Marantz DR-6050 Owners Manual

Model DR6050 User Guide
Compact Disc Recorder
R
CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT
Recordable
ReWritable
INTRODUCTION
ReWritable
Foreword
This section must be read carefully before any connection is made to the mains supply.
WARNINGS
Do not expose the equipment to rain or moisture. Do not remove the cover from the equipment. Do not insert anything into the equipment through the
ventilation holes. Do not handle the mains lead with wet hands.
CE marking (only EU version)
This product is in conformity with the EMC directive and low-voltage directive.
Equipment mains working system
Your Marantz product complies with the household power and safety requirements in your area. /N1 Version product can be powered by 230 V AC only.
IMPORTANT: (FOR/UK. version only)
This apparatus is fitted with an approved moulded 13 Amp plug. To change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.
Note :
The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.
HOW TO CONNECT A PLUG
The wires in the mains lead are coloured in accordance with the following code: BLUE—“NEUTRAL (“N”) BROWN—“LIVE (“L”)
1. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK.
2. The BROWN wire must be connected to the terminal which is marked with the letter “L” or coloured RED.
3. Do not connect either wires to the earth terminal in the plug which is marked by the letter “E” or by the safety earth symbol or coloured green or green-and-yellow.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead not simply over the two wires.
Copyright
Recording and playback of some material may require permis­sion. For further information refer to the following:
- Copyright Act 1956
- Dramatic and Musical Performers Act 1958
- Performers Protection Acts 1963 and 1972
- Any subsequent statutory enactments and orders
Congratulations on the acquisition of your CD-Recorder. This CD-Recorder now enables you to record, play and erase your own audio Compact Discs. Naturally the recorder can also be used to play all pre-recorded CDs.
With the exception of legal restrictions pertaining to copying, you can now create your own high-quality audio recordings on CD. The discs used to record must bear the logos shown be­low. Copyright fees have been paid on these discs in some countries. Recording on other types of discs (e.g. CD-R for pro­fessional recordings) is not possible.
There are two types of recordable AUDIO discs: CD-R(W) discs have a compatibility to play/record on the CD­Recorders based on the ORENGE BOOK Part II/III. But the discs might not be able to be played/recorded properly depend­ing on the combinations of the discs and CD-Recorders.
1 CD Recordable Audio (record once):
Fully recorded and subsequently finalized audio CD-R discs can be played on all CD players and recorders that are suit­able for CD-R discs. A CD-R disc can be recognized by the following logo:
Recordable
2 CD ReWritable Audio (multiple recording):
Recorded and finalized audio CD-RW discs can be played on all CD players and recorders that are suitable for CD-RW discs. An increasing number of players and recorders will be suitable for these discs in the future. A CD-RW disc can be recognized by the following logo:
The CD-R(W)disc for ‘DIGITAL AUDIO’ can be both recording and playing on this CD-Recorder. In addition, this CD-Re­corder can play the CD-R(W) disc for ‘PROFESSIONAL RE­CORDING’, but cannot record it.
Once you start using the recorder, you will discover how easy it is to ‘make’ your own CDs. Nevertheless, we recommend that you use an erasable (CD-RW) digital audio disc on your first attempt, while following the instructions given here.
Recordable
ReWritable
Attention!
Recordings may only be made for personal use. It is forbidden to copy material protected by copyright, in-
cluding computer programs, films, television and audio recordings. This appliance may not be used for applica­tions of this type.
Note:
Some CD players can not play the finalized CD-R(W) discs be­cause of the low reflectivity of such discs.
Because of laser power differences, some DVD players cannot play the finalized CD-R(W) discs.
ENGLISH
Read the text carefully and keep the instructions close at hand so that you can refer to them if necessary.
1
ENGLISH
INTRODUCTION
Unpacking
First check the contents of the packaging. It should contain the following:
- CD-Recorder DR6050
- Remote control with batteries packaged separately
- Audio cables (2 - with red and white plugs)
- Remote control cable (with orange plugs)
- Instructions
- Guarantee
If one of these components is missing, please inform your sup­plier immediately. Save the packaging material it may come in handy if you move the appliance.
