FS-1920
Table of contents
Loading...
FS-1920
Page Printer
Operation Guide
Caution on Installation
No liability is assumed for any damage caused by improper installation.
Notice on Software
Software used with this printer must support the printer’s emulation mode. The printer is factory-set to emulate the PCL. The emulation mode can be changed by following the procedures described in Chapter 1.
Notice on This Guide
The information in this guide is subject to change without notification. Additional pages may be inserted in future editions. The user
is asked to excuse any technical inaccuracies or typographical errors in the present edition.
No responsibility is assumed if accidents occur while the user is following the instructions in this guide. No responsibility is assumed
for defects in the printer’s firmware (contents of its read-only memory).
This guide, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by
copyright. All rights are reserved. Copying or other reproduction of all or part of this guide, any copyrightable subject matter without
the prior written consent of Kyocera Corporation is prohibited. Any copies made of all or part of this guide, any copyrightable subject
must contain the same copyright notice as the material from which the copying is done.
Regarding Tradenames
PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL and KIR (Kyocera Image Refinement) are trademarks of
Kyocera Corporation.
Diablo 630 is a product of Xerox Corporation. IBM Proprinter X24E is a product of International Business Machines Corporation. Epson
LQ-850 is a product of Seiko Epson Corporation.
Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-Packard Company. Centronics is a trade name of Centronics
D a ta C o m p u te r I n c . Po s t S cr i p t i s a r e g i s tered trademark of Adobe Systems Incorporated. Macintosh is a registered trademark of Apple
computer, Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. PowerPC and Microdrive
are trademarks of International Business Machines Corporation. CompactFlash is a trademark of SanDisk Corporation. E
S
TAR is a U.S. registered mark. All other brand and product names are registered trademarks or trademarks of their respective
companies.
This Kyocera Mita page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6 language emulation. PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A.
This product was developed using the Tornado™ Real Time Operating System and Tools from Wind River Systems.
This product contains UFST
™
and MicroType® from Agfa Monotype Corporation.
NERGY
©2003, 2004 by KYOCERA MITA CORPORATION All rights reserved.
Revision 1.1 January 2004
i
IBM PROGRAM LICENSE AGREEMENT
The device you have purchased contains one or more software programs ("Programs") which belong to international business machines
corporation ("IBM"). This document defines the terms and conditions under which the software is being licensed to you by IBM. If you
do not agree with the terms and conditions of this license, then within 14 days after your acquisition of the device you may return the
device for a full refund. If you do not so return the device within the 14 days, then you will be assumed to have agreed to these terms
and conditions.
The Programs are licensed not sold. IBM, or the applicable IBM country organization, grants you a license for the Programs only in the
country where you acquired the Programs. You obtain no rights other than those granted you under this license.
The term "Programs" means the original and all whole or partial copies of it, including modified copies or portions merged into other
programs. IBM retains title to the Programs. IBM owns, or has licensed from the owner, copyrights in the Programs.
1. License
Under this license, you may use the Programs only with the device on which they are installed and transfer possession of the Programs
and the device to another party.
If you transfer the Programs, you must transfer a copy of this license and any other documentation to the other party. Your license is
then terminated. The other party agrees to these terms and conditions by its first use of the Program.
You may not:
1) use, copy, modify, merge, or transfer copies of the Program except as provided in this license;
2) reverse assemble or reverse compile the Program; or
3) sublicense, rent, lease, or assign the Program.
2. Limited Warranty
The Programs are provided "AS IS."
There are no other warranties covering the Programs (or conditions), express or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose.
Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.
3. Limitation of Remedies
IBM’s entire liability under this license is the following;
1) For any claim (including fundamental breach), in any form, related in any way to this license, IBM’s liability will be for actual
damages only and will be limited to the greater of:
a) the equivalent of U.S.$25,000 in your local currency; or
b) IBM’s then generally available license fee for the Program
This limitation will not apply to claims for bodily injury or damages to real or tangible personal property for which IBM is legally liable.
IBM will not be liable for any lost profits, lost savings, or any incidental damages or other economic consequential damages, even if
IBM, or its authorized supplier, has been advised of the possibility of such damages. IBM will not be liable for any damages claimed by
you based on any third party claim. This limitation of remedies also applies to any developer of Programs supplied to IBM. IBM’s and
the developer’s limitations of remedies are not cumulative. Such developer is an intended beneficiary of this Section. Some jurisdictions
do not allow these limitations or exclusions, so they may not apply to you.
4. General
You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this
license. In either event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including
personal property taxes, resulting from this license. Neither party may bring an action, regardless of form, more than two years after
the cause of action arose. If you acquired the Program in the United States, this license is governed by the laws of the State of New York.
