Miele Platinum Plus Operating instructions

Operating instructions for Washing machine Platinum Plus

To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time.

en-GB

M.-Nr. 07 616 320

Caring for our environment

Disposal of the packing material

The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled.

Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation!

Rather than just throwing these materials away, please ensure they are offered for recycling.

Disposal of your old machine

Electrical and electronic machines often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your machine. Please do not therefore dispose of it with your household waste.

Please dispose of it at your local community waste collection / recycling centre or contact your Dealer for advice. Ensure that it presents no danger to children while being stored for disposal.

It should be unplugged or disconnected from the mains electricity supply by a competent person.

Contents

Caring for our environment .........................................2

Warning and Safety instructions .....................................6

Description of the machine.........................................10

Control panel .....................................................10

Before using for the first time.......................................12

Washing environmentally and economically ..........................13

Energy and water consumption ....................................13

Detergent .....................................................13

Choosing the correct additional option (Short, Soak, Pre-wash)............13

When drying with a tumble dryer ...................................13

How to wash correctly.............................................14

Additional options ................................................19

Short............................................................19

Pre-wash ........................................................19

Soak ............................................................19

Water plus .......................................................19

Spinning ........................................................20

Final spin speed ..................................................20

Rinse and interim spin ...........................................20

To omit the final spin (Rinse hold) ..................................20

To omit rinse and interim spin and the final spin .......................20

Programme chart .................................................21

Programme sequence .............................................23

Garment care label symbols ........................................25

Contents

Changing the programme sequence .................................26

Cancelling a programme ............................................26

Interrupting a programme ...........................................26

Changing a programme ............................................26

Skipping a programme stage ........................................26

Adding or removing laundry after a programme has started ................27

Detergent .......................................................28

The correct detergent ..............................................28

Water softeners ...................................................29

Washing with several components ....................................29

Fabric conditioners and liquid starch ..................................30

Automatic dispensing of fabric conditioner or liquid starch to laundry

at the end of a programme ........................................30

Adding fabric conditioner or starch separately ........................30

Colour run and dye removers / dyes ...................................30

Cleaning and care ................................................31

External casing and fascia panel .....................................31

Extra cleaning ..................................................31

Cleaning the detergent dispenser drawer...............................31

Cleaning the water inlet filters ........................................33

Problem solving guide ............................................34

The programme does not start .......................................34

The wash programme stops and a fault indicator light comes on ............35

A fault indicator light comes on but the wash programme continues as normal. . 36

General problems .................................................37

An unsatisfactory wash result ........................................38

The drum door does not open when you press the Door button..............39

Opening the drum door in the event of a blocked drain outlet

and/or power failure................................................40

Blocked drain outlet .............................................40

Contents

After sales service ................................................42

Future updates (PC) .............................................42

Appliance guarantee ............................................42

Optional spare parts and accessories ...............................42

Installation and connection ........................................43

Front view........................................................43

Rear view ........................................................44

Installation surface.................................................45

Installing the washing machine ....................................45

Removing the transit bars ...........................................45

Re-fitting the transit bars ............................................47

Levelling the machine ..............................................48

Screwing out and adjusting the feet .................................48

Building under a continuous worktop/in a kitchen run ...................49

Washer and Dryer stack ..........................................49

The Miele water protection system ....................................50

Connection to the water supply .......................................51

Connection to the drainage system....................................52

Electrical connection U.K. ...........................................53

Consumption data ................................................54

Technical data ...................................................55

Programmable functions...........................................57

Water plus system .................................................57

Gentle action .....................................................58

Top-up rinse for Cottons ............................................59

Memory function ..................................................60

Soak ............................................................61

Optional accessories..............................................62

CareCollection ....................................................62

Warning and Safety instructions

This washing machine is not This washing machine conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.

To avoid the risk of accidents and damage to the washing machine, please read these instructions carefully before using it for the first time. They contain important information on its installation, safety, use and maintenance.

Keep these instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner.

Correct application

This washing machine is for

domestic use only and can only be used to wash items which are specified by the manufacturer to be machine-washable on the wash care label, and textiles composed of hand-washable wool or wool blend fabrics as well as satin, lace, silk and other hand-washable garments. Any other applications may be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.

intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety.

Safety with children

Keep children away from the

washing machine at all times. It is not a toy! To avoid the risk of injury do not allow children to play on or near it or to play with its controls. Supervise children whilst you are using it.

Older children may only use the

washing machine if its operation has been clearly explained to them and they are able to use it safely, recognising the dangers of misuse.