Setup
- Place the recorder on a strong, vibration-free surface.
- Do not use the recorder under extremely damp condi-
tions.
- If the recorder is placed in a cabinet, make sure that a
2.5 cm space remains free on all sides of the recorder for proper ventilation.
Attention!
If the appliance is not used or operated in accordance with the instructions, this may result in exposure to dangerous radiation or other risks.
Only authorized technicians are allowed to open the appli­ance casing or to perform repairs or maintenance.
Do not use conventional record cleaner for analog records, as this will adversely affect the disc surface. Store discs properly by placing them in their disc cases.
Do not attach a piece of paper or sticker on the label side of disc. When a disc has a piece of plastic tape or rental CD label with paste protruded from the edge or when a disc has a trace of such a sticky object, do not attempt to play the disc. If such a disc is played on the CD player, impossibility of tak­ing out the disc or other malfunction may result.
Write only on the printed side of a CD-R or CD-RW, and only with a soft felt-tipped pen.
Do not use a disc with a special shape. Do not attempt to play a disc with a special shape such as a
heart-shaped disc or octagonal disc. Otherwise the equip­ment malfunction may result.
Compact discs
The glossy side shining like a rainbow is the front side of the disc, and the side on which the label is printed is the back. Unlike conventional turntables for playing analog discs, the DR6050 reads the information recorded on the disc from under­neath without contacting it using a beam of laser light. There­fore, the performance of a compact disc will not degrade like conventional analog records.
Handle discs carefully so as not to damage or scratch the front side.
To protect the disc, avoid placing it in the following loca­tions:
- In direct sunlight or near a source of heat like a heater.
- In a place which is damp or dirty.
- In a place which could be exposed to rain, such as near a window.
Always keep the disc surface clean.
Up to six billion data units are recorded on the front side of the disc. When cleaning the disc surface, always be sure to use a special compact disc cleaner and wipe as shown below.
Maintenance
Clean the CD-Recorder with a soft, slightly dampened lint-free cloth. Do not use any cleaning agents as they may have a cor­rosive effect.
Do not expose the CD-Recorder, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight).
C D R
E C O R
D E R
D R
6 0 5 0
R e c o r d
a b l
e
R e W r i
t a b l
e
P O W E
R
O N /
O F F
S
T O P
P L A Y
/ P A U S
E
O P
R
E
E
N
C
/
S T O R E
/
M E N U
E A S Y
C
J
L
O
O
G S E
C D R
C A N C E L
/
D E L E T
E O P E N / C L O S E
S T O P
P L A Y
/ P A U S
E
R E C T Y
P E
S O
C
U
D
R C
E
E R A S E
F I
N A L I
Z
E
D J M O D
E
P H O N E S
P U S H E
N T E R
If the CD-Recorder cannot read CDs correctly use a commonly available cleaning CD to clean the lens before taking the CD player to be repaired. Other cleaning methods may destroy the lens. Always keep the tray closed to avoid dust on the lens.
The lenses may cloud over when the CD-Recorder is suddenly moved from cold to warm surroundings. It is not possible to play a CD then. Leave the CD-Recorder in a warm environment until the moisture evaporates.
2
CONTROLS AND CONNECTIONS
Controls on the front
CD-Recorder
(1) POWER ON/OFF ...........
(2) Standby indicator
(3) Disc tray (Deck1) .......... records CD-R(W) and plays CD
(4) 0 REC (ord)...................