If you acquired the Program in Canada, this license is governed by the laws of the Province of Ontario. Otherwise, this license is
governed by the laws of the country in which you acquired the Program.
ii
Typeface Trademark Acknowledgement
All resident fonts in this printer are licensed from Agfa Corporation.
Helvetica, Palatino and Times are registered trademarks of Linotype-Hell AG.
ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC Zapf Dingbats are registered trademarks of International Typeface Corporation.
Agfa Japan License Agreement
1. “Software” shall mean the digitally encoded, machine readable, scalable outline data as encoded in a special format as well as the
UFST Software.
2. You agree to accept a non-exclusive license to use the Software to reproduce and display weights, styles and versions of letters,
numerals, characters and symbols (“Typefaces”) solely for your own customary business or personal purposes at the address stated
on the registration card you return to Agfa Japan. Under the terms of this License Agreement, you have the right to use the Fonts
on up to three printers. If you need to have access to the fonts on more than three printers, you need to acquire a multi-user license
agreement which can be obtained from Agfa Japan. Agfa Japan retains all rights, title and interest to the Software and Typefaces
and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement.
3. To protect proprietary rights of Agfa Japan, you agree to maintain the Software and other proprietary information concerning the
Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces.
4. You agree not to duplicate or copy the Software or Typefaces, except that you may make one backup copy. You agree that any such
copy shall contain the same proprietary notices as those appearing on the original.
5. This License shall continue until the last use of the Software and Typefaces, unless sooner terminated. This License may be
terminated by Agfa Japan if you fail to comply with the terms of this License and such failure is not remedied within thirty (30)
days after notice from Agfa Japan. When this License expires or is terminated, you shall either return to Agfa Japan or destroy all
copies of the Software and Typefaces and documentation as requested.
6. You agree that you will not modify, alter, disassemble, decrypt, reverse engineer or decompile the Software.
7. Agfa Japan warrants that for ninety (90) days after delivery, the Software will perform in accordance with Agfa Japan-published
specifications, and the diskette will be free from defects in material and workmanship. Agfa Japan does not warrant that the
Software is free from all bugs, errors and omissions.
The parties agree that all other warranties, expressed or implied, including warranties of fitness for a particular purpose and
merchantability, are excluded.
8. Your exclusive remedy and the sole liability of Agfa Japan in connection with the Software and Typefaces is repair or replacement
of defective parts, upon their return to Agfa Japan.
In no event will Agfa Japan be liable for lost profits, lost data, or any other incidental or consequential damages, or any damages
caused by abuse or misapplication of the Software and Typefaces.
9. New York, U.S.A. law governs this Agreement.
10. You shall not sublicense, sell, lease, or otherwise transfer the Software and/or Typefaces without the prior written consent of Agfa
Japan.
11. Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer
Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate. Further use, duplication or
disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c)(2).
12. You acknowledge that you have read this Agreement, understand it, and agree to be bound by its terms and conditions. Neither
party shall be bound by any statement or representation not contained in this Agreement. No change in this Agreement is effective
unless written and signed by properly authorized representatives of each party. By opening this diskette package, you agree to
accept the terms and conditions of this Agreement.
Cautions for Toner Handling
• Do not incinerate toner and toner containers. Dangerous sparks may cause burn.
• Never open the toner container or waste toner box.
• Make sure not to inhale the toner, and not to rub your eyes or touch your mouth with the hands stained with the toner. And make
sure not to stick to your skin.
• For the disposal of old toner container and waste toner box, consult your dealer. Or dispose of the toner or toner containers in
accordance with Federal, state and Local rules and regulations.
• Keep away the toner container and the waste toner box from children.