For machines with a 'porthole' door,

remember that the porthole glass will be hot when washing at very high temperatures. Do not let children touch it.

Warning and Safety instructions

Technical safety

Before setting up the washing

machine, check it for any externally visible damage. Do not install or use a damaged washing machine.

Before connecting the washing

machine, ensure that the connection data on the data plate (voltage and connected load) match the mains electricity supply. If in any doubt, consult a qualified electrician.

The electrical safety of this washing

machine can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested, and where there is any doubt the household wiring system should be inspected by a qualified electrician. The manufacturer cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).

Do not connect the washing

machine to the mains electricity supply by an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating).

Faulty components must only be

replaced by genuine Miele original spare parts. Only when these parts are fitted can the safety standards of the machine be guaranteed.

Unauthorised repairs could result in

unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. Ensure current is not supplied to the machine until after maintenance or repair work has been carried out.

If the connection cable is faulty it

must only be replaced by a Miele approved service technician to protect the user from danger.

In the event of a fault or for cleaning

purposes, the washing machine is only completely isolated from the electricity supply when:

– it is switched off at the wall socket

and the plug is withdrawn, or

– it is switched off at the mains, or

– the mains fuse is withdrawn, or the

screw-out fuse is removed (in countries where this is applicable).

This washing machine must only be

connected to the on-site water supply using a new hose kit. Old hoses must not be re-used.

In countries where there are areas

which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the machine and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.

Warning and Safety instructions

This washing machine may only be

used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer.

Do not make any alterations to the

washing machine, unless authorised to do so by Miele.

Correct use

Do not install your washing machine

in rooms where temperatures below freezing may occur. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

Before using the washing machine

for the first time, check that the transit bars at the rear of the machine have been removed (see section on "Installation and connection"). During spinning, a transit bar which is still in place may result in damage to both the machine and adjacent furniture or appliances.

Turn off the stopcock if the machine

is to be left for any length of time (e.g. holiday), especially if there is no floor drain (gully) in the immediate vicinity.

Flooding danger.

If hooking the drain hose into a wash basin, check that the water can drain off quickly enough to prevent the sink from overflowing. Make sure the drain hose is secure, so that the force of the water flowing out of the hose does not dislodge it.

Take care to ensure that foreign

objects (e.g. nails, pins, coins, paper clips) do not find their way into the machine with the laundry. These may damage components of the machine (e.g. suds container, drum), which in turn can result in damage to the laundry.

If the correct amount of detergent is

dispensed, the machine should not need to be descaled. If, however, you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging. A special descaling agent is available to order from Miele or via the internet on www.miele-shop.com.

Warning and Safety instructions

Textiles which have been

pre-treated in solvent based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine.

Never use solvent based cleaning

agents, e.g. those containing benzene, in this machine, as this may result in damage to component parts and create toxic fumes. Such agents also pose a fire and explosion hazard.

Never use solvent based cleaning

agents, e.g. those containing benzene, to clean the outside surfaces of this machine. They can cause damage to plastic surfaces.

Only use dyes specified by the

manufacturer as being suitable for use in a domestic washing machine. Always observe the manufacturer's instructions carefully.

Colour run and dye removers

contain sulphur compounds which can cause damage such as corrosion. Do not use these products in this machine.

Only remove laundry from the

washing machine once the drum has stopped turning. Reaching into a moving drum is extremely dangerous and could result in injury.

Accessories

Accessory parts may only be fitted

when expressly approved by Miele. If other parts are used, guarantee, performance and product liability claims will be invalidated.

Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

If liquid detergent comes into

contact with the eyes, rinse them thoroughly with lukewarm water imme diately. If swallowed, seek medical assistance immediately and retain the packaging or label for reference. Those with skin problems or sensitive skin should avoid their skin coming into contact with liquid detergent.

Description of the machine

Control panel

a Display

See the following page for more information.

b Start button

Starts the wash programme.

c Additional option buttons

Additional options can be added to the basic programme. Use the top button to select either the Short, Pre-wash,orSoak option. Use the lower button to select the Water plus option. Indicator light on = option selected Indicator light off = option not

selected

d Indicator lights for spin speed,

Rinse hold or Without spin.

e Spin button

For selecting the final spin speed, Rinse hold or Without spin.

f Programme selector

For selecting the wash programme and temperature for that programme. The programme selector can be turned clockwise or anti-clockwise.

g Programme sequence indicator

lights

Show which section of the wash programme has been reached.

h Check lights

i I-On/0-Off button

For switching the machine on or off or interrupting a programme.

j Door button

Opens the machine door.

