INSTRUCTION MANUAL
MclNTOSH MODEL MC-60
60 WATT POWER AMPLIFIER
Type A-121
Serial No. 5F846 and above
MclNTOSH LABORATORY, INC.
2 Chambers St. Binghamton, N. Y.
U.S.A.
ELECTRICAL AND MECHANICAL SPECIFICATIONS
Specifications for the Mclntosh Model MC-60 Audio Amplifier
Power Supply
Power Consumption
Power Output
Input Level
Frequency Range
Harmonic Distortion
Intermodulation Distortion
Impulse Distortion
Noise and Hum Level
Damping Factor
Input Impedance
117/125 volts, 50/60 cycles
280 watts at 60 watts output
155 watts at zero signal output
60 watts continuous
Input #1, 0. 5 volts to 30 volts, with gain control
Input #2, 2. 5 volts (for use with Mclntosh Audio
Compensators and Pre-Amps)
20 to 30, 000 cycles ± .1 db at 60 watts output
16 to 60, 000 cycles ± .5 db at 60 watts output
1.0 to 100, 000 cycles ± 1.0 db at 30 watts output
Less than 0.5% at 60 watts output or less, 20
to 20, 000 cycles.
Less than 0.5% instantaneous peak power is below 120 watts
Negligible
90 db or more below rated output
12 or better for 4, 8, and 16 ohm output, 16
for 600 ohms
0. 5 meg for 0. 5 volt input and 0. 13 meg for
2. 5 volt input, 20 cycles to 40 KC
Output Impedance
Phase Shift
Tube Complement
Auxiliary Equipment Connection
Size
Weight
Finish
4, 8, 16, 83 (70.7 volts) and 600 ohms (600 ohm
is balanced to ground)
±8° 20-20.000 cycles
Rectifier:
Pre-Amp:
Phase Inverter:
Voltage Amp:
Driver:
Output:
2-5U4GB
12AX7
12AU7
12BH7
12AX7
2 KT-88/6550
Designed to power C-4, C-8 and other Mclntosh
pre-amplifiers
14" x 10" x 8" high, chassis type construction
46 pounds net
Chrome and Black
DESCRIPTION
The Mclntosh Model MC-60 is a 60 watt high fidelity power amplifier designed for home
entertainment systems and professional applications where high power and distortion free
performance is required. The Model MC-60, like all other Mclntosh power amplifiers, uses
the exclusive Mclntosh high efficiecny output circuit and bifilar output transformer to obtain
the high standard of performance found in this amplifier. Some of the more important characteristics of the amplifier are; less than 0. 5% harmonic distortion at any power output up to
60 watts and at any frequency in the audio spectrum, 20 to 20, 000 cps; less than 0. 5% intermodulation distortion for all power levels up to 120 instantaneous peak watts; and noise and
hum level 90 db or more below the rated output level.
The MC-60 has two high impedance inputs and may be operated from any signal source
delivering 0. 5 volts or more, or directly from a Mclntosh Audio Compensator or Pre-Amplifier. Output impedance of 4, 8 and 16 ohms are provided for direct connection to loud-
speakers. Additional outputs for 83 ohms (70.7 volts) and 600 ohms are provided for use
with multiple speaker systems, lines, etc.
INSTALLATION
Location
The MC-60 should be located in a well-ventilated area. If the amplifier is housed in a
cabinet or other enclosure, holes must be provided for air circulation.
Input Connections
1. When a Mclntosh Audio Compensator or Pre-Amplifier of the non-self powered type
is used with the MC-60, plug the pre-amplifier's output-power cord into the "PRE-AMP
INPUT" receptacle on the MC-60 and turn the "GAIN" control fully counter clockwise. This
receptacle supplies the required plate and filament power to the pre-amplifier equipment as
well as providing the necessary audio connections.
For pre-amplifier installation, adjustment and operation refer to the pre-amplifier's
instruction manual.
2. When using a self-powered Mclntosh Audio Compensator or Pre-Amplifier, connect
the audio output from the pre-amplifier to the input of the MC-60 using the cable supplied
with the pre-amplifier. Turn the "GAIN" control fully counter clockwise.
3.
When a signal
source
of 0. 5
volts
or
more
is
used
to
drive
the
MC-60,
such
as the
output of a tuner, tape recorder, or other pre-amplifiers, plug the source into the"0. 5 VOLT"
pin jack receptacle or connect to the "0, 5 VOLT" and "GND" screw terminals. Use the
"GAIN" control to obtain the desired operating level.
If desired, the signal source may be wired to an octal plug for insertion in the octal
"Pre-Amp Input" receptacle. In this case connect the input lead to pin #5 and the ground
lead to pin #1. When using this connection the source must not have a DC output component.
Output Connections
The MC-60 has output impedances of 4, 8 and 16 ohms available at either the screw
terminal connector or the output socket. In addition, a 600 ohm output (balanced to ground)
is available at the output socket. See schematic diagram for socket connections.
It is important that the loudspeaker or other load be properly matched to the amplifier
if best performance is to be obtained. Because many loudspeakers do not have voice coil impedances exactly matching
4, 8 and 16
ohms,
the
following table
lists
suggested
connections
for the best impedance matching.
Speaker Impedance
Connect to
3. 2 to 6. 5 ohms
4 ohms
6. 5 to 13 ohms
8 ohms
13 to 32 ohms
16 ohms
WARNING: Output plugs wired for Mclntosh 20W-2 and 50W-2 amplifiers must not be
used with the MC-60 without rewiring the plug.
Output connections for the MC-30 are the same as those for the MC-60.
Power Connections
The
MC-60
operates from
any 110 to 130
volt
50-60
cycles
power
line.
(When
continuous use is contemplated on 120 to 130 line volts the transformer primary should bo re-connected using the 125 volt tap.)