iii
Contents
Contents
Introduction ................................................................................................ ix
Features ........................................................................................................................................................... x
For More Information................................................................................................................................... xiii
Guide to the Operation Guide...................................................................................................................... xiv
Chapter 1
Understanding the Operator Panel ............................................................................................................. 1-2
Message Display .................................................................................................................................... 1-2
Interface Indicator ................................................................................................................................. 1-3
Paper Size Indicator............................................................................................................................... 1-3
Paper Type Indicator ............................................................................................................................. 1-4
READY, DATA, and ATTENTION Indicators ...................................................................................... 1-4
Keys ........................................................................................................................................................ 1-5
Menu System Road Map........................................................................................................................ 1-6
Printing Test Pages .................................................................................................................................... 1-12
Menu Map ............................................................................................................................................ 1-12
Status Page........................................................................................................................................... 1-14
Service Status Page ............................................................................................................................. 1-18
Network Card Interface Status Page.................................................................................................. 1-19
Font Lists.............................................................................................................................................. 1-21
Received Data Dumping ...................................................................................................................... 1-23
Paper Handling........................................................................................................................................... 1-24
Setting the Paper Size ......................................................................................................................... 1-24
Setting the Paper Type........................................................................................................................ 1-30
MP Tray Mode...................................................................................................................................... 1-37
Selecting the Paper Feed Source ......................................................................................................... 1-38
Selecting the Output Stack ................................................................................................................. 1-39
Overriding A4 and Letter Size Difference .......................................................................................... 1-40
Using the Operator Panel ....................................................... 1-1
Setting the Paper Size in Paper Cassette ............................................................................ 1-24
Setting the Paper Size in MP Tray ....................................................................................... 1-28
Setting the Paper Type in Paper Cassette ........................................................................... 1-30
Setting the Paper Type in MP Tray ..................................................................................... 1-31
Creating Custom Paper Type ............................................................................................... 1-32
Resetting the Custom Paper Type ........................................................................................ 1-36
iv
Contents
Pagination ................................................................................................................................................... 1-41
Emulation............................................................................................................................................. 1-41
Changing the Emulation ...................................................................................................... 1-41
Alternative Emulation for KPDL Emulation ...................................................................... 1-42
Printing KPDL Errors .......................................................................................................... 1-43
Font....................................................................................................................................................... 1-44
Default font ............................................................................................................................ 1-44
Default Font Size ................................................................................................................... 1-46
Changing Type for Courier/Letter Gothic ............................................................................ 1-47
Setting the Character Pitch for Courier/Letter Gothic ....................................................... 1-48
Code Set................................................................................................................................................ 1-49
Number of Copies................................................................................................................................. 1-50
Printing Orientation ............................................................................................................................ 1-51
KIR (Kyocera Image Refinement) ....................................................................................................... 1-52
Ecoprint ................................................................................................................................................ 1-54
Resolution............................................................................................................................................. 1-55
e-MPS .......................................................................................................................................................... 1-56
Quick Copy ........................................................................................................................................... 1-57
Proof and Hold ..................................................................................................................................... 1-59
Printing a Private Job ......................................................................................................................... 1-61
Printing a Stored Job........................................................................................................................... 1-63
Printing a Code Job ............................................................................................................................. 1-65
Printing a List of Code Jobs ................................................................................................................ 1-67
Retrieving Jobs from Virtual Mailbox (VMB) .................................................................................... 1-68
Printing a List of VMB ........................................................................................................................ 1-69
e-MPS Configuration ........................................................................................................................... 1-70
Interface ...................................................................................................................................................... 1-74
Parallel Interface Mode ....................................................................................................................... 1-74
USB Interface Mode............................................................................................................................. 1-75
Serial Interface Parameters ................................................................................................................ 1-76
Network Interface Parameters............................................................................................................ 1-78
Operating the Storage Device .................................................................................................................... 1-81
Activating the RAM Disk .................................................................................................................... 1-81
Reading Data ....................................................................................................................................... 1-83
Writing Data......................................................................................................................................... 1-84
Deleting Data ....................................................................................................................................... 1-86
Reading Fonts from a CompactFlash Card ........................................................................................ 1-87
Formatting a Storage Device............................................................................................................... 1-88
Printing a List of Data Names ............................................................................................................ 1-89
v
Contents
Configuration.............................................................................................................................................. 1-91
Page Protect Mode ............................................................................................................................... 1-91
Linefeed (LF) Action ............................................................................................................................ 1-92
Carriage-Return (CR) Action .............................................................................................................. 1-93
Wide A4 Pitch....................................................................................................................................... 1-94
Print Density........................................................................................................................................ 1-95
Total Printed Pages.............................................................................................................................. 1-96
Toner Counter Resetting ..................................................................................................................... 1-96
Message Language............................................................................................................................... 1-97
