Motorola MC10H606FN Datasheet
SEMICONDUCTOR TECHNICAL DATA
2–311
REV 1
Motorola, Inc. 1996
9/96
The MC10/100H606 is a 6–bit, registered, single supply TTL to PECL
translator. The device features dif ferential PECL outputs as well as a choice
between either a differential PECL clock input or a TTL clock input. The
asynchronous master reset control is a PECL level input.
With its differential PECL outputs and TTL inputs the H606 device is
ideally suited for the transmit function of a HPPI bus type board–to–board
interface application. The on chip registers simplify the task of synchronizing
the data between the two boards.
The device is available in either ECL standard: the MECL 10H device is
compatible with MECL 10KH logic levels, with a VCC of +5 volts; while the
100H device is compatible with 100K logic levels, with a VCC of +5 volts.
• Differential 50Ω ECL Outputs
• Choice Between Differential PECL or TTL Clock Input
• Single Power Supply
• Multiple Power and Ground Pins to Minimize Noise
*
D
n
Q
n
Q
n
MR
TCLK
CLK
CLK
V
BB
1 OF 6 BITS
D
CLK
R
Q
LOGIC SYMBOL
*
1. When using PECL inputs, TCLK must be tied to ground (0V).
2. When using only one PECL input, the unused PECL input must be tied
to VBB, and TCLK must be tied to ground (0V).
3. When using TCLK, both PECL inputs must be tied to ground (0V).
MECL 10H is a trademark of Motorola, Inc.
Pinout: 28–Lead PLCC (Top View)
PIN NAMES
PIN FUNCTION
D0–D5
CLK, CLK
TCLK
MR
Q0–Q5
Q0
–Q5
V
CCE
V
CCT
GND
TTL Data Inputs
Differential PECL Clock Input
TTL Clock Input
PECL Master Reset Input
True PECL Outputs
Inverted PECL Outputs
PECL VCC (+5.0V)
TTL VCC (+5.0V)
TTL/PECL Ground
D0
567891011
25 24 23 22 21 20 19
TCLK
V
BB
CLK
CLK
MR
V
CCE
Q4
Q5
Q5
Q4
V
CCE
Q3
Q3
26
27
28
2
3
4
18
17
16
14
13
12
15
D1 D2 V
CCT
D3 D4 D5 V
CCE
Q0 Q0
GND Q1 Q1 Q2 Q2
FN SUFFIX
PLASTIC PACKAGE
CASE 776–02
Dn
L
H
X
TRUTH TABLE
MR
L
L
H
TCLK/CLK
Z
Z
X
Qn+1
L
H
L
Z = LOW to HIGH Transition
MC10H606 MC100H606
MOTOROLA MECL Data
DL122 — Rev 6
2–312
DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = + 25°C TA = + 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit Condition
I
CCTL
Supply Current 18 30 18 30 18 30 mA Outputs LOW
I
CCTH
Supply Current 13 25 13 25 13 25 mA Outputs HIGH
I
GND
Supply Current 75 90 75 90 75 95 mA
TTL DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = 25°C TA = 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
V
IH
Input HIGH Voltage 2.0 2.0 2.0 V
V
IL
Input LOW Voltage 0.8 0.8 0.8 V
V
IK
Input Clamp Voltage –1.2 –1.2 –1.2 V IIN = –18mA
I
IH
Input HIGH Current 20
100
20
100
20
100
V VIN = 2.7V
VIN = 7.0V
I
IL
Input LOW Current –0.6 –0.6 –0.6 mA VIN = 0.5V
10H PECL DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = 25°C TA = 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
I
INH
Input HIGH Current 255 145 145 µ
A
I
INL
Input LOW Current 0.5 0.5 0.5 µ
A
V
IH
Input HIGH Voltage (Note 1.) 3830 4160 3870 4190 3930 4280 mV V
CCT
= 5.0V
V
IL
Input LOW Voltage (Note 1.) 3050 3520 3050 3520 3050 3555 mV V
CCT
= 5.0V
V
OH
Output HIGH Voltage (Note 1.) 3980 4160 4020 4190 4080 4270 mV V
CCT
= 5.0V
V
OL
Output LOW Voltage (Note 1.) 3050 3370 3050 3370 3050 3400 mV V
CCT
= 5.0V
V
BB
Output Bias Voltage (Note 1.) 3600 3710 3630 3730 3670 3790 mV V
CCT
= 5.0V
1. PECL VIL, VIH, VOL, VOH VBB are given for V
CCT
= V
CCE
= 5.0V and will vary 1:1 with the power supply.
100H PECL DC CHARACTERISTICS (V
CCT
= V
CCE
= 5.0V ±5%)
TA = 0°C TA = 25°C TA = 85°C
Symbol Characteristic Min Max Min Max Min Max Unit Condition
I
INH
Input HIGH Current 255 145 145 µ
A
I
INL
Input LOW Current 0.5 0.5 0.5 µ
A
V
IH
Input HIGH Voltage (Note 1.) 3835 4120 3835 4120 3835 4120 mV V
CCT
= 5.0V
V
IL
Input LOW Voltage (Note 1.) 3190 3525 3190 3525 3190 3525 mV V
CCT
= 5.0V
V
OH
Output HIGH Voltage (Note 1.) 3975 4120 3975 4120 3975 4120 mV V
CCT
= 5.0V
V
OL
Output LOW Voltage (Note 1.) 3190 3380 3190 3380 3190 3380 mV V
CCT
= 5.0V
V
BB
Output Bias Voltage (Note 1.) 3600 3720 3600 3720 3600 3720 mV V
CCT
= 5.0V
1. PECL VIL, VIH, VOL, VOH VBB are given for V
CCT
= V
CCE
= 5.0V and will vary 1:1 with the power supply.
Loading...