Mitel 3300 User Manual 2

Page 1
Mitel PBX interface with Conferencing Server
Configuration Notes
Note: This document section is maintained by Mitel Networks
When referring to any information in this document please also check the Additions & Correction section on the last page for up dates.
7/4/2004 Page 1 of 22
Page 2
Mitel PBX interface with Conferencing Server Configuration Notes
Mitel PBX interface with Conferencing Server Configuration Notes........................1
Introduction....................................................................................................................3
3300ICP with ISDN or SX2000 with ISDN...............................................................3
Example of T1 PRI programming on 3300 or SX2000...........................................3
Class Of Service – changes from default values................................ ................3
Link Descriptor Assignment....................................................................................4
Digital Link Assignment...........................................................................................4
MSDN- DPNSS-DASSII Trunk Circuit Descriptor................................................5
Trunk Service Assignment......................................................................................5
Digital Trunk Assignment................................ ........................................................5
3300 ICP with T1/D4 or SX2000 with T1/D4 ...........................................................5
Example of T1/D4 (CAS) Programming on 3300 or SX2000................................6
Class Of Service – changes from default values................................ ................6
Link Descriptor Assignment....................................................................................7
Digital Link Assignment...........................................................................................7
Digital E and M Trunk Circuit Descriptor Assignment................................ ........8
Trunk Service Assignment......................................................................................8
Digital Trunk Assignment................................ ........................................................9
Example of ARS Programming on 3300 ICP/SX2000...........................................9
Create Trunk Group .................................................................................................9
Add individual trunks to trunk group......................................................................9
Create Digit Modification Assignment.................................................................11
Create Route Assignment.....................................................................................11
Create ARS Digits Dialed Assignment................................................................11
SX200 with ISDN........................................................................................................12
SX200 with T1/D4................................ ......................................................................20
T1 Crossover cable wiring Specifications [RJ45 Connector]..............................21
7/4/2004 Page 2 of 22
Page 3
Introduction
This document describes the configuration of Mitel Networks PBX’s to correctly interface to the Interactive Group Communication System by VCon. For more information on the configuration of the IGC, please refer to Mitel 3300 - RemoteAbility IGC Integration Specifications V1. Note that all PBX configuration should be undertaken by a qualified Technician.
3300ICP with ISDN or SX2000 with ISDN
Attach VCon IGC server T1 link to NSU, DSU or Embedded PRI card
o Configure hardware for Line Termination through jumpers or DIP
switch – please refer to the Technician’s Handbook of the correct product (3300 or SX2000)
connect to server with a straight through cable
Program trunks
o for example, please see Example of T1 PRI programming on 3300
Program PRI link characteristics though IMAT (for NSU or DSU) or through ESM ( embedded PRI card in 3300ICP)
o Protocol used is DMS-250, user side
Reset NSU or PRI card to allow new configuration to load
Test link to server by dialing <feature access code for individual trunk
access> <trunk number><any 4 digit number>< # > e.g. <**2><6101><1000><#>
o You should hear “Welcome to Remoteability”
Program ARS so that a single four digit number accesses the IGC system
o Program trunk group o Add trunks to trunk group o Create Digit Modification Assignment o Create Route Assignment o Create ARS Digits Dialed Assignment o Please see Example of ARS Programming on 3300 or SX2000
Example of T1 PRI programming on 3300 or SX2000
Class Of Service – changes from default values
Public Network Access via DPNSS Yes