Automatic Form Feed Timeout............................................................................................................ 1-99
Sleep Timer Setting ........................................................................................................................... 1-100
Printer Resetting ............................................................................................................................... 1-102
Resource Protection ........................................................................................................................... 1-103
Alarm (Buzzer) Setting...................................................................................................................... 1-104
Auto Continue Setting ....................................................................................................................... 1-105
Duplex Printing Error Detection Setting .........................................................................................1-107
Chapter 2
General Guidelines....................................................................................................................................... 2-2
Paper Availability .................................................................................................................................. 2-2
Paper Specifications............................................................................................................................... 2-2
Selecting the Right Paper...................................................................................................................... 2-3
Special Paper ................................................................................................................................................ 2-7
Transparency (Overhead Projection Film) ........................................................................................... 2-7
Adhesive-Backed Labels ........................................................................................................................ 2-8
Paper Type .................................................................................................................................................. 2-12
Chapter 3
Toner Container Replacement ..................................................................................................................... 3-2
Toner Container Replacement Interval................................................................................................ 3-2
Replenishing Toner................................................................................................................................ 3-3
Waste Toner Box Replacement .................................................................................................................... 3-6
Replacing the Waste Toner Box............................................................................................................. 3-6
Cleaning ........................................................................................................................................................ 3-9
Cleaning the Charger Wire ................................................................................................................... 3-9
Cleaning the Charger Grid.................................................................................................................. 3-10
Paper Transfer Unit............................................................................................................................. 3-13
Paper Selection....................................................................... 2-1
Maintenance ........................................................................... 3-1
vi
Contents
Chapter 4
General Guide............................................................................................................................................... 4-2
Print Quality Problems ................................................................................................................................ 4-3
Indicators and Messages .............................................................................................................................. 4-6
Indicators................................................................................................................................................ 4-6
Maintenance Messages.......................................................................................................................... 4-7
Error Messages .................................................................................................................................... 4-10
Correcting a Paper Jam.............................................................................................................................. 4-12
Jam at the Paper Cassette or Inside the Printer ............................................................................... 4-14
Paper Jam at the Option Duplexer ..................................................................................................... 4-16
Paper Jam at the Option Sorter.......................................................................................................... 4-18
Jam at the MP Tray............................................................................................................................. 4-20
Chapter 5
List of Fonts .................................................................................................................................................. 5-2
PCL (Scalable and Bitmap) Fonts......................................................................................................... 5-2
KPDL Fonts (1) ...................................................................................................................................... 5-5
KPDL Fonts (2) ...................................................................................................................................... 5-6
Troubleshooting ...................................................................... 4-1
Fonts ....................................................................................... 5-1
Appendix A
Available Options .........................................................................................................................................A-2
Expanding the Printer Memory...................................................................................................................A-3
Installing Option Units ................................................................................................................................A-9
PF-60 Paper Feeder................................................................................................................................A-9
DU-61 Duplexer ...................................................................................................................................A-12
SO-60 Sorter.........................................................................................................................................A-15
EF-60 Envelope Feeder........................................................................................................................A-21
PT-4/PT-60 Rear Tray .........................................................................................................................A-25
Network Interface Card.......................................................................................................................A-26
Microdrive (Hard Disk)........................................................................................................................A-28
CompactFlash (Memory) Card ............................................................................................................A-30
Appendix B
Parallel Interface......................................................................................................................................... B-2
Parallel Interface Communication Modes ........................................................................................... B-2
Interface Signals ................................................................................................................................... B-2
USB Interface .............................................................................................................................................. B-5
Specifications ........................................................................................................................................ B-5
Interface Signals ................................................................................................................................... B-5
Options .................................................................................... A-1
Host Computer Interface........................................................ B-1
vii
Contents
Serial Interface (Option) ............................................................................................................................. B-6
RS-232C Interface................................................................................................................................. B-6
RS-232C Protocol ......................................................................................................................................... B-7
PRESCRIBE FRPO D0 Command.......................................................................................................B-9
RS-232C Cable Connection ....................................................................................................................... B-10
Obtain a Suitable RS-232C Cable...................................................................................................... B-10
Connecting the Printer to the Computer........................................................................................... B-10
Appendix C
Specifications ......................................................................... C-1
Glossary .......................................................................................Glossary-1
Index ................................................................................................. Index-1
viii
Introduction
The Kyocera Mita page printer has many extremely desirable features. It was designed to
make a contribution to a cleaner environment as well as to represent the latest generation of
page printer technology.
This section contains the following subsections.
•Features
• For More Information...
• Guide to the Operation Guide
ix
Features
This section outlines the common major printer features of the FS-1920
page printer.
Ultra long life modules
The drum, developer, and fuser have been designed for ultra long life.
Amorphous silicon drum
The drum has been developed using Kyocera’s unique ceramic technology
using amorphous silicon.
KIR (Kyocera Image Refinement)
This is Kyocera’s original smoothing function. It uses software to enhance
the printer’s resolution and produce high-quality printing. The default
setting is On.
Superb print quality
Using 1200 dpi resolution in Fast 1200 mode, the printout is close to
typeset quality. Also, with Kyocera Image Refinement (KIR) technology,
high quality printing can be achieved even at 300 dpi and 600 dpi.
Large paper capacity
Approximately 500 sheets can be loaded into the paper cassette, and about
100 sheets can be loaded into the MP tray.
Wide variety of print media
As well as standard paper, the printer will print on transparency, labels
and other types of special purpose media.
Sleep Mode
Conserves energy during the printer’s idle periods.
Ecoprint
Extends the toner yield by reducing the amount of toner used on the page.
