Maxdata 2200 IR M7 user manual

MAXDATA PLATINUM 2200 IR – Quick Start Guide

L JK

BA F GEDC

O M L K J HIN G

C D E F

O N

I H

GG F

C D

EB C F GDA

U T

H I

MNS R OPQ

Thank you for buying a MAXDATA PLATINUM 2200 IR Server. This document describes how to set up the system, turn on the system, and complete conﬁguration for the system.

Follow the link “User-Support und Treiber” on www.maxdata.de to access the download area and download a more detailed guide.

Safety

Warning

Installation and service Installation and service of this product is to be performed only by qualiﬁed service personnel to avoid risk of injury from electrical shock or energy hazard.

Enclosure cover In order to comply with applicable safety, emission, and thermal requirements, no covers should be removed and all bays must be ﬁtted with drive carriers.

Battery Safety There is a danger of explosion if the battery is incorrectly replaced. Dispose of used batteries in accordance with the manufacturer’s instructions and national regulations.

Caution

Electrostatic discharge Observe normal Electrostatic Discharge (ESD) procedures during system integration to avoid possible damage to the server board and/or other components of the server system.

Server system power System power on/off: The power button DOES NOT turn off the system AC power. To remove power from server system, you must unplug the AC power cord from the wall outlet or the chassis.

Site Selection

Chassis Components

A. Rack Handles I. System Memory

B. SAS/SATA Backplane J. System Fan Assembly (redundant

C. Air Bafﬂes K. Bridge Board

D. Power Distribution Module L. Control Panel (standard control

E. Power Supply Module Housing

(supports up to two power supply modules)

F. Riser Card Assembly N. Hard Drive Bays

G. Integrated Chassis Intrusion Switch O. Slimline Optical Drive Bay

H. Processor Air Duct

option shown)

panel shown)

M. Flex Bay - 6th HDD or Tape Drive

(optional)

Local Control Panel (optional instead of Standard Control Panel)

A. USB 2.0 Port I. Power/Sleep Button

B. LCD Display J. System Status LED

C. Menu Control Button, Scroll Up K. NIC 2 Activity LED

D. Menu Control Button, Scroll Down L. NIC 1 Activity LED

E. Menu Control Button, Scroll Left M. Hard Disk Activity LED

F. Menu Control Button, Enter N. Reset Button

G. System Identiﬁcation LED O. USB 2.0 Port

H. Power/Sleep LED

Rear of Server System

A. Low Proﬁle Add-in Card Slots I. NIC 1

B. Full Height PCI Add-in Card Slots J. NIC 2

C. Upper Power Supply Module K. USB 6

D. Upper Power Receptacle L. USB 5

E. Lower Power Receptacle M. DB-9 Serial A Connector

F. Lower Power Supply Module (optional) N. Video

G. I/O Module (optional) O. RJ45 Serial B Connector

H. Server Management NIC (optional)

Server Board Connector and Component Locations

The system is designed to operate in a typical ofﬁce environment. Choose a site that is:

• Clean, dry, and free of airborne particles (other than normal room dust).

• Well-ventilated and away from sources of heat including direct sunlight and radiators.

• Away from sources of vibration or physical shock.

• Isolated from strong electromagnetic ﬁelds produced by electrical devices.

• In regions that are susceptible to electrical storms, we recommend you plug your system into a surge suppresser and disconnect telecommunication lines to your modem during an electrical storm.

• Provided with a properly grounded wall outlet.

• Provided with sufﬁcient space to access the power supply cord(s), because they serve as the product’s main power disconnect.

Standard Control Panel

System Overview

Technical Speciﬁcation

Dimensions:

- 87.30 mm high

- 430 mm wide

- 704.8 mm deep

- 29.5 kg - max chassis weight

System Power:

- 100-127 V at 50/60 Hz; 12 A max.

- 200-240 V at 50/60 Hz; 6 A max.