When the MC-60 is used with Mclntosh Pre-Amplifier equipment, tuners, or other
associated equipment, the MC-60 power cord may be plugged into the receptacle at the rear
of these units. When thus connected the power switch of these units controls the MC-60.
GUARANTEE
We guarantee the performance of this equipment arid the mechanical and electrical
workmanship to be free of defects for a period of 90 days. This guarantee does not extend
to components damaged by improper use nor does it extend to transportation to and from the
factory.
SERVICE INFORMATION
All Mclntosh equipment is designed for long trouble free operation. All components
are of the highest quality and are conservatively operated. If trouble develops the amplifier
may be serviced by your franchised dealer, a competent serviceman, or returned to the
factory. Equipment will not be accepted at the factory unless factory return authorization
is first received. The following chart of operating voltages and resistances is offered as a
guide for servicing the unit. All voltages and resistances are measured to chassis except
those with asterick {*). These are measured to chassis with pin #2 of either 5U4GB grounded. Voltages are measured with high impedance VTVM NOTE - UNIT MUST BE TURNED
OFF WHEN MEASURING RESISTANCES.
Tube
12AX7
(Input)
12AU7
12BH7
Pin No.
1
2
3
4 & 5
6, 7, 8
9
1
2
3 & a
4 & 5
6
7
9
1
2
3 & 8
4 & 5
6
7
9
VOLTAGE AND RESISTANCE CHART
DC Volts
No Signal
134
0
1.2
Fil
-
Fil
270
134
138
Fil
270
110
Fil
340
0
16
Fil
340
0
Fil
DC Volts
at 60W out
120
0
1. 1
6. 3 V. ac to pin 9
-
-
235
120
126
6.3V
ac to Pin 9
235
100
_
290
0
14
6. 3V ac to Pin 9
290
0
-
AC Volts
at 60W out
1.5
. 4
.4
-
-
-
11
1.5
0.6
-
11
0
_
148
11
0.32
148
11
-
Resistance
Unit Off
330K*
1M
3.3K
0 to 70
0 to 70
40*
330K*
18K
0 to 70
43K*
2.6M*
0 to 70
12K*
20 OK
1.2K
0 to 70
12K*
200K
0 to 70
Tube
12AX7
KT-88/6550
(Both tube*)
5U4GB
(Both tubes)
Pin No.
1
2
3
4 & 5
6
7
a
9
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
DC Volts
No Signal
435
-46
-45
Fil
435
-46
-45
Fil
0
Fil
435
435
-45
-
Fil
.8
-
440
-
37 5 AC
-
37 5 AC
-
440
DC Volts
at 60W out
365
-46
-45
6.3V
ac to Pin 9
36S
.46
-45
-
0
6. 3V.ac to Pin 7
365
365
-45
-
-
2.5
-
380
-
370AC
-
370AC
-
380
AC Volts
at 60W out
106
148
148
-
106
148
148
-
0
106
110
148
-
110
-
8.9(ripple)
370
370
Resistance
Unit Off
45*
1M
270K
0 to 70
45*
1M
27 OK
0 to 70
-
0 to 70
45*
45*
270K
-
0 to 70
12
-
0*
-
15
-
15
-
0*
Pins not listed are either filaments, have no voltage or are not used.
U. S. Patents No. 2. 477, 074; 2, 545, 788; 2, 646. 467; 2, 654, 058 others pending.
MclNTOSH LABORATORY, INC.
2 Chambers Street
Binghamton, N. Y., U.S.A.
In Canada: Manufactured Under License by McCurdy Radio Industries, Ltd.
22 Front Street West, Toronto, Canada
(0.5V)
(2.5V)
7 & 8
5 & 6
INPUT
ground)
pins
SOCKET
CONNECTIONS
OCTAL
OUTPUT
USING
4 ohms - pins 1 & 2
8 ohms - pins 1 & 3
-
ohms
16 ohms - pins 1 & 4
500/600
pins
ground)
6 is
volts -
6 is CT and
(pin
(pin
70.7
CONNECTIONS
PRE-AMPLIFIER
SOCKET
Input
Pre-Amp
-
- Ground
Pin 2
Pin 1
Pin 3
input
Pre-Amp
- +360V at 3.5 mA
-
- Not used
Pin 4
Pin 5
at 1 Amp
6.3V
- not used
7 & 8 -
Pins
Pin 6
400V
600V
200V
,047mF, 600V
.22mF,
C4
C5
C3 8mF, 250V
600V
.22mF,
.047mF,
C6
C7
500V
500V
35mF,
.47mF, 200V
80mF, 500V
470mF,
.47mF,
.22mF, 600V
C8
C9
C10
C11
C12A
C12B
250V
8mF,
C12C 15mF, 450V
C13A 35mF, 500V
C13B 80mF, 500V
C13C 15mF, 450V
C14
1W
2.2M
18K
100K
R1 250K POT (GAIN ADJ.)
R2
R3 27K
330K
3.3K
100K
680K
R5
R4 1M
R6 68 5%
R7
R8
R9
R10
R11
R12 27K 5%
R13 30K 5%
2W
220K
12K*
R14 220K
R15
R16 330K
R17 12K* 2W
R18
5%
100K
R19 1.2K
R20 56K 5%
R22 1M
R23
R21 1M
R24 56K
R25 56K
5%
1.3K
R26 56K
R27 56K
R28 220 1W
R29 220 1W
R30
*Matched to within 1%
R31 10K 10W
R32 10K 2W
R33 250 OHM POT (HUM ADJ.)
200V
.1mF,
CH1 Plate Choke
CH2 Plate Choke
C1
C2 100mF, 12V
ABOVE
AND
3FB46
NO
SERIAL
038-177
Be102002
Loading...