POWER UP
MANUAL TIME SET
14” ULTRATOMIC WALL CLOCK
Model: 404-1235UA-PL | 404-1235UA-SS
DC:032218
1. Slide the Time Zone Switch to your time zone.
PT = Pacific, MT = Mountain, CT = Central, ET = Eastern
2. Select DST (Daylight Saving Time) setting ON/OFF.
When ON is selected, the clock will automatically adjust
for DST (most common).
3. Insert two or four fresh “C”, batteries according to
the polarity markings. Four batteries will extend battery
life.
Important: When batteries are installed, the hands will
move to 4 o’clock, 8 o’clock, or 12 o’clock position and the
clock will start receiving the Atomic Time signal from
Colorado. When signal is received, the hands will move to
the correct time for the selected time zone.
Manual
Time Set
DST
ON
OFF
DST ON/OFF
Set
Q-Mode
Q-Run
Q-Set
Page | 2
SleepPTMTCTET
ECO Mode
ON
OFF
Q-Mode
Time
Zone
Custom
Eco Mode
ON/OFF
1. Set DST switch to the OFF (Q-Set) and Time Zone switch to
the Q-MODE. The movement will move to 4, 8 or 12 o’clock
position and stop.
2. Press and release the SET button to change the time slowly.
Hold the SET button to set the time quickly.
3. When time is set, slide the DST switch to ON (Q-RUN)
position. The second hand will start running from 12:00 and
the clock will keep time as manually set.
FEATURES
Custom Time Zone Setting:
Select time zones from +0 UTC to -11 UTC.
1. Slide Time Zone Switch to CUSTOM ET.
2. Press and release Manual Time Set button to advance time
in one hour increments until you reach desired time.
Eco-Mode:
· Eco-mode is a battery saving feature.
· When ON is selected: between the hours of 11pm-5am, the
second hand will stop at 12:00. The second hand will resume
running at 5am.
· When OFF is selected: the second hand runs normally.
Low Battery Indication:
When the batteries are low the second hand will stop at 6:00
and the hour and minutes hands will run as usual.
Page | 3
ULTRATOMIC TIME RECEPTION
Using the NIST’s newly enhanced phase-modulation based
broadcast system, this clock is the first of its kind to take
advantage of this technology. Due to the dual-antenna
scheme used with this type of broadcast, this clock will offer
significantly better signal reception no matter the orientation
of installation.
For information about WWVB visit: http://bit.ly/AtomicTime
WE’RE HERE TO HELP!
FIND FULL MANUALS, FAQS, AND MORE UNDER THE
SUPPORT TAB HERE: http://bit.ly/404-1235UA
JOIN THE CONVERSATION
Ask questions, watch detailed setup videos, and provide feedback
on our social media outlets!
SPECIFICATIONS
Power Requirements: 2 or 4 “C” LR14, IEC 1.5V batteries
Battery Life in Eco Mode: 2 “C” batteries up to 3 years
4 “C” batteries up to 6 years
With reputable batteries
WARRANTY INFO
NEED MORE HELP?
Our knowledgeable customer support team is available:
Monday-Friday, 8am-6pm CST. Phone: 1.608.782.1610
La Crosse Technology, Ltd. provides a 1-year limited time
warranty (from date of purchase) on this product relating to
manufacturing defects in materials & workmanship.
For Full Warranty Details, Visit:
www.lacrossetechnology.com/support
CARE + MAINTENANCE
· Do not mix old and new batteries.
· Do not mix Alkaline, Lithium, standard, or rechargeable
batteries.
· Always purchase the correct size and grade of battery most
suitable for intended use.
· Clean the battery contacts and also those of the device prior to
battery installation.
· Ensure the batteries have with correct polarity (+ / -).
· Remove batteries from equipment that will not to be used for an
extended period.
· Promptly remove expired batteries.
CANADA STATEMENT
This device complies with CNR Industry Canada license -exempt
devices. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Page | 5 Page | 6Page | 4
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Increase separation between equipment & receiver.
• Consult the dealer or an experienced radio/TV technician for help.
This device must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions:
(1 ) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized changes or modifications to this equipment. Such changes or
modifications could void the user authority to operate the equipment.
All rights reserved. This manual may not be reproduced in any form, even in part, or
duplicated or processed using electronic, mechanical or chemical process without
the written permission of the publisher.
This booklet may contain errors or misprints. The information it contains is regularly
checked and corrections are included in subsequent editions. We disclaim any
responsibility for any technical error or printing error, or their consequences. All
trademarks and patents are recognized.
Loading...