(5) 9 STOP ..........................stops/clears a program
(6) 2/; PLAY/PAUSE .......... starts play/interrupts play or re-
(7) CDR ............................... selects CDR display/keys (left
(8) CDR INDICATOR
(9) / OPEN/CLOSE ............opens/closes disc tray
(11) REC (ord) TYPE ............ selects recording modes
(12) SOURCE ........................ selects external input source
(13) ERASE ........................... selects erasing mode
(14) FINALIZE ....................... selects finalize mode General
turns the CD-Recorder ON and OFF
and CD-R(W) starts recording, finalizing, erasing
cording side)
General
(10) Q ................................ - searches backward
- cursor control in Menu/Prog. re­view mode
(15) R ................................ - searches forward
- cursor control in Menu/Prog. re­view mode
(16) Display .......................... information screen
(17) DJ MODE ....................... separate play of CD-Recorder
and CD player
(18) STORE/MENU ............... -enters Menu mode
- stores Menu settings
(19) – EASY JOG +............... - previous/next track (Play and
Program mode)
- recording level control (recording)
- selects settings (menu on)
PUSH/ENTER ................ - plays selected tracks
(push) ............................- selects settings in Menu mode
- programs track numbers
(20) CANCEL/DELETE ......... - deletes tracks from a program
- deletes text in Menu mode
- returns to a higher level in the menu
(21) PHONES ........................ socket for headphones
unavailable to adjust the volume
CD player
(22) Disc tray (Deck2) .......... plays CD and CD-R(W)
(23) 2/; PLAY/PAUSE .......... starts play/interrupts play
(24) 9 STOP .......................... stops/clears a program
(25) CD INDICATOR
(26) CD .................................. selects CD display/keys
(27) / OPEN/CLOSE ............ opens/closes disc tray
Note:
- When provided on the remote control, you can also use the corresponding buttons, after selecting the CD-Recorder or
CDR
(73) or
CD
CD Player by pressing
- Some buttons are only on the remote control.
(84).
Connections at the back
(28) ANALOG INPUT ............ connects to the line output of an
amplifier (left and right)
(29)
ANALOG OUTPUT CDR / CD
(30) ANALOG OUTPUT CD..
...connects to the line input of an
amplifier (left and right) connects CD player deck to the line input of an amplifier (left and right)
(31) DIGITAL INPUT ............. connects to the digital coaxial
DIGITAL OUTPUT CDR / CD
(32) (33) DIGITAL OUTPUT CD ...connects CD player deck to the
(34) OPTICAL INPUT............ connects to the digital optical
OPTICAL OUTPUT CDR / CD
(35)
OPTICAL OUTPUT CD
(36)
REMOTE CONTROL OUT
(37)
REMOTE CONTROL IN
(38) (39)
REMOTE CONTROL SWITCH
(40) AC POWER CABLE
DISPLAY indications
(41) REM/REC TIME ............. remaining recording time / re-
(42) TRACK........................... track number
(43) (44) TOTAL REM
TRACK TIME ................. total or remaining time of disc or
(45) STEP ..............................indicates the number of tracks in
(46) 20 + ................................disc or program contains more
(47) Track Number ............... tracks on a discs or in a program
(48) PROGRAM .................... flashes during programming/
(49) RANDOM ALL ............... plays tracks in random order
(50) SCAN ............................. lights up when the first 10 sec-
(51) REPEAT TRACK/ALL ... lights up when a track/ complete (52)
(53) CD .................................. CD inserted (a pre-recorded CD
(54) .................changer mode selected
(DJ MODE SELECT)
(55)
(56) L/R .................................record/play level bar. Indicates
(57) 1 DUBBING ................... lights during recording from the
(58) 2 .....................................lights during play
(59) R (W) ..............................unfinalized CD-R(W) disc in-
(60) 0 ....................................lights during recording
(61) ; ..................................... pause function active
(62)
(63) ..................analog input selected for external
(64) MANUAL........................ lights up when auto track mode is
3
output of an external CD player
....
connects to the digital coaxial input of e.g. amplifier or recording device
digital coaxial input of e.g. ampli­fier or recording device
output of an external CD player
...connects to the digital optical in-
put of e.g. amplifier or recording device
...connects CD player deck to the
digital optical input of e.g. ampli­fier or recording device
.....connects to a remote control in-
put on the Marantz amplifier
....connects to a remote control out-
put on the Marantz amplifier
cording time
...............................balance (lights during balance
adjustment)
track a program than 20 tracks track in play lights in program mode
onds of each track are played. disc (or program) is repeated.
