La Crosse Technology WS9123IT Instruction Manual

TEMPERATURE AND HUMIDITY WEATHER STATION

Model WS9123IT Instruction Manual

!!Please read carefully before operating!!

INTRODUCTION:

Congratulations on purchasing this tiny 915MHz Temperature and Humidity Weather
Station which displays the time, indoor temperature, and up to three outdoor temperatures
and humidity readings. With only two easy to use keys, this product is ideal for use in the
home or office.

1

« Instant Transmission+» is the up and coming state-of-the-art new
wireless transmission technology, exclusively designed and developed by
LA CROSSE TECHNOLOGY.
“IT +” offers you an immediate update of all your outdoor data measured
from the transmitters: follow your climatic variations in real-time!

2

FEATURES:
The Temperature Station

LCD

Display

Function

Keys

Hanging
Hole

Battery
compartment
cover

Removable
stand

3

Quartz clock in 12 or 24-hour time display (hour and minute, manually set)

Indoor and outdoor temperature reading in degree Celsius (°C) or Fahrenheit (°F)
Outdoor humidity reading in %RH
Can receive up to three outdoor transmitters
Minimum and Maximum records of indoor temperature, outdoor temperature and

outdoor humidity

Low battery indicator
Table standing or wall mountable

4

The Outdoor Thermo-Hygro Transmitter

Remote transmission of outdoor temperature and hu mi dity to

Temperature Station by 915 MHz signals

Displays alternately the measured temperature and humidity

readings on LCD

Shower proof casing
Wall mounting case. Mounting at a sheltered place. Avoid direct

rain and sunshine.

5

SETTING UP:
When one transmitter is to be used

1. First, insert the batteries to the transmitter (see “How to install and replace
batteries in the Thermo-hygro transmitter” below).

2. Within 2 minutes of powering up the transmitter, insert the batteries to the
Temperature Station (see “How to install and replace batteries in the
Temperature station” below). Once the batteries are in place, all segments of the
LCD will light up briefly. Following the indoor temperature and the time as 12:00 will
be displayed. If they are not shown in LCD after 60 seconds, remove the batteries
and wait for at least 60 seconds before reinserting them. Once the indoor data is
displayed user may proceed to the next step.

3. After the batteries are inserted, the Temperature Station will start receiving data
signal from the transmitter. The outdoor temperature and humidity should then be

6

displayed on the Temperature station. If this does not happen after 2 minutes, the
batteries will need to be removed from both units and reset from step 1.

4. In order to ensure sufficient 915 MHz transmission however, this should under good
conditions be a distance no more than 100 metres between the final position of the
Temperature Station and the transmitter (see notes on “Positioning” and “915 MHz
Reception”).

When more than one transmitter is to be used

1. User shall remove all the batteries from the temperature station and transmitters

and wait 60 seconds if setting has been done with one transmitter before.

2. Insert the batteries to the first transmitter.

3. Within 2 minutes of powering up the first transmitter, insert the batteries to the

Temperature Station. Once the batteries are in place, all segments of the LCD will

7

light up briefly. Following the indoor temperature and the time as 12:00 will be
displayed. If they are not displayed in the LCD after 60 seconds, remove the
batteries and wait for at least 60 seconds before reinserting them.

4. The outdoor temperature and humidity from the first transmitter (channel 1) should

then be displayed on the Temperature station. Also, the signal reception icon will be
displayed. If this does not happen after 2 minutes, the batteries will need to be
removed from both units and reset from step 1.

5. Insert the batteries to the second transmitter as soon as the outdoor temperature

and humidity readings from the first transmitter are displayed on the temperature
station.

Note: User shall insert the batteries into the second transmitter within 30 seconds of
reception of the first transmitter.

8

6. The outdoor temperature and humidity from the second transmitter and the

"channel 2" icon should then be displayed on the Temperature station. If this does
not happen after 2 minutes, the batteries will need to be removed from all the units
and reset from step 1.

7. Insert the batteries to the third transmitter as soon as the "channel 2" icon and

outdoor data are displayed on the temperature station. Then within 2 minutes, the
channel 3 outdoor data from the third transmitter will be displayed and the channel
icon will shift back to "1" once the third transmitter is successfully received. If this
does not happen, user shall restart the setting up from step 1.

Note: User shall insert the batteries into the third transmitter within 30 seconds of
reception of the second transmitter.

9

HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION

The Temperature Station uses 2 x AAA, IEC LR3, 1.5V batteries.
When batteries need to be replaced, the low battery icon will appear
on the LCD. To install and replace the batteries, please follow the
steps below:

1. Lift up the battery compartment cover.

2. Insert batteries observing the correct polarity (see marking).

3. Replace compartment cover.

10