OWNER’S MANUAL
LED LCD TV
Please read this manual carefully before operating your set and retain it for future reference.
LT36**
www.lg.com
ENGLISH
2 TABLE OF CONTENTS
3 LICENSES
3OPEN SOURCE SOFTWARE NOTICE
4INSTALLATION PROCEDURE
4 ASSEMBLING AND PREPARING
4 Unpacking
7Parts and buttons
8Lifting and moving the TV
9Setting up the TV
9 - Attaching the stand
11- Mounting on a table
12- Mounting on a wall
14- Tidying cables
15 MAKING CONNECTIONS
15Adapter connection
15Antenna connection
16HDMI connection
16DVI to HDMI connection
17RGB-PC connection
17 RS-232C Setup
17Component connection
18Composite connection
18Speaker output SETUP
18USB connection
19CI module connection
19Euro Scart connection
20REMOTE CONTROL
21MAINTENANCE
21 Cleaning your TV
21 - Screen, frame, cabinet and stand
21 - Power cord
21TROUBLESHOOTING
22SPECIFICATIONS
25 EXTERNAL CONTROL DEVICE SETUP
25RS-232C Setup
25Type of connector; D-Sub 9-Pin Male
25RS-232C Configurations
26Communication Parameters
26Command reference list
27Transmission / Receiving Protocol
WARNING
yyIf you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
CAUTION
yyIf you ignore the caution message, you may be slightly injured or the product may be damaged.
NOTE
yyThe note helps you understand and use the product safely. Please read the note carefully before using the product.
24 IR CODES
LICENSES / OPEN SOURCE SOFTWARE NOTICE 3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.”
Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274
ENGLISH
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
ENGLISH
4 INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
NOTE
yyImage shown may differ from your TV.
yyYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yyThe available menus and options may differ from the input source or product model that you are using.
yyNew features may be added to this TV in the future.
yyThe TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned off if it will not be watched for some time, as this will reduce energy consumption.
yyThe energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost.
1Open the package and make sure all the accessories are included.
2Attach the stand to the TV set.
3Connect an external device to the TV set.
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yyDo not use any unapproved items to ensure the safety and product life span.
yyAny damages or injuries by using unapproved items are not covered by the manufacturer’s warranty. yySome models have a thin film attached on to the screen and this must not be removed.
NOTE
yyThe items supplied with your product may vary depending on the model.
yyProduct specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.
yyFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.
|
B |
B |
|
|
*A = |
10 mm |
|
|
|
< |
|
|
|
< |
18 mm |
|
|
*B = |
|
A |
|
A |
|
ASSEMBLING AND PREPARING 5
Q.VIEW |
SETTINGS Q.MENU
P |
EXIT |
Remote control and |
|
|
batteries (AAA) |
|
|
(See p.20) |
Cable Holder
(Depending on model)
(See p.14)
Stand Screws
4 EA, M4 x 12
2 EA, M4 x 16
(Only 22LT36**)(See p.9)
Stand Screws
8 EA, M4 x 14
(Only 32/37/42/47LT36**) (See p.10)
Power cord
Stand body / Stand base
(Only 22LT36**)
(See p.9)
|
Stand body / Stand base |
|
|
(Only 32/37/42/47LT36**) |
|
|
(See p.10) |
|
or |
Isolator |
|
(Depending on model) |
||
|
||
|
(See p.6) |
Owner’s manual
Power Cord holder
(Only 32/37/42/47LT36**)
(See p.14)
Stand Screws
8 EA, M4 x 12
(Only 26LT36**)(See p.9)
Desk-mount Screw
1 EA
(Only 32/37/42/47LT36**) (See p.11)
DC Adapter
(Only 22/26LT36**) (See p.15)
Stand body / Stand base
(Only 26LT36**)
(See p.9)
Protection cover
(Only 32/37/42/47LT36**) (See p.13)
ENGLISH
ENGLISH
6 ASSEMBLING AND PREPARING
NOTE
yyAntenna Isolator Installation Guide
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
Wall
ANTENNA/
or
Cable / Antenna
Isolator
1.Connect to TV.
2.Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING 7
(Only 32/37/42/47LT36**)
PCMCIA Card Slot
COMPONENT IN |
COMPONENT IN |
|
|
USB input |
USB IN |
HDMI IN |
IN 3 |
|
Remote control
Power Indicator (Can be adjusted using the Power Indicator in the OPTION menu.)
Screen
(Only 22/26LT36** )
Speakers
ENGLISH
Button |
Description |
|
Scrolls through the saved programmes. |
|
|
- + |
Adjusts the volume level. |
|
|
|
Turns the power on or off. |
|
|
ENGLISH
8 ASSEMBLING AND PREPARING
When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.
yy When transporting a large TV, there should be at least 2 people.
yy When transporting the TV by hand, hold the TV as shown in the following illustration.
CAUTION
yyAvoid touching the screen at all times, as this may result in damage to the screen.
yy It is recommended to move the TV in the box or packing material that the TV originally came in.
yy Before moving or lifting the TV, disconnect the power cord and all cables.
yy When holding the TV, the screen should face away from you to avoid damage.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part, speaker, or speaker grill area.
yy When transporting the TV, do not expose the TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.
ASSEMBLING AND PREPARING 9
Image shown may differ from your TV.
Only 22/26LT36**
1 |
3 |
|
M4 x 12 |
|
4 EA |
Stand Body |
|
|
Front |
Stand Base
Top View
2
M4 x 16
2 EA
(Only 22LT36**)
M4 x 12 4 EA
ENGLISH
(Only 26LT36**)
ENGLISH
10 ASSEMBLING AND PREPARING
Only 32/37/42/47LT36**
1 |
3 |
M4 x 14 4 EA
Stand Body
Front
Stand Base
Top View
M4 x 14
2 |
4 EA |
|
CAUTION
yyWhen attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.
yyMake sure that the screws are inserted correctly and fastened securely. If they are not fastened securely enough, the TV may tilt forward after being installed. Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly.
NOTE
yyRemove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.