Mcintosh C1000 schematic

2A

C1000 Preamplifier Rear Panel Connections

CDR (5) RIGHT
Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders

MAIN RIGHT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times

MAIN/SPKR 1 and 2 RIGHT
Channel OUTPUTS (Balanced)
contain Listen signals and may be
assigned either as two additional
Main Outputs (active all the time)
or switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

SPKR 1 and 2 RIGHT Chan
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

-

CD (6), CDR (5)
and D/A (7) RIGHT
Channel INPUTS
(Balanced) accept
high level program
source signals

RECORD LINK INPUTS (Bal­anced) connect to the Record Link
RIGHT Channel Input on the
C1000T Preamplifier when the
C1000P and a C1000T Preampli­fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes

RIGHT PREAMPLIFIER
INPUT A Connector accepts
the custom McIntosh 21
Conductor Cable. This cable
connects to the C1000C
RIGHT CONTROLLER
OUTPUT A. It supplies the
control signals and power
supply voltages for the Right
Channel Circuitry in the
Preamplifier

LEFT PREAMPLIFIER
INPUT B Connector ac
cepts the custom McIn­tosh 21 Conductor Cable.
This cable connects to the
C1000C LEFT CONTROL­LER OUTPUT B. It sup­plies the control signals and
power supply voltages for
the Left Channel Circuitry
in the Preamplifier

­RECORD LINK INPUTS (Bal­anced) connect to the Record
Link LEFT Channel Input on the
C1000T Preamplifier when the
C1000P and a C1000T Preampli­fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes

CD (6), CDR (5) and
D/A (7) LEFT Chan
nel INPUTS (Bal­anced) accept high
level program source
signals

­CDR (5) LEFT

Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders

MAIN LEFT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times

MAIN/SPKR 1 and 2 LEFT
Channel OUTPUTS (Bal­anced) contain Listen signals
and may be assigned either as
two additional Main Out­puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

SPKR 1 and 2 LEFT Chan
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

-

SRVR (4) and CDR (5)
RIGHT Channel OUPTUTS
(Unbalanced) contain the
selected Record Source Signal
for recorders

PROCESSOR RIGHT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode

PROCESSOR RIGHT Channel RECORD
TO and FROM allows an external signal
processor to be connected for use in the
Record mode

TUNER (3), DVD (1), SRVR (4)
and AUX (2), RIGHT Channel
INPUTS (un-balanced) accept
high level program source signals

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: [phone] FAX: [phone] Part No. 04100200

PHONO INPUTS RIGHT MM
(8) accepts signals from a Moving
Magnet Phono Cartridge. MC (9)
Input accepts the low level signals
from a Moving Coil Phono Car
tridge

-

GND (Ground)
connectors for
connecting
the Turntable
Ground Wire
to the C1000P
Chassis

PHONO INPUTS LEFT MM (8)
accepts signals from a Moving
Magnet Phono Cartridge. MC (9)
Input accepts the low level signals
from a Moving Coil Phono Car­tridge

PROCESSOR LEFT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode

TUNER (3), DVD (1), SRVR (4)
and AUX (2), LEFT Channel IN
PUTS (un-balanced) accept high
level program source signals

SRVR (4) and CDR (5) LEFT
Channel OUPTUTS (Unbalanced)
contain the selected Record Source
Signal for recorders

PROCESSOR LEFT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode

-

2B

C1000 Tube Preamplifier Rear Panel Connections

CDR (5) RIGHT
Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders

MAIN RIGHT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times

MAIN/SPKR 1 and 2 RIGHT
Channel OUTPUTS (Bal­anced) contain Listen signals
and may be assigned either as
two additional Main Out­puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

CD (6), CDR (5)
and D/A (7) RIGHT
Channel INPUTS
(Balanced) accept
high level program
source signals

RECORD LINK INPUTS (Bal­anced) connect to the Record
Link RIGHT Channel Input on
the C1000P Preamplifier when the
C1000T and a C1000P Preampli­fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes

RIGHT PREAMPLIFIER
INPUT C INPUT
Connector accepts the cus­tom McIntosh 21 Conductor
Cable. This cable connects
to the C1000C RIGHT
CONTROLLER OUTPUT
C. It supplies the control
signals and power supply
voltages for the Right Chan­nel Circuitry in the Tube
Preamplifier

LEFT PREAMPLIFIER
INPUT D Connector ac­cepts the custom McIn­tosh 21 Conductor Cable.
This cable connects to the
C1000C LEFT CONTROL­LER OUTPUT D. It sup­plies the control signals and
power supply voltages for
the Left Channel Circuitry
in the Tube Preamplifier

RECORD LINK INPUTS (Bal­anced) connects to the Record
Link LEFT Channel Input on the
C1000P Preamplifier when the
C1000T and a C1000P Preampli­fiers are both connected to the
same C1000C Controller, allowing
for the sharing of their inputs for
recording purposes

CD (6), CDR (5) and
D/A (7) LEFT Chan
nel INPUTS (Bal­anced) accept high
level program source
signals

­CDR (5) LEFT

Channel OUPTUTS
(Balanced) contain
the selected Record
Source Signal for
recorders

MAIN LEFT Channel
OUTPUTS (Balanced)
contain Listen program
signals at all times

MAIN/SPKR 1 and 2 LEFT
Channel OUTPUTS (Bal­anced) contain Listen signals
and may be assigned either as
two additional Main Out­puts (active all the time) or
switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

SPKR 1 and 2 RIGHT Channel
OUTPUTS (unbalanced) contain
Listen signals and are switched
On/Off with the Remote Control
SPKR 1 and 2 Push-buttons

SRVR (4) and CDR (5) RIGHT
Channel OUPTUTS (Unbalanced)
contain the selected Record Source
Signal for recorders

PROCESSOR RIGHT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode

PROCESSOR RIGHT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode

TUNER (3), DVD (1), SRVR (4)
and AUX (2), RIGHT Channel
INPUTS (un-balanced) accept
high level program source signals

PHONO INPUTS RIGHT MM
(8) accepts signals from a Mov
ing Magnet Phono Cartridge. MC
(9) Input accepts the low level
signals from a Moving Coil Phono
Cartridge

-

GND (Ground)
connectors for
connecting
the Turntable
Ground Wire
to the C1000T
Chassis

PHONO INPUTS LEFT MM (8)
accepts signals from a Moving
Magnet Phono Cartridge. MC
(9) Input accepts the low level
signals from a Moving Coil Phono
Cartridge

PROCESSOR LEFT Channel RECORD
TO and FROM allow an external signal
processor to be connected for use in the
Record mode

TUNER (3), DVD (1), SRVR (4)
and AUX (2), LEFT Channel IN­PUTS (un-balanced) accept high
level program source signals

SPKR 1 and 2 LEFT Chan
nel OUTPUTS (unbalanced)
contain Listen signals and
are switched On/Off with the
Remote Control SPKR 1 and 2
Push-buttons

SRVR (4) and CDR (5) LEFT
Channel OUPTUTS (Unbalanced)
contains the selected Record
Source Signal for recorders

PROCESSOR LEFT Channel LISTEN
TO and FROM allow an external signal
processor to be connected for use in the
Listen mode

-