7/4/2004 Page 3 of 22
Page 4
ANI/DNIS/ISDN Number Delivery Yes
ISDN NODE
Service Limit (millisec.):
Controller
Shelf
Link Descriptor Assignment
Number: 4 Address for Message Control: A
BER - Maintenance Limit, 10**-n: 4 BER - Service Limit, 10**-n: 3 Data Call Alternate Digit Inversion: Yes Framing Losses in 24 hrs - Maintenance Limit: 255 Framing Losses in 24 hrs - Service Limit: 9000 Integrated Digital Access: Satellite Link Delay: No Slip Rate - Maintenance Limit (slips/24hr.): 5000 Slip Rate - Service Limit (slips/24hr.): 7000 Alarm Debounce Timer ­Voice Encoding: Invert Data Encoding: Nil QSIG Private Network Access: No Digital Link Fault Delay Timer (sec.): 240 Termination Mode: LT T1 Only: B8ZS Zero Code Suppression: Yes Operation Mode: DSX-1 CSU Tx Line Build-Out (dB.): DSX-1 Line Length (Ft.): 0-133 Extended Super Frame: Yes Inverted D channel ( DPNSS only ): No E1 Only: CRC-4 Enabled: Yes E1 Line Length (Ft.): 0-133 E1 Impedance (Ohms): 120
500
Digital Link Assignment
Module 1 1 6 1 1 1 UNIVERSAL T1
1 1 6 1 1 2 UNIVERSAL T1
Port Unit
7/4/2004 Page 4 of 22
Slot Link Interface Type
Page 5
MSDN-DPNSS-DASSII Trunk Circuit Descriptor
Local Office
Absorb:
Dual
Number Card Type 4 UNIVERSAL T1 Incoming
Seizure Priority
Far End Connection
MSDN- DPNSS
Trunk Service Assignment
Trunk Service Number: 4 Release Link Trunk: No
Class of Service: 4 Class of Restriction: 1
Baud Rate: 300 Intercept Number: 1
Non-dial In Trunks Answer Point - Day: Non-dial In Trunks Answer Point - Night 1: Non-dial In Trunks Answer Point - Night 2: Dial In Trunks Incoming Digit Modification ­Dial In Trunks Incoming Digit Modification - Insert:
Trunk Label: ISDN Trunk
0
Signalling Protocol
Digital Trunk Assignment
Cabinet: 6 Shelf: 1 Slot: 1 Circuit: 1 Card Type: UNIVERSAL T1 Trunk Number: 6101 Trunk Service Number: 4 DTS Service Number: Circuit Descriptor Number: 4 Interconnect Number: 1
3300 ICP with T1/D4 or SX2000 with T1/D4
7/4/2004 Page 5 of 22
Page 6
Attach VCon IGC server T1 link to NSU, DSU or Embedded PRI card
o Configure hardware for Line Termination through jumpers or DIP
switch – please refer to the Technician’s Handbook of the correct product (3300 or SX2000)
connect to server with a straight through cable
Program trunks
o for example, please see Example of T1/D4 Programming on 3300
or SX2000
Test link to server by dialing <feature access code for individual trunk access> <trunk number><any 4 digit number>< # > e.g. <**2><6101><1000><#>
o You should hear “Welcome to Remoteability”
Program ARS so a single four digit number accesses the IGC system
o Program trunk group o Add trunks to trunk group o Create Digit Modification Assignment ** see following note
o Create Route Assignment o Create ARS Digits Dialed Assignment
o Please see Example of ARS Programming on 3300 or SX2000
**Note: The Dialogic card in the IGC server is expecting ANI on the T1D4 trunk, but the 3300 or SX2000 does not deliver ANI over T1D4. This will result in a 10 to 15 second delay in accessing the IGC after the trunk access number is dialed. To correct this, send an ANI digit string to the trunk through the Digit M odification Form. See below.
Digit Modification Assignment
Digit Modification Number
Number of Digits to Absorb
Digits to be Inserted
Final Tone Plan/Information Marker
1 3 2 0 3 1 <T01> 4 0 **6135922122**
Example of T1/D4 (CAS) Programming on 3300 or SX2000
Class Of Service – changes from default values
Public Network Access via DPNSS Yes
7/4/2004 Page 6 of 22
Page 7
ANI/DNIS/ISDN Number Delivery Yes
Service Limit (millisec.):
Controller
Shelf
Descriptor
Link Descriptor Assignment
Number: 4 Address for Message Control: BER - Maintenance Limit, 10**-n: 4 BER - Service Limit, 10**-n: 3 Data Call Alternate Digit Inversion: Yes
Framing Losses in 24 hrs - Maintenance Limit: 255 Framing Losses in 24 hrs - Service Limit: 9000 Integrated Digital Access: T1D4 Satellite Link Delay: No Slip Rate - Maintenance Limit (slips/24hr.): 5000
Slip Rate - Service Limit (slips/24hr.): 7000 Alarm Debounce Timer -
Voice Encoding: Invert Data Encoding: Nil QSIG Private Network Access: No
Digital Link Fault Delay Timer (sec.): 240 Termination Mode: NT T1 Only: B8ZS Zero Code Suppression: Yes Operation Mode: DSX-1 CSU Tx Line Build-Out (dB.): DSX-1 Line Length (Ft.): 0-133 Extended Super Frame: No Inverted D channel ( DPNSS only ): No E1 Only: CRC-4 En abled: No E1 Line Length (Ft.): 0-133 E1 Impedance (Ohms): 120
500
Digital Link Assignment
Module 1 1 6 1 1 1 UNIVERSAL T1 4 Remoteability
1 1 6 1 1 2 UNIVERSAL T1 4 T1D4
Digital
Port Unit
Slot
Link Interface Type
Link
7/4/2004 Page 7 of 22
Comment
Page 8
Digital E and M Trunk Circuit Descriptor Assignment
Combination
Drop Digit Rcvr for Outgoing Audio Before Ans Sup:
Absorb:
Number: 4 Call Collision Handling: AT&T