Displaying printer messages in any of eight languages
Printer messages can be displayed in English, French, German, Italian,
Dutch, Spanish, or Portuguese.
x
USB (Universal Serial Bus) Interface
This printer supports Full-Speed USB 2.0 standards. Connection to a
computer with a USB interface gives a higher communication speed than
parallel interface connection.
e-MPS
‘e-MPS’ is an abbreviation for ‘enhanced-Multiple Printing System,’ which
is a post-processing function that combines electronic sorting, job
retention, and virtual mailboxing.
When printing multiple copies of a document, the data is transferred from
the computer to the printer only for the first copy; the data is then stored
on the printer’s hard disk. Copies of the document are printed using the
stored data.
Printing is performed faster with less computer spooling time and less
network traffic.
Furthermore, printed data that is stored on the hard disk can be called up
using job retention functions, such as Quick Copy etc., allowing you to
quickly print additional copies of a document from the printer at any time,
without needing to re-spool the document or start up the computer system.
Printer control language PRESCRIBE
The printer uses PRESCRIBE, Kyocera Mita’s page printer control
language with enhanced color graphics capabilities. The simple commands
of PRESCRIBE allow the programmers to easily define pagination and
device control.
KPDL3 (Kyocera Printer Description Language 3)
KPDL3 is the Kyocera’s implementation of the PostScript page description
language Level 3. The printer has 80 fonts that are compatible with Adobe
PostScript fonts. (The printer also has 80 PCL fonts.)
PDF direct printing
Allows you to send a selected PDF file directly to the printer without
invoking a printer driver.
Account management system
The account management system function records the number of pages
printed by each department. The administrator can preset the maximum
number of pages that each department will be allowed to print.
xi
Microdrive (hard disk unit) slot for various functions such as job
retention, VMB, and more
By saving print jobs onto the Microdrive, they can be printed out at the
operator panel when desired. The electronic sort function can be used for
much faster printing.
CompactFlash card slot for option fonts, macros, forms, etc.
Data in the CompactFlash card can be selectively read from the printer’s
operator panel.
SNMP compliance
The printer complies with Simple Network Management Protocol (SNMP).
The SNMP is used for providing and transferring management information
(MIB) between the printer and the host computer.
Support for network printer monitor utility (KM-NET VIEWER)
Allows network wide management of printers. See the readme file in the
CD-ROM (comes with the printer) for details.
xii
For More Information...
Item Description
Installation Guide
(paper manual)
KX Printer Driver
Installation Guide
(paper manual)
Operation Guide
(this manual)
KX Printer Drivers
Operation Guide
PRESCRIBE Command
Technical Reference
PRESCRIBE Command
Reference
Describes procedures from printer setup to printing
a test page.
Describes the procedure to install the printer driver
software.
Guides you through topics concerning the
operations and maintenance of the printer.
Describes how to install and set the printer driver.
PRESCRIBE is the native language of the Kyocera
Mita printers. This Technical Reference contains
the information about how the printing is
performed using the PRESCRIBE commands as
well as the font and emulation description. Also
included is a list of permanent parameters and
their explanation needed when customizing your
printer.
Gives a detailed explanation of the PRESCRIBE
command syntax and parameters with the aid of
print examples.
Note
• For information on how to install the printer driver software, refer to
the KX Printer Driver Installation Guide that is included with the
printer.
• For information on how to use the printer driver software, refer to the
KX Printer Driver Operation Guide that is included on the CD-ROM
(comes with the printer).
xiii
Guide to the Operation Guide
This Operation Guide has the following chapters:
Chapter 1 Using the Operator Panel
This chapter explains the message display, indicators and keys on the
operator panel, and how to make various settings from the operator panel.
Chapter 2 Paper Selection
This chapter explains the types of paper that can be used with the printer.
Chapter 3 Maintenance
This chapter explains how to replace the toner container, waste toner box,
and how to care for your printer.
Chapter 4 Troubleshooting
This chapter explains how to handle printer problems that may occur, such
as paper jams.
Chapter 5 Fonts
This chapter explains about fonts and lists the printer’s internal fonts.
Appendix A Options
This appendix explains how to expand the printer's memory and how to
install each option unit.
Appendix B Host Computer Interface
This appendix explains the pin assignment and specifications for the
printer’s parallel interface, USB interface, and option serial interface.
Appendix C Specifications
This appendix lists the printer’s specifications.
Glossary
This glossary explains the terminology used in this guide.
The following symbols are used to attract your attention in this guide. The
symbols and their meanings are as follows:
xiv
Note
Caution
Warning
Option
Indicates tips or advice useful for operation.
Indicates situations that are potentially hazardous to the human body or
devices.