...................................CD player selected
or finalized CD-R or CD-RW disc)
.....DJ mode selected
the audio signal level. internal CD
serted
..........................optical input I selected for exter-
nal recording recording
........................analog recording
turned off
ENGLISH
ENGLISH
(65) SYNC ............................. automatic or synchronized start
of external recording
(66)
REMOTE CONTROL
Remote control commands
(67) STANDBY ................. switches to Standby/On/Off
(68) TRACK INCR. (ement) ..increases track numbers during
(69) SCAN ............................. plays the first 10 seconds of each
(70) REPEAT......................... repeat play(All, program or track)
Number/alphabet keys 0 - 9 ..
(71)
(72) DISPLAY........................ selects display information/text
(73) CDR ............................... selects CD-Recorder
(74) 2 .....................................starts CD-R(W) play
(75) S ................................ previous track (Play and Pro-
(76) Q ................................ - searches backward
(77) ; .....................................
(78) MENU/STORE ............... - enters Menu mode
(79) ENTER ........................... - selects settings in Menu mode
(80) CANCEL/DELETE ......... - deletes tracks from a program
(81) R ................................ - searches forward
(82) 9 .....................................stops CD-R(W) and clears a pro-
(83) T ................................ next track (Play and Program
(84) CD .................................. selects CD player
(85) SCROLL ........................ activates scrolling of text over the
(86) PROG. (ram).................. opens/closes program memory
(87) RANDOM ....................... plays CD-R(W) or program in
........................digital input I selected for external
recording
recording track
- selects a track by number
- selects character for text input
gram mode)
- cursor control in Menu/Prog. re­view mode
interrupts CD-R(W) play/record­ing
- stores Menu settings
- programs track numbers
- starts playback of selected track
- deletes text in Menu mode
- returns to a higher level in the menu
- cursor control in Menu/Prog. re­view mode
gram mode)
display
random order
4
INSTALLATION
This CD-Recorder can be used to record directly or through a (pre-) amplifier from any digital or analog audio source. In addition, the appliance can be used as a regular CD player. Read how to connect the CD-Recorder based on the possibili­ties your other audio equipment offers. Please refer to the operating instructions for your other audio equipment first.
The following options are available:
- analog connections
- digital coaxial connections
- digital optical connections
Analog connections
For recording and playing, connect (using the enclosed cable with red and white plugs) the CD-Recorder to an amplifier (pref­erably the CD-Recorder or TAPE connection) based on the dia­gram below:
CD RECORDER DR6050
Recordable
ReWritable
POWER ON/OFF
REC
PLAY/PAUSESTOP
CDR
L
R
INPUT
OPEN/ CLOSE
SOURCEREC TYPE
ANALOG IN/OUT
CDR/CD
OUTPUT
OPEN/ CLOSE
ERASE FINALIZE
CD
1
L
L
R
OUTPUT
R
INPUT
Amplifier 1
1 For recording, connect cable q between the ANALOG IN-
PUT-sockets on the CD-Recorder and the CD LINE- or TAPE OUTPUT-sockets of an amplifier.
PLAY/PAUSESTOP
CD DJ MODE
EASY JOG
CANCEL/DELETESTORE/MENU
PHONES
PUSH ENTER
2
3
L
R
INPUT
Amplifier 2
Digital Coaxial connections
For recording and playing, connect (using the suitable coaxial cable, available from your supplier) the CD-Recorder to a dig­ital amplifier or other equipments based on the diagram below:
CD RECORDER DR6050
Recordable
ReWritable
POWER ON/OFF
REC
OPEN/ CLOSE
SOURCEREC TYPE
COAXIAL
CDR/CD CD
OUTPUT
OPEN/ CLOSE
ERASE FINALIZE
PLAY/PAUSESTOP
CDR
INPUT
456
OUTPUT INPUT INPUT
Amplifier 1
1 For an external recording, connect the cable r between
the DIGITAL INPUT-socket on the CD-Recorder and the DIGITAL OUTPUT-socket of an external amplifier or CD player.
