Model MOUNT20 User Guide
For VP-11/12/15 Series Projector
IMPORTANT SAFETY INSTRUCTIONS
READ BEFORE INSTALLING EQUIPMENT
This product was designed and manufactured to meet strict
quality and safety standards. There are, however, some
installation and operation precautions which you should be
particularly aware of.
1.
Read instructions -
should be read before the product is operated.
2.
Retain instructions -
should be retained for future reference.
3.
Heed warnings -
operating instructions should be adhered to.
4.
Follow instructions -
be followed.
5.
Use only the parts provided with the mount, along with any
parts (commercially available) that are specified in this manual.
6.
Do not modify the mount or the parts provided with the mount.
7.
Do not use damaged parts. if any parts become damaged,
contact your dealer.
8.
All bolts and screws must be tightened securely.
9.
Make sure not to block any ventilation openings when installing
the projector.
10.
Special techniques and experience are required when installing
the projector with this mount. Contact your dealer to install the
projector for you.
11.
Once the projector is installed, safety checks should be conducted
on a regular basis.
All the safety and operating instructions
The safety and operating instructions
All warnings on the product and in the
All installation instructions should
MOUNT20
PROJECTOR MOUNT
INSTALLATION INSTRUCTIONS
Step 1
Base Plate Connectors #1 and Projector Mount Ceiling
Plate 1 with
Figure 1
ceiling mounting holes #2.
1
4
2
3 3
Ceiling Wire
Access
4
2
8 5/8"
Plate 1
Base Plate Connectors #1
Projector Mount Ceiling Plate 1
Insert Base Plate connectors #1 into the lateral positioning slots
#
3 as shown in #4 from the underside of Plate 1. The lateral positioning
slots will give you 2 1/4" inches of lateral adjustment for projector
alignment.
14"
2
Warning
The ceiling should be capable of supporting a weight
of at least five (5) times the projector(s) weight.
If it cannot, the ceiling must be reinforced. Proper
installation procedure by qualified personnel as outlined
in the installation instructions must be adhered to.
Failure to do so could result in serious personal injury.
Hardware List
1. Four (4) 3/8 (inch) nuts
2. Four (4) 3/8 (inch) flat washers
3. Two (2) 8 (mm) screws
4. Eleven (1
5. Eight (8) 6 (mm) rubber washers
1) 6 (mm) screws
Adjustment Ranges and Load Allowances
Horizontal Tilt (yaw) +/- 10 degrees
Vertical Tilt (tilt) +/- 20 degrees
Rotation +/- 15 degrees
Lateral Shift +/- 2
Maximum Load Allowance 450 Lbs.
6. One (1) Ceiling Mount #1
7. Two (2) Base Plate Connectors
8. One (1) Horizontal
9. One (1) Horizontal
10. One (1) Projector Plate #4
Tilt Plate #2
Tilt Plate #3
1/4
inches
Step 2
Horizontal Adjustment Plate 2 (Base Plate Connector
Holes #3).
Figure 2
3
Wire
Access
3
7 5/8"
Plate 2
Base plate connector holes #3 provide 15 degrees of horizontal
rotation adjustment.
Attach horizontal adjustment Plate 2 to projector mount ceiling
Plate 1 using the four (4) 3/8" (inch) nuts and washers provided.
3
10 5/8"
3
MOUNT20 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued
Step 2 B
Horizontal Adjustment Plate 2 (Figure 2) attached to
Projector Mount Ceiling Plate 1.
Step 3 B
Horizontal Tilting Plate 3 Attached to Plates 1 and 2.
Figure 3
Wire
Access
Plates 1 & 2
Install the combined plates (above) securely to the ceiling
structure in accordance with local commercial building
standards.
Figure 5
Tilting Capability
Plate 3
The newly combined Plate 3 provides 10
horizontal tilt. When positioned, tighten with screws
provided.
Use suitable hardware in adequate quantity and size depending
on the installation requirements. (Please note that Projector
VP-12SX weighs 28.6 lbs. (13 kgs).
Step 3
Step 4
Horizontal Tilting Plate 3 Projector Mounting Plate 4
Tilting Capability
0
degrees of
Figure 4
2
2
1
2
2 2
1
Holes for 6mm screws with rubber washer and steel washer
2
Holes for 6mm screws
3
Holes for 8mm screws
Plate 3
3
Wire
Access
Indicates Forward
Positioning of Mount
3
2
2
1
2
Attach Horizontal Tilting Plate 3 to the previously combined
plates (already installed on ceiling) using the two (2) 8 (mm)
screws and four (4) 6
in Figure
4. Install two (2) 6 (mm) screws with rubber
(mm) screws provided, as indicated
spacers and metal washers into the welded metal studs
#1).
(indicated
Figure 6
Indicates Forward
Positioning of Mount
17"
12 1/4"
mounting holes
Plate 4
Invert the projector and place it on a soft and flat
surface. Align the three (3) rubber spacers provided
with the three (3) 6(mm) mounting holes on the
projector and secure with three (3) 6(mm) screws
provided.
continued over
MOUNT20 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued
Step 4 B
Projector Mounting Plate 4 (continued)
Projector Mounting Plate 4 connected to Mounting Plate 3
Figure 7
Plate 4
20
0
Tilt
CEILING
Mount Side
Projector Side
20
0
Tilt
Work in a group of 2 or more to carry the projector and follow
manufacturer's guidelines for relocating as stated in the VP-12SX
owner's manual.
Lift and slide the projector onto the 6 (mm) screws previously
installed in the metal studs of the plate on the ceiling (see arrow
in Figure 7). Tighten the 6 (mm) screws on both sides of the
mount and install four (4) 6 (mm) screws and washers into the
side of the projector Mounting Plate 4.
Figure 8
Mounts Fully Assembled
Ceiling Side
Projector Side
Sequence of Assembly of Projector Mounting Plates
Plate 1
Step 2
Plate 2
Step 3
Plate 3
Step 4
Plate 4
Mahwah
, NJ 07430
Phone: 201 762-6500
You can find your nearest authorized distributor or dealer
on our website at: www.marantz.com
Printed in Canada
100 Corporate Drive
2008
Marantz Templates
Base Plate Connectors
6.50"
TOP VIEW
PLATE #1
8.125"
1.125"
1.5"
3.375"
1.5"
1.125"
5.700
5.00"
2.750"
10.250"
5.625"
4.250"
1.750"
1.375"
1.5" 1.5"5.625" 5.625"
3.812"
.500"
7.00"
END VIEW
PLATE #1
14.00"
CEILING SIDE
1.125" 1.125"
1.5" 1.5"
3.375"
7/8"
Mahwah
, NJ 07430
Phone: 201 762-6500
100 Corporate Drive,
You can find your nearest authorized distributor or dealer
on our website at: www.marantz.com
Printed in Canada
2008
13.2"(335.5mm)
MOUNT20Dimensions
+/‑10degree
+/‑15degree
+/‑60mm
+/‑20degree
4.05"(103.0mm)
Loading...