How it Works
Kyocera
Loading...
FS-C8520

Kyocera FS-C8520, FS-8525MFP SERVICEBULLETINS Ver.1.03E

C189_SystemError(Fxxx)Outline_Ver.1.03E 1/8
No.
Content
Check procedure & check point
Remark 1
TASKalfa 306i/FS-6530MFP, TASKalfa 256i/FS-6525MFP
-
Lock-up at Welcome display (TASKalfa/Ecosys) (The display unchages after a certain time (Note 1: *** seconds))
1) Check connection of the harness (Panel to Main board), (Main board to HDD) and connectors and check function.
2) Check contact of the DDR memory by detaching and reattaching. and check function. replace it if available and check function.
3) Format the HDD and check function. (U024 FULL formatting) (*1)
4) Execute the U021Memory initializing to initialize the controller backup memory and check function.
5) Replace the panelmain board and check function.
6) Replace the main board and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
*User data and installed software is deleted if executing the U024. Reinstallation is required.
[Main - Panel Interface] Main board: YC100, YC101, YC102 Panel board: YC1, YC2, YC3
(Note 1) 70 seconds [Check the contact with the DDR2 memory]
Main board: YS1 A certain part of the memory may be faulty. The frequency of faiure occurrence is dependent on the frequency of access to the faulty bit. The memories except the DIMM are mounted on the main PWB. The mounted memories or the ASIC may be faulty if the DIMM is not sensitive.
F000
CF000 appears in a certain time (Note 2: *** seconds) after the Welcome display continues
Panel－Main board communication error
1) Check connection of the harness (Panel to Main board), (Main board to HDD) and connectors and check function.
2) Check contact of the DDR memory by detaching and reattaching. and check function. replace it if available and check function.
3) Format the HDD and check function. (U024 FULL formatting) (*1)
4) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
5) Replace the main board and check function.
6) Replace the panelmain board and check function.
7) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
[Main-Panel Interface] Main board: YC100, YC101, YC102 Panel board: YC1, YC2, YC3
If the LEDs are in the state below when the F000 appears, the DDR2 memory failure may be the cause. Check contact of the YS1 with the memory. (DDR2 memory is the option item for the monochrome models, and is the standard item for the color models.) Memory LED turned on Attention LED turned on (Note 1) 70 seconds
[Check the contact with the DDR2 memory] Main board: YS1 A certain part of the memory may be faulty. The frequency of faiure occurrence is dependent on the frequency of access to the faulty bit. The memories except the DIMM are mounted on the main PWB. The mounted memories or the ASIC may be faulty if the DIMM is not sensitive.
F10X
F11X
F12X
An error is detected at the Scan control section
1) Check connection of the harness (Scan/DP - Main board) and connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
4) Replace the Scan/DP board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
[Main-Scan Interface] Main board:YC112 ,YC113 CCD board: YC1 LED board: YC1
An error is detected at OS or some of device drivers.
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
C189_SystemError(Fxxx)Outline_Ver.1.03E 2/8
No.
Content
Check procedure & check point
Remark 1
TASKalfa 306i/FS-6530MFP, TASKalfa 256i/FS-6525MFP
F13X
An error is detected at the Panel control section
1) Check connection of the harness (Panel - Main board) and connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
4) Replace the panel board and check function. (*2)
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only. (*2) For the model separating the main/panel PWBs.
[Main-Panel Interface] Main board: YC100, YC101, YC102 Panel board: YC1, YC2, YC3
F14X
An error is detected at the FAX control section
1) Check connection of the harness (FAX - Main board) and connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
4) Execute the U671 Clear FAX back up data (FAX DIMM clear) and check function. (*3) (Take cae of the received data since it is cleared)
5) Replace the FAX_DIMM and check function.
6) Replace the FAX board and check function.
7) Replace the main board and check function.
8) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only. (*3) For the models using the main PWB with the flash for the FAX data.
F14A,F14F: KUIO error Main board (USB hub)
[Main-KUIO Interface] Main board: YC109 (Reference) YC16 is at the side where the IB-50 is inserted. <Note>
4) is not supported.
5) is unnecessary.
F15X
An error is detected at the authentication device control section
1) Check connection of the harness (Authentication device - Main board) and connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
4) Replace the main board and check function.
5) Replace the HDD and check function. (*1)
6) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
Authentication device: Card Reader, etc.
[Main-USB Host Interface] Main board: YC107(USB Host where is at the side of the oparation unit) YC108(USB Host where is at the back side of the main frame)
F16X
An error is detected at the KMAS control section
1) Check connection of the harness (KMAS - Main board) and connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function.　(*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
-
F17X
An error is detected at the print data control section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
C189_SystemError(Fxxx)Outline_Ver.1.03E 3/8
No.
Content
Check procedure & check point
Remark 1
TASKalfa 306i/FS-6530MFP, TASKalfa 256i/FS-6525MFP
F18X
An error is detected at the Video control secion
1) Check connection of the harness (Engine - Main board) and connectors and check function.
2) Format the HDD and check function. (U024 FULL formatting) (*1)
3) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
4) Replace the engine board and check function.
5) Replace the main board and check function.
6) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
<Monochrome models> [Main-LSU Interface] Main board: YC103 LSU(APC PWB): YC2 [Main-Engine Interface] Main board: YC105 Engine board: YC17
<Color models> [Main-LSU Interface] Main board: YC104 LSU relay board: YC10 [Main-Engine Interface] Main board: YC105 Engine board: YC26 [Relay connector] Between the main board and the LSU relay board.
F19X
F1AX
F1BX
An error is detected at the Security management section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
F1CX
An error is detected at the File System management section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
*The F1C4 error appears with the HDD security kit at work.
F1DX
An error is detected at the Image memory management section
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
*The F1D4 error is RAM allocation error.
　1. Check it with the U340
　2. Initialize the setting
valued with the U021
F1EX
F1FX
F20X
An error is detected at the OS or some of device drivers
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
An error is detected at the OS or some of device drivers
1) Format the HDD and check function. (U024 FULL formatting) (*1)
2) Execute the U021 Memory initializing to initialize the controller backup memory and check function.
3) Replace the main board and check function.
4) Replace the HDD and check function. (*1)
5) Retrieve the USBLOG and contact the Service Administrative Division. (*1) For the HDD standard model only.
Loading...
+ 5 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use