Indicates situations that are potentially extremely hazardous to the
human body or devices.
Indicates operations that can be performed or are effective only when the
required option unit is installed.
xv
Chapter 1
Using the Operator
Panel
1
This chapter explains the following topics:
• Understanding the Operator Panel
• Printing Test Pages
• Paper Handling
• Pagination
•e-MPS
•Interface
• Operating the Storage Device
• Configuration
1-1
Understanding the Operator Panel
Understanding the Operator Panel
The operator panel has a LCD message display, three indicators, and eight
keys.
Messages that appear on the display and functions of indicators and keys
are explained in the sections that follows.
Message Display
The message display gives information in the form of short messages. The
eight messages listed below are displayed during normal warm-up and
printing.
Other messages that may appear when the printer needs the operator’s
attention are explained in Chapter 4.
Message Meaning
Self test
Please wait
Ready
Processing
Sleeping
Cancelling data
Waiting
FormFeed Time Out
The printer is self-testing after power-up.
The printer is warming up and is not ready. When
the printer is switched on for the first time after the
toner container is installed,
also appears.
The printer is ready to print.
The printer is receiving data, generating graphics,
reading a CompactFlash card/Microdrive, or
printing.
The printer is in sleep mode. The printer wakes
from sleep mode whenever the
operator panel is pressed, the cover is opened or
closed, or data is received. The printer then warms
up and goes online. The time that the printer takes
to enter sleep mode depends on the sleep timer
setting.
Jobs inside the printer are being canceled. To cancel
a job, see the table on page 1-5.
The printer is waiting for the end-of-job command
before printing the last page. Pressing the GO key
allows you to obtain the last page immediately.
The printer is printing the last page after a waiting
period.
(Adding toner)
GO key on the
Table 1-1
1-2
Interface Indicator
Note
Paper Size Indicator
Understanding the Operator Panel
INTERFACE
The interface indicator shows the interface that is currently used. It uses
the following abbreviations:
PAR Standard bi-directional parallel interface
USB Standard USB interface
SER Option serial interface (RS-232C)
OPT Option network interface card
--- No interface is active.
Each interface has a timeout time of 30 seconds during which the other
interface should wait to receive a print job. Even a print job has been
complete on the interface, you should wait for this period until the other
interface begins printing the job.
SIZE
This indicator indicates the paper size of the current paper cassette. The
following abbreviations are used to indicate the paper sizes.
Message
Display
Paper Size Message
Display
Paper Size
A4 ISO A4 (21 × 29.7 cm) EX Executive (7-1/4 × 10-1/2 inches)
A5 ISO A5 (14.8 × 21 cm) #6 Commercial 6-3/4
(3-5/8 × 6-1/2 inches)
A6 ISO A6
(10.5 × 14.8 cm)
†
#9 Commercial 9
(3-7/8 × 8-7/8 inches)
†
†
B5 JIS B5 (18.2 × 25.6 cm) O2 Oficio II (8-1/2 × 13 inches)
B6 JIS B6
(12.8 × 18.2 cm)
LT Letter
†
16K 16 kai (19.7 × 27.3 cm)
ST Statement (5-1/2 × 8-1/2 inches)
(8-1/2 × 11 inches)
LG Legal
FO Folio (21 × 33 cm)
(8-1/2 × 14 inches)
MO Monarch
(3-7/8 × 7-1/2 inches)
BU Business
(4-1/8 × 9-1/2 inches)
DL ISO DL (11 × 22 cm)†Y2 Envelope (Youkei 2)
C5 ISO C5
(16.2 × 22.9 cm)
HA Japanese Postcard (10 × 14.8 cm)
†
OH Return Postcard (20 × 14.8 cm)
†
(11.4 × 16.2 cm)
Y4 Envelope (Youkei 4)
(10.5 × 23.5 cm)
†
†
b5 ISO B5 (17.6 × 25 cm) CU Custom Size
(14.8 × 21 cm to 21.6 × 35.6 cm)
†
†
†
Note
Table 1-2
† With only the MP tray feeding.
While the printer is processing data, the SIZE indicator indicates the
paper size selected by the application software.
1-3
Understanding the Operator Panel
Paper Type Indicator
This shows the paper type defined for the current paper casette. Automatic
cassette switching is available according to the paper type.
The paper type can be specified at the operator panel. See Creating
Custom Paper Type on page 1-32.
The following abbreviations are used to indicate the paper type.