Description of the machine

Display

The display shows:

the programme duration (Time left

–

display)

the programmable functions

–

Programme duration

After the start of a programme, the estimated programme duration will appear in the display in hours and minutes.

During the first 10 minutes the washing machine measures how much water is being absorbed by the laundry and uses this to calculate the load. The programme duration may be longer or shorter depending on this absorbency rate.

Programmable functions

The programmable functions can be used to tailor washing programmes to suit your individual requirements. In programming mode, the display will show the function selected.

Before using for the first time

Before using the machine for the first time ensure that it is correctly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened. Otherwise there is a risk of water leakage during use.

This washing machine has undergone a thorough functional test in the factory and there will be some residual water in the drum from this process.

For safety reasons spinning is not possible until the machine has been prepared for using for the first time. To activate the spinning function you must run a wash programme without laundry and without detergent.

Using detergent could result in an excessive build-up of foam.

This also activates the ball valve. The ball valve prevents detergent escaping from the suds container into the sump during a wash programme, thus making maximum use of the detergent.

Open the stopcock.

Press the I-On/0-Off button in.

Turn the programme selector to Cottons 60°C.

Press Start.

When this programme has finished turn the programme selector to Finish. Your washing machine is ready for using for the first time.

Washing environmentally and economically

Energy and water consumption

Water consumption and energy

–

usage are determined by the size of the load. To make the most out of your machine, load the maximum dry load for the programme you are using.

Use the Automatic and Express

–

programmes for small loads.

When smaller amounts of laundry are

–

washed using the Cottons programmes, the automatic load recognition system will reduce the amount of water, time and energy used. This may mean that the time left shown in the display is adjusted during the course of the wash programme.

– Using the Cottons 60°C programme

instead of the Cottons 95°C programme will give energy savings of between 35% and 45%. This is sufficient for most levels of soiling. For stubborn or old stains, use the Soak option.

–

Use the additional option Soak instead of Pre-wash. If Soak is followed immediately by a main wash, the same suds are used.

Detergent

Do not exceed the amounts of

–

detergent recommended by the manufacturer on the packaging.

Reduce the amount of detergent with

–

smaller loads (approx.

/3less than the amount recommended can be used when washing a half load).

Choosing the correct additional option (Short, Soak, Pre-wash)

Select:

A wash programme together with the

–

Short option for light to normal soiling where there are no obvious marks.

– A wash programme without any

additional options for normal to heavy soiling with visible staining.

– A wash programme together with the

Soak option for heavily soiled laundry.

– The Pre-wash additional option for

laundry with large amounts of dirt (e.g. dust, sand).

When drying with a tumble dryer

Selecting the highest possible spin speed for the wash programme will save energy when drying in a tumble dryer afterwards.

How to wash correctly

Brief instructions

The headings numbered A, B, C,... show the operating sequence and can be used as brief instructions.

A Sort the laundry

^ Empty all pockets.

Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine.

Badly soiled areas, stains etc. should be cleaned as soon as possible, preferably whilst still fresh. Spillages should be carefully dabbed off using a soft colourfast cloth. Do not rub!

Badly soiled areas can be pre-treated with liquid detergent, stain removers etc. first, following the manufacturer's instructions. With particularly stubborn stains ask your dry cleaner for advice.

If you use a solvent-based clean

ing agent (e.g. one containing ben zene) to pre-treat a stain, make sure that any plastic parts (e.g. buttons) are protected, and that the cleaning agent is rinsed off before washing the garment in the machine.

Do not use solvent-based

cleaning agents in this machine.

Sort the laundry by colour and by

care label. Most garments have a textile care label in the collar or side seam.

Dark textiles often contain excess dye and should be washed separately several times before being included in a mixed load. Always wash whites and coloureds separately.

– Curtains: Remove lead weights first

or place in a laundry bag.

–

Underwiring and collar stiffeners: Any loose wiring in bras, shirt collar stiffeners, etc. should be removed or sewn in.

–

Knitted garments, trousers and jeans, T-shirts and sweat shirts: Turn inside out, if recommended by the manufacturer.

–

Close any zips, fasten hooks and eyes etc before washing.

–

Fasten duvet covers etc. to prevent small items from being rolled up inside them.

Do not wash any items in this machine which are specified by the manufacturer as not washable on the care label. (h symbol)

How to wash correctly

B Switch on the washing machine

C Load the drum

Press the Door button to open the

drum door.

Unfold the laundry and load loosely

in the drum. Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning.

The most efficient use of energy and water is achieved when a full load is washed. Do not overload as this causes creases and reduces cleaning efficiency.

