Tap and hold
Tap and hold your fingertip until an action is complete, or a result or menu is shown. (This is not supported
by all applications.)
How do I adjust the volume?
The volume on your Navman can be adjusted by the volume control on the Volume preference screen.
To mute the volume from the map screens, tap
and then tap . Tap and hold a bit longer allows
you to shortcut directly to the volume screen.
For more information on how to adjust the volume on your Navman, see “
Volume” on page 77.
15
How do I get started?
Note: The first time you use your Navman, it may take up several minutes to establish a GPS connection. For more information
about GPS, refer to the GPS Frequently Asked Questions guide on the enclosed DVD.
How do I turn my Navman on for the first time?
To get started for the first time, complete the following steps:
1. Read the Important Safety Information on page
2. Position your Navman
Follow the instructions on page
Note: Ensure that your Navman does not obstruct the driver's view, or interfere with the operation of the vehicle airbags
and safety devices.
9.
3. Turn your Navman on
Your Navman will turn on and display the Language screen.
4. Select your preferred language
From the Select Language screen, tap your preferred language.
2.
To prevent the Select Language screen from displaying on each start-up, clear the Show on start-up
check box.
You can change your preferred language while using your Navman, see “Language” on page 82.
5. Read the warning message
a) The Safety Agreement screen will display after you have selected your preferred language.
Read the Safety Agreement message.
b) To confirm that you have read and understood the message, tap Accept.
The Tutorial will display.
6. View the Tutorial
When you have accepted the Safety Agreement, the first Tutorial screen will display.
To prevent the Tutorial from displaying again on start-up, clear the Show tutorial on start-up check
box.
To move forward through the Tutorial screens, tap .
To view the previous screen, tap
To view the Tutorial again while using your Navman, see “Tutorial” on page 92.
Note: If you have maps installed from multiple continents, you may be prompted to select the maps you require. To use
maps from a different continent at a later time, you can select a different map via the Select Map screen in the Select Map 3/3 preferences; refer to page
75.
.
16
When you have finished the Tutorial, the 3D Map screen will display. If you have a GPS fix, your current location
will be displayed on the map.
17
What are the main screens I will use?
Main Menu
screen
The Main Menu screen is your starting point for searching for a destination. The Main Menu screens also allow
you to enter an address for your destination and customise preferences.
The Main Menu can be accessed from the map screens by tapping
bottom of any screen.
or by tapping the status bar at the
Note: The Main Menu screens may differ from those displayed above, depending on your Navman model.
Map screens
There are five map screens used to view the route to your destination:
3D Map
2D Map
Traffic Overview (Not available on all models)
Route Overview
Turn-by-Turn™
The Map screens can be accessed from the Main Menu screen by tapping
You can cycle through the different map screens by tapping
on any map screen (the name of the map
screen will display briefly as your cycle through).
18
.
For more information on the map screens, see “How do I view my route?” on page 38.
For information on using the Map menu from the 3D Map and 2D Map screens, see “How do I use the Map
Menu?” on page
48.
19
How do I navigate with GPS?
The Global Positioning System (GPS) is available at any time, free of charge, and is accurate to within 5m (15ft).
GPS navigation is made possible by a network of satellites that orbit the Earth at around 20,200km (12,552mi).
Each satellite transmits a range of signals which are utilised by GPS receivers, such as your Navman, to
determine an exact location. Although a GPS receiver can detect signals from up to 12 satellites at any time,
only four signals are required to provide a position or “GPS fix” (latitude and longitude), for vehicle navigation
systems.
How does my Navman receive GPS signals?
Your Navman receives GPS signals via the internal GPS antenna. To guarantee the optimum GPS signal
strength, ensure your Navman is outdoors, or in a vehicle outdoors, and has an unobstructed view of the sky.
GPS reception is not usually affected by weather, however, very heavy rain or snow may have a negative effect
on your reception.
How do I view my GPS status?
You can view your GPS status at any time from the map screens or the Viewfinder screen. displays green
when a GPS fix is established and red when a GPS fix is unavailable. To indicate the reception strength of a GPS
fix,
displays between one and four green vertical bars.
To view your GPS status in more detail, see “GPS Status” on page 80.
To set your GPS mode, see “Setting your GPS mode” on page 81.
20
How do I go from A to B?
Your Navman is equipped with maps that provide street-level detail for door-to-door navigation, including
Points of Interest (POIs) such as accommodation, parking areas, petrol stations, railway stations and airports.
When you ... Then ...
know the address of your destination use the address-entry wizard to enter the address “How do I search for an
want to make multiple stops use the Multi-stop Trip Planner screen to enter multiple waypoints “How do I
need to find a named site, feature,
landmark or public venue
want to navigate to a NavpixTM
location
WARNING: For your safety, enter destination information before you start a journey. Do not enter a destination while
driving.