Temperature Range: +10 °C to +30 °C

Regulatory Compliance

This product complies to the following requirements:

- EN 60950 – Safety

- EN 55022 – Emissions

- EN 55024 – Immunity

- EN 61000-3-2 – Harmonics

- EN 61000-3-3 – Voltage Flicker

- CE – EMC Directive 89/336/EEC

This product has a CE declaration of conformity (CENELEC Europe). This server system is compliant to European Directive 2002/95/EC (RoHS).

MAXDATA PLATINUM 2200 IR M7 Quick Start Guide

A. NIC 2 Activity LED G. System Identiﬁcation LED

B. NIC 1 Activity LED H. System Identiﬁcation Button

C. Power/Sleep Button I. Reset Button

D. Power/Sleep LED J. USB 2.0 Port

E. Hard Disk Drive Activity LED K. NMI Button

F. System Status LED L. Video Port

A. 280-pin Intel® Adaptive Riser Card slot Q. Fan board connector

B. POST code LEDs R. 2×4 power connector

C. Intel® RMM3 header S. Main power connector

D. Processor 1 T. Power supply SMBus connector

E. Back panel I/O U. Fan header

F. ID LED V. USB header

G. System status LED W. Solid state drive header

H. Fan header X. Fan header

I. Fan header Y. LCP IPMB header

J. Processor 1 DIMM slots Z. OEM IPMB header

K. Processor 2 DIMM slots AA. SGPIO header

L. Processor 2 BB. SATA connectors

M. Fan header CC. I/O module mezzanine connector 2

N. Fan header DD. I/O module mezzanine connector 1

O. Bridge board connector EE. Serial port B header

P. Front panel connector

3 2

Removing the Front Bezel

Unlock the bezel and pull it from the server system.

Installing the Server System Cover

Place the cover over the server system so that the side edges of the cover sit just inside the server system sidewalls.

Slide the cover forward until it clicks into place (see letter “A”).

Installing the PCI Add-in Card Riser Assembly

Align the three hooks in the riser assembly with the matching slots at the back of the server system (see letter “B”).

Press down uniformly until the three hooks on the rear of the PCI riser assembly engage the server system back panel slots. The riser cards will seat into the matching sockets on the server board.

Install the Carrier Assembly.

Note Carrier lever must be held in the FULLY OPEN position to install into chassis. Slide carrier into chassis until it stops, then rotate the lever until it snaps shut.

Installing the Front Bezel

Push the bezel onto the front of the server system until it clicks into place.

Removing and Installing the Processor Air Duct

Installing a PCI Add-in Card

Open the rear retention clip by pushing the blue slide upward and rotating clip to the fully open position (see letter “A”).

Open the front retention clip by rotating 90 degrees outward (see letter “B”).

Remove the ﬁller panel from the selected add-in card slot (see letter “C”).

Insert add-in card until it seats in riser card connector (see letter “D”).

Close both retention clips.

Installing Hard Drives

Remove the Plastic Air Bafﬂe.

Hard Drive Numbering Diagram

Drive 0 Primary Drive Bay

Caution If you install less than 6 drives or devices, empty drive bays must be occupied by carriers with bafﬂes to maintain proper system cooling. To avoid possible damage to your chassis, use only carriers that came with your server system.

Replacing the Power Supply

If a power supply is installed, release the latch and remove the power supply by pulling on the handle as shown in the ﬁgure below.

Removing the Server System Cover

Remove the safety screw if it is installed. See letter “A” in the ﬁgure below.

While holding in the blue button at the top of the server system in (see letter “B”), slide the top cover back until it stops (see letter “C”).

Insert your ﬁnger in the notch (see letter “D”) and lift the cover upward to remove it.

Removing the PCI Add-in Card Riser Assembly

Grasp both riser latches with thumb and foreﬁnger (see letter “A”), and pull up to release riser assembly.

Lift riser assembly straight up (see letter “B”).

Bafﬂe

Insert the replacement power supply module into the power supply cage until it clicks into place.

Drive Carrier

Install the Hard Disk Drive.

MAXDATA PLATINUM 2200 IR M7 Quick Start Guide

Attach with four screws

Maxdata 2200 IR M7 user manual

Specifications and Main Features

Frequently Asked Questions

User Manual