Make sure that no garments are caught between the drum door and seal.

D Select a programme

^ Turn the programme selector to the

required programme.

The estimated programme duration will then show in the display.

Shut the door with a gentle swing.

How to wash correctly

E Select additional option(s)

Each press of the top button selects the additional options in the following order: Short, Pre-wash, Soak, no selection.

Use the lower button to select the Water plus option.

^ Select the option you want.

Not all the additional options are suitable for every programme.

F Select a spin speed

Press the "Spin" button repeatedly

until the indicator light for the spin speed you want comes on.

You can only select additional options which are compatible with the programme being used.

G Add detergent

It is important to dispense the correct amount, because...

. . . too little detergent results in:

Laundry not getting properly clean

–

and with time it may become grey and hard to the touch.

Greasy particles clinging to the

–

laundry.

Limescale deposits on the heater

–

elements.

. . . too much results in:

– Excessive foam which causes a low

level of agitation and poor wash, rinse and spin results.

– Higher water consumption (an

additional rinse cycle will automatically switch in).

– A burden to the environment.

How to wash correctly

Pull out the detergent drawer and

place detergent in the compartments as follows:

Detergent for the pre-wash (divide the total recommended amount as follows: add

and

/3to compartment j).

Detergent for the main wash, including Soak if selected

/3to compartment i

Fabric conditioners or liquid starch

Close the detergent drawer.

See "Detergent" for further information.

How to wash correctly

H Start the programme

Press the flashing Start button.

The estimated programme duration will show in the display. During the first 10 minutes the washing machine measures how much water is being absorbed by the laundry. The programme duration may be longer or shorter depending on this absorbency rate.

I Remove the laundry

Only remove laundry from the machine once the drum has stopped turning. Reaching into a moving drum is extremely dangerous and could result in injury.

When the programme has finished, the Anti-crease/Finish indicator light will come on.

^ Press the Door button to open the

drum door.

Remove the laundry.

Check the folds in the door seal for

any small articles, e.g. buttons which might be lodged there.

^ Press and release the I-On/0-Off

button and turn the programme selector to Finish.

^ Close the drum door. Otherwise there

is the danger of objects being placed inadvertently in the drum. If these remained unnoticed and were washed in the next load, they could damage the laundry.

Check that all items have been removed from the drum. Items left in the drum could discolour other items in the next wash or become discoloured themselves.

Additional options

You can use the additional option buttons to augment the basic wash programmes.

Short

For light to nomal soiling with no visible staining.

The duration of the main wash is reduced.

In the Dark garments and Denim programmes, 2 rinses will be carried out instead of 3.

Pre-wash

For laundry with large amounts of dirt e.g. dust, sand.

Soak

For heavily soiled and stained items with protein stains (e.g. blood, fats and oils, cocoa).

Water plus

If you want to increase the water level for a wash process you can choose one of four settings for the Water plus button. See "Programmable functions Water plus system".

The machine is set at the factory so that the water level in the main wash and rinses will be increased if the Water plus button is pressed.

–

A length of time of between 30 minutes and 2 hours can be programmed in 30 minute increments for the soak process.

–

The default setting is 2 hours.

To programme in a different soak period see "Programmable functions – Soak".

Spinning

Final spin speed

Programme rpm

Cottons 1300

Minimum iron 1200

Delicates 600

Automatic 900

Dark garments 1200

Shirts 600

Denim 900

Express 1300

Silks 400

Woollens 1200

Drain/Spin 1300

Separate rinse/Starch 1200

You can reduce the final spin speed. However, you cannot select a final spin speed higher than that shown in the chart above.

Rinse and interim spin

There is a spin after the main wash and between the rinses. A reduction in the final spin speed will also reduce the interim spin speed. If a spin speed of less than 700 rpm is selected for a Cottons programme, an additional rinse is introduced.

To omit the final spin (Rinse hold)

Select the Rinse hold setting. The

laundry will not be spun and will remain suspended in the final rinse water. This reduces creasing if the laundry is not going to be removed from the drum immediately after the end of the programme.

To start the final spin

–

The Rinse hold indicator light above the "Spin" button will be lit up. Use the "Spin" button to select the spin speed you want. The final spin will then begin.

– To end the programme

Press the Door button. The water will drain away. Press the Door button again to open the door.

To omit rinse and interim spin and the final spin

^ Select the Without spin setting. The

laundry is not spun after the final rinse. The water will drain away and the machine will go straight into the anti-crease stage. An additional rinse is introduced if this setting is selected with the Cottons, Minimum Iron and Automatic programmes.

+ 44 hidden pages