What if I miss a turn?
Back-On-Track™ Automatic Rerouting
You will be redirected if you make a wrong turn. A message informing you that your route is being re-calculated
will display at the top of the screen.
address?” on page
create a trip with multiple stops?” on page
search for a Point of Interest "How do I search for a Point of Interest (POI)?” on
30.
page
use the Go To NavPix screen to navigate to a preinstalled NavpixTM “How do I
navigate to a
22.
Navpix
TM
?” on page 58.
26.
To cancel a route re-calculation tap
. A warning will display, asking you to confirm the cancellation. If
confirmed, both the re-calculation and your current route will be cancelled.
21
How do I search for an address?
Enter a destination using the Destination Search, Keyboard and Preview screens, which used together form an
address-entry wizard.
This section provides a case study to help guide you through setting your destination.
Note: In some countries, you can search for your destination by postcode or zip code. If you are in the United Kingdom, and you
know the postcode of your destination, you can search for it from the Destination Search screen by tapping Postcode, then
entering a postcode of up to eight characters.
Quick Steps
1. Open the Destination Search screen
2. Select the country
3. Search for the city/area
4. Search for the street
5. Search for the house number
6. Tap
Case Study: How do I search for an address?
This case study will show you how to enter an address and how to navigate to it.
The address used in this example is
1 Cheyne Walk Street
Horley
Surrey
AB1 2CD,
United Kingdom.
Note: The above address is fictitious and used as an example only.
Tip: Before you enter your destination address, ensure that you have set your route preferences. For more information, see
Route Options” on page 68.
“
1. Open the Destination Search screen
.
The Destination Search screen will display.
Note: If this is the first time you are setting your destination and you have maps from more than one country installed,
then the Select a map screen will display instead of the Destination Search screen. Go directly to step 2b. The next time
you perform this procedure, the Destination Search screen will open as expected.
22
2. Select the country
Note: If you only have the maps of one country installed and selected, that country is selected for your destination by default
and cannot be changed. Go to step 3.
a) From the Destination Search screen, tap
The Select a map screen will display.
b) Select United Kingdom from the list.
The Destination Search screen will display.
3. Search for the City/Area
a) From the Destination Search screen, tap City/Area.
The Keyboard screen will display.
b) Use the Keyboard screen to search for Horley as the city or area of your destination, then tap the
search result.
The Destination Search screen will display.
4. Search for the street name and house number
a) From the Destination Search screen, tap Street Address.
The Keyboard screen will display.
.
23
Using the
The Keyboard screen will display when you are required to enter text, such as when searching for a street name. Search results
will be listed in matching order, with the closest matches appearing at the top of the list. A maximum of 99 results will
display.
The Keyboard screen can display with various layouts depending on the information you need to enter, including alphabet,
number, alternate characters and combinations of these.
You can also choose the type of keyboard you prefer from alphabetic, QWERTY and keypad. For more information, see
“Keyboard” on page 87.
Keyboard
screen
As you select each character, the first two results will display. Tap , then scroll to see more search results.
z To select a character or a search result, tap the character or search result.
z To delete a character, tap .
z To display more characters, tap 123, alt or abc, if available.
Using the
The Destination Search screen is used to select your destination by area, street, Points of Interest, intersection, city, area, state
or country.
Destination Search
screen
As you specify each part of the address, it will display at the top of the screen.
The available options will change to reflect the parts of the address still to be completed.
24
b) Use the Keyboard screen to enter Cheyne Walk as the street name of your destination, then tap the
search result.
Note: There may be multiple matches for a particular street name. Long streets that run through several neighbouring
areas, and common street names will produce search results ordered by their city or area name.
c) Use the Keyboard screen to enter 1 as the house number of your destination, then tap the search
result. The Preview screen will display.
Note: If house numbers are available, but not the one that you require, you may have to choose the same street in a
neighbouring area. Tap
section of the street the Preview screen will display.
d) Complete the following:
and select another search result. If house numbers are not available for your selected
If you want to ... Then ...
navigate to your selected destination tap .
Your route is calculated; the 3D Map screen will display.
view the position on the map screen tap the map to display the position on the 2D Map screen.
view more information about your
destination
add the destination to a multi-stop trip tap Add.
save the destination as My Home tap Save.
save the destination as a favourite tap Save.
tap More.
The Destination Detail s screen will display.
The Multi-stopTrip Planner screen will display. The address is listed as a waypoint
on the multi-stop trip. See “
26.
The New Favourite screen will display.
tap Save as My Home.
The New Favourite screen will display.
tap Save as Favourite.
How do I create a trip with multiple stops?” on page
25
How do I create a trip with multiple stops?