2 For playback, connect cable t between the DIGITAL CDR/
CD OUTPUT-socket on the CD-Recorder and the DIG­ITAL INPUT-socket of an amplifier e.g. CD or AUX.
3 For DJ-Mode playback (See page 15), connect cable y be-
tween the DIGITAL CD OUTPUT-socket on the CD-Re-
corder and the DIGITAL INPUT-socket of an amplifier e.g. CD or AUX.
- DJ-Mode playback is the function that the deck 1 and the deck 2 on this CD-Recorder can play the songs separately at the same time.
PLAY/PAUSESTOP
CD DJ MODE
EASY JOG
CANCEL/DELETESTORE/MENU
PHONES
PUSH ENTER
Amplifier 2
ENGLISH
2 For playback, connect cable w between the ANALOG
CDR/CD OUTPUT-sockets on the CD-Recorder and the ANALOG INPUT-sockets of an amplifier e.g. TAPE IN, CD or AUX.
3 For DJ-Mode playback (See page 15), connect cable e be-
tween the ANALOG CD OUTPUT-sockets on the CD-Re-
corder and the ANALOG INPUT sockets of an amplifier e.g. TAPE IN, CD or AUX.
- DJ-Mode playback is the function that the deck 1 and the deck 2 on this CD-Recorder can play the songs separately at the same time.
Note:
Never use the PHONE input.
5
ENGLISH
INSTALLATION D-BUS CONNECTION
Digital Optical connections
For recording and playing, connect (using the suitable fiber-op­tic cable, available from your supplier) the CD-Recorder to a digital amplifier or other equipments based on the diagram be­low. Before connection the cables, remove the dust caps from the digital optical connections. We recommend that you save the caps.
CD RECORDER DR6050
Recordable
ReWritable
POWER ON/OFF
REC
PLAY/PAUSESTOP
CDR
INPUT OUTPUT
OPEN/ CLOSE
SOURCEREC TYPE
OPTICAL
CDR/CD CD
OPEN/ CLOSE
ERASE FINALIZE
789
OUTPUT INPUT INPUT
Amplifier 1 Amplifier 2
1 For external recording, connect a fiber-optic cable u be-
tween the DIGITAL OPTICAL INPUT of the CD-Recorder
and the DIGITAL OPTICAL OUTPUT of an external ampli­fier or CD player.
PLAY/PAUSESTOP
CD DJ MODE
EASY JOG
CANCEL/DELETESTORE/MENU
PHONES
PUSH ENTER
Remote control cable connections
By connecting DR6050 to the Marantz amplifier using a D-BUS remote control cable 0, you can operate the operations of DR6050 from the remote control of the amplifier. Set the re-
mote control selector to EXTERNAL’.
Note:
When you dont use the D-BUS connection, ALWAYS set the remote control selector to ‘INTERNAL’.
CD RECORDER DR6050
Recordable
ReWritable
POWER ON/OFF
REC
OPEN/
PLAY/PAUSESTOP
CLOSE
CDR
Marantz Amplifier
SOURCEREC TYPE
REMOTE
CONTROL
IN
OUT
REMOTE
CONTROL
IN
EASY JOG
OPEN/ CLOSE
CD DJ MODE
ERASE FINALIZE
INTERNALEXTERNAL
CANCEL/DELETESTORE/MENU
PLAY/PAUSESTOP
PHONES
PUSH ENTER
10
OUT
2 For playback, connect cable i between the OPTICAL CD/
CDR OUTPUT-socket on the CD-Recorder and the DIG­ITAL OPTICAL INPUT-socket of an amplifier e.g. CD or AUX.
3 For DJ-Mode playback (See page 15), connect a fiber-optic
cable o between the OPTICAL CD OUTPUT-socket on
the CD-Recorder and the DIGITAL OPTICAL INPUT­socket of an amplifier e.g. CD or AUX.
- DJ-Mode playback is the function that the deck 1 and the deck 2 on this CD-Recorder can play the songs separately at the same time.
Note:
For playback, the digital coaxial outputs or analog outputs of the CD Player and CD-Recorder should be connected to an amplifier
6
Loading...
+ 19 hidden pages