Message Display Paper Type Message Display Paper Type
None Auto LETTERHEA Letterhead
PLAIN Plain COLOR Color
TRNSPRNCY Transparency
PREPRINTE Preprinted ENVELOPE Envelope
LABELS Labels
BOND Bond THICK Thick
RECYCLED Recycled HIGH QUAL High quality
VELLUM Vellum
ROUGH Rough
TYPE
†
PREPUNCHE Prepunched
†
†
†
CARDSTOCK Cardstock
CUSTOM 1 (to 8) Custom 1 (to 8)
†
†
Table 1-3
† With only the MP tray feeding.
READY, DATA, and ATTENTION Indicators
The following indicators light during
normal operation and when the
printer needs attention.
Indicator Description
READY
ATTENTION
Flashing: Indicates when an error occurs that you can clear
by yourself.
Lit: Indicates that the printer is on-line.
The printer prints received data.
Off: Indicates that the printer is off-line. Data can be received
but will not be printed. Also indicates when printing is
automatically stopped due to occurrence of an error.
Flashing: Indicates data transfer is taking place.
DATA
Lit: Indicates either that data is being processed, or that data
is being written to the memory card.
Flashing: Indicates when the printer needs maintenance
attention or the printer is warming up (
Lit: Indicates when a problem or an error occurs that you can
clear by yourself.
(For example, paper jam occurs.)
Ready
PAR A4 PLAIN
INTERFACE SIZE TYPE
READY
DATA
ATTENTION
Please wait).
Table 1-4
1-4
Keys
Note
Key Function
• Switches the printer on-line and off-line.
GO
CANCEL
†
MENU
• Prints and feed out one page.
• Cancels specific errors.
• Cancels a printing job.
To cancel, proceed as follows:
1 Check if
2 Press the CANCEL key.
Print Cancel? appears in the message display and then interface to be canceled.
3
Parallel
USB
Serial
Option (appears only when an option network interface card is installed)
Press the CANCEL key again if you wish to stop the cancellation of printing.
4 Select the interface to cancel using
from the selected interface will stop. Cancelling data appears in the message display
and printing stops after the current page is printed.
• Resets numeric values, or cancels a setting procedure.
• Used to stop the sounding of the alarm buzzer an error occurs.
• When pressed during mode selection, terminates the setting and the printer returns to the
Ready condition.
• Used to select the emulation, font, character code set; to read an CompactFlash card, and
more.
Used to access a desired item or enter numeric values. In some of the control procedures, the >
and < keys are used to enter or exit a sub item.
Used to access a desired item or enter of numeric values. In some of the control procedures, the
> and < keys are used to enter or exit a sub item.
Used as the < key in the mode selection function.
Understanding the Operator Panel
The operator panel keys are used to
configure the printer. Note the
certain keys have the secondary
function.
GO
CANCEL MENU ENTER
?
Settings made with these keys effect only the interface currently in use.
Processing is displayed in the message display.
(appears only when an option serial interface board kit is installed)
the or key and then press the ENTER key. Printing
•Used as the > key in the mode selection function.
• Displays online help messages on the message display when paper jam errors occur. When
?
ENTER
pressed in the
while the online help is displayed, cancels the online help.
†
Finalizes numeric values and other selections.
Ready condition, displays explanations of online help messages. When pressed
Table 1-5
†If you hold down the ENTER key and press the MENU key when Ready is shown on this printer, the AdministrationID menu
will be displayed. This menu is the setting menu for administration under the Account Management System and is normally not
used. Press the MENU key to return to the Ready display.
1-5
Understanding the Operator Panel
Menu System Road Map
This section explains how to use the menu selection system. The MENU key
on the operator panel allows you to use the menu to set or change the
printer environment such as the number of copies to make, emulation, etc.,
to your specific needs. Settings can be made when Ready is indicated on
the printer message display.
The printer obeys the most recently received printer settings sent from
the application software, or from the printer driver, which take priority
Note
over operator panel settings.
The following is the hierarchy diagram of the menu selection system of the
printer.
The vertical transition is made with the and keys and horizontal
transition is made with the > and < keys. To change or finalize
configuration on an item, use the ENTER key.
Ready
PAR A4 PLAIN
MENU
Print
Menu Map
Print
Status Page
e-MPS >
>Quick Copy
>Private/Stored
>Print VMB Data
>List of VMB
>List of
Code JOB
>e-MPS >
Configuration
These items will not appear unless the printer
is installed with the applicable option unit.