You can use the Multi-stop Trip Planner screen to set multiple stops or waypoints for your trip. Your route will
be calculated to go via each of these points in the specified order.
Waypoints can be added via the Multi-stop Trip Planner screen or by selecting Location, then Add to Trip from
the pop-up Map menu on the 2D Map or 3D Map screen. You can save up to 198 multi-stop trips, each with up
to 14 waypoints.
Note: Waypoints added, updated or deleted after a multi-stop trip has commenced will not affect the current route.
Quick Steps
1. Start your Multi-stop trip
2. Select the country
3. Search for the city/area
4. Search for the street and house number
5. Add additional waypoints
6. Tap
Case Study: How do I navigate to multiple addresses?
This case study will show you how to set a multi-stop trip by entering multiple waypoints.
The address used in this example is:
1 Cheyne Walk Street
Horley
Surrey
AB1 2CD,
United Kingdom.
Note: The above address is used as an example only.
Tip: Before you enter your destination address, ensure that you have set your route preferences. For more information, see
Route Options” on page 68.
“
1. Open your Multi-stop Trip screen
.
The Multi-stop Trip Planner screen will display.
26
a) Tap Add.
The Add to Trip Menu will display.
b) Tap Address.
The Destination Search screen will open.
Note: You can also add waypoints using favourites, recent destinations, POI locations and NavpixTM.
2. Select the country
Note: If you only have the maps of one country installed and selected, that country is selected for your destination by default
and cannot be changed. Go to step 3.
a) From the Destination Search screen, tap .
The Select a map screen will display.
b) Select United Kingdom from the list.
The Destination Search screen will display.
3. Search for the City/Area
a) From the Destination Search screen, tap City/Area.
The Keyboard screen will display.
b) Use the Keyboard screen to search for Horley as the city or area of your destination, then tap the
search result.
The Destination Search screen will display.
27
4. Search for the street name and house number
a) From the Destination Search screen, tap Street Address.
The Keyboard screen will display.
b) Use the Keyboard screen to enter Navman Street as the street name of your destination, then tap
the search result.
Note: There may be multiple matches for a particular street name. Long streets that run through several neighbouring
areas, and common street names will produce search results ordered by their city or area name.
c) Use the Keyboard screen to enter 1 as the house number of your destination.
The Preview screen will display.
Note: If house numbers are available, but not that you require, you may have to choose the same street in a neighbouring
area. If house numbers are not available for your selected section of the street the Destination Preview screen will display.
d) Tap Add.
The waypoint is automatically saved and the Multi-stop-Trip screen will display.
28
e) Complete the following:
If you want to ... Then ...
add another waypoint
Note: Waypoints added after a multi-stop trip has
commenced will not be included in the current route.
navigate to your selected destination tap
change the order of your waypoints tap a destination point to move.
delete all waypoints tap Clear.
delete one waypoint tap a destination point to delete.
How do I skip a waypoint during a multi-stop trip?
To skip a waypoint during a multi-stop trip, complete the following:
1. Tap the map.
The Map Menu will display.
2. Tap Route, then Skip Waypoint.
The next waypoint will be skipped and the route recalculated to the following waypoint.
tap Add.
The AddTo Trip Menu will display.
return to step 1a.
The Preview screen will display.
tap .
The 3D Map screen will display the calculated route.
The Preview screen will display.
tap Up or Down.
The Multi-stop Trip Planner screen will redisplay.
The Preview screen will display.
tap Delete.
The Multi-stop Trip Planner screen will redisplay.
29
How do I search for a Point of Interest (POI)?
A POI is a named site, feature, landmark or public venue which can be displayed as an icon on the map. POIs are
grouped by type, such as petrol stations, parking, beaches and museums.
Select a POI using the Destination Search, Keyboard and Preview screens, which used together to form a
POI-entry wizard.
Tip: You can also quickly search for certain POIs based upon your current location via the Main Menu screen.
This section provides a case study to help guide you through finding or setting your POI as a destination.
Quick Steps
1. Open the Destination Search screen
2. Select a country
3. Search for the City/Area
4. Search for a POI
5. Tap
Case Study: How do I search for a Point of Interest?
This case study will show you how to enter an address and navigate to it.
The address used in this example is:
Waterloo Railway Station
Road (A301), Waterloo
London
SE1 8UD
United Kingdom.
Note: The above address is fictitious and used as an example only.
1. Open the Destination Search screen
.
The Destination Search screen will display.
Note: If this is the first time you are setting your destination and you have maps from more than one country installed,
then the Select a map screen will display instead of the Destination Search screen. Go directly to step 2b.
The next time you perform this procedure, the Destination Search screen will open as expected.
30
Loading...
+ 70 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.