AT&T Call Collision Handling: Backoff Ignore Far End Disconnect: No Release Acknowledge Timer: 80 Address Signalling: DTMF Disconnect Timer: 300 Incoming Start Type: Wink Dial Tone on Incoming Seize: No Outpulse Delay Timer: 800 Outgoing Start Type: Wink Supervision Timer: 200 Maximum Wink Timer: 400 Minimum Wink Timer: 100 Guard Timer: 500 Fake Answer Supervision After Outpulsing: No Ignore Answer Supervision: No Release Supervision Expected: Yes Audio Inhibit Until Answer Supervision: Yes Far End Connection: Main PBX Facility Type: Minimum Flash Timer: 250 Maximum Flash Timer: 200
No
Flash Timer: 300
Trunk Service Assignment
Trunk Service Number: 4 Release Link Trunk: No
Class of Service: 4 Class of Restriction: 1 Baud Rate: 300 Intercept Number: 1 Non-dial In Trunks Answer Point - Day:
Non-dial In Trunks Answer Point - Night 1: Non-dial In Trunks Answer Point - Night 2:
Dial In Trunks Incoming Digit Modification ­Dial In Trunks Incoming Digit Modification - Insert: Trunk Label: T1 Trunk
7/4/2004 Page 8 of 22
0
Page 9
Digital Trunk Assignment
Cabinet: 6 Shelf: 1 Slot: 1 Circuit: 1 Card Type: UNIVERSAL T1 Trunk Number: 6101 Trunk Service Number: 4 DTS Service Number: Circuit Descriptor Number: 4 Interconnect Number: 1
Example of ARS Programming on 3300 ICP/SX2000
Create Trunk Group
Trunk Group Assignment
Trunk Group Number
Hunt Mode
Trunk Group Busy RAD
Maximum Network Hop
Comments
3 Terminal Analog TG 4 Circular Remoteabilty 5 Terminal To Sx2000
Add individual trunks to trunk group
- all 23 ISDN trunks or 24 T1/D4 trunks should be added to the trunk group
Trunk Group Members
Member Trunk Number 1 6101
7/4/2004 Page 9 of 22
Page 10
2 6102 3 6103 4 6104 5 6105 6 6106 7 6107 8 6108 9 6109 10 6110
7/4/2004 Page 10 of 22
Page 11
Create Digit Modification Assignment
Digits to be
Number
Modification
Route
Compression
Number of Digits to
- in this example, we are using Digit Modification number 4, and there are no digits to absorb or to insert
Digit Modification Assignment
Digit Modification Number
1 3 2 0 3 1 <T01> 4 0
Number of Digits to Absorb
Inserted
Final Tone Plan/Information Marker
5 0
Create Route Assignment
- in this example, we are using Route 4
Route Assignment
XNET Trunk Group Number
Type
Route Number
Trunk Group
COR Group Number
Digit Number
Digits Before Outpulsing
1 1 1 1 Off 2 1 1 Off 3 3 1 3 Off 4 4 1 4 Off 5 5 1 1 Off
Create ARS Digits Dialed Assignment
- in this example, the digits dialed to access the Vcon IGC are 1100
ARS Digits Dialed Assignment
Digits Dialed
Follow
1100 0 Route 4
Termination Type
Termination Number
201 4 Route 1
7/4/2004 Page 11 of 22
Page 12
SX200 with ISDN
Attach VCon IGC server to PRI card with straight through cable
o Configure hardware for Line Termination. Please refer to SX200
Technician’s Handbook for more information.
Program trunks
o Please see Example of T1 PRI Programming on SX200
Use IMAT to configure PRI card for DMS250, user side
Reset PRI card to allow new configuration to load
Program ARS
o See SX200 Technician’s Handbook for more information
7/4/2004 Page 12 of 22
Page 13
Example of T1 PRI Programming on SX200
Refer to SX200 EL/ML Technicians Handbook , Programming a PRI, for System Configuration, Class of Service Options and System Options/System Timers.
Form 13 Assign T1 E&M circuit descriptor to the ISDN trunk.
7/4/2004 Page 13 of 22
Page 14
7/4/2004 Page 14 of 22
Page 15
7/4/2004 Page 15 of 22
Page 16
Define the incoming ISDN trunk as a Dial In trunk in form 15
7/4/2004 Page 16 of 22
Page 17
Assign the ISDN trunks to a trunk group in Form 16
7/4/2004 Page 17 of 22
Page 18
Select a T1 Link Descriptor for the ISDN trunks in form 42
7/4/2004 Page 18 of 22
Page 19
7/4/2004 Page 19 of 22
Page 20
Assign the ISDN link descriptor to slot 6 and/or slot 8 on the PRI card bay, Form 43
Form 44, Network Sync - To be determined by qualified Technician
SX200 with T1/D4
Attach VCon IGC server to SX200 with cross over cable.
Program trunks for T1/D4 . All values are default.
Program ARS so that a single four digit number accesses the IGC system
o See SX200 Technician’s Handbook for more information o Send simulated ANI down trunk using Digit Modification Table, form
22 as shown below with digit mod number 3. The Dialogic card in the IGC expects ANI, and there will be a 10 – 15s delay accessing the server unless such a string is sent down the trunk.
7/4/2004 Page 20 of 22
Page 21
T1 Crossover cable wiring Specifications [RJ45 Connector]
Supplied with RemoteAbility system.
Connector
A Pin 1 4 2 5 4 1 5 2
Connector
B Pin
7/4/2004 Page 21 of 22
Page 22
Addition & Corrections
The change I had to make was with the ANI/DNIS insertion in digit mod with T1/D4 trunks: The doc says above to insert **6135922122** The correct format for this string is :
*ANI*DNIS* We used this at for fixed ANI at Pyramid: *3125551212*7900* For caller's ANI: *<E>*7900*
7/4/2004 Page 22 of 22
Loading...