Lenco LED-2411 User Manual

Contents

Introduction

Warning

Caution

Main Unit Description

Remote Control

OSD basic adjustment

DTV Features

USB Features

PVR Opration ( Optional )

Specifications

Trouble Shooting

1

Introduction

Thank you very much for your purchase of

our product of LED TV. It serves as a normal

colour TV and PC monitor. To enjoy your TV to the full from the very beginning, read this manual

carefully and keep it handy for ready reference.

INSTALLATION

ķ Locate the

TV in a room where direct light does not strike the screen. Totaldarkness or a

reflection on the picture screen can cause eyestrain. Soft and indirectlighting is recommended for

comfortable viewing.

ĸAllow enough space between the receiver and the wall to permit ventilation.

Ĺ Avoid excessively warm locations to prevent possible damage to the cabinet orpremature

component failure.

ĺThis TV can be connected to AC100-240V 50/60HZ.

ĻDo not install the TV in a location near heat sources such as radiator, air ducts,direct sunlight,

or in a place somewhere like close compartment and close area. Do notcover the ventilation

openings when using the TV.

ļ The indicator light will last about 30 seconds to go out after cutting off the electricity, during

this period, you cannot repower it on until the indicator light goes out, thanks a lot for your

attention!



2

Warning

This symbol is intended to alert the user to avoid the risk

of electric shock, do not disassemble this equipment by anyone

except a qualified service personnel.

This symbol is intended to alert the user to the presence

of important operation and maintenance instructions in

the literature accompanying the equipment.

CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER- SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

3

4

Caution

High voltages are used in the operation of this product.

- Do not

open the product's casing. Refer servicing

to qualified service personnel .

Caution

To prevent fire or electrical shock hazard, Do not expose

the main unit to moisture.

Caution

Do not drop or push objects into the television cabinet

slots or openings. Never spill any kind of liquid on the

television receiver.

Caution

Avoid exposing the main unit to direct sunlight and other

sources of heat. Do not stand the television receiver

directly on other products which give off heat. E. g. video

cassette players, Audio amplifiers. Do not block the

ventilation holes in the back cover. Ventilation is essential

to prevent failure of electrical component. Do not squash

power supply cord under the main

unit or other heavy objects.

Caution

Never stand on, lean on, push suddenly the product

or its stand. You should Pay special attention to

children.

Caution

Do not place the main unit on an unstable cart stand,

shelf or table. Serious injury to an individual, and

damage to the television, may result if it should fall.

Caution

When the product is not used for an extended period

of time, it is advisable to disconnect the AC power

cord from the AC outlet.

Caution

The LED panel used in this product is made of glass.

Therefore, it can break when the product is dropped

or applied with impact. Be careful not to be injured

by broken glass pieces in case the LED panel breaks.

5

Main unit description

Control Panel Button Function

TV Terminal Connections

1. USB input terminal.

2. HDMI input terminal.

3. VGA input terminal of simulation signal of PC.

4. PC AUDIO terminal.

5. SCART terminal.

6. HEADPHONE output terminal.

7. Component (YPbPr\YCbCr) input terminal .

8. Video input terminal.

9. AUDIO input terminal.

10. .ATV antenna/close circuit TV network port or DTV antenna port.

Power Input Configuration

AC POWER

Optional Configuration as below:

Connect the USB to the USB jack on the set.

VOL+ : Volume up. VOL- : Volume down. CH+ : TV channel up. CH- : TV channel down.

MENU : Press to select the main menu. TV/AV : Select the input signal.

POWER : Switch on when in

standby mode or enter the standby mode.

6

7

NOTE

ƽIt is only 500 mA MAX of DC current output when you connect with USB jack

ƽTo ensure the Mobile HD works well, you should use other power supply for the Mobile HD.

And do not use the USB jack in the same time.

ƽ It supports Mobile HD by connecting with USB jack (must more than 2GB). The partitions of

the Mobile HD can’t be more than 4 partitions. The max partition is 2TB. It supports FAT/FAT32 document. The max FAT document is 4GB and the max FAT32 document is 2TB.