>>Quick Copy
>>Temp.Code JOB
Size
>>Perm.Code JOB
Size
>>VMB Size
Continued on next page
1-6
Continued from previous page
Understanding the Operator Panel
Interface >
Parallel
USB
Interface >
Serial
Interface >
Option
>Parallel I/F
Auto
Normal
High Speed
Nibble (high)
>Baud Rate
9600
>Data Bits
8
>Stop Bits
1
>Parity
None
>Protocol
DTR (pos.)&XON
>NetWare
Off
>NetWare >
On
>TCP/IP
Off
On
>Ether Talk
Off
>>NetWare Frame
Auto
>>DHCP
OFF
>>IP Address
Emulation
PCL 6
Emulation >
KPDL
Emulation >
KPDL (AUTO)
Emulation
Line Printer
Emulation
IBM Proprinter
Emulation
DIABLO 630
Emulation
EPSON LQ-850
>OPT. StatusPage
Off
>Print KPDL errs
Off
On
>Alt. Emulation
PCL 6
>Print KPDL errs
Off
On
>>Subnet Mask
>>Gateway
Continued on next page
1-7
Understanding the Operator Panel
Continued from previous page
Font >
Page Set >
Font Select >
Internal
>
Option
>Code Set
IBM PC-8
>List of
Internal Fonts
>List of
Option Fonts
>Copies
001
>Orientation
Portrait
Landscape
>Page Protect
Auto
On
>LF Action
LF only
CR and LF
Ignore LF
>CR Action
CR only
CR and LF
Ignore CR
>Wide A4
Off
On
>> I000
>>Courier
Dark
Regular
>>Letter Gothic
Regular
Dark
>>Size
012.00
>>Pitch
10.00 cpi
Continued on next page
1-8
Continued from previous page
Understanding the Operator Panel
Print Quality >
>KIR Mode
On
Off
>Ecoprint Mode
Off
On
>Resolution
Fast 1200 mode
300 dpi
600 dpi
>Print Density
03
Hard Disk > >Read Data
>Write Data
>Delete Data
>List of
Partitions
RAM Disk Mode
Off
RAM Disk Mode
On
Memory Card >
>RAM Disk Size
>Read Data
>Write Data
>Delete Data
>List of
Partitions
>Read Fonts
>Read Data
>Write Data
>Delete Data
>Format
>List of
Partitions
Continued on next page
1-9
Understanding the Operator Panel
Continued from Previous page
Paper Handling >
>MP Tray Mode
Cassette
>MP Tray Size
A4 or Letter
>MP Tray Type
Plain
>EF Size
DL or Business
>EF Type
Envelope
>Cassette Size
A4
>Cassette Size >
Custom
>Cassette Type
Plain
>Feed Select
Cassette
>Duplex Mode
None
>Stack Select
Top tray FaceDn
>Stack Select
RearTray FaceUp
>Sorter Mode
Sorter
>>Unit
mm
inch
>>X Dimension
>>Y Dimension
Life Counters >
Continued on next page
>Override A4/LT
Off
>Override A4/LT
On
>Type Adjust >
Custom 1
>Reset Type
Adjust
>Total Print
0123456
>New Toner
Installed
>>Paper weight
Normal 2
>>Duplex Path
Enable
Disable
1-10
Continued from previous page
Understanding the Operator Panel
Others >
>MSG Language
English
>Form Feed
Time Out 030sec.
>Sleep Timer >
015 min.
>Print HEX-DUMP
>Printer Reset
>Resource Prot.
Off
Permanent
Perm / Temp
>Buzzer
On
Off
>Auto Continue >
Mode On
Mode Off
>Finishing >
>Service >
>>Sleep Mode
On
Off
>>Auto Continue
Timer 030sec.
>>Duplex
Off
On
>>Print
Status Page
>>Print
Event Log
>>Developer
†
>>DRUM-CTRL
00
>>Drum
†
Since this menu is provided for service,
†
†
normally you need not use it.
1-11
Printing Test Pages
Printing Test Pages
This section explains the procedure for printing the printer’s internal
information using the menu selection system. The menu map is usefull as a
reference to guide yourself through the menu selection system.
The status page is a list of parameters and settings for most basic printer
configurations. You may be required to produce a status page when
requesting service to the printer.
Menu Map
The printer prints a full list of menu selection system. Note that menus
indicated on the list may vary depending on which option units are
installed on the printer.
1
2
Press the MENU key.
Press the or key repeatedly until Print Menu Map appears.
Print
Menu Map
Press the ENTER key. A question mark (?) appears.
3
Print
Menu Map ?
Press the ENTER key again. The printer prints a menu map.
4
1-12
Sample MENU MAP
Printing Test Pages
FS-1920 Page Printer
MENU MAP
1-13
Printing Test Pages
Status Page
If you want to check the printer's current status, including memory
available and option settings, you can find the information you need on the
status page.
Press the MENU key.
1
Press the or key repeatedly until Print Status Page appears.
2
Print
Status Page
Press the ENTER key. A question mark (?) appears.
3
Print
Status Page ?
Press the ENTER key again. The printer prints a status page.
4
For a full description of the status page, see the following pages.
1-14
Loading...